Soluble narrow‐band‐gap copolymers containing novel cyclopentadithiophene units for organic photovoltaic cell applications

Five novel conjugated copolymers ( P1 – P5 ) containing coplanar cyclopentadithiophene (CPDT) units (incorporated with arylcyanovinyl and keto groups in different molar ratios) were synthesized and developed for the applications of polymer solar cells (PSCs). Polymers P1 – P5 covered broad absorption ranges from UV to near infrared (400–900 nm) with narrow optical band gaps of 1.38–1.70 eV, which are compatible with the maximum solar photon reflux. Partially reversible p‐ and n‐doping processes of P1 – P5 in electrochemical experiments were observed, and the proper molecular design for highest occupied molecular orbital (HOMO)/lowest unoccupied molecular orbital (LUMO) levels of P1 – P5 induced the highest photovoltaic open‐circuit voltage in the PSC devices, compared with those previously reported CPDT‐based narrow‐band‐gap polymers. Powder X‐ray diffraction (XRD) analyses suggested that these copolymers formed self‐assembled π‐π stacking and pseudobilayered structures. Under 100 mW/cm² of AM 1.5 white‐light illumination, bulk heterojunction PSC devices containing an active layer of electron donor polymers P1 – P5 mixed with electron acceptor [6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) in the weight ratio of 1:4 were investigated. The PSC device containing P1 gave the best preliminary result with an open‐circuit voltage of 0.84 V, a short‐circuit current of 2.36 mA/cm², and a fill factor of 0.38, offering an overall power conversion efficiency (PCE) of 0.77% as well as a maximal quantum efficiency of 23% from the external quantum efficiency (EQE) measurements. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2073–2092, 2009     

Synthesis and photovoltaic behaviors of narrow‐band‐gap π‐conjugated polymers composed of dialkoxybenzodithiophene‐ and thiophene‐based fused aromatic rings

π‐Conjugated polymers, PBDT‐CNETT and PBDT‐CNECPDT , were prepared by the Stille cross‐coupling polymerization. Optical and thermal properties of the obtained polymers were investigated by UV–vis spectroscopy and thermogravimetric analysis. PBDT‐CNETT and PBDT‐CNECPDT exhibited very narrow band gaps of 1.39 and 1.13 eV, respectively. Highest occupied molecular orbital energy levels estimated by surface analyzer were ?5.17 and ?5.11 eV for PBDT‐CNETT and PBDT‐CNECPDT , respectively. The solar cells based on these polymers were evaluated with the cell configuration of ITO/PEDOT‐PSS/polymer:PC₆₁BH/LiF/Al. The power conversion efficiencies of the solar cells were estimated to be 1.57 and 0.16% for PBDT‐CNETT and PBDT‐CNECPDT , respectively. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and applications of low‐bandgap conjugated polymers containing phenothiazine donor and various benzodiazole acceptors for polymer solar cells

A series of soluble donor‐acceptor conjugated polymers comprising of phenothiazine donor and various benzodiazole acceptors (i.e., benzothiadiazole, benzoselenodiazole, and benzoxadiazole) sandwiched between hexyl‐thiophene linkers were designed, synthesized, and used for the fabrication of polymer solar cells (PSC). The effects of the benzodiazole acceptors on the thermal, optical, electrochemical, and photovoltaic properties of these low‐bandgap (LBG) polymers were investigated. These LBG polymers possessed large molecular weight (M_n) in the range of 3.85?5.13 × 10⁴ with high thermal decomposition temperatures, which demonstrated broad absorption in the region of 300?750 nm with optical bandgaps of 1.80?1.93 eV. Both the HOMO energy level (?5.38 to ?5.47 eV) and LUMO energy level (?3.47 to ?3.60 eV) of the LBG polymers were within the desirable range of ideal energy level. Under 100 mW/cm² of AM 1.5 white‐light illumination, bulk heterojunction PSC devices containing an active layer of electron donor polymers mixed with electron acceptor [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) in different weight ratios were investigated. The best performance of the PSC device was obtained by using polymer PP6DHTBT as an electron donor and PC₇₁BM as an acceptor in the weight ratio of 1:4, and a power conversion efficiency value of 1.20%, an open‐circuit voltage (V_oc) value of 0.75 V, a short‐circuit current (J_sc) value of 4.60 mA/cm², and a fill factor (FF) value of 35.0% were achieved. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and characterization of donor–bridge–acceptor alternating copolymers containing perylene diimide units and their application to photovoltaic cells

