Effect of electric field on electrocaloric effect in Pb(Zr1 − xTix)O3 solid solution

A thermodynamic analysis is employed to investigate the intrinsic electrocaloric effect of Pb(Zr_1 − xTi_x)O₃ solid solution system under the different electric field. Theoretical analysis indicates that Pb(Zr_1 − xTi_x)O₃ system has the giant electrocaloric coefficient and the large adiabatic temperature change near its ferroelectric Curie temperature. The applied electric field decreases not only the electrocaloric coefficient but also its temperature dependence. Furthermore, it increases the adiabatic temperature change as well as its dependence of temperature. The temperature corresponding to the maximum of electrocaloric coefficient and adiabatic temperature change increases with the enhancement of electric field because of its first-order phase transition between ferroelectric phase and paraelectric phase.     

Nanoscale resistive switching in SrTiO3 thin films

The local conductivity of SrTiO₃ thin films epitaxially grown on SrRuO₃‐buffered SrTiO₃ single crystals has been investigated in detail with an atomic force microscope equipped with a conducting tip (LC‐AFM). These experiments demonstrate that the conductivity of SrTiO₃ thin films originates from nanoscale well‐conducting filaments connecting the surface to the SrRuO₃ bottom electrode. The electrical conduction of the filaments is shown to be reversibly modulated over several orders of magnitude by application of an appropriate electrical field. We analyze the resistive switching by addressing individual filaments with the AFM tip as well as by scanning areas up to the µm scale. Temperature dependent measurements reveal that resistive switching on a macroscopic scale can be traced down to the insulator‐to‐metal transition of the independently switchable filaments. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of microstructures on exchange bias behaviors of La0.7Sr0.3MnO3/La0.33Ca0.67MnO3 bilayers

Ferromagnetic La_0.7Sr_0.3MnO₃ (LSMO) and antiferromagnetic La_0.33Ca_0.67MnO₃ (LCMO) layers were grown on SrTiO₃ (STO) substrates by the pulsed laser deposition technique. LSMO films had rougher surfaces and larger grain sizes than LCMO films. Fully strained bilayers, in which each layer was as thin as 10 nm, were prepared by changing their stacking sequences, i.e. LSMO/LCMO/STO and LCMO/LSMO/STO. The former had higher T_C (350 K) than the latter (300 K), and exchange bias effects were only observed in the former bilayers. This revealed that microstructures could play an important role in the transport and magnetic properties of manganese oxide thin films.     

The influence of Co doping on the dielectric, ferroelectric and ferromagnetic properties of Ba0.70Sr0.30TiO3 thin films

Ba_0.70Sr_0.30TiO₃ (BST) thin films doped by Co (BSTC) are fabricated by sol-gel method on a Pt/Ti/SiO₂/Si substrate. A strong correlation is observed among the microstructure, dielectric, ferroelectric, ferromagnetic properties and Co concentration. The dielectric constant of BST thin films can be tailored from 343 to 119 by manipulating the Co concentration. The dielectric loss of BSTC thin films are still kept below 0.020 and the tunability is above 30% at a dc-applied electric field of 500 kV/cm. With increasing Co doping up to 10 mol%, the coexistence of ferromagnetism and ferroelectrics is found. Suitable dielectric constant, low-dielectric loss, and high tunability of this kind of thin films can be useful for potential tunable applications.     

Sol-gel-derived pyroelectric barium strontium titanate thin films for infrared detector applications

Quality pyroelectric Ba_0.8Sr_0.2TiO₃ films have been successfully fabricated by a sol-gel processing using a highly diluted precursor solution. The remnant polarization of the films decreases with the temperature increasing, which results in a large pyroelectric coefficient at room temperature. Infrared response measured using a 500-K chopped blackbody at room temperature exhibits a typical pyroelectric response waveform. Frequency dependence of the infrared response measurement for a pixel with area of 2.5×10^-3 cm² showed that the maximum response output voltage of 3.2 mV was obtained at 6 Hz. Better infrared response can be expected by the improvement in thermal isolation of the pixels and electrode materials. Received: 26 April 2000 / Accepted: 9 May 2000 / Published online: 9 August 2000     

Dependence of excess bismuth content in precursor sols on ferroelectric and dielectric properties of Bi3.25La0.75Ti3O12 thin films fabricated by chemical solution deposition

Bi_3.25La_0.75Ti₃O₁₂ (BLT) thin films were fabricated on Pt/Ti/SiO₂/Si(1 0 0) substrates by chemical solution deposition (CSD), and the dependence of ferroelectric and dielectric properties of the as-deposited BLT thin films on excess Bi content in precursor sols was studied. It is found that the prepared BLT thin film shows the best polarization-electric field, capacitance-voltage and dielectric constant (?_r)-frequency characteristics, when the value of excess Bi content in precursor sols is 10%. In detail, its remnant polarization (2P_r) value is 40 μC/cm², the capacitance tunability is 21% measured at room temperature under conditions of an applied voltage of 8 V and measurement frequency of 10 kHz, and the ?_r is 696 at 100 kHz frequency.     

