Branched polymers through redox emulsion polymerization using peroxide monomer as the branching agent

Redox emulsion polymerization to branched vinyl polymers in the presence of 2-(tert-butylperoxy)ethyl methacrylate (BPEMA), ferrous sulfate, and sodium formaldehyde sulfoxylate (SFS) is reported in this paper. The peroxide monomer BPEMA containing alkyl peroxide was designed for high stability during preparation and storage. Nuclear magnetic resonance spectroscopy (NMR), Raman, and triple-detection size-exclusion chromatography (TD-SEC) measurements were used to reveal the polymerization procedure and provide evidence of branching structure. In the case of polymerization at St₁₀₀-BPEMA_1.0-FeSO_{4 0.5}-SFS_0.2, the molecular weight increased and decreased with conversion below and above 75% monomer conversion, respectively. The decreasing of molecular weight with monomer conversion came from the increased viscosity of the micelle, which makes it difficult for the formed macromolecules containing vinyl group to participate into polymerization. Finally, the molecular weight reached a value of M_{n. SEC} = 439,200 g/mol at 92.2% conversion. In addition, the Zimm branching factor, g', also decreased and increased with conversion below and above 60% conversion, respectively, and then the g' finally attends a value of 0.41, showing high degree of branching. Branched poly(methyl methacrylate) was also prepared through this strategy, showing a versatile approach to branched vinyl polymers.     

Development and application of methods for determination of residual monomer in dental acrylic resins using high performance liquid chromatography

Two high-performance liquid chromatographic methods for determination of residual monomer in dental acrylic resins are described. Monomers were detected by their UV absorbance at 230 nm, on a Nucleosil C18 (5 microm particle size, 100 A pore size, 15 x 0.46 cm i.d.) column. The separation was performed using acetonitrile-water (55:45 v/v) containing 0.01% triethylamine (TEA) for methyl methacrylate and butyl methacrylate, and acetonitrile-water (60:40 v/v) containing 0.01% TEA for isobutyl methacrylate and 1,6-hexanediol dimethacrylate as mobile phases, at a flow rate of 0.8 mL/min. Good linear relationships were obtained in the concentration range 5.0-80.0 microg/mL for methyl methacrylate, 10.0-160.0 microg/mL for butyl methacrylate, 50.0-500.0 microg/mL for isobutyl methacrylate and 2.5-180.0 microg/mL for 1,6-hexanediol dimethacrylate. Adequate assay for intra- and inter-day precision and accuracy was observed during the validation process. An extraction procedure to remove residual monomer from the acrylic resins was also established. Residual monomer was obtained from broken specimens of acrylic disks using methanol as extraction solvent for 2 h in an ice-bath. The developed methods and the extraction procedure were applied to dental acrylic resins, tested with or without post-polymerization treatments, and proved to be accurate and precise for the determination of residual monomer content of the materials evaluated.     

Radical polymerization in the presence of peroxide and reducing agent monomer for branched polymers

In this article, we report the radical polymerization in the presence of peroxide and commercially available or designed reducing agent monomer (RAM) for the preparation of branched poly(methyl methacrylate)s (PMMAs). The reaction behavior of the RAM was studied by NMR. Triple‐detection SEC (TD‐SEC) analysis was used to confirm the branching structure of the prepared PMMAs and to investigate the influence of peroxide concentration and RAM concentration on molecular weight and branched structure. The obtained branched PMMAs exhibited high molecular weights and relatively narrow polydispersities at high conversion of MMA. Interestingly, a significant increase in molecular weight and degree of branching of the obtained polymers are observed in higher BPO concentration, these results are quite different from that reported in the literature. The unique radical polymerization mechanism in the RAM/BPO redox‐initiated radical polymerization system resulted in branched PMMAs with high molecular weights at relatively high RAM and BPO concentrations. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 833–840     

Effect of monomer water solubility on cationic microemulsion polymerization of three components (water,surfactant, and monomer)