We have used Suzuki coupling to prepare a series of alternating copolymers featuring coplanar cyclopentadithiophene and hole‐transporting carbazole units. We observed quenching in the photoluminescence spectra of our polymers after incorporating pendent electron‐deficient perylene diimide ( PDI ) moieties on the side chains, indicating more efficient photoinduced electron transfer. Electrochemical measurements revealed that the PDI ‐containing copolymers displayed reasonable and sufficient offsets of the energy levels of their lowest unoccupied molecular orbitals for efficient charge dissociation. The performance of bulk heterojunction photovoltaic cells incorporating the copolymer/[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester blends (1:4, w/w) was optimized when the active layer had a thickness of 70 nm. The photocurrents of the devices were enhanced as a result of the presence of the PDI moieties, thereby leading to improved power conversion efficiencies. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1298–1309, 2010     

Synthesis and applications of cyano‐vinylene‐based polymers containing cyclopentadithiophene and dithienosilole units for photovoltaic cells

Two β‐cyano‐thiophenevinylene‐based polymers containing cyclopentadithiophene ( CPDT‐CN ) and dithienosilole ( DTS‐CN ) units were synthesized via Stille coupling reaction with Pd(PPh₃)₄ as a catalyst. The effects of the bridged atoms (C and Si) and cyano‐vinylene groups on their thermal, optical, electrochemical, charge transporting, and photovoltaic properties were investigated. Both polymers possessed the highest occupied molecular orbital (HOMO) levels of about ?5.30 eV and the lowest unoccupied molecular orbital (LUMO) levels of about ?3.60 eV, and covered broad absorption ranges with narrow optical band gaps (ca. 1.6 eV). The bulk heterojunction polymer solar cell (PSC) devices containing an active layer of electron‐donor polymers ( CPDT‐CN and DTS‐CN ) blended with an electron‐acceptor, that is, [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM), in different weight ratios were explored under 100 mW/cm² of AM 1.5 white‐light illumination. The PSC device based on DTS‐CN: PC₇₁BM (1:2 w/w) exhibited a best power conversion efficiency (PCE) value of 2.25% with V_oc = 0.74 V, J_sc = 8.39 mA/cm², and FF = 0.36. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Side‐chain effects on phenothiazine‐based donor–acceptor copolymer properties in organic photovoltaic devices

A series of new phenothiazine‐based donor–acceptor copolymers, P1 and P2, were synthesized via a Suzuki coupling reaction. The weight‐averaged molecular weights (M_w) of P1 and P2 were found to be 16,700 and 16,100, with polydispersity indices of 1.74 and 1.39, respectively. The UV–visible absorption spectra of the polymer thin films contained three strong absorption bands in the ranges 318–320 nm, 430–436 nm, and 527–568 nm. The absorption peaks at 320 and 430 nm originated mainly from the phenothiazine‐based monomer units, and the longer wavelength absorption band at 527–568 nm was attributed to the increased effective conjugation length of the polymer backbones. Solution‐processed field‐effect transistors fabricated with these polymers exhibited p‐type organic thin film transistor characteristics. The field‐effect mobilities of P1 and P2 were measured to be 1.0 × 10^?4 and 7.5 × 10^?5 cm² V^?1 s^?1, respectively, with on/off ratios in the order of 10⁴ for all polymers. A photovoltaic device in which a P2/PC₇₁BM (1/3) blend film was used as the active layer exhibited an open‐circuit voltage (V_OC) of 0.70 V, a short‐circuit current (J_SC) of 6.79 mA cm⁽², a fill factor of 0.39, and a power conversion efficiency of 1.86% under AM 1.5 G (100 mW cm^?2) illumination. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of a narrow‐bandgap polymer containing alternating cyclopentadithiophene and diketo‐pyrrolo‐pyrrole units for solar cell applications

