Synthesis of poly(vinyl ether)‐based,ABA triblock‐type thermoplastic elastomers with functionalized soft segments and their gas permeability

The ABA‐type triblock copolymers consisting of poly(2‐adamantyl vinyl ether) [poly(2‐AdVE)] as outer hard segments and poly(6‐acetoxyhexyl vinyl ether) [poly(AcHVE)], poly(6‐hydroxyhexyl vinyl ether) [poly(HHVE)], or poly(2‐(2‐methoxyethoxy)ethyl vinyl ether) [poly(MOEOVE)] as inner soft segments were synthesized by sequential living cationic polymerization. Despite the presence of polar functional groups such as ester, hydroxyl, and oxyethylene units in their soft segments, the block copolymers formed elastomeric films. The thermal and mechanical properties and morphology of the block copolymers showed that the two polymer segments of these triblock copolymers were segregated into microphase‐separated structure. Effect of the functional groups in the soft segments on gas permeability was investigated as one of the characteristics of the new functional thermoplastic elastomers composed solely of poly(vinyl ether) backbones. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1114–1124     

PIB‐based polyurethanes. IV. The morphology of polyurethanes containing soft co‐segments*

Novel polyurethanes consisting of polyisobutylene (PIB)/poly(tetramethylene oxide) (PTMO) or PIB/poly(hexamethylene carbonate) (PC) soft co‐segments in combination with 4,4′‐methylene‐bis(cyclohexyl isocyanate)/1,6‐hexanediol, 1,4‐butanediol, or 1,6‐hexamethylene diamine hard segments exhibit excellent mechanical properties (upto 31 MPa tensile strength with 700% elongation) together with unprecedented oxidative/hydrolytic stability. A structural model of the morphology of these polyurethanes was developed that reflects this combination of properties. The key new elements of our model are H bridges between the PTMO and PC type soft and urethane hard segments, which compatibilize the soft and hard domains, and the presence of large quantities of chemically resistant PIB soft segments that protect the other oxidatively/hydrolytically vulnerable constituents. A variety of FTIR, DSC, SAXS, AFM, and DMTA experiments strongly support the proposed morphological model. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6180–6190, 2009     

Biobased polyurethanes from polyether polyols obtained by ionic‐coordinative polymerization of epoxidized methyl oleate

A series of poly(ether urethane) networks were synthesized from polyether polyols obtained by ionic‐coordinative polymerization of epoxidized methyl oleate (EMO) using 4,4′‐methylenebis(phenyl isocyanate) or l ‐lysine diisocyanate as coupling agents. Moreover, a variety of segmented poly(ether urethane) networks with different hard segment contents were obtained using 1,3‐propanediol as the chain extender. The materials were characterized by differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical thermal analysis, and tensile properties. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Chain‐growth limiting reactions in the cationic polymerization of 3‐ethyl‐3‐hydroxymethyloxetane

3‐Ethyl‐3‐hydroxymethyloxetane (EOX) polymerizes readily to branched multihydroxyl polyethers. Molecular weights of the polymers are, however, limited, and macromolecules are predominantly cyclic. This indicates that intramolecular chain transfer to polymer (back‐biting) proceeds in the system. Repeating units in poly‐EOX contain two nucleophilic sites that may participate in back‐biting, namely ether groups and hydroxyl groups. Analysis of matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) mass spectra of poly‐EOX prepared in the presence of analogous polyether that does not contain HO? groups (poly(3,3‐dimethyloxetane)‐poly‐DMOX) shows that the ether group in the repeating unit of poly‐DMOX does not participate in chain transfer to the polymer. However, when DMOX was polymerized in the presence of poly‐EOX, clear evidence of participation of HO? groups in intramolecular chain transfer was obtained. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 245–252, 2004     

Crystallization‐induced aging in poly(trimethylene terephthalate)/ poly(ethylene oxide terephthalate) segmented block copolymers

