Alkaline and enzymatic degradation of L‐lactide copolymers. II. Crystallized films of poly(L‐lactide‐co‐D‐lactide) and poly(L‐lactide) with similar crystallinities

Films of poly(L ‐lactide‐co‐D ‐lactide) [P(LLA‐DLA); 95/5] and poly(L ‐lactide) [i.e., poly(L ‐lactide acid) (PLLA)] were prepared by crystallization from the melt, and a comparative study of the crystallization effects on the alkaline and proteinase K catalyzed hydrolysis of the films was carried out. The hydrolyzed films were investigated with gravimetry, differential scanning calorimetry, polarimetry, and gel permeation chromatography, and the results were compared with those reported for amorphous‐made specimens. The alkaline hydrolyzability of the P(LLA‐DLA) (95/5) and PLLA films was determined solely by the initial crystallinity (X_c) and was not affected by the content of the incorporated D ‐lactide (DLA) unit in the polymer chain; this was in marked contrast to the fact that the enzymatic hydrolyzability depended on not only the initial X_c value but also the DLA unit content. The alkaline hydrolysis rate of the P(LLA‐DLA) (95/5) and PLLA films and the enzymatic hydrolysis rate (R_EH) of the P(LLA‐DLA) (95/5) films decreased linearly as the initial X_c value increased. This meant that the hydrolyzability of the restricted amorphous regions was very similar to that of the free amorphous regions. In contrast, R_EH of the PLLA films decreased nonlinearly with the initial X_c value, and this nonlinear dependence was caused by the fact that in the PLLA films the restricted amorphous regions were much more hydrolysis‐resistant than the free amorphous regions. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1064‐1075, 2005     

Stereochemical heterogeneity of biodegradable poly(L‐lactide) homopolymer as revealed by temperature rising elution fractionation and successive self‐nucleation/annealing thermal fractionation

Commercial poly(L ‐lactide) is typically heterogeneous in chain structure due to the existence of a small amount of D ‐lactyl units that are produced by the racemization reactions during the synthesis. In this article, the stereochemical heterogeneity of two commercial poly(L ‐lactide) was investigated with temperature rising elution fractionation (TREF) and successive self‐nucleation/annealing (SSA) thermal fractionation. For both samples, three fractions were collected and characterized with rotatory power analysis and DSC. The fractions show distinct optical purity and DSC results, which reflect the structure differences among them directly. After SSA treatment, the observation of multiple endotherms for each physically separated fraction confirms the fractionated sample contains a heterogeneous intermolecular and intramolecular distribution of defects. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Synthesis of unimolecular reversed micelle consisting of a poly(L‐lactide) shell and hyperbranched D‐mannan core

A novel biodegradable unimolecular reversed micelle consisting of a poly(L ‐lactide) (PLA) shell and a hyperbranched D ‐mannan (HBM) core, that is, a chestnut‐shaped polymer (PLA–HBM), was synthesized by the polymerization of L ‐lactide on HBM with 4‐(dimethylamino)pyridine (DMAP) as the catalyst. The obtained polymers were soluble in dimethyl sulfoxide, tetrahydrofuran, and chloroform but insoluble in H₂O. The molecular weights of the PLA chain on PLA–HBM tended to increase with increasing polymerization time. The number of PLA chains on PLA–HBM could be controlled by the ratio of DMAP to the sugar unit in HBM. The obtained copolymer, PLA–HBM, acted as a unimolecular reversed micelle with an encapsulation ability toward the hydrophilic molecule. In addition, the entrapped hydrophilic molecules were slowly released from the core of PLA–HBM, and the release rate was accelerated by the breaking of the PLA chains of the shell when proteinase K as a hydrolase of PLA was used. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 406–413, 2006     