We have synthesized a narrow‐bandgap conjugated polymer ( PCTDPP ) containing alternating cyclopentadithiophene (CT) and diketo‐pyrrolo‐pyrrole (DPP) units by Suzuki coupling. This PCTDPP exhibits a low band gap of 1.31 eV and a broad absorption band from 350 to 1000 nm, which allows it to absorb more available photons from sunlight. A bulk heterojunction polymer solar cell incorporating PCTDPP and C₇₀ at a blend ratio of 1:3 exhibited a high short‐circuit current of 10.87 mA/cm² and a power conversion efficiency of 2.27%. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1669–1675, 2010     

Synthesis and characterization of donor–acceptor poly(3‐hexylthiophene) copolymers presenting 1,3,4‐oxadiazole units and their application to photovoltaic cells

We have used Grignard metathesis polymerization to prepare poly(3‐hexylthiophene)‐based copolymers containing electron‐withdrawing 4‐tert‐butylphenyl‐1,3,4‐oxadiazole‐phenyl moieties as side chains. We characterized these copolymers using ¹H and ¹³C nuclear magnetic resonance spectroscopy, thermogravimetric analysis, and gel permeation chromatography. The band gap energy of copolymer was determined from the onset of the optical absorption. The quenching effects were observed in the photoluminescence spectra of the copolymers incorporating pendant electron‐deficient 1,3,4‐oxadiazole moieties on the side chains. The photocurrents of devices were enhanced in the presence of an optimal amount of the 1,3,4‐oxadiazole moieties, thereby leading to improved power conversion efficiencies. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3331–3339, 2010     

Synthesis,characterization, and photovoltaic properties of dithienylbenzobisazole‐dithienylsilole copolymers

Three conjugated polymers comprised of dioctyl‐dithieno‐[2,3‐b:2',3'‐d]silole and a donor‐acceptor‐donor triad of either cis‐benzbisoxazole, trans‐benzobisoxazole or trans‐benzobisthiazole were synthesized via the Stille cross‐coupling reaction. The impact of varying the heteroatoms and/or the location within the benzobisazole moiety on the optical and electronic properties of the resulting polymers was evaluated via cyclic voltammetry and UV‐Visible spectroscopy. All of the polymers have similar optical band‐gaps of ～1.9 eV and highest occupied molecular orbital levels of ? 5.2 eV. However, the lowest unoccupied molecular orbitals (LUMO) ranged from ? 3.0 to ? 3.2 eV. Interestingly, when the polymers were used as donor materials in bulk‐heterojunction photovoltaic cells with PC₇₁BM as the electron‐acceptor, the benzobisoxazole‐based polymers gave slightly better results than the benzobisthiazole‐containing polymers with power conversion efficiencies up to 3.5%. These results indicate that benzobisoxazoles are promising materials for use in OPVs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1533–1540     

Low band‐gap diketopyrrolopyrrole‐containing polymers for near infrared electrochromic and photovoltaic applications

Donor–acceptor type polymers bearing diketopyrrolopyrrole and 3,4‐ethylenedioxythiophene units are reported. The polymers are green and exhibit very low band‐gaps (1.19 eV) with strong and broad absorption (maxima of about 830 nm) in the near infrared (NIR) region in their neutral film states. The polymers display color changes between dark green and light blue with exceptional optical contrasts in the NIR regions of up to 78 and 63% as thin films and single‐layer electrochromic devices, respectively. Fast switching, good stabilities as well as high coloration efficiencies (743–901 cm² C^?1) were also observed. The polymers could also be potentially used as photovoltaic material, with a power conversion efficiency of up to 1.68%. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1287–1295     

Synthesis and properties of fluorene‐based polyheteroarylenes for photovoltaic devices

Novel copolymers consisting of the alternating push–pull comonomers fluorene and thieno[3,4‐b]pyrazine/quinoxaline were synthesized by a palladium‐catalyzed Suzuki cross‐coupling reaction in 60–80% yields. The structure of the deeply colored copolymers was confirmed with ¹H and ¹³C NMR. All the new materials were characterized with spectroscopic and electrochemical methods. Bulk heterojunction organic solar cells based on some of the novel polymers in combination with the well‐known fullerene acceptor [6,6]‐phenyl C₆₁–butyric acid methyl ester were fabricated, and their photovoltaic parameters were measured. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6952–6961, 2006     