Here, we present the oil/water (O/W) microemulsion polymerization in three‐component microemulsions of n‐butyl acrylate, ethyl acrylate, and methyl acrylate, monomers with similar chemical structures but different water solubilities using the cationic surfactant dodecyl trimethyl ammonium bromide. The effects of monomer water solubility, initiator type and initial monomer concentration on the polymerization kinetics were studied. Reaction rates were high with final conversions between 70 and 98% depending on the monomer and reaction conditions. The final latexes were bluish, with a particle size ranging between 20 and 50 nm and polymer with molar masses in the order of 10⁶ g mol^?1. Increasing monomer water solubility resulted in a slower reaction rate, larger particles and a lower number density of particles. A higher reaction rate, larger average particle size and higher particle number density were obtained by increasing the monomer concentration. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Photoinitiated curing of mono‐ and bifunctional epoxides by combination of active chain end and activated monomer cationic polymerization methods

Photoinitiated cationic polymerization of mono‐ and bifunctional epoxy monomers, namely cyclohexeneoxide (CHO), 4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexanecarboxylate (EEC), respectively by using sulphonium salts in the presence of hydroxylbutyl vinyl ether (HBVE) was studied. The real‐time FTIR spectroscopic, gel content determination, and thermal characterization studies revealed that both hydroxyl and vinyl ether functionalities of HBVE take part in the polymerization. During the polymerization, HBVE has the ability to react via both active chain end (ACE) and activated monomer mechanisms through its hydroxyl and vinyl ether functionalities, respectively. Thus, more efficient curing was observed with the addition of HBVE into EEC‐containing formulations. It was also demonstrated that HBVE is effective in facilitating the photoinduced crosslinking of monofunctional epoxy monomer, CHO in the absence of a conventional crosslinker. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4914–4920, 2007     

Progress in liquid chromatography of synthetic electroneutral polymers

Recent achievements and anticipated future progress in high performance liquid chromatography of synthetic electroneutral polymers (polymer HPLC) are briefly reviewed. Basic retention mechanisms of polymer HPLC are explained and corresponding separation procedures are discussed. Advantages, drawbacks and pitfalls are presented of the most important polymer HPLC method, namely size exclusion chromatography. Principles of polymer HPLC methods combining various separation mechanisms within one chromatographic column (coupled procedures) or in a set of different chromatographic columns (two- and multi-dimensional procedures) are outlined.     

Effect of matrix polymerization conditions on the structure and adsorption properties of porous polymers on the basis of divinylbenzene,acrylonitrile, and methyl methacrylate

A comparative study was carried out on the matrix polymerization of divinylbenzene, acrylonitrile, and methyl methacrylate in SBA-15 silica mesoporous molecular sieves. The occupancy of the matrix mesopores by the starting monomer, the medium, the polymerization temperature and time as well as the means of removing the exotemplate were all found to affect the spatial organization and porous structure of the polymer materials. Surplus occupancy of the mesopores by the monomer (1–1.5), polymerization in vacuum, and an alkaline method for matrix removal were found to be optimal. IR spectroscopy was used to find the conversion of the starting polymer by following the relative change in intensity of the vinyl group bands. Translated from Teoreticheskaya i éksperimental'naya Khimiya, Vol. 44, No. 6, pp. 371–375, November–December, 2008.     

蛋白质的累加进样分离法的研究

蛋白质在梯度开始前到梯度开始后的一段时间内可以多次重复进样而其保留值无可觉察的变化的方法叫累加进样分离法。累加进样分离法在蛋白质制各色谱中有许多优点和重要的应用价值。     

Hybrid miniemulsion polymerization of acrylic/alkyd systems and characterization of the resulting polymers

The hybrid miniemulsion polymerization of acrylates in the presence of alkyd resin was carried out. The polymers obtained were characterized via gel permeation chromatography, carbon nuclear magnetic resonance, and differential scanning calorimetry analysis and selective extraction; they had a quite broad molecular weight distribution. The double bonds that served as grafting sites of the alkyd onto the polyacrylate were mostly those near acid groups. The final product contained some free alkyd and some free polyacrylate, but the predominant form was poly(acrylate-graft-alkyd). This confirmed that monomer droplet nucleation is the predominant nucleation mechanism for this hybrid miniemulsion polymerization system. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4159–4168, 1999     

