Host copolymers containing pendant carbazole and oxadiazole groups: Synthesis,characterization and optoelectronic applications for efficient green phosphorescent OLEDs

Vinyl copolymers (PCOn), containing pendant carbazole and aromatic 1,3,4‐oxadiazole attached with dodecyloxy group, were prepared from their corresponding precursor poly(9‐vinyl carbazole‐co‐4‐vinylbenzyl chloride) (PCBn) by the Williamson condensation (n: mole% of 4‐vinylbenzyl chloride). These copolymers were used as host materials for green phosphorescent light‐emitting diodes after blending 4 wt % of Ir(ppy)₃. PL spectra of the PCOn films showed the formation of excimer or exciplex. The phosphorescent EL devices were fabricated with a configuration of ITO/PEDOT:PSS/host copolymers:Ir(ppy)₃/BCP/Ca/Al. The PL and EL spectra of the blends [PCOn:Ir(ppy)₃] revealed dominant green emission at 517 nm attributed to Ir(ppy)₃ due to efficient energy transfer from the host to Ir(ppy)₃. Efficient green phosphorescent OLEDs was obtained when employing copolymer PCO16 as the host and Ir(ppy)₃ as the guest. The maximal luminance efficiency and the maximal luminance of this device were 17.9 cd/A and 19,903 cd/m², respectively. After doped with Ir(ppy)₃, the morphology of the films, both controlled PCO20 and PCO20 with attached dodecyloxy groups, were investigated by tapping‐mode AFM and FE‐SEM. The film of PCO20 exhibited uniform, featureless image and showed much better device performance than PCO20, which have been attributed to good compatibility of PCO20 with Ir(ppy)₃. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5180–5193, 2008     

Synthesis and characterization of a polyfluorene containing carbazole and oxadiazole dipolar pendent groups and its application to electroluminescent devices

We have synthesized a blue‐light‐emitting polyfluorene (PF) derivative ( PF‐CBZ‐OXD ) that presents bulky hole‐transporting carbazole and electron‐transporting oxadiazole pendent groups functionalized at the C‐9 positions of alternating fluorene units. The results from photoluminescence and electrochemical measurements indicate that both the side chains and the PF main chain retain their own electronic characteristics in the copolymer. An electroluminescent device incorporating this polymer as the emitting layer was turned on at 4.5 V; it exhibited a stable blue emission with a maximum external quantum efficiency of 1.1%. Moreover, we doped PF‐CBZ‐OXD and its analogue PF‐TPA‐OXD with a red‐light‐emitting iridium phosphor for use as components of phosphorescent red‐light emitters to investigate the effect of the host's HOMO energy level on the degree of charge trapping and on the electrophosphorescent efficiency. We found that spectral overlap and individual energy level matching between the host and guest were both crucial features affecting the performance of the electroluminescence devices. Atomic force microscopy measurements indicated that the dipolar nature of PF‐CBZ‐OXD , in contrast to the general nonpolarity of polydialkylfluorenes, provided a stabilizing environment that allowed homogeneous dispersion of the polar iridium triplet dopant. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2925–2937, 2007     

Single layer light‐emitting diodes from copolymers comprised of mesogen‐jacketed polymer containing oxadiazole units and PVK

A series of copolymers PCt‐co‐Poly(N‐vinylcarbazole) were synthesized through common radical polymerization, in which P‐Ct as a kind of mesogen‐jacketed liquid crystalline polymer was introduced, and the effects of copolymers composing variation on the optical properties of the polymers were studied. The structures and properties of the copolymers were characterized and evaluated by thermogravimetric (TGA), UV, photoluminescence (PL), cyclic voltammetry (CV), and electroluminescence (EL) analyses. All the polymers enjoy high thermal stability. PL peaks in the film show blue‐shift compared with in solutions and fluorescent quantum efficiency decreased with the N‐vinylcarbazole (nvk) content increasing, which supported the efficient energy transfer from nvk units to the oxadiazole units. CV revealed that, with the incorporation of nvk to the copolymer, these copolymers had high‐lying HOMO energy levels ranging from ?5.94 to ?6.09 eV. Single‐layer light‐emitting diodes (LEDs) with the configuration of ITO/PEDOT/PCt‐nvk/Mg:Ag/Ag were fabricated, which emit a blue light around 450 and 490 nm with a maximum luminance of 703 cd/m². The device performance varies with the content of nvk and device configuration, with device configuration ( b ) and PCt‐nvk8 giving the best value of external quantum efficiency of 0.27%. We show here that by proper design copolymer structure and modification of device configuration can exhibit strong blue EL in higher external quantum efficiency. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1843–1851, 2008     