Light olefins/paraffins sorption in poly(lactic acid) films

The sorption behavior of small molecules like ethane and ethylene in poly (lactic acid) (PLA) was studied in the temperature interval from 283 to 313 K using a Quartz Crystal Microbalance (QCM). The effect of the polymer structure on the solubility selectivity of PLA films with respect to these two gases was studied using polymer with two different L:D ratios (98:2 and 80:20). Furthermore, the polymer films were submitted to different thermal treatments to address the influence of crystallinity and morphology of the noncrystalline fraction on the sorption behavior. The sorption results obtained indicate that ethylene solubility coefficient in annealed PLA 98:2 is about 26% higher than that of ethane and 41% higher in PLA 98:2 melted. The dual‐mode sorption model describes well the sorption isotherms behavior, which is concave concerning the pressure axis. The fully amorphous PLA presents the better selectivity for the studied gases, since the crystallinity seems to produce a negative effect on the selectivity. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1312–1319, 2008     

Synthesis and properties of bio‐based polyurethanes bearing hydroxy groups derived from alditols

Four kinds of bio‐based polyurethanes bearing hydroxy groups in the pendants were synthesized by the polyaddition of D ‐mannitol‐ and D,L ‐erythritol‐derived diols (1,2:5,6‐di‐O‐isopropylidene‐D ‐mannitol and 1,2‐O‐isopropylidene‐D,L ‐erythritol) with hexamethylene diisocyanate and methyl (S)‐2,6‐diisocyanatohexanoate and the subsequent deprotection of the isopropylidene groups. They were hydrolyzed much more quickly than the corresponding protected polyurethanes at 50 °C and pH 7.0, although their hydrolytic degradation rate was lower than that of polyurethanes with saccharic and glucuronic lactone groups, which had been reported in our previous articles. The introduction of D ‐mannitol units to the polyether‐polyurethanes containing poly(oxytetramethylene) glycol units also enhanced their hydrolyzibility. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of poly(lactide‐ran‐MOHEL) and its biodegradation with proteinase K

Homopoly(L ‐lactide) and homopoly(D,L ‐lactide) were almost inert for biodegradation with tricine buffer or normal enzymes such as bromelain, pronase, and cholesterol esterase but biodegradable with proteinase K. Significantly enhanced biodegradation was observed when an optically active (R)‐ or (S)‐3‐methyl‐4‐oxa‐6‐hexanolide (MOHEL) unit was introduced into poly(L ‐lactide) [poly(L ‐LA)] or poly(D,L ‐lactide) [poly(D,L ‐LA)] sequences. Poly[L ‐LA‐ran‐(R)‐MOHEL] in molar ratios of 86/14 to 43/57 showed good biodegradability that was independent of crystallinity. The biodegradation of polymers with proteinase K increased in the following order: poly[D,L ‐LA‐ran‐(R)‐MOHEL] > poly[L ‐LA‐ran‐(R)‐MOHEL] > poly[D,L ‐LA‐ran‐(S)‐MOHEL] > poly[L ‐LA‐ran‐(S)‐MOHEL] > poly(R)‐MOHEL > poly(D,L ‐LA). The number‐average molecular weight, molecular weight distribution, glass‐transition temperature, and melting temperature did not change before and after the biodegradation of poly[L ‐LA‐ran‐(R)‐MOHEL], indicating that the degradation occurred from the polymer surface. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1374–1381, 2001     

Dendritic homopolymers and block copolymers: Tuning the morphology and properties

The synthesis and characterization of dendritic homopolymers and block copolymers of ?‐caprolactone and lactide (L ‐lactide and racemic lactide) were performed with multifunctional initiators in combination with living polymerization and the selective placement of branching junctures in a divergent growth strategy. A hexahydroxy‐functional 2,2‐bis(hydroxymethyl) propionic acid derivative was used as an initiator for the stannous‐2‐ethylhexanoate‐catalyzed living ring‐opening polymerization of ?‐caprolactone, L ‐lactide, and racemic L ,D ‐lactide. Branching junctions at the chain ends were introduced with benzylidene‐protected 2,2‐bis(hydroxymethyl) propionic acid. Subsequent generations were then polymerized, after deprotection, from these star‐shaped macroinitiators. Successive chain end capping and initiation produced three generations of polymers with molecular weights in excess of 130,000 g/mol and narrow polydispersities (<1.20). It was possible to prepare diblock and triblock copolymers with phase‐separated morphologies, and with L ‐lactide or D ,L ‐lactide, semicrystalline and amorphous morphologies were demonstrated. The polymers were characterized by ¹H NMR, ¹³C NMR, size exclusion chromatography, and differential scanning calorimetry. The compositions of the block copolymers and the conformational structures of the optically active polymers were also confirmed by optical rotation measurements. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1174–1188, 2004     

