Photoinitiated grafting of maleic anhydride onto polypropylene

The photoinitiated grafting of maleic anhydride (MAH) onto polypropylene with the use of benzophenone (BP) as the initiator has been investigated. In comparison with the process of thermally initiated grafting with peroxide as the initiator, photoinitiated grafting affords a higher grafting efficiency. The efficient photografting sensitized by BP can be explained by two possible mechanistic processes: the sensitization of the formation of the excited triplet state of MAH by BP and electron transfer followed by proton transfer between MAH and the benzopinacol radical, which may operate together. In the former case, the generated MAH excited triplet state abstracts a hydrogen from the polymer substrate to initiate grafting. A rate constant of 3.6 × 10⁹ M ^?1 s ^?1 has been determined by laser flash photolysis for the process of quenching the excited triplet state of BP with ground‐state MAH. In comparison, the rate constant for the quenching of the excited triplet state of BP by hydrogen abstraction has been determined to be 4.1 × 10⁵ M ^?1 s ^?1. In a study of photografting using a model compound, 2,4‐dimethylpentane, as a small‐molecule analogue of polypropylene, the loss of BP was significantly reduced upon the addition of MAH, and this is consistent with the proposed mechanistic processes. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1953–1962, 2004     

Effect of the initial maleic anhydride content on the grafting of maleic anhydride onto isotactic polypropylene

A series of ¹³C‐enriched maleic anhydride grafted isotactic polypropylene samples were prepared in solution at 170 °C by changes in the initial maleic anhydride content. The NMR spectra of the samples showed that the signals of the maleic anhydride attached to the tertiary carbons of the isotactic polypropylene chains increased considerably with increasing maleic anhydride content, whereas the signals of the maleic anhydride on the radical chain ends (with a single bond) arising from β scission did not. On the other hand, the signals of the maleic anhydride on the radical chain ends with double bonds increased markedly with increasing maleic anhydride content, and this suggested that β scission could occur extensively after maleic anhydride was attached to the tertiary carbons. As a result, the molecular weight of the grafted polypropylene decreased significantly with increasing maleic anhydride content in this study. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5529–5534, 2005     

Peroxide-initiated grafting of maleic anhydride onto linear and branched hydrocarbons

The structural features of the grafting of maleic anhydride onto low-molecular-weight compounds have been elucidated using several spectroscopic and analytical techniques. Conclusive evidence for the occurrence of singly grafted anhydride residues in multiply grafted products has been established using 2,3-¹³C₂ labeled maleic anhydride. In homogeneous solution, at the low concentrations of maleic anhydride employed, there is little evidence for oligomeric or polymeric grafts to dodecane, pristane, or squalane. The results suggest that isothermal grafting of maleic anhydride to hydrocarbon polymers should also lead to a predominance of single grafts. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3817–3825, 1999     

Molecular characterization of maleic anhydride-functionalized polypropylene

This work deals with the molecular characterization of maleic anhydride melt-functionalized polypropylene (PP-g-MA). The functionalization mechanism, the nature, the concentration, and the location of grafted anhydride species onto the polypropylene chain are discussed. The polypropylene functionalization was performed using a pre-heated Brabender Plastograph (190°C, 4 min of mixing time). Several concentrations of maleic anhydride and organic peroxide were used for this study. In those experimental conditions, the organic peroxide undergoes an homolytic rupture and carries out a polypropylene tertiary hydrogen abstraction. The resulting macroradical undergoes a β-scission leading to a radical chain end which reacts with maleic anhydride. When a termination reaction occurs at this first step a succinic type anhydride chain end is obtained. However, oligomerization of maleic anhydride is found to occur more frequently leading to poly (maleic anhydride) chain end. Concentration of both anhydride types and minimal length of the grafted poly (maleic anhydride) were determined. A fraction of maleic anhydride does not react with polypropylene or homopolymerize leading to nongrafted poly (maleic anhydride). © 1995 John Wiley & Sons, Inc.     

A kinetic study on grafting of maleic anhydride onto a thermoplastic elastomer

Maleation of a thermoplastic elastomer, styrene-[ethylene-butylene]-styrene (SEBS) triblock copolymer, was carried out by a solution grafting reaction with maleic anhydride initiated by dicumyl peroxide. The reaction products from the graft reaction in xylene, commonly chosen as the solvent for maleation graft reactions, were identified using liquid chromatograph (LC), IR, and ¹³C-NMR. Side products from the graft reaction were identified by the LC analysis and, it was concluded that xylene affected the graft reaction through its active methyl groups. Reaction mechanisms were investigated by performing free radical kinetics analysis. The reaction orders and the apparent rate constant were estimated. It was concluded that a proper choice of the solvent might favor better graft efficiency. © 1993 John Wiley & Sons, Inc.     