Vinyl copolymers containing pendant 1,4‐distyrylbenzene and 1,3,4‐oxadiazole chromophores: Preparation and optoelectronic properties

We prepared two vinyl copolymers P1 and P2 containing pendant distyrylbenzene and aromatic 1,3,4‐oxadiazole derivatives, respectively, from their precursor poly(styrene‐ran‐4‐vinylbenzyl chloride) (M_w = 11,400, PDI = 1.18), which had been prepared by the controlled radical polymerization (RAFT). Two main chain polymers containing similar isolated distyrylbenzene ( P3) and aromatic 1,3,4‐oxadiazole ( P4 ) chromophores were also synthesized for comparative study. The resulted copolymers ( P1 – P4 ) are soluble in common organic solvents and are basically amorphous materials with 5% weight‐loss temperature higher than 360 °C. The PL spectral results reveal that the architecture of P1 prevents the formation of inter‐ or intramolecular interaction. The HOMO and LUMO levels of P2 , estimated from cyclic voltammetric data, are ?5.96 and ?3.81 eV, respectively, which are much lower than those of P1 (?5.12 and ?3.11 eV). The emission of blend from P1 and P2 are contributed mainly from distyrylbenzene fluorophore (～450 nm) owing to efficient energy transfer. Moreover, the blend exhibits three kinds of redox behavior depending on their weight ratios. The luminance and current efficiency of the EL device lpar;ITO/PEDOT/ MEH ‐ PPV + P2 /Al) are 503 cd/m² and 0.11 cd/A, which can be improved to 1285 cd/m² and 0.44 cd/A, respectively, as the weight ratio of P2 increases from 0 to 20%. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5362–5377, 2006     

Copolyfluorenes containing pendant bipolar carbazole and 1,2,4‐triazole groups: Synthesis,characterization, and optoelectronic applications

Three novel copolyfluorenes ( P1 ‐ P3 ) containing pendant bipolar groups (2.5–7.7 mol %), directly linked hole‐transporting carbazole and electron‐transporting aromatic 1,2,4‐triazole, were synthesized by the Suzuki coupling reaction and applied to enhance emission efficiency of polymer light‐emitting diodes based on conventional MEH‐PPV. The bipolar groups not only suppress undesirable green emission of polyfluorene under thermal annealing, but also promote electron‐ and hole‐affinity of the resulting copolyfluorenes. Blending the bipolar copolyfluorenes with MEH‐PPV results in significant enhancement of device performance [ITO/PEDOT:PSS/MEH‐PPV+ P1 , P2 or P3 /Ca(50 nm)/Al(100 nm)]. The maximum luminance and luminance efficiency were enhanced from 3230 cd/m² and 0.29 cd/A of MEH‐PPV‐only device to 15,690 cd/m² and 0.81 cd/A (blend device with MEH‐PPV/ P3 = 94/6 containing about 0.46 wt % of pendant bipolar residues), respectively. Our results demonstrate the efficacy of the bipolar copolyfluorenes in enhancing emission efficiency of MEH‐PPV. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Bipolar copolymers comprised mesogen‐jacketed polymer containing oxadiazole units and PVK as host materials for electroluminescent devices

Nonconjugated bipolar transport polymers have been developed as host materials for electroluminescent devices by incorporating both electron‐transporting and hole‐transporting functionalities into copolymers. The random copolymer PCt‐nvk3‐7 containing mesogen‐jacketed segment of P‐Ct have been synthesized and characterized. The effect of mesogen‐jacketed segment content of these bipolar copolymers on device performance has been investigated. The results of polymer light‐emitting diodes (PLEDs) show that the jacketed content of copolymers has a significant effect on device performance: lowering charge transport and facilitating the hole‐electron recombination leads to much higher current efficiency. Applying these high triplet random copolymers as host, the maximum current efficiency of 0.70 cd/A and the maximum brightness of 1872.8 cd/m² was achieved for PCt‐nvk3‐7 with an orange‐emitting complex dopant. The results suggest that the bipolar copolymers PCt‐nvks can be good host polymers for electrophosphorescent devices. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7861–7867, 2008     