A new type poly(ether–ester) based on poly(trimethylene terephthalate) as rigid segments and poly(ethylene oxide terephthalate) as soft segments was synthesized and its aging behavior were investigated. Different from other polymer, the segmented block copolymers exhibited a unique aging mechanism. That is, the degradation of mechanical property within short term annealing was due to the overgrown crystals and dramatically increased crystallinity, which was proved by field emission scanning electron microscope (FE‐SEM) and differential scanning calorimetry (DSC), respectively. The deterioration in mechanical property after long term annealing was the results of both the increase in crystallinity and the decrease in molecular weight. Moreover, FE‐SEM showed many interesting flower‐like crystals presented on the surface of annealed sample. The flower‐like crystals consist of several radialized petal‐like arms and a more densely packed center, which has been seldom found in polymer bulk. Wide‐angle x‐ray diffraction results showed that the copolymer has the same crystal structure as PTT. Such poly(ether–ester) or its blends with other polymer could be suitable for rapid degradable products, such as package and vessel. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 411–416, 2010     

Synthesis and characterization of soluble polyimides derived from 2,2′‐Bis(3,4‐dicarboxyphenoxy)‐9,9′‐spirobifluorene dianhydride

The synthesis of aromatic poly(ether imide)s containing spirobifluorene units in the polymer backbone is described. 2,2′‐Bis(3,4‐dicarboxyphenoxy)‐9,9′‐spirobifluorene dianhydride, which was used as a new monomer, was synthesized with 2,2′‐dihydroxy‐9,9′‐spirobifluorene as the starting material. In the spiro‐segment, the rings of the connected bifluorene were orthogonally arranged. This bis(ether anhydride) monomer was employed in reactions with a variety of aromatic diamines to furnish poly(ether imide)s, involving an initial ring‐opening polycondensation and subsequent chemically induced cyclodehydration. Excellent solubility in common organic solvents at room temperature, good optical transparency, and high thermal stability are the prominent characteristic features of these new polymers, which can be attributed to the presence of spiro‐fused orthogonal bifluorene segments along the polymer chain. The glass‐transition temperatures of the polyimides were 240–293 °C, and the 5% weight‐loss temperatures were greater than 500 °C. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 262–268, 2002     

Solid polymer electrolytes. IV. Preparation and characterization of novel crosslinked epoxy‐siloxane polymer complexes as polymer electrolytes

Two series of novel crosslinked siloxane‐based polymers and their complexes with lithium perchlorate (LiClO₄) were prepared and characterized by Fourier transform infrared spectroscopy, solid‐state NMR (¹³C, ²⁹Si, and ⁷Li nuclei), and differential scanning calorimetry. Their thermal stability and ionic conductivity of these complexes were also investigated by thermogravimetric and AC impedance measurements. In these polymer networks, poly(propylene oxide) chains with different molecular weights were introduced through self‐synthesized epoxy‐siloxane precursors cured with two curing agents. The glass‐transition temperature (T_g) of these copolymers is dependent on the length of the ether units. The dissolution of LiClO₄ considerably increases the T_g of the polyether segments. The dependence of the ionic conductivity was investigated as a function of temperature, LiClO₄ concentration, and the molecular weight of the polyether segments. The ion‐transport behavior was affected by the combination of the ionic mobility and number of carrier ions. The ⁷Li solid‐state NMR line shapes of these polymer complexes suggest a significant interaction between Li⁺ ions and the polymer matrix, and temperature‐ and LiClO₄ concentration‐dependent chemical shifts are correlated with ionic conductivity. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1226–1235, 2002     

A solution‐processible poly(p‐phenylene vinylene) without alkyl substitution: Introducing the cis‐vinylene segments in polymer chain for improved solubility,blue emission,and high efficiency

A soluble all‐aromatic poly(2,5‐diphenyl‐1,4‐phenylenevinylene) (2,5‐DP‐PPV) is synthesized by utilizing aromatic phosphonium and aldehyde monomers through Wittig reaction. The H¹ NMR and FTIR measurements indicate that over 50% content of cis‐vinylene units exist in polymer backbone. The diphenyl‐substituted benzaldehyde monomer plays an important role to enhance cis‐products (Z‐selectivity) in Wittig reactions. The twisted cis‐segments in polymer backbone reduce the interchain interactions and enhance the solubility of such all‐aromatic PPV derivative in common organic solvents. 2,5‐DP‐PPV exhibits good solubility in common organic solvents, such as tetrahydrofuran and chloroform. The polymer film exhibits a blue light emission (λ_max = 485 nm) and a very high photoluminescence efficiency of 78%. The cis‐trans photo isomerization of this polymer in solution and the impact on the optical properties are also investigated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5242–5250, 2008     

