Decoupling crystalline volume fraction and VOC in microcrystalline silicon pin solar cells by using a µc‐Si:F:H intrinsic layer

Microcrystalline silicon thin film pin solar cells with a highly crystallized intrinsic μc‐Si:F:H absorber were prepared by RF‐plasma enhanced chemical vapour deposition using SiF₄ as the gas precursor. The cells were produced with a vacuum break between the doped layer and intrinsic layer depositions, and the effect of different subsequent interface treatment processes was studied. The use of an intrinsic μc‐Si:H p/i buffer layer before the first air break increased the short circuit current density from 22.3 mA/cm² to 24.7 mA/cm². However, the use of a hydrogen‐plasma treatment after both air breaks without an interface buffer layer improved both the open circuit voltage and the fill factor. Although the material used for the absorber layer showed a very high crystalline fraction and thus an increased spectral response at long wavelengths, an open‐circuit voltage (V_OC) of 0.523 V was nevertheless observed. Such a value of V_OC is higher than is typically obtained in devices that employ a highly crystallized absorber as reported in the literature (see abstract figure). Using a hydrogen‐plasma treatment, a single junction μc‐Si:F:H pin solar cell with an efficiency of 8.3% was achieved.

     

Microcrystalline silicon‐carbon alloys as anti‐reflection window layers in high efficiency thin film silicon solar cells

Microcrystalline silicon‐carbide (μc‐SiC:H) films were prepared using hot wire chemical vapor deposition at low substrate temperature. The μc‐SiC:H films were employed as window layers in microcrystalline silicon (μc‐Si:H) solar cells. The short‐circuit current density (J_SC) in these n‐side illuminated n–i–p cells increases with increasing the deposition time t_W of the μc‐SiC:H window layer from 5 min to 60 min. The enhanced J_SC is attributed to both the high transparency and an anti‐reflection effect of the μc‐SiC:H window layer. Using these favourable optical properties of the μc‐SiC:H window layer in μc‐Si:H solar cells, a J_SC value of 23.8 mA/cm² and cell efficiencies above 8.0% were achieved with an absorber layer thickness of 1 μm and a Ag back reflector. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Nanocystalline silicon solar cells

Nanocrystalline silicon material has made rapid progress in the last several years and at present it can be defined as real device quality as a photoactive layer for solar cells. A number of innovative ideas, such as the deposition at the crystalline to amorphous transition, at high pressure depletion condition, by taming of the ion energy, by grading of the material growth, at reduced unwanted dopant incorporation, have helped to reach an efficiency of 10% for single junction nanocrystalline silicon cells. In situ plasma and gas phase diagnosis have contributed to the fast optimisation of deposition process parameters. Deposition rate, open circuit voltage and light confinement are some of most critical issues that are currently pursued. Materials with a defect density as low as 10¹⁵ cm⁻³ have been made, however, they are still not good enough for n–p junctions; the device structure is still of drift type in a p–i–n or n–i–p configuration.     

Analysis of the current linearity at low illumination of high‐efficiency back‐junction back‐contact silicon solar cells

The relation between current and illumination intensity of three structures of high‐efficiency back‐junction back‐contact silicon solar cells was analyzed. Both, n‐type cells with non‐diffused front surface and p‐type cell with floating n‐emitter show a pronounced non‐linearity due to strong illumination dependence of the passivation quality of the non‐diffused surface and the floating junction respectively. Quantum efficiency (QE) of this cell type drops significantly for the illumination lower than 0.5 suns. In contrast the QE of n‐type cells with n⁺‐front surface field (FSF) is linear. Low illumination current characteristics of all three of the analyzed structures could be well described by physical models. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Surface passivation schemes for high‐efficiency n‐type Si solar cells

An effective passivation on the front side boron emitter is essential to utilize the full potential of solar cells fabricated on n‐type silicon. However, recent investigations have shown that it is more difficult to achieve a low surface recombination velocity on highly doped p‐type silicon than on n‐type silicon. Thus, the approach presented in this paper is to overcompensate the surface of the deep boron emitter locally by a shallow phosphorus diffusion. This inversion from p‐type to n‐type surface allows the use of standard technologies which are used for passivation of highly doped n‐type surfaces. Emitter saturation current densities (J_0e) of 49 fA/cm² have been reached with this approach on SiO₂ passivated lifetime samples. On solar cells a certified conversion efficiency of 21.7% with an open‐circuit voltage (V_oc) of 676 mV was achieved. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

n‐type silicon solar cells with surface‐passivated screen‐printed aluminium‐alloyed rear emitter