Glass bead grafting with poly(carboxylic acid) polymers and maleic anhydride copolymers

Glass beads were etched with acids and bases to increase the surface porosity and the number of silanol groups that could be used for grafting materials to the surfaces. The pretreated glass beads were functionalized using 3‐aminopropyltriethoxysilane (APS) coupling agent and then further chemically modified by reacting the carboxyl groups of carboxylic acid polymers with the amino groups of the pregrafted APS. Several carboxylic acid polymers and poly(maleic anhydride) copolymers, such as poly(acrylic acid) (PAA), poly(methacrylic acid) (PMA), poly(styrene‐alt‐maleic anhydride) (PSMA), and poly(ethylene‐alt‐maleic anhydride) (PEMA) were grafted onto the bead surface. The chemical modifications were investigated and characterized by FT‐IR spectroscopy, particle size analysis, and tensiometry for contact angle and porosity changes. The amount of APS and the different polymer grafted on the surface was determined from thermal gravimetric analysis and elemental analysis data. Spectroscopic studies and elemental analysis data showed that carboxylic acid polymers and maleic anhydride copolymers were chemically attached to the glass bead surface. The improved surface properties of surface modified glass beads were determined by measuring water and hexane penetration rates and contact angle. Contact angles increased and porosity decreased as the molecular weights of the polymer increased. The contact angles increased with the hydrophobicity of the attached polymer. The surface morphology was examined by scanning electron microscopy (SEM) and showed an increase in roughness for etched glass beads. Copyright © 2007 John Wiley & Sons, Ltd.     

Radical‐mediated modification of polypropylene: Selective grafting via polyallyl coagents

Selective graft modifications of polypropylene (PP) are demonstrated in which desirable functionality is introduced without the degradation that accompanies conventional radical‐mediated processes. A range of modification strategies is presented, each exploiting triallyl trimellitate (TATM) or its derivatives to counteract the effects of macroradical fragmentation on the molecular weight. Model compound studies, as well as examinations of atactic PP reaction products, show that allylic ester activation occurs predominately by a radical‐addition/hydrogen‐transfer sequence, with a limited propensity for telomerization. The cografting of TATM and maleic anhydride leads to maleated PP of a high melt viscosity, whereas the apparent incompatibility of TATM with vinyltrimethoxysilane requires the use of TATM‐assisted thiol–ene addition and/or diallyl silane grafting to produce moisture‐curable PP derivatives. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4882–4893, 2005     

Thermal behavior of the maleic anhydride modified poly(3-hydroxybutyrate)

Poly(3-hydroxybutyrate), PHB has been structurally modified through reaction with maleic anhydride, MA. Transesterification reaction was carried out fixing the PHB and MA and besides time and temperature the concentration of the triethylamine (used as catalyst) was changed. Glass transition, melting and crystallization temperature obtained from DSC curves and thermal degradation temperatures obtained from TG traces were used to evaluate the influence of the reaction conditions on the modification of PHB according to factorial design. On the base of the results the optimum conditions are to perform the PHB modification reaction with MA reaction at 110°C for 1 h with 5% v/v triethylamine.     

Maleic anhydride homopolymerization during melt functionalization of isotactic polypropylene

The homopolymerization of maleic anhydride was attempted at 190°C, during the melt-functionalization of polypropylene, either with or without organic peroxide using a Brabender plastograph. The free radical homopolymerization of pure maleic anhydride was also attempted either with or without organic peroxide, at 190°C, in vacuum-sealed glass vials. In all cases, free low molecular weight maleic anhydride oligomers were observed by low molecular weight size exclusion chromatography (SEC). This maleic anhydride homopolymerization tends to prove that the ceiling temperature of poly(maleic anhydride) probably lies above the previously published value of 160°C for these specific experimental conditions. © 1996 John Wiley & Sons, Inc.     

Graft copolymerization of maleic anhydride/styrene onto isotactic polypropylene using supercritical CO2

The free‐radical grafting of maleic anhydride (MAH) and styrene (St) onto isotactic polypropylene (iPP) was studied by thermal decomposition of dicumyl peroxide (DCP) using supercritical CO₂ as a solvent and swelling agent. Several effects of molar ratio of monomer, soaking temperature and time, reaction time, and reaction pressure on the graft degree were discussed. It was found that the addition of St to the grafting system as a comonomer could significantly enhance the graft degree of the grafted PP. Under the optimal reaction condition, the maximum of iPP grafting MAH and St in supercritical CO₂ medium was 10.58%. The chemical structures and properties of grafting copolymers were characterized by Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). The results showed that the supercritical CO₂ method had noticeable advantages over the existed method when compared, such as a lower temperature, a higher graft degree, easy separation, and environmentally benign. Copyright © 2007 John Wiley & Sons, Ltd.     