New segmented poly(ester‐urethane)s from renewable resources

The physical and mechanical properties of aliphatic homopolyesters from monomers obtainable from renewable resources, namely, 1,3‐propanediol and succinic acid, were improved by their combination with aromatic urethane segments capable of establishing strong intermolecular hydrogen bonds. Segmented poly(ester‐urethane)s were synthesized from dihydroxy‐terminated oligo(propylene succinate)s chain‐extended with 4,4′‐diisophenylmethane diisocyanate. The newly synthesized materials were exhaustively characterized by ¹H NMR spectroscopy, size exclusion chromatography, differential scanning calorimetry, dynamic mechanical analysis, and with respect to their main static mechanical properties, an Instron apparatus was used. The average repeat number of the hard segments, evaluated by NMR, ranged from 4 to 9, whereas that of the flexible segments was about 14. The degree of crystallinity, glass‐transition temperature, melting point, tensile strength, elongation, and Young's modulus were influenced by the ratio between hard and soft segments of the segmented copolymer in a predictable way. The results demonstrated that poly(ester‐urethane)s from 1,3‐propanediol and succinic acid are promising thermoplastics. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 630–639, 2001     

Novel silver/polyurethane nanocomposite by in situ reduction: Effects of the silver nanoparticles on phase and viscoelastic behavior

A novel silver/poly(carbonate urethane) nanocomposite was prepared through in situ reduction of a silver salt (AgNO₃) added to a solution consisting of a commercial poly(carbonate urethane) dissolved in N,N‐dimethylformamide (DMF). In this system, the presence of the poly(carbonate urethane) was proved to protect the silver nanoparticles, whose formation was confirmed by means of UV–vis spectroscopy, from aggregation phenomena. The silver morphology developed in the solid state after DMF casting was imaged by FESEM. Homogeneous dispersion of silver nanoprisms in the poly(carbonate urethane) matrix was clearly observed. The effects of dispersion of silver nanoparticles within the poly(carbonate urethane) matrix were investigated by means of ATR‐FTIR and multifrequency dynamic mechanical thermal analyses. The obtained results revealed that the presence of silver nanoparticles modifies both the phase and the viscoelastic behaviors of poly(carbonate urethane). As a matter of fact, the hydrogen bond formation in the hard and soft segments was found to be hindered and the molecular motions of the soft segments were restricted, because a comparatively higher activation energy was required for the related α‐relaxation process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 344–350, 2008     

Calorimetric and Dielectric Study of the Segmented Biodegradable Poly(ester‐urethane)s Based on Bacterial Poly[(R)‐3‐hydroxybutyrate]

Two series of segmented poly(ester‐urethane)s were synthesized from bacterial poly[(R)‐3‐hydroxybutyrate]‐diol (PHB‐diol), as hard segments, and either poly(ε‐caprolactone)‐diol (PCL‐diol) or poly(butylene adipate)‐diol (PBA‐diol), as soft segments, using 1,6‐hexamethylene diisocyanate as a chain extender. The hard‐segment content varied from 0 to 50 wt.‐%. These materials were characterized using ¹H NMR spectroscopy and GPC. The polymers obtained were investigated calorimetrically and dielectrically. DSC showed that the T_g of either the PCL or PBA soft segments are shifted to higher temperatures with increasing PHB hard‐segment content, revealing that either the PCL or PBA are mixed with small amounts of PHB in the amorphous domains. The results also showed that the crystallization of soft or hard segments was physically constrained by the microstructure of the other crystalline phase, which results in a decrease in the degree of crystallinity of either the soft or hard segments upon increase of the other component. The dielectric spectra of poly(ester‐urethane)s, based on PCL and PHB, showed two primary relaxation processes, designated as α_S and α_H, which correspond to glass–rubber transitions of PCL soft and PHB hard segments, respectively. Whereas in the case of other poly(ester‐urethane)s, derived from PBA and PHB, only one relaxation process was observed, which broadens and shifts to higher temperature with increasing PHB hard‐segment content. It was concluded from these results that our investigated materials exhibit micro‐phase separation of the hard and soft segments in the amorphous domains.     