Toward low‐band gap dithienophosphole copolymers for an application in organic solar cells

Two functionalized dithieno[3,2‐b:2′,3′‐d]phospholes with solubilizing groups have been synthesized that allow for the generation of a series of π‐conjugated AB‐ and ABC‐copolymers. The polymers obtained show notable optoelectronic properties with red‐shifted absorption and emission in the orange to red section of the optical solar spectrum. Although combination of dithienophosphole units with fluorene building blocks gives access to processable polymers with band gaps between 2.2 and 2.3 eV in solution and 2.0 eV in the solid state, an ABC copolymer based on dithienophosphole, fluorene, and bis(thienyl)benzothiadiazole units was found to not only exhibit a suitable band gap for solar cell applications (solution: 2.0 eV; solid state: 1.7 eV) but also showed good solubility as well as good electron transfer properties in the presence of fullerene (C₆₀). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8179–8190, 2008     

Design and synthesis of dithieno[3,2‐b:2′3′‐d]pyrrole‐based conjugated polymers for photovoltaic applications: consensus between low bandgap and low HOMO energy level

A strategy of the fine‐tuning of the degree of intrachain charge transfer and aromaticity of polymer backbone was adopted to design and synthesize new polymers applicable in photovoltaics. Three conjugated polymers P1 , P2 , and P3 were synthesized by alternating the electron‐donating dithieno[3,2‐b:2′3′‐d]pyrrole (D) and three different electron‐accepting (A) segments ( P1 : N‐(2‐ethylhexyl)phthalimide; P2 : 1,4‐diketo‐3,6‐diphenylpyrrolo[3,4‐c]pyrrole; and P3 : thiophene‐3‐hexyl formate) in the polymer main chain. Among the three polymers, P2 possessed the broadest absorption band ranging from 300 to 760 nm, the lowest bandgap (1.63 eV), and enough low HOMO energy level (?5.27 eV) because of the strong intrachain charge transfer from D to A units and the appropriate extent of quinoid state in the main chain of P2 , which was convinced by the theoretical simulation of molecular geometry and front orbits. Photovoltaic study of solar cells based on the blends of P1 – P3 and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) demonstrated that P2 :PCBM exhibited the best performance: a power conversion efficiency of 1.22% with a high open‐circuit voltage (V_OC) of 0.70 V and a large short‐circuit current (I_SC) of 5.02 mA/cm² were achieved. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of fluorene‐based low‐band gap copolymers containing propylenedioxythiophene and benzothiadiazole derivatives for bulk heterojunction photovoltaic cell applications

The following noble series of soluble π‐conjugated statistical copolymers was synthesized by palladium catalyzed Suzuki polymerization: poly[(9,9‐dioctylfluorene)‐alt‐(4,7‐bis(3′,3′‐dihepyl‐3,4‐propylenedioxythienyl)‐2,1,3‐benzothiadiazole)] (PFO‐PTBT) derived from poly(9,9‐dioctylfluorene) (PFO) and poly[(4,7‐bis(3′,3′‐dihepyl‐3,4‐propylenedioxythienyl)‐2,1,3‐benzothiadiazole)] poly(heptyl₄‐PTBT). The structure and properties of these polymers were characterized using ¹H‐, ¹³C‐NMR, UV–visible spectroscopy, elemental analysis, GPC, DSC, TGA, photoluminescence (PL), and cyclic voltammetry (CV). The statistical copolymers, PFO‐PTBT (9:1, 8.4:1.6, 6.5:3.5), were soluble in common organic solvents and easily spin coated onto indium‐tin oxide (ITO) coated glass substrates. The weight‐average molecular weight (M_w) and polydispersity of the PFO‐PTBT ranged from (1.0–4.2) × 10⁴ and 1.5–2.3, respectively. Bulk heterojunction photovoltaic cells with an ITO/PEDOT/PFO‐PTBT:PCBM/LiF/Al configuration were fabricated, and the devices using PFOPTBT (6.5:3.5) showed the best performance compared with those using PFO‐PTBT (9:1, 8.4:1.6). A maximum power conversion efficiency (PCE) of 0.50% (V_oc = 0.66 V, FF = 0.29) was achieved with PFO‐PTBT (6.5:3.5). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6175–6184, 2008     