Synthesis,characterization, and electroluminescent performance of a novel copolyfluorene containing pendant crown ether groups

Copolyfluorene PFC containing pendant crown ether moieties was prepared by the palladium‐catalyzed Suzuki coupling reaction. The photo‐physical and electrochemical properties were investigated by absorption, photoluminescence (PL) spectroscopy, and cyclic voltammetry to elucidate the influence of the crown ether groups. In film state, its PL spectra (peaked at 430 and 452 nm) show noticeable red‐shift relative to 423 and 448 nm of poly(9,9‐dihexylfluorene) ( PF ). Thermal annealing leads to appearance of new emission at about 520 nm which has been attributed to formation of excimer. The highest occupied molecular orbital and lowest unoccupied molecular orbital levels of PFC were estimated to be ?5.68 and ?2.65 eV which contributed to balanced charges injection. Double‐layer electroluminescent device using PFC as emitting layer (ITO/PEDOT:PSS/ PFC /Ca/Al) revealed maximum luminance (7910 cd/m²) and maximum luminance efficiency (2.3 cd/A) superior to those of PF device (860 cd/m², 0.29 cd/A). Moreover, inserting a PFC layer between the PF emitting layer and calcium cathode led to reduced turn‐on voltage (4.1 V), much lower than 7.1 and 6.6 V of the double‐layer PFC and PF devices, respectively, and enhanced device performance (2800 cd/m² and 0.53 cd/A). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2985–2995, 2009     

PCPP derivatives containing carbazole pendant as hole transporting moiety for efficient blue electroluminescence

The syntheses and characterization of poly((2,6‐(4,4‐bis(4‐((2‐ethylhexyl)oxy)phenyl)‐4H‐cyclopenta[def]phenanthrene))‐co‐(2,6‐(4,4‐bis(4‐(((9‐carbazolyl)hexyl)oxy)phenyl))‐4H‐cyclopenta[def]phenanthrene)) (BCzPh‐PCPPs) and poly((2,6‐(4,4‐bis(4‐((2‐ethylhexyl)oxy)phenyl)‐4H‐cyclopenta[def]phenanthrene))‐co‐(2,6‐(4‐(4‐(((9‐carbazolyl)hexyl)oxy)phenyl)‐4‐(4‐((2‐ethylhexyl)oxy)phenyl)‐4H‐cyclopenta[def]phenanthrene))) (CzPh‐PCPPs), with carbazole unit as pendants, are presented. The carbazole moiety, which can improve the hole injection ability, was introduced as a pendant on the PCPP backbone. The devices of the polymers with the configurations of ITO/PEDOT:PSS/polymers/Ca/Al generate EL emission with maximum peaks at 400–450 nm, CIE coordinates of (x = 0.11–0.29, y = 0.11–0.33), low turn‐on voltages of 4–6 V, maximum brightness of 60–810 cd/m², and luminescence efficiencies of 0.04–0.22 cd/A. The PL spectra of CzPh‐PCPPs films did not show any peak at around 550 nm, which corresponds to keto defect or aggregate/excimer formation, even after annealing for 30 h at 150 °C in air. Out of the series, CzPh‐PCPP1 (PCPP derivative with 10% of carbazole moiety as pendant) shows blue emission with the maximum brightness of 810 cd/m² at 9 V, and the highest luminescence efficiency of 0.22 cd/A at 395 mA/cm². © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1327–1342, 2009     

New fluorene‐based copolymers containing oxadiazole pendant groups: Synthesis,characterization, and polymer stability

A series of fluorene‐based copolymers containing hole blocking/electron transporting diphenyloxadiazole units were synthesized by means of Suzuki‐Miyaura coupling of selected aromatic dibromo‐ and diboronato‐ derivatives catalyzed with a Pd(PPh₃)₄ catalyst. All of the copolymers with various composition of main‐chain units were characterized by SEC chromatography, NMR, UV–vis, fluorescence and IR spectroscopy, and DSC. The emission stability of fluorene copolymers was improved by the replacement of alkyl groups on the C‐9 carbon of fluorene with aryl groups or by the incorporation of anthracene units into the copolymer main chain. A comparison of luminescence properties of pristine and annealed thin layers of studied copolymers was performed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4532–4546, 2009     