Effect of cationic monomer on properties of fluorinated acrylate latex

Cationic fluorinated acrylate latex was prepared via semi-continuous emulsion copolymerization of cationic monomer and other monomers.The resultant latex and its film were characterized with dynamic light scattering detector and contact anglc meter. Influences of amount of DMDAAC on the propcrtics of resultant latex and its film were investigated in detail.Results show that the particle size of the latex has the minimum value and the zeta potential of the latex is increased when the amount of DMDAAC is increased.In addition,the particle size of the latex is unimodal distribution when the amount of DMDAAC is not more than 2.5%. However,the particle size of the latex is bimodal distribution when the amount of DMDAAC is more than 2.5%.The contact angle is varied slightly with the increase of amount of DMDAAC when it is not more than 2.5%.Nevertheless,the contact angle is decreased with the increase of the amount of DMDAAC when it is more than 2.5%.     

Effect of resin staging on frontal polymerization of dicyclopentadiene

In thermal frontal polymerization (FP), ambient temperature and staging conditions highly affect the resin behavior and front properties. This study describes the effect of staging conditions and resin reactivity on frontal ring opening metathesis polymerization of dicyclopentadiene in presence of phosphite-inhibited second-generation Grubbs catalyst. An experimental setup is designed to characterize and understand the effect of inhibitor concentration, incubation time, and incubation temperature on front velocity, activation time, and front temperature of the FP reaction. The results reveal that front properties are influenced by various factors, including available energy density of resin, stability of catalyst-inhibitor complex, resin temperature, and resin viscosity. An increase in staging temperature results in lower pot lives but faster gelation process and activation of FP reaction. Additionally, increasing the inhibitor concentration leads to slower fronts, higher activation times, and longer pot lives. The results of this study can be extended to other FP systems and can be used in design of new manufacturing processes and applications using FP.     

Chromatographic performance of molecularly imprinted polymers: Core‐shell microspheres by precipitation polymerization and grafted MIP films via iniferter‐modified silica beads

In this work, two different surface imprinting formats have been evaluated using thiabendazole (TBZ) as model template. The first format is a thin film of molecularly imprinted polymer (MIP) grafted from preformed silica particles using an immobilized iniferter‐type initiator (inif‐MIP). The second format is molecularly imprinted polymer microspheres with narrow particle size distribution and core‐shell morphology prepared by precipitation polymerization in a two‐step procedure. For the latter format, polymer microspheres (the core particles) were obtained by precipitation polymerization of divinylbenzene‐80 (DVB‐80) in acetonitrile. Thereafter, the core particles were used as seed particles in the synthesis of MIP shells by copolymerization of DVB‐80 and methacrylic acid in the presence of TBZ in a mixed solvent porogen (acetonitrile/toluene). The materials were characterized by elemental microanalysis, nitrogen sorption porosimetry and scanning (and transmission) electron microscopy. Thereafter, the imprinted materials were assessed as stationary phases in liquid chromatography. From this study it can be concluded that grafted MIP beads can be obtained in a simple and direct manner, consuming only a fraction of the reagents used typically to prepare imprinted particles from a monolithic imprinted polymer. Such materials can be used in the development of in‐line molecularly imprinted solid‐phase extraction methods. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1058–1066, 2010     

高效液相色谱法研究氨基酸测定中鸡蛋样品的微波水解

利用Pico-Tag高效液相色谱法（HPLC）研究了氨基酸分析中一种新的水解方法——微波水解法,鸡蛋样品以内含1％苯酚的6mol／L盐酸作为水解液水解,仅需7min即可求解完全,平均回收率为95％,相对标准偏差小于2％。方法简便、快速、准确、重现性好,适用于不同样品的水解处理。     

尼莫通注射液的含量测定及其稳定性的研究

 采用反相高效液相色谱法 ,以甲基睾丸素为内标 ,二极管阵列检测器检测 ,测定了尼莫通注射液中的尼莫地平的含量 ,研究了新一代钙离子拮抗剂尼莫通注射液的稳定性。光照、高温和低温实验结果表明 ,尼莫通注射液对低温和高温稳定 ,对光不稳定。尼莫通注射液的使用应注意避光保存。     

Micron-sized monodispersed polymer particles produced by seeded polymerization for the dispersion of high swelling of polymer particles with a large amount of monomer