Synthesis and characterization of block poly(ester‐ether‐urethane)s from bacterial poly(3‐hydroxybutyrate) oligomers

Telechelic hydroxylated poly(3‐hydroxybutyrate) (PHB‐diol) oligomers have been successfully synthesized in 90–95% yield from high molar mass PHB by tin‐catalyzed alcoholysis with different diols (mainly 1,4‐butanediol) in diglyme. The PHB‐diol oligomers structure was studied by nuclear magnetic resonance, Fourier transformed infrared spectroscopy MALDI‐ToF MS, and size exclusion chromatography, whereas their crystalline structures, thermal properties and thermal stability were analyzed by wide angle X‐ray scattering, DSC, and thermogravimetric analyses. The kinetic of the alcoholysis was studied and the influence of (i) the catalyst amount, (ii) the diol amount, (iii) the reaction temperature, and (iv) the diol chain length on the molar mass was discussed. The influence of the PHB‐diol molar mass on the thermal stability, the thermal properties and optical properties was investigated. Then, tin‐catalyzed poly(ester‐ether‐urethane)s (PEEU) of M_n = 15,000–20,000 g/mol were synthesized in 1,2‐dichloroethane from PHB‐diol oligomers (P_ester) with modified 4,4'‐MDI and different polyether‐diols (P_ether) (PEG‐2000, PEG‐4000, and PPG‐PEG‐PPG). The influence of the PHB‐diol chain length, the P_ether/P_ester ratio, the polyether segment nature and the PEG chain length on the thermal properties and crystalline structures of PEEUs was particularly discussed. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1949–1961     

Polyisobutylene‐based polyurethanes. V. Oxidative‐hydrolytic stability and biocompatibility

The oxidative/hydrolytic stability of polyurethanes (PUs) containing exclusively polyisobutylene (PIB), or mixed PIB/polytetramethylene oxide (PTMO), or mixed PIB/polyhexamethylene carbonate (PC) soft segments was investigated. The tensile strengths and elongations of various PUs were determined before and after agitating in 35% HNO₃ or 20% H₂O₂/0.1 M CoCl₂ solutions and retentions were quantified. The presence of PIB imparts significant oxidative/hydrolytic resistance. The tensile strength and elongation of PUs containing 70% PIB, or those of mixed PIB/PC soft segments with 50% PIB, remained essentially unchanged upon exposure to HNO₃; in contrast, PUs containing mixed PIB/PTMO soft segments with 50% PIB underwent significant degradation. The tensile strength of PUs with mixed PIB/PC (60/10%) soft segment increased after exposure to HNO₃, most likely because of oxidative crosslinking of PC segments. PIB/PTMO‐ and PIB/PC‐based PUs and commercially available PUs (Elast‐Eon® and Carbothane®) were exposed to H₂O₂/CoCl₂ solutions for up to 14 weeks. Although the experimental PIB/PC‐based PUs exhibited negligible change in mechanical properties and no surface damage, Elast‐Eon® and Carbothane® showed significant surface damage. PIB‐based polyureas and Bionate® were implanted in rats for 4 weeks in vivo, and their biocompatibility was investigated. The biocompatibility of PIB‐based materials was superior to Bionate®. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2194–2203, 2010     

Synthesis of ABA‐triblock and star‐diblock copolymers with poly(2‐adamantyl vinyl ether) and poly(n‐butyl vinyl ether) segments: New thermoplastic elastomers composed solely of poly(vinyl ether) backbones