Water‐disintegrative and biodegradable blends containing poly(L‐lactic acid) and poly(butylene adipate‐co‐terephthalate)

In this study, novel biodegradable materials were successfully generated, which have excellent mechanical properties in air during usage and storage, but whose structure easily disintegrates when immersed in water. The materials were prepared by melt blending poly(L ‐lactic acid) (PLLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) with a small amount of oligomeric poly(aspartic acid‐co‐lactide) (PAL) as a degradation accelerator. The degradation behavior of the blends was investigated by immersing the blend films in phosphate‐buffered saline (pH = 7.3) at 40 °C. It was shown that the PAL content and composition significantly affected morphology, mechanical properties, and hydrolysis rate of the blends. It was observed that the blends containing PAL with higher molar ratios of L ‐lactyl [LA]/[Asp] had smaller PBAT domain size, showing better mechanical properties when compared with those containing PAL with lower molar ratios of [LA]/[Asp]. The degradation rates of both PLLA and PBAT components in the ternary blends simultaneously became higher for the blends containing PAL with higher molar ratios of [LA]/[Asp]. It was confirmed that the PLLA component and its decomposed materials efficiently catalyze the hydrolytic degradation of the PBAT component, but by contrast that the PBAT component and its decomposed materials do not catalyze the hydrolytic degradation of the PLLA component in the blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Cyclic polypeptides by thermal polymerization of α‐amino acid N‐carboxyanhydrides

The NCAs of the following five amino acids were polymerized in bulk at 120 °C without addition of a catalyst or initiator: sarcosine (Sar), L ‐alanine (L ‐Ala), D ,L ‐phenylalanine (D ,L ‐Phe), D ,L ‐leucine (D ,L ‐Leu) and D ,L ‐valine (D,L ‐Val). The virgin reaction products were characterized by viscosity measurements ¹³C NMR spectroscopy and MALDI‐TOF mass spectrometry. In addition to numerous low molar mass byproducts cyclic polypeptides were formed as the main reaction products in the mass range above 800 Da. Two types of cyclic oligo‐ and polypeptides were detected in all cases with exception of sarcosine NCA, which only yielded one class of cyclic polypeptides. The efficient formation of cyclic oligo‐ and polypeptides explains why high molar mass polymers cannot be obtained by thermal polymerizations of α‐amino acid NCAs. Various polymerization mechanisms were discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4012–4020, 2008     

An efficient solid‐state polycondensation method for synthesizing stereocomplexed poly(lactic acid)s with high molecular weight

Simultaneous solid‐state polycondensation (SSP) of the powdery prepolymers of poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) can produce entire stereocomplexed poly(lactic acid)s (sc‐PLA) with high molecular weight and can be an alternative synthetic route to sc‐PLA. Ordinary melt polycondensations of L ‐ and D ‐lactic acids gave the PLLA and PDLA prepolymers having medium molecular weight which were pulverized for blending in 1:1 ratio. The resultant powder blends were then subjected to SSP at 130–160 °C for 30 h under a reduced pressure of 0.5 Torr. Some of the products thus obtained attained a molecular weight (M_w) as high as 200 kDa, consisting of stereoblock copolymer of PLLA and PDLA. A small amount of the stereocomplex should be formed in the boundaries of the partially melted PLLA and PDLA where the hetero‐chain connection is induced to generate the blocky components. The resultant SSP products showed predominant stereocomplexation after their melt‐processing in the presence of the stereoblock components in spite of containing a small amount of racemic sequences in the homo‐chiral PLLA and PDLA chains. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3714–3722, 2008     