Benzodifuran‐containing well‐defined π‐conjugated polymers for photovoltaic cells

Two well‐defined alternating π‐conjugated polymers containing a soluble electroactive benzo[1,2‐b:4,5‐b′]difuran (BDF) chromophore, poly(BDF‐(9‐phenylcarbazole)) (PBDFC), and poly(BDF‐benzothiadiazole) (PBDFBTD) were synthesized via Sonogashira copolymerizations. Their optical, electrochemical, and field‐effect charge transport properties were characterized and compared with those of the corresponding homopolymer PBDF and random copolymers of the same overall composition. All these polymers cover broad optical absorption ranges from 250 to 750 nm with narrow optical band gaps of 1.78–2.35 eV. Both PBDF and PBDFBTD show ambipolar redox properties with HOMO levels of ?5.38 and ?5.09 eV, respectively. The field‐effect mobility of holes varies from 2.9 × 10^?8 cm² V^?1 s^?1 in PBDF to 1.0 × 10^?5 cm² V^?1 s^?1 in PBDFBTD. Bulk heterojunction solar cell devices were fabricated using the polymers as the electron donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as the electron acceptor, leading to power conversion efficiencies of 0.24–0.57% under air mass 1.5 illumination (100 mW cm^?2). These results indicate that their band gaps, molecular electronic energy levels, charge mobilities, and molecular weights are readily tuned by copolymerizing the BDF core with different π‐conjugated units. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and photovoltaic properties of 2,6‐bis(2‐thienyl) benzobisazole and 4,8‐bis(thienyl)‐benzo[1,2‐B:4,5‐B′]dithiophene copolymers

In an effort to design efficient low‐cost polymers for use in organic photovoltaic cells the easily prepared donor–acceptor–donor triad of a either cis‐benzobisoxazole, trans‐benzobisoxazole or trans‐benzobisthiazole flanked by two thiophene rings was combined with the electron‐rich 4,8‐bis(5‐(2‐ethylhexyl)‐thien‐2‐yl)‐benzo[1,2‐b:4,5‐b′]dithiophene. The electrochemical, optical, morphological, charge transport, and photovoltaic properties of the resulting terpolymers were investigated. Although the polymers differed in the arrangement and/or nature of the chalcogens, they all had similar highest occupied molecular orbital energy levels (?5.2 to ?5.3 eV) and optical band gaps (2.1–2.2 eV). However, the lowest unoccupied molecular orbital energy levels ranged from ?3.1 to ?3.5 eV. When the polymers were used as electron donors in bulk heterojunction photovoltaic devices with PC₇₁BM ([6,6]‐phenyl C₇₁‐butyric acid methyl ester) as the acceptor, the trans‐benzobisoxazole polymer had the best performance with a power conversion efficiency of 2.8%. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 316–324     

New moderate bandgap polymers containing alkoxysubstituted‐benzo[c][1,2,5]thiadiazole and thiophene‐based units

Alkoxysubstituted benzo[c][1,2,5]thiadiazole electron accepting units were prepared and copolymerized with various thiophene‐based electron donating monomers to produce new low bandgap polymers P1–4 . The materials showed broad absorption in the range from 300 to 700 nm with bandgaps below 2 eV in solution. Efficiencies of over 1% were obtained from photovoltaic cells using P4 with PCBM as acceptor. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

New thiophene‐phenylene‐thiophene acceptor random conjugated copolymers for optoelectronic applications