ABA‐type triblock copolymers and AB‐type star diblock copolymers with poly(2‐adamantyl vinyl ether) [poly(2‐AdVE)] hard outer segments and poly(n‐butyl vinyl ether) [poly(NBVE)] soft inner segments were synthesized by sequential living cationic copolymerization. Although both the two polymer segments were composed solely of poly(vinyl ether) backbones and hydrocarbon side chains, they were segregated into microphase‐separated structure, so that the block copolymers formed thermoplastic elastomers. Both the ABA‐type triblock copolymers and the AB‐type star diblock copolymers exhibited rubber elasticity over wide temperature range. For example, the ABA‐type triblock copolymers showed rubber elasticity from about ?53 °C to about 165 °C and the AB‐type star diblock copolymer did from about ?47 °C to 183 °C with a similar composition of poly(2‐AdVE) and poly(NBVE) segments in the dynamic mechanical analysis. The AB‐type star diblock copolymers exhibited higher tensile strength and elongation at break than the ABA‐type triblock copolymers. The thermal decomposition temperatures of both the block copolymers were as high as 321–331 °C, indicating their high thermal stability. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Poly(caprolactone) containing highly branched segmented poly(ester urethane)s via A2 with oligomeric B3 polymerization

Highly branched, poly(caprolactone) (PCL) containing segmented poly(ester urethane)s were synthesized via polymerization of A₂ and oligomeric B₃ type monomers. An isocyanate functional butanediol‐based A₂ hard segment was synthesized and immediately reacted with a poly(caprolactone)‐based trifunctional (B₃) soft segment. Characterization of thermal properties using DMA and DSC analysis demonstrated that the PCL segment remained amorphous in branched poly(ester urethane)s. Conversely, the crystallinity of PCL segment was retained to some extent in a linear analogue with equivalent soft segment molecular weight. Tensile testing revealed a slight decrease in Young's modulus and tensile strength for the highly branched polymers compared with a linear analogue. However, highly branched poly(ester urethane)s demonstrated lower hysteresis. In addition to synthesis of highly branched polymers, poly(ester urethane) networks were synthesized from a highly branched hydroxyl‐terminated precursor and a low molar mass diisocyanate as the crosslinking agent. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6285–6295, 2008     

Structural and end‐group effects on bulk and surface properties of hyperbranched poly(urea urethane)s

The hydroxy end groups of aromatic and aliphatic hyperbranched poly‐(urea urethane)s prepared with an AA* + B*B₂ one‐pot method were modified with phenylisocyanate, butylisocyanate, and stearylisocyanate. The success of the modification reaction was verified with ¹H NMR and IR spectroscopy. Linear model poly‐(urea urethane)s were prepared, too, for comparison. The bulk properties of OH functionalized hyperbranched poly(urea urethane)s, compared with those of linear analogues and modified hyperbranched poly(urea urethane)s, were studied with differential scanning calorimetry, thermogravimetric analysis, and temperature‐dependent Fourier transform infrared measurements. Transparent and smooth thin films could be prepared from all polymer samples and were examined with a light microscope, a microglider, and an atomic force microscope. The properties of the polymer surface were examined by measurements of the contact angle and zeta potential. For all samples, the properties were mainly governed by the strong interactions of the urea and urethane units within the backbone, whereas the influence of the nature of the end groups and of the branched structure was reduced in comparison with other hyperbranched polymer systems. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3376–3393, 2005     

Synthesis and properties of multiblock copolymers consisting of poly(L‐lactic acid) and poly(oxypropylene‐ co‐oxyethylene) prepared by direct polycondensation

A multiblock copoly(ester–ether) consisting of poly(l ‐lactic acid) (PLLA) and poly(oxypropylene‐co‐oxyethylene) (PN) was prepared and characterized. Preparation was done via the solution polycondensation of a thermal oligocondensate of l ‐lactic acid, a commercially available telechelic polyether (PN: Pluronic‐F68), and dodecanedioic acid as a carboxyl/hydroxyl adjusting agent. When stannous oxide was used as the catalyst, the molecular weight of the resultant PLLA/PN block copolymers became very high (even with a high PN content) under optimized reaction conditions. The refluxing of diphenyl ether (solvent) at reduced pressure allowed the efficient removal of the condensed water from the reaction system and the feed‐back of the intermediately formed l ‐lactide at the same time in order to successfully bring about a high degree of condensation. The copolymer films obtained by solution casting became more flexible with the increasing PN content as soft segments. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1513–1521, 1999     