Synthesis of poly(D,L‐lactic acid‐alt‐glycolic acid) from D,L‐3‐methylglycolide

D ,L ‐3‐Methylglycolide (MG) was synthesized via two step reactions with a good yield (42%). It was successfully polymerized in bulk with stannous octoate as a catalyst at 110 °C. The effects of the polymerization time and catalyst concentration on the molecular weight and monomer conversion were studied. Poly(D ,L ‐lactic acid‐co‐glycolic acid) (D ,L ‐PLGA50; 50/50 mol/mol) copolymers were successfully synthesized from the homopolymerization of MG with high polymerization rates and high monomer conversions under moderate polymerization conditions. ¹H NMR spectroscopy indicated that the bulk ring‐opening polymerization of MG conformed to the coordination–insertion mechanism. ¹³C NMR spectra of D ,L ‐PLGA50 copolymers obtained under different experimental conditions revealed that the copolymers had alternating structures of lactyl and glycolyl. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4179–4184, 2000     

Higher order structural analysis of stereocomplex‐type poly(lactic acid) melt‐spun fibers

The higher order structure of stereocomplex‐type poly(lactic acid) melt‐spun fibers of an equimolar blend of poly(L ‐lactic acid) and poly(D ‐lactic acid) was analyzed with wide‐angle X‐ray diffraction (WAXD) and birefringence measurements. Two different crystalline structures were observed in the fibers: α‐form homocrystals and stereocomplex crystals. The weight fractions of the two crystals were estimated with the WAXD integrated intensity data. The crystalline orientation factors were obtained from the WAXD measurements. Well‐oriented homocrystals formed during a drawing process at the crystallization temperature of the homocrystal. Drawing above this temperature caused the stereocomplex crystal to be formed. The crystalline orientation tended to be lower with increasing drawing temperatures. Through the combination of the intrinsic birefringence and the fractions of the α‐form homocrystals and stereocomplex crystals, the birefringence of the amorphous phase was evaluated. The amorphous birefringence stayed positive and decreased with increasing drawing temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 218–228, 2007     

Microspheres from stereocomplexes of polylactides containing ionic liquid end‐groups

Low‐molecular‐weight polymers of L ‐ and D ‐lactide containing different end‐groups (hydroxy, butoxy, trifluoromethoxy, heptafluorobutoxy, oxyethylimidazole groups, and groups derived from the imidazolium ionic liquid) are synthesized. It is shown that the nature of end‐groups affects the stereocomplexation of corresponding pairs of polymers. Stereocomplex of poly(L ‐lactide) and poly(D ‐lactide) containing imidazolium ionic liquid end‐groups (PLA‐IL) precipitates from 1,4‐dioxane solution in the form of monodisperse, perfectly spherical microspheres. Such behavior of PLA‐IL, not observed for polymers containing other end‐groups, can be attributed to the presence of strongly interacting ionic liquid end‐groups. This conclusion is supported by the results of ¹H NMR and dynamic light scattering experiments as well as by direct observation of precipitated particles by scanning electron microscopy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation of flexible and transparent polylactic acids films by crystallization manipulation

Highly flexible and transparent polylactic acids (PLAs) films were successfully prepared by manipulating their crystallization. The semicrystalline poly(L ‐lactic acid) (L) was blended with a noncrystalline poly(DL ‐lactic acid) (DL) together with diglycerol tetraacetate (DGTA). Optimal DGTA content to plasticize PLAs was about 17%. Addition of DL hindered the crystallization of the films. Tensile strengths of the films having DL content more than 5% were about 10 MPa while the elongations at break were boosted as DL content increased. Films having L/DL ratio of 50/50 showed elongations at break of 270%. Stretch ability and clarity of films containing 15–50% DL were fair although they were subjected to annealing at 60 °C for 1 h. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6489–6495, 2008     

Highly biodegradable copolymers composed of chiral depsipeptide and L‐lactide units with favorable physical properties