Synthesis of electroluminescent copoly(aryl ether)s containing alternate 1,4‐distyrylbenzene derivatives and aromatic 1,3,4‐oxadiazole or 3,3″‐terphenyldicarbonitrile segments

New copoly(aryl ether)s ( P1 – P3 ) containing alternate 2,5‐dihexyloxy‐1,4‐di(m‐ethoxystyryl)benzene ( P1 , P2 ) or 2,5‐dihexyloxy‐1,4‐distyrylbenzene ( P3 ) chromophores and aromatic 1,3,4‐oxadiazole ( P1 ) or 3,3″‐terphenyldicarbonitrile ( P2 , P3 ) segments were prepared by Horner reaction ( P1 and P2 ) or nucleophilic displacement reaction ( P3 ). They are basically amorphous materials with 5% weight‐loss temperature above 410 °C. Their absorption, photoluminescence spectra, and quantum yields are dependent on the composition of the isolated fluorophores. The emissions are exclusively dominated by 1,4‐distyrylbenzene segments via excitation energy transfer from electron‐transporting 1,3,4‐oxadiazole ( P1 ) or 3,3″‐terphenyldicarbonitrile ( P2 , P3 ) chromophores. The HOMO and LUMO energy levels have been estimated from their cyclic voltammograms, and the observations confirm that oxidation and reduction start from the emitting 1,4‐distyrylbenzene and electron‐transporting segments, respectively, indicating that both carriers affinity can be enhanced simultaneously. Among the two‐layer PLED devices (ITO/PEDOT/ P1 – P3 /Al), P1 exhibits the best performance with a turn‐on field of 4 × 10⁵ V/cm and a maximum luminance of 225 cd/m². However, P2 emits green–yellow light (555 nm), owing to the excimer emission. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5009–5022, 2005     

Synthesis and electroluminescent properties of fluorene‐based copolymers containing electron‐withdrawing thiazole derivatives

We synthesized two fluorene‐based copolymers poly[(2,5‐bis(4‐hexylthiophen‐2‐yl)thiazolo[5,4‐day]thiazole‐5,5′‐diyl)‐alt‐(9,9′‐dioctylfluorene‐2,7‐diyl)] ( PF‐TTZT), and poly[(5,5′‐bis(4‐hexylthiophen‐2‐yl)‐2,2′‐bithiazole‐5,5′‐diyl)‐alt‐(9,9′‐dioctylfluorene‐2,7‐diyl)] (PF‐TBTT), which contain the electron‐withdrawing moieties, thiazolothiazole, and bithiazole, respectively. Through electrochemical studies, we found that these two polymers exhibit stable reversible oxidation and reduction behaviors. Moreover, the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of PF‐TBTT are lower than those of PF‐TTZT, and the bandgap of PF‐TBTT is smaller than that of PF‐TTZT. Thus the bithiazole moiety in PF‐TBTT is more electron‐withdrawing than the thiazolothiazole moiety in PF‐TTZT. Light‐emitting devices with indium tin oxide (ITO)/poly(3,4‐ethylene dioxythiophene):poly(styrenesulfonate)(PEDOT)/polymer/bis(2‐methyl‐8‐quinolinato)‐4‐phenylphenolate aluminum (BAlq)/LiF/Al configurations were fabricated. The performance of the PF‐TBTT device was found to be almost three times better than that of the PF‐TTZT device, which is because electron injection from the cathode to PF‐TBTT is much easier than for PF‐TTZT. We also investigated the planarity and frontier orbitals of the electron donor‐acceptor (D‐A) moieties with computational calculations using ab initio Hartree–Fock with the split‐valence 6‐31G* basis set. These calculations show that TBTT has a more nonplanar structure than TTZT and that the bithiazole moiety is more electron‐withdrawing than thiazolothiazole. These calculations are in good agreement with the experimental results. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7148–7161, 2008     

Synthesis and characterization of fluorene‐based copolymers containing benzothiadiazole derivative for light‐emitting diodes applications