Three‐arm star block copolymers of aromatic polyether and polystyrene from chain‐growth condensation polymerization,atom transfer radical polymerization,and click reaction

Well‐defined (AB)₃ type star block copolymer consisting of aromatic polyether arms as the A segment and polystyrene (PSt) arms as the B segment was prepared using atom transfer radical polymerization (ATRP), chain‐growth condensation polymerization (CGCP), and click reaction. ATRP of styrene was carried out in the presence of 2,4,6‐tris(bromomethyl)mesitylene as a trifunctional initiator, and then the terminal bromines of the polymer were transformed to azide groups with NaN₃. The azide groups were converted to 4‐fluorobenzophenone moieties as CGCP initiator units by click reaction. However, when CGCP was attempted, a small amount of unreacted initiator units remained. Therefore, the azide‐terminated PSt was then used for click reaction with alkyne‐terminated aromatic polyether, obtained by CGCP with an initiator bearing an acetylene unit. Excess alkyne‐terminated aromatic polyether was removed from the crude product by means of preparative high performance liquid chromatography (HPLC) to yield the (AB)₃ type star block copolymer (M_n = 9910, M_w/M_n = 1.10). This star block copolymer, which contains aromatic polyether segments with low solubility in the shell unit, exhibited lower solubility than A₂B or AB₂ type miktoarm star copolymers. In addition, the obtained star block copolymer self‐assembled to form spherical aggregates in solution and plate‐like structures in film. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermal degradation mechanism of poly(arylene sulfone)s by stepwise Py‐GC/MS

The thermal degradation of poly(ether sulfone) (PES) and polysulfone (PSF) was studied with a combination of thermogravimetric analysis and stepwise pyrolysis–gas chromatography/mass spectrometry techniques with consecutive heating of the samples at fixed temperature intervals (100 °C) to achieve narrow‐temperature pyrolysis conditions. The individual mass chromatograms of various pyrolysates were correlated with pyrolysis temperatures to elucidate the pyrolysis mechanism. The major mechanism for both PES and PSF was a one‐stage pyrolysis involving main‐chain random scission and carbonization. The major products SO₂ and phenol were released from the sulfone and ether groups in PES. The major products SO₂, phenol, and 1‐methyl‐4‐phenoxybenzene were released from the sulfone, ether, and isopropylene groups in PSF. In the PES, the thermal stability of the sulfone and ether groups was identical to the maximum thermogravimetric loss rate. In the PSF, the thermal stability was in the following order: sulfone < ether < isopropylene. The temperature of the maximum thermogravimetric loss rate was similar to the maximum evolution of phenol. However, there was a considerable difference in the thermal behavior of both polymers; the correlation of the polymer structure to the degradation mechanism is discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 583–593, 2000     

Spontaneous crosslinking of poly(1,5‐dioxepan‐2‐one) originating from ether bond fragmentation

The spontaneous reaction of unsaturated double bonds induced by the fragmentation of ether bonds is presented as a method to obtain a crosslinked polymer material. Poly(1,5‐dioxepan‐2‐one) (PDXO) was synthesized using three different polymerization techniques to investigate the influence of the synthesis conditions on the ether bond fragmentation. It was found that thermal fragmentation of the ether bonds in the polymer main chain occurred when the synthesis temperature was 140 °C or higher. The double bonds produced reacted spontaneously to form crosslinks between the polymer chains. The formation of a network structure was confirmed by Fourier transform infrared spectrometry and differential scanning calorimetry. In addition, the low molar mass species released during hydrolysis of the DXO polymers were monitored by ESI‐MS and MALDI‐TOF‐MS. Ether bond fragmentation also occurred during the ionization in the electrospray instrument, but predominantly in the lower mass region. No fragmentation took place during MALDI ionization, but it was possible to detect water‐soluble DXO oligomers with a molar mass up to approximately 5000 g/mol. The results show that ether bond fragmentation can be used to form a network structure of PDXO. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7258–7267, 2008