Preparation and electro‐optical properties of polymer dispersed liquid crystal films with relatively low liquid crystal content

In this paper, polymer dispersed liquid crystals (PDLC) films with LC content as low as 40 wt% were prepared, and the electro‐optical properties were carefully investigated. To accomplish this, different (meth)acrylate copolymerizaiton monomers have been used. The electro‐optical properties and morphologies of the PDLC films were strongly influenced by the chemical structure of copolymerization monomers (hydroxypropyl methacrylate (HPMA), glycidyl methacrylate, hydroxypropyl acrylate) and their feed ratio. Lower driven voltage and higher contrast ratio were achieved when the PDLC films showed a morphology with suitably LC domain size. At high HPMA content, a thin polymer film was formed on the surface of PDLC samples, which is beneficial to decrease the total LC content in PDLC devices. Copyright © 2013 John Wiley & Sons, Ltd.     

Studies on electro‐optical properties of polymer matrix/LC/ITO nanoparticles composites

In this paper, polymer‐dispersed liquid crystal (PDLC) films consisting of liquid crystal (LC)/monomers/indium tin oxide (ITO) nanoparticles with good near‐infrared absorption property had been fabricated, and the influence of the ITO nanoparticles modified with 3‐methacryloxypropyltrimethoxysilane (KH570) on the PDLC films was systematically studied. First, different liquid crystal content was studied to obtain PDLC films with good electro‐optical properties. And then, various weight ratio of ITO nanoparticles was added to samples. While the content of ITO nanoparticles was increased, the saturation voltage increased and the CR decreased. Though the electro‐optical properties of PDLC samples reduced with the addition ITO nanoparticles, the near‐infrared absorption property of films was enhanced.     

Effects of crosslinking agent,cure temperature,and UV flux on the electro‐optical properties of polymer‐dispersed liquid crystal cells

We present results for the effects of a crosslinking agent, cure temperature, and UV flux on the electro‐optical properties of polymer‐dispersed liquid crystal (PDLC) cells. These cells were fabricated using a mixture of a liquid crystal (E8) and an acrylic monomer (CN135). The maximum in the first derivative of the transmission vs. applied, sinusoidal voltage (inflection voltage, V_inf), varies systematically with PDLC formulation and cure‐process conditions. For PDLC cells fabricated with a crosslinking agent (SR295), V_inf increases with increasing the concentration of SR295. However, for cells fabricated without the use of a crosslinking agent, V_inf decreases with increasing the UV flux and decreasing temperature. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 404–410, 2004     

Effect of molecular weight of macro‐iniferter on electro‐optical properties of polymer dispersed liquid crystal films prepared by iniferter polymerization

Polymer dispersed liquid crystal (PDLC) films were prepared by a devised method, in which photo‐polymerization induced phase separation in a mixtures of a macro‐iniferter, methyl acrylater, and liquid crystal. The morphology of the obtained PDLC films was examined on a polarized optical microscopy, and the effect of molecular weight of MIs on the electro‐optical properties was deliberately investigated. Decreasing the molecular weight of MIs in the films led to formation of larger liquid crystal droplets and a lower V_th values. V_sat increased and the memory effect decreased because of the increased interface anchoring strength induced by the higher molecular weight of polymer matrices. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1530–1534, 2009     

TSC study and electro‐optical properties of epoxy/acrylic polymer‐dispersed liquid‐crystal film in DICY thermal cure

We report on the structures and electro‐optical properties of epoxy/acrylic polymer‐dispersed liquid‐crystal (PDLC) films. A thermal stimulated current (TSC) analysis was used to investigate the physical structures of PDLC. In the TSC spectrum of PDLC, three relaxation peaks were observed: the glass transition of the liquid crystal, the glass transition of the polymer matrix, and the ρ transition. The ρ transition represents the discharge behavior of space charges, and its intensity increased as the curing time and content of the curing agent dicyandiamide (DICY) increased. The pre‐UV‐cured films with different DICY contents were thermally cured at 130 °C for various periods. The electro‐optical properties of PDLC, such as the contrast ratio and switching voltage, increased as the curing time of DICY, the content of DICY, or both increased. As the ambient temperature increased from 10 to 40 °C, the contrast ratio and switching voltage of PDLC gradually decreased. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 507–514, 2001     

A study on the polymer structures and electro-optical properties of epoxy-mercaptan-based polymer dispersed liquid crystal films

ABSTRACT

In this paper, polymer dispersed liquid crystal (PDLC) films based on epoxy-mercaptan system were prepared by thermal-initiated polymerization. The effects of the liquid crystal (LC) content, the proportion and the functionality of epoxy monomers on the polymer structures and electro-optical properties of the as-made PDLC films were investigated systematically. It was found that the morphologies of the polymer matrix can be altered from polymer meshes to polymer balls by increasing the LC content as well as the functionality of epoxy monomers. Accordingly, the electro-optical properties could be regulated by the morphologies of polymer networks. Especially, the as-made PDLC films with homogeneous porous structures exhibited the optimal electro-optical properties. Consequently, this work offers a meaningful approach to control the microstructures and optimize the electro-optical properties of PDLC films, which indeed can form a wonderful footstone for the wide application of PDLC.     