热重法测定高马来酸酐含量苯乙烯-马来酸酐共聚物的组成

高马来酸酐含量苯乙烯-马来酸酐共聚物(SMA)是一种具有优良耐热性、刚性和尺寸稳定性的新型高分子材料.由于SMA分子中含有极性很强、反应活性很高的酸酐官能团,所以它被广泛应用于涂料、粘合剂的改性剂、地板抛光的乳化剂、复合材料和颜料的分散剂、水处理剂等领域[1-5].     

Ultrasonically Initiated Grafting of Maleic Anhydride onto Poly(propylene)

This paper presents the studies on the grafting of MAH onto PP performed in solution by means of ultrasonic initiation. The effect of sonic intensity and monomer concentration on the amount of grafted MAH was investigated. It was found that grafting reaction could be initiated by ultrasound at ambient temperatures in the absence of an initiator. The quantity of product grafted was found to be 1.35%. It has been shown that optimum conditions for grafting are reached at an ultrasonic intensity of 300 W and a MAH concentration of 30%. PP‐g‐MAH is characterized by FTIR and XRD. DSC shows that the crystallinity of PP‐g‐MAH is lower than that of pure PP.

     

Grafting of maleic anhydride onto linear polyethylene: A Monte Carlo study

Monte Carlo simulation was used to study the graft of maleic anhydride (MAH) onto linear polyethylene (PE‐g‐MAH) initiated by dicumyl peroxide (DCP). Simulation results revealed that major MAH monomers attached onto PE chains as branched graft at higher MAH content. However, at extremely low MAH content, the fraction of bridged graft was very close to that of branched graft. This conclusion was somewhat different from the conventional viewpoint, namely, the fraction of bridged graft was always much lower than that of branched graft under any condition. Moreover, the results indicated that the grafting degree increased almost linearly to MAH and DCP concentrations. On the other hand, it was found that the amount of grafted MAH dropped sharply with increasing the length of grafted MAH, indicating that MAH monomers were mainly attached onto the PE chain as single MAH groups or very short oligomers. With respect to the crosslink of PE, the results showed that the fraction of PE‐(MAH)_n‐PE crosslink structure increased continuously, and hence the fraction of PE‐PE crosslink decreased with increasing MAH concentration. Finally, quantitative relationship among number average molecular weight of the PE, MAH, and DCP contents was given. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5714–5724, 2004     

液相色谱-串联质谱法测定淀粉及其制品中的顺丁烯二酸与顺丁烯二酸酐总含量

建立了测定淀粉及其制品中顺丁烯二酸和顺丁烯二酸酐总含量的高效液相色谱-串联质谱（HPLC-MS/MS）方法。样品经50%（v/v）甲醇提取、碱性条件下水解后,采用液相色谱-串联质谱对其进行分析,外标法定量。质谱分析采用电喷雾电离,负离子扫描,多反应监测模式。实验表明样品无明显的基质效应,添加水平为0.5~1000 mg/kg时,回收率为80.2%~115.3%,相对标准偏差（n=6）小于12%;方法检出限（LOD）为0.1 mg/kg,定量限（LOQ）为0.5 mg/kg。该方法提取效果好,具有良好的灵敏度、回收率和重复性,已被成功用于实际样品中顺丁烯二酸和顺丁烯二酸酐总含量的测定。     

Peroxide initiated maleic anhydride grafting: Structural studies on an ester‐containing copolymer and related substrates

Maleic anhydride (MAn) was grafted onto the low molecular weight esters methyl decanoate (MD) and methyl 2‐ethylhexanoate (MEH) using the free‐radical initiators Lupersol‐101 and ‐130; the esters were used as model compounds for the copolymer poly(ethylene‐co‐methyl acrylate). The grafted products in both cases were isolated from the unreacted ester and were subjected to extensive analysis using spectroscopic and chromatographic techniques. Analysis of the grafted material indicated the presence of one or more succinic anhydride (SAn) residues grafted to the ester. In the case of the multiply grafted material it has been established conclusively by ¹³C‐NMR using 2,3‐¹³C₂ labeled MAn that the multiple grafts exist as single units. A limited number of grafting experiments was performed on the copolymer in the melt and the graft‐modified copolymer was characterized spectroscopically. Single graft units were observed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1609–1618, 1999     