Aluminium‐doped p‐type (Al‐p⁺) silicon emitters fabricated by means of a simple screen‐printing process are effectively passivated by plasma‐enhanced chemical‐vapour deposited amorphous silicon (a‐Si). We measure an emitter saturation current density of only 246 fA/cm², which is the lowest value achieved so far for a simple screen‐printed Al‐p⁺ emitter on silicon. In order to demonstrate the applicability of this easy‐to‐fabricate p⁺ emitter to high‐efficiency silicon solar cells, we implement our passivated p⁺ emitter into an n⁺np⁺ solar cell structure. An independently confirmed conversion efficiency of 19.7% is achieved using n‐type phosphorus‐doped Czochralski‐grown silicon as bulk material, clearly demonstrating the high‐efficiency potential of the newly developed a‐Si passivated Al‐p⁺ emitter. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical management in high‐efficiency thin‐film silicon micromorph solar cells with a silicon oxide based intermediate reflector

In the effort to increase the stable efficiency of thin film silicon micromorph solar cells, a silicon oxide based intermediate reflector (SOIR) layer is deposited in situ between the component cells of the tandem device. The effectiveness of the SOIR layer in increasing the photo‐carrier generation in the a‐Si:H top absorber is compared for p–i–n devices deposited on different rough, highly transparent, front ZnO layers. High haze and low doping level for the front ZnO strongly enhance the current density (J_sc) in the μc‐Si:H bottom cell whereas J_sc in the top cell is influenced by the angular distribution of the transmitted light and by the reflectivity of the SOIR related to different surface roughness. A total J_sc of 26.8 mA/cm² and an initial conversion efficiency of 12.6% are achieved for 1.2 cm² cells with top and bottom cell thicknesses of 300 nm and 3 μm, and without any anti‐reflective coating on the glass. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Rectifying properties and photoresponse of CVD diamond p(i)n‐junctions

The current–voltage characteristics and photoresponse of mesa structured {111}‐oriented homoepitaxial CVD diamond p(i)n‐junctions with different intrinsic layer thickness are investigated. When a sufficiently thick intrinsic layer is present, a rectification ratio of 10⁸ at ±10 V could be obtained. Good rectifying diodes show a high photoresponse ratio between 210 nm (above bandgap) and 500 nm (below bandgap), making them suitable for UV detection purposes. The results are compared with similar measurements carried out on polycrystalline CVD diamond pn‐junctions.

     

Short‐circuit current improvement of CuGaSe2 solar cells with a ZnS/(Zn,Mg)O buffer combination

CuGaSe₂ (CGS) thin‐film solar cells were prepared with an in‐line co‐evaporation process and the established buffer combination CdS/i‐ZnO was replaced by ZnS/(Zn,Mg)O. We obtained functional CGS solar cells with a strong gain in the short‐circuit current density as compared to the CdS/i‐ZnO buffer reference cells. The enhanced current density is a result of improved transmission in the wavelength region between 330 nm and 550 nm of the ZnS/(Zn,Mg)O buffer combination as compared to CdS/i‐ZnO. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Transparent,flexible and low‐resistive precision fabric electrode for organic solar cells

We report the use of conducting precision fabrics as transparent and flexible electrode for organic semiconductor‐based thin film devices. Precision fabrics have well‐defined mesh openings, excellent flexibility and are fabricated by high‐throughput roll‐to‐roll manufacturing. Optimized fabrics reached light transmittance over 95% throughout the visible and near infrared spectra. A significant part of the transmitted light is scattered, which is particularly advantageous for solar cell applications. Surface resistivity is as low as ～3 Ohms/square, which decreases Ohmic losses when scaling up to large area devices. We demonstrate that solar cells fabricated onto these electrodes show very similar characteristics to those prepared on ITO. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

High‐performance a‐Si1–xOx:H/c‐Si heterojunction solar cells realized by the a‐Si:H/a‐Si1–xOx:H stack buffer layer

We used amorphous silicon oxide (a‐Si_1–xO_x:H) and microcrystalline silicon oxide (µc‐Si_1–xO_x:H) as buffer layer and p‐type emitter layer, respectively, in n‐type silicon hetero‐junction (SHJ) solar cells. We proposed to insert a thin (2 nm) intrinsic amorphous silicon (a‐Si:H) thin film between the thin (2.5 nm) a‐Si_1–xO_x:H buffer layer and the p‐layer to form a stack buffer layer of a‐Si:H/a‐Si_1–xO_x:H. As a result, a high open‐circuit voltage (V_OC) and a high fill factor (FF) were obtained at the same time. Finally, a high efficiency of 19.0% (J_SC = 33.46 mA/cm², V_OC = 738 mV, FF = 77.0%) was achieved on a 100 μm thick polished wafer using the stack buffer layer.