Five new thermally robust electroluminescent fluorene‐based conjugated copolymers, including poly[2,7‐(9,9‐dioctylfluorene)‐co‐4,7‐{5,6‐bis(3,7‐dimethyloctyloxymethyl)‐2,1,3‐(benzothiadiazole)}] ( PFO‐P2C₁₀BT ) were synthesized and used to fabricate the efficient polymer light‐emitting diodes (PLEDs). The glass transition temperatures of the polymers were found to be higher than that of poly(9,9‐dialkylfluorenes) and are in the range 113–165 °C. We fabricated PLEDs in indium‐tin oxide/PEDOT/light‐emitting polymer/cathode configurations using either double‐layer LiF/Al or triple‐layer Alq₃/LiF/Al cathode structures. The new copolymers were found to have emission colors that vary from greenish blue (491 nm) to green (543 nm) depending on the copolymer composition. The maximum brightness and luminance efficiency of these PLEDs were found to be up to 5347 cd/m² and 1.51 cd/A at 10 V, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6762–6769, 2008     

Synthesis and characterization of a novel electroluminescent polymer based on a phenoxazine derivative

We report the preparation of a new electroluminescent polymer by the oxidative coupling copolymerization of N‐(4‐n‐butylphenyl)phenoxazine and 9,9‐di‐n‐butylfluorene with ferric(III) chloride. The reaction yields soluble polymers with a weight‐average molecular weight as high as 9000. The reactivity has been studied with respect to the reaction time, temperature, and feed ratio of the comonomers. Under optimum conditions, a copolymer with a 50% comonomer incorporation ratio can be obtained in a 75% yield. The polymers have been characterized with differential scanning calorimetry, cyclic voltammetry, and optical spectroscopy. A simple single‐layer light‐emitting‐diode device of an indium tin oxide/polymer/Mg–Ag structure shows a luminance of 200 cd/m² at an 18‐V operating voltage. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4338–4345, 2006     

Synthesis and electroluminescent properties of polyfluorene‐based conjugated polymers containing bipolar groups

A bipolar dibromo monomer, bis‐(4‐bromophenyl)[4‐(3,5‐diphenyl‐1,2,4‐ triazole‐4‐yl)‐phenyl]amine ( 9 ), containing electro‐rich triphenylamine and electro‐deficient 1,2,4‐triazole moieties was newly synthesized and characterized. Two fluorescent fluorene‐based conjugated copolymers ( TPAF , TPABTF ) were prepared via facile Suzuki coupling from the dibromo bipolar monomer, 4,7‐dibromo‐2,1,3‐benzothiadiazole ( BTDZ ), and 9,9‐dioctylfluorene. They were characterized by molecular weight determination, IR, NMR, DSC, TGA, solubility, absorption and photoluminescence spectra, and cyclic voltammetry. The polymers showed good solubility in common organic solvents such as dichloromethane, chloroform, tetrahydrofuran, and dichlorobenzene at room temperature. They had glass transition temperatures (T_g) higher than 135 °C and 5% degradation temperatures in nitrogen atmosphere were higher than 428 °C. Single layer polymer light‐emitting diodes (PLED) of ITO/PEDOT:PSS/polymer/metal showed a blue emission at 444 nm and Commission Internationale de I'Eclairage (CIE) 1931 color coordinates of (0.16, 0.13) for TPAF . The device using TPABTF as emissive material showed electroluminescence at 542 nm with CIE1931 of (0.345, 0.625), low turn‐on voltage of 5 V, a maximum electroluminance of 696 cd/m², and a peak efficiency of 2.02 cd/A. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6231–6245, 2009     

Synthesis of conjugated copolymers containing phenothiazinylene vinylene moieties and their electrooptic properties

Four different types of conjugated copolymers, consisting of alternating structures of phenothiazinylene vinylene and phenylene vinylene derivatives such as phenylene vinylene, 1,1′‐biphenyl‐4,4′‐ylene vinylene, 2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylene vinylene, and 9,10‐anthrylene vinylene, were prepared by Horner–Emmons condensation between appropriate diphosphonates and dialdehydes. Single‐layer and double‐layer light‐emitting diodes were fabricated with the synthesized conjugated polymers, and their electroluminescent properties were investigated. Poly(N‐2‐ethylhexyl‐3,6‐phenothiazinylene vinylene‐alt‐9,10‐anthrylene vinylene), containing phenothiazinylene vinylene and anthrylene vinylene as repeat units, emitted a reddish‐orange color with Commission Internationale de l'Eclairage coordinates of x = 0.6173 and y = 0.3814 that was very similar to the National Television System Committee standard red, and it showed a bipolar carrier‐injection/transporting capability caused by electron‐withdrawing anthracene and electron‐donating amino groups. Poly[N‐2‐ethylhexyl‐3,6‐phenothiazinylene vinylene‐alt‐2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylene vinylene], containing phenothiazinylene vinylene and dialkoxy phenylene vinylene moieties, showed excellent hole‐injection/transporting capability. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2502–2511, 2003     