Enhanced ferroelectric properties of vanadium doped bismuth titanate (BTV) thin films grown by pulsed laser ablation technique

Bi_3.99Ti_2.97V_0.03O₁₂ (BTV) thin films were grown by pulsed laser deposition at substrate temperatures ranging between 650 and 750 °C. The structural phase, and orientation of the deposited films were investigated in order to understand the effect of the deposition parameters on the properties of the BTV films. As the substrate temperature was increased to 700 °C, the films started showing a tendency of assuming a c-axis preferred orientation, while at lower temperatures polycrystalline films were formed. The Au/BTV/Pt capacitor showed an interesting dependence of the remnant polarization (P_r) as well as dc leakage current values on the growth temperature. The film deposited at 675 °C showed a very large 2P_r of 42 μC cm⁻², which is the largest for BTV thin films among the values reported so far.     

Multiferroic properties of Bi0.8La0.2FeO3/CoFe2O4 multilayer thin films

Bi_0.8La_0.2FeO₃/CoFe₂O₄ (BLFO/CFO) multilayer thin films (totally 20 layers BLFO and 19 layers CFO) were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and transmission electron microscope measurements show that the films are polycrystalline and consisted of multilayered structure. Ferroelectric hysteresis loops with remnant polarization and saturated polarization of 4.2 and 13.3 μC/cm², respectively, were observed. On the other hand, the films show well-shaped magnetization hysteresis loops with saturated and remnant magnetization of 34.7 and 11.4 emu/cm³, respectively, which are significantly larger than pure BLFO thin films deposited under the same conditions. These results indicate that constructing epitaxial superlattice might be a promising way to fabricate multiferroics with improved properties.     

Interfacial spin interactions of ferromagnetic and antiferromagnetic manganite bilayers

A pulsed laser deposition technique was used to grow ferromagnetic La_0.7Sr_0.3MnO₃ (LSMO) films on antiferromagnetic La_0.33Ca_0.67MnO₃ (LCMO) and Pr_0.7Ca_0.3MnO₃ (PCMO) films in bilayer forms. The LSMO film on the PCMO layer had a more elongated out-of-plane lattice than that on the LCMO layer. The former had a lower ferromagnetic transition temperature (320 K) than the latter (350 K). The enhanced low-temperature magnetoresistance of the LSMO/PCMO bilayer suggests that the spin frustration is stronger at this bilayer than in the LSMO/LCMO bilayer. These differences indicate that strain state and defect concentration play important roles in governing interfacial spin interactions.     

The electrical properties and phase transformation of PLZST 2/85/13/2 antiferroelectric thin films on different bottom electrode

Pb_0.97La_0.02(Zr_0.85Sn_0.13Ti_0.02)O₃ (PLZST 2/85/13/2) antiferroelectric thin films were deposited on Pt(111)/Ti/SiO₂/Si and LaNiO₃(LNO)/SiO₂/Si substrates through a modified sol-gel process. The phase structure and microstructure of PLZST 2/85/13/2 antiferroelectric thin films were analysed by x-ray diffraction (XRD), scanning electron microcopy (SEM) and field-emission SEM (FE-SEM). The antiferroelectric nature of the PLZST 2/85/13/2 thin films on two electrodes was demonstrated by the C-V (capacitance-voltage) and P-E (polarization-electric field) measurement. The maximum polarizations for PLZST 2/85/13/2 films on Pt and LNO electrodes were 42 and 18 μC/cm², respectively. The temperature dependence of the dielectric property of the PLZST 2/85/13/2 films was measured under different dc electric fields. Also, the phase transformation of the PLZST 2/85/13/2 films was studied in detail as a function of temperature and dc electric field.     