Syntheses of copolymers composed of optically active depsipeptides (3,6‐dimethyl‐2,5‐morphorinedione) and L ‐lactide—poly(L ‐3,L ‐6‐dimethyl‐2,5‐morphorinedione‐co‐L ‐lactide), poly(L ‐3,DL ‐6‐dimethyl‐2,5‐morphorinedione‐co‐L ‐lactide), and poly(L ‐3,D ‐6‐dimethyl‐2,5‐morphorinedione‐co‐L ‐lactide)—were examined in an effort to improve the biodegradability and physical properties of homopoly(L ‐lactide). In degradation tests, the copolymers composed of 3,6‐dimethyl‐2,5‐morphorinedione and lactide in the ratios 10/90 to 13/87 exhibited high biodegradability toward proteinase K, whereas a homopolymer, poly(L ‐lactide), exhibited very poor biodegradability (only 50% after 200 h). These polymers composed of 3,6‐dimethyl‐2,5‐morphorinedione/L ‐lactide in 11/89 to 13/87 ratios also degrades rapidly after being in compost for 30 days. The resulting copolymers, however, showed relatively low elongation properties. Therefore, ternary copolymerizations of L ‐3,DL ‐6‐dimethyl‐2,5‐morphorinedione, ?‐caprolactone, and L ‐lactide were explored in an effort to improve their mechanical properties, especially the elongation, and sufficient results were obtained with an approximate ratio of 3/11/86. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 302–316, 2002     

Polyesters analogous to PET and PBT based on O‐benzyl ethers of xylitol and L‐arabinitol

The synthesis, characterization, and some properties of new copolyesters of poly(butylene terephthalate) (PBT) and poly(ethylene terephthalate) (PET) based on L ‐arabinitol and xylitol are described. These copolyesters were obtained by polycondensation reaction in the melt of mixtures of 1,4‐butanediol or ethylene glycol and 2,3,4‐tri‐O‐benzyl‐L ‐arabinitol or 2,3,4‐tri‐O‐benzyl‐xylitol with dimethyl terephthalate. Their weight‐average molecular weights ranged between 7000 and 55,000, with polydispersities ranging from 1.4 to 4.7. Copolymers containing 1,4‐butanediol could be analyzed by NMR, and were found to have a statistical microstructure. All these copolyesters were thermally stable, with degradation temperatures well above 300 °C. With increasing amounts of alditol in the copolyester, the melting temperature and crystallinity decreased in both series, and the glass transition temperature increased for the PBT series and decreased for the PET series. Only PBT‐derived copolyesters containing a maximum of 10% alditol units showed discrete scattering characteristic of crystalline material. No substantial differences in either structure or properties were observed between the L ‐arabinitol and xylitol copolyester series. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5167–5179, 2008     

Some composting and biodegradation effects of physically or chemically crosslinked poly(lactic acid)

Polylactide (PLA) crosslinked by using both triallyl isocyanurate (TAIC) and electron radiation or using dicumyl peroxide (DCP) was studied with the aim of examining the behaviour of the modified polymer under various environmental conditions. Thus, the polymer samples were subjected to composting in an industrial pile, exposed to proteinase K, or incubated in sea water. The number-average molecular weight (M_n), melt flow index (MFI), crystallinity (χ), tensile strength (σ_M) and mass loss (in the case of samples treated with proteinase K) were determined. It was found that neat PLA irradiated with high-energy electrons underwent degradation that increased during composting. As a result, the value of M_n of this polymer dramatically decreased. It appeared that PLA crosslinked with TAIC and electron radiation contained, in addition to the crosslinked phase, a phase strongly degraded by this radiation, which facilitated hydrolytic degradation during composting. The σ_M value of PLA crosslinked with TAIC and electron radiation rapidly decreased during composting, whereas that of PLA crosslinked chemically and composted for three weeks slightly increased. As the electron radiation dose increased, the mass loss of PLA containing TAIC and treated with proteinase K decreased, which indicated that the physical crosslinking of PLA hindered enzymatic degradation of this polymer. Important changes in both neat and physically crosslinked PLA incubated in sea water for nine weeks were not detected.     