Control of the microstructure of polymer network and effects of the microstructures on light scattering properties of UV‐cured polymer‐dispersed liquid crystal films

Polymer‐dispersed liquid crystals (PDLC) films were prepared from ultraviolet (UV) irradiation‐induced polymerization of the photopolymerizable monomers in photopolymerizable monomers/nematic liquid crystal (LC) mixtures. The effects of the composition of the mixtures, the curing temperature, and the UV light intensity on the microstructure of the polymer network in the PDLC films were investigated. Furthermore, the effects of the microstructures on the light scattering properties of the PDLC films in the wavelength region of 300–2500 nm were studied experimentally and theoretically based on the combination of three kinds of classical light scattering theories: the Rayleigh‐Gans (RG) approach, the anomalous diffraction (AD) approach, and the geometrical optics (GO) approach. It was found that the sizes of LC domain in PDLC films increased with the increase of the LC content as well as the decrease of the UV curing intensity, while increased at first and then decreased with the increase of the curing temperature. Moreover, smaller LC domain sizes could exhibit strong scattering properties in a smaller VIS wavelength region and the transmittance in NIR region (especially in the wavelength range of 1300–2500 nm) obviously decreased with the increasing sizes of LC domain. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2090–2099, 2008     

The fabrication of novel optical diffusers based on UV-cured polymer dispersed liquid crystals

Polymer dispersed liquid crystals (PDLCs) with different sizes of the LC droplets are prepared based on the ultraviolet (UV) light curable acrylate monomers/LCs composites to fabricate the optical diffuser films. To acquire light diffusers with high optical performance, the effects of the monomer structure and the UV light intensity on the micro-structure of the PDLC films are studied. Results show that the PDLC films could exhibit a strong light scattering at the premise of maintaining high transmittance in the visible region. As the LC droplets are spherically dispersed in the polymer networks, when the size of LC droplets is about 3.0 μm, the haze can reach 88.5% and the transmittance is nearly 90.0%, which can be used as a bottom diffuser film. While when the size of LC droplets is about 10.0 μm, the haze and transmittance are 39.2% and 90.2%, respectively; hence, it can be a good choice for a top diffuser film. With the advantages of simple preparation, roll-to-roll industrial production and tunable optical properties, it is supported that the films based on UV-cured PDLC films can be applied as outstanding optical diffuser films in the liquid crystal display industry.     

Effects of multiwalled carbon nanotube on holographic polymer dispersed liquid crystal

The morphology and electro‐optical performance of holographic polymer dispersed liquid crystal (HPDLC) were investigated with the addition of multiwalled carbon nanotube (CNT), both pristine and chemically modified one (CNT‐C?C). With the addition of CNT, the diffraction efficiency increased and showed a maximum at 0.6% while nucleation was delayed due to the increased mixture viscosity. Film was driven only with CNT due to the induced local electric field of polymer to overcome the threshold resistance. Among the two types of CNT, chemically modified one gave finer CNT dispersion, lower mixture viscosity, larger liquid crystal (LC) droplet, higher diffraction efficiency, and shorter response time while the pristine CNT decreased the driving voltage. Copyright © 2010 John Wiley & Sons, Ltd.     

Comparative studies of polymer‐dispersed liquid crystal films via a thiol‐ene click reaction

In this work, the thiol‐ene click reaction is employed to fabricate polymer‐dispersed liquid crystal (PDLC) films by photoinitiated polymerization. The PDLC films are prepared by systematic variation of key conditions: variety and content of ‐ene monomer, liquid crystal (LC) content, curing time, and curing light intensity. We find that both the morphologies and electro‐optic properties of these films are adjustable. When increasing the length of alkyl main chain of ‐ene monomers, the driving voltages reduce, but in turn, the contrast ratio decreases. Increasing ‐ene monomer content raises the driving voltages as well as the response time, and the increase of LC content lowers the driving voltages but has a negative effect on the contrast ratio. The changes to the curing conditions (both curing time and UV light intensity) can be used to modify the driving voltages, response time, and contrast ratios of PDLC films. These comparative studies will elucidate new insights in commercial applications of intelligent PDLC films.     