Magnetodielectric coupling in Ca3Co2O6 triangular Ising lattice

Geometric frustration in magnetic systems is a key ingredient for magnetodielectric coupling. Ca₃Co₂O₆ system is a model of triangular Ising lattice and presenting exotic magnetic properties. With a partially disordered antiferromagnetic ground state and two steps in magnetisation to a ferrimagnetic state and to a ferromagnetic state, this oxide is a good system for studying the effect of frustration in magnetodielectric coupling. Dielectric constant measurements of single crystals of Ca₃Co₂O₆ have been done showing the sensitivity of this technique to frustration.     

Aluminium oxide thin films prepared by plasma-enhanced chemical vapour deposition

Thin films of aluminium oxide have been deposited on glass, quartz, Si(100), steel, nickel, and aluminium by plasma-enhanced chemical vapour deposition (PECVD) using aluminium acetylacetonate (Al(acac)₃) as precursor. The deposits are hard (up to 2370 HK) and show good adherence to the substrates. The influence of various experimental parameters on deposition rate, film composition and hardness has been studied. The bias turned out to be the most effective parameter.On leave from Beijing Solar Energy Research Institute, Beijing, P.R. China     

Electrical properties of highly (111)-oriented lead zirconate thin films

Antiferroelectric PbZrO₃ thin films were grown on Pt/Ti/SiO₂/Si substrates with predominant (111) orientation using a sol-gel process. The Pt/PbZrO₃/Pt film capacitor showed well-saturated hysteresis loops at an applied voltage of 5 V with remanent polarisation (P_r) and coercive electric field (E_c) values of 8.97 μC/cm² and 162 kV/cm, respectively. The leakage current density of the highly (111)-oriented PbZrO₃ film was less than 1.0×10⁻⁷ A/cm² over electric field ranges from 0 to 105 kV/cm. The conduction current depended on the voltage polarity. The PbZrO₃/Pt interface forms a Schottky barrier at electric fields from 20 to 160 kV/cm. The dielectric relaxation current behaviour of Pt/PbZrO₃/Pt capacitor obeys the well-known Curie-Von Schweidler law at electric field of 20-80 kV/cm, the currents have contributions of both dielectric relaxation current and leakage current.     

Ferroelectric properties of Bi3.25−x/3La0.75Ti3−xNbxO12 films prepared by pulsed laser deposition

Bi₄Ti₃O₁₂ (BiT), Bi_3.25La_0.75Ti₃O₁₂ (BLT), Bi_4−x/3Ti_3−xNb_xO₁₂ (BTN) and Bi_3.25−x/3La_0.75Ti_3−xNb_xO₁₂ (BLTN) thin films have been prepared by pulsed laser deposition. BTN and BLTN films exhibit a maximum in the remanent polarization P_r at a Nb content x=0.018. At this Nb content, the BLTN film has a P_r value (25 μC/cm²) that is much higher than that of BiT and a coercive field similar to that of BiT. The polarization of this BLTN film is fatigue-free up to 10⁹ switching cycles. The high fatigue resistance is mainly due to the substitution of Bi³⁺ ions by La³⁺ ions at the A site and the enhanced P_r arises largely from the replacement of Ti⁴⁺ ions by Nb⁵⁺ ions at the B site. The mechanisms behind the effects of the substitution at the two sites are discussed.     

Controllable microstructures and multiferroic properties of Pb(Zr0.53Ti0.47)O3-CoFe2O4 composite films

1-3 and 2-2 types Pb(Zr_0.53Ti_0.47)O₃-CoFe₂O₄ (PZT-CFO) composite films with controllable microstructures, consisted by CFO nanopillar embedded in PZT matrix and PZT-CFO gratings respectively, have been fabricated on Pt/Ti/SiO₂/Si substrates by combining lithography technology and pulsed laser deposition. X-ray diffraction confirms that the films are well crystallized under optimized postannealing conditions. Scanning electron microscope reveals that the periodic microstructures can be well controlled. Especially, intrinsic room temperature ferroelectric and ferrimagnetic behaviors are observed simultaneously. The structure-properties relationship is discussed. Our results may provide an alternative method to design and prepare multiferroic composite films with controllable microstructures.     

Growth and thermal stability of epitaxial BiFeO3 thin films

We have investigated the oxygen pressure and the temperature dependence on BiFeO₃ thin films deposited on SrTiO₃ substrates by pulsed laser deposition. Reflection high energy electron diffraction (RHEED), atomic force microscopy (AFM) and X-ray diffraction measurements indicate that high-quality epitaxial thin films are obtained for and T=650 °C. Outside of this pressure-temperature window, parasitic peaks attributed to β-Bi₂O₃ appear. We find an increase of the out-of-plane lattice parameter with oxygen pressure that we ascribe to Bi-deficiency due to its high volatility at low pressure. Ex-situ anneals have been performed and results show that as-grown single-phase BiFeO₃ thin films degrade after annealing, whereas as-grown BiFeO₃ containing impurity phases evolve toward a single-phase structure. These experiments demonstrate that parasitic phases can stabilize compounds which are usually unstable in air at elevated temperatures.     