Metalization of polypropylene. I. Synthesis and melt free‐radical grafting of novel maleimides and methacrylates containing chelating moieties

Several chelating monomers with methacrylate and maleimide residues as polymerizable groups and diketone and aspartic acid residues as metal‐bonding groups were synthesized. A long‐chain aliphatic spacer was introduced to increase the solubility of the monomers in the polymer melt and to enhance the compatibility of grafted side chains and homopolymers with polypropylene (PP). PP was functionalized by melt free‐radical grafting, and some properties of the modified polymer were investigated. The grafting of a chelating methacrylic ester by injection molding afforded grafting yields of 30–50%. A comparison with products obtained by the grafting of commercially available acetoacetoxy methyl methacrylate showed the beneficial effect of the aliphatic spacer with respect to the grafting yield as well as the tensile strength and flexural modulus. The grafting of an aspartic acid based maleimide in an extruder afforded grafting yields of 80–95% and a significant increase in the surface wettability, as shown by contact‐angle measurements. A comparative study using samples obtained by the grafting of maleimidobenzoic acid indicated that the homogeneity‐increasing effect of the spacer was neutralized by the detrimental effect of the dicarboxylic chelating group. Nevertheless, the results showed that the maleimides were well suited for grafting by reactive extrusion because of their low susceptibility to homopolymerization under melt‐processing conditions. Preliminary metalization experiments showed the feasibility of plating without the use of corrosive etchants. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3400–3413, 2003     

Impact‐modified polypropylene/vermiculite nanocomposites

Impact‐modified polypropylene (PP)/vermiculite (VMT) nanocomposites toughened with maleated styrene–ethylene butylene–styrene (SEBS‐g‐MA) were compounded in a twin‐screw extruder and injection‐molded. VMT was treated with maleic anhydride, which acted both as a compatibilizer for the polymeric matrices and as a swelling agent for VMT in the nanocomposites. The effects of the impact modifier on the morphology and the impact, static, and dynamic mechanical properties of the PP/VMT nanocomposites were investigated. Transmission electron microscopy revealed that an exfoliated VMT silicate layer structure was formed in ternary (PP–SEBS‐g‐MA)/VMT nanocomposites. Tensile tests showed that the styrene–ethylene butylene–styrene additions improved the tensile ductility of the (PP–SEBS‐g‐MA)/VMT ternary nanocomposites at the expense of their tensile stiffness and strength. Moreover, Izod impact measurements indicated that the SEBS‐g‐MA addition led to a significant improvement in the impact strength of the nanocomposites. The SEBS‐g‐MA elastomer was found to be very effective at converting brittle PP/VMT organoclay composites into tough nanocomposites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2332–2341, 2003     

Multifunctional,water‐soluble,C60‐pendant maleic anhydride copolymer

Starting from the synthesis of a new methanofullerene derivative bearing an alcohol group, we report on the preparation of a water‐soluble, fullerene‐pendant copolymer. This multifunctional, C₆₀‐pendant maleic anhydride copolymer was characterized by conductometric titration, Fourier transform infrared and ultraviolet spectroscopy, thermogravimetric analysis, and cyclic voltammetry. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5814–5822, 2005     

Radiation grafting of styrene and maleic anhydride onto PTFE membranes and sequent sulfonation for applications of vanadium redox battery

Using γ-radiation technique, poly(tetrafluoroethylene) (PTFE) membrane was grafted with styrene (St) (PTFE-graft-PS) or binary monomers of St and maleic anhydride (MAn) (PTFE-graft-PS-co-PMAn), respectively. Then grafted membranes were further sulfonated with chlorosulfonic acid into ion-exchange membranes (denoted as PTFE-graft-PSSA and PTFE-graft-PSSA-co-PMAc, respectively) for application of vanadium redox battery (VRB). Micro-FTIR analysis indicated that PTFE was successfully grafted and sulfonated at the above two different conditions. However, a higher degree of grafting (DOG) was obtained in St/MAn binary system at the same dose due to a synergistic effect. Comparing with PTFE-graft-PSSA, PTFE-graft-PSSA-co-PMAc membrane showed higher water uptake and ion-exchange capacity (IEC) and lower area resistance (AR) at the same DOG. In addition, PTFE-graft-PSSA-co-PMAc with 6% DOG also showed a higher IEC and higher conductivity compared to Nafion membrane. Radiation grafting of PTFE in St/MAn binary system and sequent sulfonation is an appropriate method for preparing ion-exchange membrane of VRB.