New low band gap thiophene‐phenylene‐thiophene ( TPT )‐based donor‐acceptor‐donor random copolymers were synthesized for optoelectronic device applications by a palladium‐catalyzed Stille coupling reaction under microwave heating. The acceptors included 2,3‐bis(4‐(2‐ethylhexyloxy)phenyl)‐5,8‐bis[5′‐bromo‐dithien‐2‐yl‐quinoxalines] ( DTQ ) and 3,6‐bis(5‐bromothiophen‐2‐yl)‐2,5‐bis(2‐ethyl‐hexyl)‐pyrrolo[3,4‐c]‐pyrrole‐1,4‐dione ( DPP ). The prepared random copolymers were named as PTPTDTQ_0.55 , PTPTDTQ_0.34DPP_0.14 , and PTPTDTQ_0.26DPP_0.34 depending on the copolymer ratio. The optical band gaps (E) of PTPTDTQ_0.55 , PTPTDTQ_0.34DPP_0.14 , and PTPTDTQ_0.26DPP_0.34 were 1.74, 1.56, and 1.48 eV, respectively. The hole mobility obtained from the field‐effect transistor devices prepared from PTPTDTQ_0.55 , PTPTDTQ_0.34DPP_0.14 , and PTPTDTQ_0.26DPP_0.34 were 2.2 × 10^?3, 2.4 × 10^?3, and 4.7 × 10^?3 cm² V^?1 s^?1, respectively, with the on‐off ratios of 4.0 × 10⁴, 4.0 × 10⁴, and 5.3 × 10⁴. It suggested that the significant intramolecular charge transfer between the TPT and acceptor led to the band gap reduction and hole mobility enhancement. Polymer solar cells of these TPT ‐based copolymers blended with 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl‐[6,6]‐C‐71 (PC₇₁BM) under illumination of AM 1.5G (100 mW cm^?2) solar simulator exhibited a power conversion efficiency (PCE) as high as 3.71%. Besides, the near‐infrared photodetector device prepared from PTPTDTQ_0.26DPP_0.34 showed a high external quantum efficiency exceeding 32% at 700 nm (under ?3 V bias) and fast‐speed response. This study suggests that the prepared TPT ‐based donor‐acceptor random copolymers exhibited promising and versatile applications on optoelectronic devices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2351–2360, 2010     

Effect of branched alkyl side chains on the performance of thin‐film transistors and photovoltaic cells fabricated with isoindigo‐based conjugated polymers

New isoindigo and di(thienyl)ethylene‐containing π‐extended conjugated polymers with different branched side chains were synthesized to investigate their physical properties and device performance in thin‐film transistors and photovoltaic cells. 11‐Butyltricosane (S3) and 11‐heptyltricosane (S6) groups were used as side‐chain moieties tethered to isoindigo units. The linking groups between the polymer backbone and bifurcation point in the branched side chain differ in the two polymers (i.e., PIDTE‐S3 and PIDTE‐S6 ). The polymers bearing S6 side chains showed much better charge transport behavior than those with S3 side chains. Thermally annealed PIDTE‐S6 film exhibited an outstanding hole mobility of 4.07 cm² V^?1 s^?1 under ambient conditions. Furthermore, bulk heterojunction organic photovoltaic cells made from a blend film of PIDTE‐S3 and (6,6)‐phenyl C61‐butyric acid methyl ester demonstrated promising device performance with a power conversion efficiency in the range of 4.9–5.0%. © 2015 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 2015 , 53, 1226–1234     

Bandgap engineering of indenofluorene‐based conjugated copolymers with pendant donor‐π‐acceptor chromophores for photovoltaic applications

Three narrow‐band‐gap conjugated copolymers based on indenofluorene and triphenylamine with pendant donor‐π‐acceptor chromophores were successfully synthesized by post‐functionalization approach. All the polymers have good solubility in common solvents and excellent thermal stability. The photophysical properties, energy levels and band gaps of the polymers were well manipulated by introducing different acceptor groups onto the end of their conjugated side chains. By using different acceptor groups, the band gaps of the polymers were narrowed from 1.86 to 1.53 eV by lowering their lowest unoccupied molecular orbital levels, whereas their relatively deep highest occupied molecular orbital levels of approximately ?5.35 eV were maintained. Bulk‐heterojunction solar cells with these polymers as electron donors and (6,6)‐phenyl‐C₇₁‐butyric acid methyl ester as acceptor showed power conversion efficiencies as high as 3.1% and high open circuit voltages more than 0.88 eV. The relationships between the performance and film morphology, energy levels, charge mobilities were discussed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011