     

Comparison of batch and in‐line PECVD of a‐Si:H passivation layers for silicon heterojunction solar cells

We present PECVD deposition of i‐a‐Si:H in an in‐line configuration for the fabrication of silicon heterojunction solar cells. For industry, in‐line processing has the potential to increase production throughput and yield. We compared batch and in‐line fabrication of i‐a‐Si:H passivation samples with identical plasma conditions and observed that the a‐Si:H material properties do not significantly differ. In batch‐type production the substrate is in the plasma zone at the moment of ignition, whereas for in‐line deposition the substrate is introduced into the plasma zone when steady plasma conditions have been reached. Our preliminary results show that there are depositions conditions that result both for in‐line and batch‐type deposition in good i‐a‐Si:H passivation layers. Therefore both methods can equally well be considered for the production of silicon heterojunction solar cells. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Light trapping for a‐Si:H/µc‐Si:H tandem solar cells using direct pulsed laser interference texturing

We present a‐Si:H/µc‐Si:H tandem solar cells on laser textured ZnO:Al front contact layers. Direct pulsed laser interference patterning (DLIP) was used for writing arrays of one‐dimensional micro gratings of submicron period into ZnO:Al films. The laser texture provides good light trapping which is indicated by an increase in short‐circuit current density of 20% of the bottom cell limited device compared to cells on planar ZnO:Al. The open‐circuit voltage of the cells on laser textured ZnO:Al is almost the same as for cells on planar substrates, indicating excellent growth conditions for amorphous and microcrystalline silicon on the U‐shaped grating grooves. DLIP is a simple, single step and industrially applicable method for large area periodic texturing of ZnO:Al thin films. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Tuning of the open‐circuit voltage by wide band‐gap absorber and doped layers in thin film silicon solar cells

We present an experimental study combined with computer simulations on the effects of wide band‐gap absorber and window layers on the open‐circuit voltage (V_oc) in single junction thin film silicon solar cells. The quantity ΔE_p, taking as the difference between the band gap and the activation energy in ?p? layer, is treated as a measure of the p‐layer properties and shows a linear relation with V_oc over a range of 100 mV with a positive slope of around 430 mV/eV. Two limiting mechanisms of V_oc are identified: the built‐in potential at lower ΔE_p and the band gap of the absorber layer at higher ΔE_p. The results of the experimental findings are confirmed by computer simulations. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

微晶硅锗薄膜作为近红外光吸收层在硅基薄膜太阳电池中的应用

采用射频等离子体增强化学气相沉积技术,制备了具有一定晶化率不同Ge含量的氢化微晶硅锗(μcSi1-xGex:H)薄膜.通过Ⅹ射线荧光谱、拉曼光谱、X射线衍射谱、傅里叶红外谱、吸收系数谱和电导率的测试,表征了μc-Si_(1-x)Ge_x:H的材料微结构随Ge含量的演变.研究表明:提高Ge含量可以增强μc-Si_(1-x)Ge_x:H薄膜的吸收系数.将其应用到硅基薄膜太阳电池的本征层中可以有效提高电池的短路电流密度(J_(sc)).特别是在电池厚度较薄或陷光不充分的情况下,长波响应的提高会更为显著.应用ZnO衬底后,在Ge含量分别为9%和27%时,μc-Si_(1-x)Ge_x:H太阳电池的转换效率均超过了7%.最后,将μc-Si_(1-x)Ge_x:H太阳电池应用在双结叠层太阳电池的底电池中,发现μc-Si_(0.73)Ge_(0.27):H底电池在厚度为800 nm时即可得到比1700 nm厚微晶硅(μc-Si:H)底电池更高的长波响应.以上结果体现μc-Si_(1-x)Ge_x:H太阳电池作为高效近红外光吸收层,在硅基薄膜太阳电池中应用的前景.