 Micron-sized monodispersed polystyrene (PS)/poly(n-butyl methacrylate) composite particles were produced as follows. First, 1.77 μm-sized monodispersed PS seed particles produced by dispersion polymerization were dispersed in ethanol/water (1/2, w/w) medium dissolving poly(vinyl alcohol) as a stabilizer. n-Butyl methacrylate (BMA) monomer dissolving benzoyl peroxide initiator was emulsified in ethanol/water (1/2, w/w) solution of sodium dodecyl sulfate as emulsifier with ultrasonic homogenizer, and the BMA monomer emulsion was mixed with the PS seed emulsion. The PS seed particles absorbed with a large amount of BMA (about 150 times weight of the seed particles) for 2 h to about 10 μm in diameter while keeping good monodispersity and BMA droplets disappeared finally. The seeded polymerization was carried out at 70 °C after a certain amount of water was added to depress the redissolving of BMA from the swollen particles into the medium by raising from room temperature to the polymerzation temperature. Received: 21 February 1996 Accepted: 4 September 1996     

氯磺隆的高效液相色谱分析方法研究

本文研究了用高效液相色谱法测定新型除草剂氯磺隆含量的方法,在反相ODS柱上,用甲醇—水作流动相进行洗脱,紫外225nm检测,以萘作内标定量,方法快速、灵敏、准确,氯磺隆的最小检出量为0.8ng,变异系数为1.4%,回收率为100.7%,一次分析仅需3分钟。     

Rapid preparation of molecularly imprinted polymers by custom‐made microwave heating for analysis of atrazine in water

The rapid preparation of an atrazine‐imprinted polymer in a cost‐effective custom‐made microwave reactor was demonstrated. The polymerization reaction was accelerated by microwave heating, and the preparation time was greatly shortened (to 1 h). The resulting polymer was successfully applied as solid‐phase extraction adsorbent for the selective extraction and preconcentration of atrazine in environmental water samples. The binding capacity of the polymer was 1.11 mg/g polymer. The polymer provided selectivity with higher recovery of atrazine than of other interfering related contaminants. The proposed method had good limits of detection and quantitation at 0.20 and 0.60 ng/mL, respectively. The recoveries were from 83 to 89% at two spiking levels, with relative standard deviations less than 5%. This method was successfully applied to determine the atrazine levels in environmental water samples.     

Effect of thiol-containing monomer on the preparation of temperature-sensitive hydrogel microspheres

The main objective of this study is to prepare, thermally, sensitive microgel particles bearing thiol groups via precipitation polymerization of N-isopropylacrylamide (NIPAM), methylenebisacrylamide (MBA) and vinylbenzylisothiouronium chloride (VBIC) using 2-2′-azobis(2-amidinopropane)-dihydrochloride (V50) as initiator. The influence of various parameters has been investigated as a systematic study to point out the role of each reactant on polymerization conversion, and consequently, on particles and water-soluble polymer formation. The final microgel particles were characterized with respect to particle size and swelling ability. The aim of this paper is to complete our first short communication; Macromolecular symposia, 2000. 150: p. 283–290.     

Fabrication of molecularly imprinted resin via controlled polymerization applied in the enrichment of bisphenol A for plastic products

The addition of bisphenol A has been frequently used in industrial manufacturing because it imparts plastic products with characteristics such as transparency, durability, and excellent impact resistance. However, its widespread use raises concerns about potential leakage into the surrounding environment, which poses a significant risk to human health. In this study, molecularly imprinted polymers with specific recognition of bisphenol A were synthesized through surface-initiated atom transfer radical polymerization using poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) as the substrate, bisphenol A as the template molecule, 4-vinylpyridine as the monomer, and ethylene glycol dimethacrylate as the cross-linker. The bisphenol A adsorption capacity was experimentally investigated, and the kinetic analysis of the molecularly imprinted polymers produced an adsorption equilibrium time of 25 min, which is consistent with the pseudo-second-order kinetic model. The results of the static adsorption experiments exhibited consistency with the Langmuir adsorption model, revealing a maximum adsorption capacity of 387.2 μmol/g. The analysis of molecularly imprinted polymers-enriched actual samples using high-performance liquid chromatography demonstrated excellent selectivity for bisphenol A, with a linear range showing 93.4%–99.7% recovery and 1.1%–6.4% relative standard deviation, demonstrating its high potential for practical bisphenol A detection and enrichment applications.