Synthesis of poly(ethylene glycol)/polypeptide/poly(D,L‐lactide) copolymers and their nanoparticles

Core‐shell structured nanoparticles of poly(ethylene glycol) (PEG)/polypeptide/poly(D ,L ‐lactide) (PLA) copolymers were prepared and their properties were investigated. The copolymers had a poly(L ‐serine) or poly(L ‐phenylalanine) block as a linker between a hydrophilic PEG and a hydrophobic PLA unit. They formed core‐shell structured nanoparticles, where the polypeptide block resided at the interface between a hydrophilic PEG shell and a hydrophobic PLA core. In the synthesis, poly(ethylene glycol)‐b‐poly(L ‐serine) (PEG‐PSER) was prepared by ring opening polymerization of N‐carboxyanhydride of O‐(tert‐butyl)‐L ‐serine and subsequent removal of tert‐butyl groups. Poly(ethylene glycol)‐b‐poly(L ‐phenylalanine) (PEG‐PPA) was obtained by ring opening polymerization of N‐carboxyanhydride of L ‐phenylalanine. Methoxy‐poly(ethylene glycol)‐amine with a MW of 5000 was used as an initiator for both polymerizations. The polymerization of D ,L ‐lactide by initiation with PEG‐PSER and PEG‐PPA produced a comb‐like copolymer, poly(ethylene glycol)‐b‐[poly(L ‐serine)‐g‐poly(D ,L ‐lactide)] (PEG‐PSER‐PLA) and a linear copolymer, poly(ethylene glycol)‐b‐poly(L ‐phenylalanine)‐b‐poly(D ,L ‐lactide) (PEG‐PPA‐PLA), respectively. The nanoparticles obtained from PEG‐PPA‐PLA showed a negative zeta potential value of ?16.6 mV, while those of PEG‐PSER‐PLA exhibited a positive value of about 19.3 mV. In pH 7.0 phosphate buffer solution at 36 °C, the nanoparticles of PEG/polypeptide/PLA copolymers showed much better stability than those of a linear PEG‐PLA copolymer having a comparable molecular weight. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Linear polyurethanes made from threitol: Acetalized and hydroxylated polymers

A set of novel linear polyurethanes was synthesized by reaction in solution of 1,6‐hexamethylene diisocyanate (HDI) or 4,4′‐methylene‐bis(phenyl diisocyanate) with 2,3‐acetalized threitols, specifically, 2,3‐O‐methylidene‐L ‐threitol and 2,3‐O‐isopropylidene‐D ‐threitol. The polyurethanes containing acetalized threitols had weight‐average molecular weights between 40,000 and 65,000 Da. Most of them were amorphous and they displayed T_g higher than their unsubstituted analogs. Deprotection of acetalized polyurethanes by treatment with acid allowed preparing semicrystalline polyurethanes bearing two free hydroxyl groups in the repeating unit. The crystalline structure and crystallizability of the hydroxylated polyurethane made from HDI were investigated taken as reference the polyurethane made from 1,4‐butanediol and HDI. The hydrolytic degradability of threitol derived polyurethanes was comparatively evaluated under a variety of conditions. Highest degradation rates were obtained upon incubation at pH 10 at temperatures above T_g, the aliphatic hydroxylated polyurethane being the fastest degrading compound. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7996–8012, 2008     

Crystallization and stereocomplexation behavior of poly(D‐ and L‐lactide)‐b‐poly(N,N‐dimethylamino‐2‐ethyl methacrylate) block copolymers

The thermal properties, crystallization, and morphology of amphiphilic poly(D ‐lactide)‐b‐poly(N,N‐dimethylamino‐2‐ethyl methacrylate) (PDLA‐b‐PDMAEMA) and poly (L ‐lactide)‐b‐poly(N,N‐dimethylamino‐2‐ethyl methacrylate) (PLLA‐b‐PDMAEMA) copolymers were studied and compared to those of the corresponding poly(lactide) homopolymers. Additionally, stereocomplexation of these copolymers was studied. The crystallization kinetics of the PLA blocks was retarded by the presence of the PDMAEMA block. The studied copolymers were found to be miscible in the melt and the glassy state. The Avrami theory was able to predict the entire crystallization range of the PLA isothermal overall crystallization. The melting points of PLDA/PLLA and PLA/PLA‐b‐PDMAEMA stereocomplexes were higher than those formed by copolymer mixtures. This indicates that the PDMAEMA block is influencing the stability of the stereocomplex structures. For the low molecular weight samples, the stereocomplexes particles exhibited a conventional disk‐shape structure and, for high molecular weight samples, the particles displayed unusual star‐like shape morphology. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1397–1409, 2011