Synthesis of copolyfluorenes containing green chromophores based on triphenylamine unit and their application in light‐emitting diodes

Two series of new copolyfluorenes ( PFTP, PFTT ) were prepared by the Suzuki coupling reaction from two green‐emitting dibromo monomers (TP‐Br, TT‐Br) based on triphenylamine unit to be applied in white light electroluminescent devices. They were characterized by molecular weight determination, elemental analysis, DSC, TGA, absorption and photoluminescence spectra, and cyclic voltammetry. The estimated actual contents of the TP and TT chromophores were lower than 7.8 mol % and 1.9 mol % for PFTP and PFTT , respectively. In film state both copolyfluorenes showed photoluminescence at 400–470 and 470–600 nm originated from fluorene segments and the chromophores, respectively, due to incomplete energy transfer. Light‐emitting diodes with a structure of ITO/PEDOT:PSS/copolymer/Ca(50 nm)/Al(100 nm) showed major emission at 493–525 nm, plus minor emission at 400–470 nm when chromophore contents were low. The maximum brightness and maximum current efficiency of PFTP2 device were 8370 cd/m² and 1.47 cd/A, whereas those of PFTT1 device were 9440 cd/m² and 1.77 cd/A, respectively. Tri‐wavelength white‐light emission was realized through blending PFTT1 with poly(9,9‐dihexylfluorene) and a red‐emitting iridium complex, in which the maximum brightness and CIE coordinates were 6880 cd/m² and (0.31, 0.33), respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1553–1566, 2009     

Synthesis,characterization, and optoelectronic properties of hyperbranched polyfluorenes containing pendant benzylether dendrons

Linear polyfluorenes with low generation of side benzylether dendrons ( PLG0 , PLG1 ) and hyperbranched polyfluorenes with 1,3,5‐benzene branch unit ( PHG0 and PHG1 ) were prepared by the Suzuki coupling reaction to investigate the structural effect on optoelectronic properties. Their optical properties, both in solution and film state, were investigated using absorption and photoluminescence (PL) spectra. The excimer emission of polyfluorene at about 530 nm, induced by thermal annealing, was completely suppressed by the hyperbranched structure, but the suppression was not obvious by the side benzylether dendrons. The optoelectronic performance of the EL devices (ITO/PEDOT:PSS/polymer/Ca/Al) was strongly dependent upon chemical structures of the emitting polyfluorenes. The hyperbranched PHG0 with zero generation of benzylether side groups revealed the best device performance, with maximal luminance and maximal luminance efficiency of 2350 cd/m² and 0.33 cd/A, respectively. The results suggest that incorporation of branch units with low generation of benzylether dendrons is an effective way to improve annealing stability and EL performance of the polyfluorenes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5945–5958, 2008     

Vinyl copolymers containing pendant 1,3,4-oxadiazole chromophores: Preparation and electrochemical and electroluminescent properties

Three vinyl copolymers (P1–P3) containing pendant aromatic 1,3,4-oxadiazole derivatives were prepared from their precursor poly(styrene-ran-4-vinylbenzyl chloride) (weight-average molecular weight = 11,400, polydispersity index = 1.18), which had been synthesized by controlled radical polymerization (reversible addition–fragmentation chain transfer). The copolymers were readily soluble in common organic solvents and were basically amorphous materials with 5% weight loss temperatures higher than 360°C. The photoluminescence spectroscopy results revealed that the architectures of P2 and P3 suppressed aggregate formation in the solid state. The LUMO levels of P2 (−3.10 eV) and P3 (−3.09 eV), estimated from cyclic voltammetry data, were much higher than that of P1 (−3.81 eV). The HOMO levels were in the order of P3 (−5.37 eV) > P2 (−5.77 eV) > P1 (−5.96 eV). However, both the HOMO and LUMO levels of P1–P3 were much lower than that of poly[2-methoxy-5-(2′-ethylhexoxy)-p-phenylenevinylene] (MEH-PPV) because of the electron-withdrawing characteristics of the pendant aromatic 1,3,4-oxadiazole groups. The luminance (5860 cd/m²) and current efficiency (1.45 cd/A) of an electroluminescence device [indium tin oxide/poly(3,4-ethylene dioxythiophene)/MEH-PPV/Al] were improved significantly to 16,261 cd/m² and 4.79 cd/A, respectively, through blending with P2 (50/50). This study suggests that copolymers P1–P3 are versatile materials for electron-transport/injection applications. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2259–2272, 2007     