Influence of crystallization on the spectral features of nano-sized ferroelectric barium strontium titanate (Ba0.7Sr0.3Tio3) thin films

Ferroelectric barium strontium titanate (Ba_0.7Sr_0.3TiO₃)(BST) thin films have been prepared from barium 2-ethylhexanoate [Ba[CH₃(CH₂)₃CH(C₂H₅)CO₂]₂]_, strontium 2-ethylhexanoate [Sr[CH₃(CH₂)₃CH(C₂H₅)CO₂]₂] and titanium(IV) isopropoxide [TiOCH(CH₃)₂]₄ precursors using a modified sol-gel technique. The precursor except [TiOCH(CH₃)₂]₄ were synthesized in the laboratory. Transparent and crack-free films were fabricated on pre-cleaned quartz substrates by spin coating. The structural and optical properties of films annealed at different temperatures have been investigated. The as-fired films were found to be amorphous that crystallized to the tetragonal phase after annealing at 550 °C for 1 h in air. The lattice constants “a” and “c” were found to be 3.974 A and 3.990 A, respectively. The grain sizes of the films annealed at 450, 500 and 550 °C were found to be 30.8, 36.0 and 39.8 nm respectively. The amorphous film showed very high transparency (∼95%), which decreases slightly after crystallization (∼90%). The band gap and refractive index of the amorphous and crystalline films were estimated. The optical dispersion data are also analyzed in the light of the single oscillator model and are discussed.     

Surface effects in thin films of antiferroelectric smectic liquid crystals in terms of the short-pitch long-pitch competition model

A theoretical model based on the competition between short-pitch and long-pitch types of helical order is developed for thin films of antiferroelectric smectic liquid crystals. In the case of the “bookshelf” structure of the film and non-polar surfaces, subsurface perturbations of the ordering are found out analytically. Corresponding contributions to the free energies of the different phases are analysed. The possibility of sufficient influence of the boundaries on phase sequences is predicted even in the case of weak surface anchoring. A consistent explanation of the controversial experimental information is given; further ways of experimental justification of the model assumptions are discussed. Received 23 May 2002 RID="a" ID="a"e-mail: mgorkoun@uos.de     

Simulation of flexoelectricity effect on imprint behavior of ferroelectric thin films

The impact of flexoelectricity on the imprint behavior in ferroelectric thin films has been investigated within the framework of Landau-Khalatnikov theory, by incorporating the coupling effect between the stress gradient and polarization. It is found that the imprint phenomenon can be in part induced by flexoelectricity. In the presence of flexoelectric coupling, the compressive stress shifts the hysteresis loop to the negative electric field axis, but the tensile stress shifts it to the opposite direction, which is in good agreement with experimental result. Besides, the characteristic length of stress distribution has a significant influence on the upper part of hysteresis loop. It highlights the pressing need to avoid the stress gradient in order to prevent degradation of device performance in ferroelectric thin films.     

Enhanced field emission from Si doped nanocrystalline AlN thin films

Si doped and undoped nanocrystalline aluminum nitride thin films were deposited on various substrates by direct current sputtering technique. X-ray diffraction analysis confirmed the formation of phase pure hexagonal aluminum nitride with a single peak corresponding to (1 0 0) reflection of AlN with lattice constants, a = 0.3114 nm and c = 0.4986 nm. Energy dispersive analysis of X-rays confirmed the presence of Si in the doped AlN films. Atomic force microscopic studies showed that the average particle size of the film prepared at substrate temperature 200 °C was 9.5 nm, but when 5 at.% Si was incorporated the average particle size increased to ∼21 nm. Field emission study indicated that, with increasing Si doping concentration, the emission characteristics have been improved. The turn-on field (E_to) was 15.0 (±0.7) V/μm, 8.0 (±0.4) V/μm and 7.8 (±0.5) V/μm for undoped, 3 at.% and 5 at.% Si doped AlN films respectively and the maximum current density of 0.27 μA/cm² has been observed for 5 at.% Si doped nanocrystalline AlN film. It was also found that the dielectric properties were highly dependent on Si doping.