Copolyfluorenes containing phenothiazine or thiophene derivatives: Synthesis,characterization, and application in white‐light‐emitting diodes

Four copolyfluorenes chemically doped with 0.1 and 1 mol % 3,7‐bis[2‐thiophene‐2‐yl)‐2‐cyanovinyl]phenothiazine ( PFPhT ) or 2,5‐bis[2‐(thiophene‐2‐yl)‐2‐cyanovinyl]thiophene chromophores ( PFThT ) were synthesized using the Suzuki coupling reaction and applied in white‐light‐emitting devices. They were characterized by GPC, elemental analysis, DSC, TGA, optical spectra, and cyclic voltammetry. They exhibited good thermal stability (T_d > 420 °C) and moderate glass transition temperatures (>95 °C). The PhT‐Br and ThT‐Br showed PL peaks at 586 and 522 nm (with a shoulder at 550 nm). In film state, PL spectra of the copolymers comprised emissions from the fluorene segments and the chromophores due to incomplete energy transfer. Both monomers exhibited low LUMO levels around ?3.50 to ?3.59 eV, whereas the PhT‐Br owned the higher HOMO level (?5.16 eV) due to its electron‐donating phenothiazine core. Light‐emitting diodes with a structure of ITO/PEDOT:PSS/copolymer/Ca(50 nm)/Al(100 nm) showed broad emission depending on the chromophore contents. The maximum brightness and maximum current efficiency of PFPhT2 ( PFThT1 ) device were 8690 cd/m² and 1.43 cd/A (7060 cd/m² and 0.98 cd/A), respectively. White‐light emission was realized by further blending PFPhT2 with poly(9,9‐dihexylfluorene) (w/w = 10/1), with the maximum brightness and maximum current efficiency being 10,600 cd/m² and 1.85 cd/A. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 833–844, 2009     

Synthesis and optoelectronic properties of luminescent poly(p‐phenylenevinylene) derivatives containing electron‐transporting 1,3,4‐oxadiazole groups

Three random copolymers ( P1–P3 ) comprising phenylenevinylene and electron‐transporting aromatic 1,3,4‐oxadiazole segments (11, 18, 28 mol %, respectively) were prepared by Gilch polymerization to investigate the influence of oxadiazole content on their photophysical, electrochemical, and electroluminescent properties. For comparative study, homopolymer poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐p‐phenylenevinylene] ( P0 ) was also prepared by the same process. The polymers ( P0–P3 ) are soluble in common organic solvents and thermally stable up to 410 °C under a nitrogen atmosphere. Their optical properties were investigated by absorption and photoluminescence spectroscopy. The optical results reveal that the aromatic 1,3,4‐oxadiazole chromophores in P1–P3 suppress the intermolecular interactions. The HOMO and LUMO levels of these polymers were estimated from their cyclic voltammograms. The HOMO levels of P0–P3 are very similar (?5.02 to ?5.03 eV), whereas their LUMO levels decrease readily with increasing oxadiazole content (?2.7, ?3.08, ?3.11, and ?3.19 eV, respectively). Therefore, the electron affinity of the poly(p‐phenylenevinylene) chain can be gradually enhanced by incorporating 1,3,4‐oxadiazole segments. Among the polymers, P1 (11 mol % 1,3,4‐oxadiazole) shows the best EL performance (maximal luminance: 3490 cd/m², maximal current efficiency: 0.1 cd/A). Further increase in oxadiazole content results in micro‐phase separation that leads to performance deterioration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4377–4388, 2007