固化条件对聚合物分散液晶膜电光性能的影响

选用聚乙二醇二缩水甘油醚(EGDE)/季戊四醇缩水甘油醚(PERTGE)/1,8-二氨基-3,6-二氧杂辛烷(EDBEA)/向列相液晶(SLC1717)复合体系,在不同的固化条件下,通过热聚合诱导相分离方法制备了一系列电光性能不同的聚合物分散液晶(polymer dispersed liquid crystal,简称PDLC)膜.研究了固化温度和固化时间对制备的PDLC膜中聚合物网络的微观形貌和电光性能的影响.结果表明,随着固化温度的升高以及固化时间的缩短,PDLC膜的对比度、驱动电压和开态响应时间逐渐增大,而关态响应时间逐渐减小.在固化温度为363.2 K,固化时间为7 h时,所制备的PDLC膜具有较佳的电光性能.     

Synthesis and properties of phenyl benzoate-based and biphenyl-based liquid crystalline thiol-ene monomers

Novel phenyl benzoate-based and biphenyl-based liquid crystalline thiol-ene monomers were synthesized and their properties investigated. By varying the bridging unit and spacer length, the type of mesophase can be tuned from the low ordered nematic and smectic A phase in the case of the phenyl benzoate-based monomers, to the highly ordered crystal E phase for the biphenyl-based monomers and their corresponding bromo precursors. We investigated the degree of order of the phenyl benzoate-based materials using the Haller method. Possible premature polymerization of these monomers was examined by size exclusion chromatography. The materials exhibit low transition temperatures and a high stability at typical handling times and temperatures. Consequently, these monomers are useful for in situ polymerization with anisotropic inert solvents, which could potentially lead to new architectures and enhanced electro-optical properties of devices. The use of the biphenyl-based monomers appears to be of limited use for polymerizations in anisotropic solution. However, as a result of their intrinsic high degree of molecular order, these monomers form a particularly interesting class of reactive materials that can be bulk polymerized to give main chain polymers with highly defined mechanical and optical or electro-optical properties.     

Effect of crosslinking polymer networks on the molecular reorientation and electro‐optical performance of in‐plane switching vertically aligned liquid crystal devices

The effects of crosslinking polymer networks (PNs) on the molecular reorientation and electro‐optical properties of vertically aligned (VA) liquid crystal (LC) devices are investigated by applying an in‐plane switching (IPS) electric field. Through the polymerization process, crosslinking PNs are developed on the substrate surface, effectively increasing the anchoring energy and governing the LC molecular reorientation. With its stronger anchoring effect, the PNs cell shows good light transmittance and excellent vertical alignment quality, as compared to the pure LC cell. Furthermore, the alignment transformation and transmittance bounce resulting from the transient process of LC molecular reorientation are eliminated when the cell is operated at high voltages. The rising‐time (t_r) and falling‐time (t_f) responses of the PNs cell are significantly improved, and around 36% improvement in the optical switching response is obtained. In addition, the dynamic gray‐level t_r and t_f responses of the PNs cell are enhanced by around 55% and 42%, respectively, at a low driving voltage (～12 V). This developed VA‐IPS LC/PNs cell benefits not only the LC molecular alignment but also the electro‐optical performance. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1123–1130     

Effects of the fluorinated liquid crystal molecules on the electro-optical properties of polymer dispersed liquid crystal films

The different fluorinated liquid crystal (LC) molecules doped to E8 were used as LC component to prepare polymer dispersed liquid crystal (PDLC) films. The mass fraction of the LC mixture is fixed 50.0 wt%. Results indicate that doping 8.0 wt% fluorinated LC molecule ME3CP to E8 significantly reduced the driving voltage of the PDLC films, and the driving voltage reduced with the rise of mass fraction of ME3CP. Besides, the terminal flexible chain length of the fluorinated LC molecule influenced the LC mixture properties based on E8, such as the dielectric anisotropy, birefringence and viscosity of the LC mixture, and the morphology and the electro-optical properties of PDLC films were controlled not only by the physical properties of the LC mixture, but also by the terminal flexible chain length of the fluorinated LC molecule .     

Effects of hyperbranched prepolymers prepared from butyl acrylate and butyl methacrylate on the electro‐optical properties of polymer dispersed liquid crystal

Two hyperbranched prepolymers were synthesized via the reversible addition‐fragmentation chain transfer copolymerization of butyl acrylate or butyl methacrylate with divinyl benzene, respectively. These prepolymers were used in the photopolymerization‐induced phase separation process of preparing polymer dispersed liquid crystal (PDLC) films with no risk of gelation. The morphologies of PDLC samples were investigated. Of particular interest was that the driving voltage (V₉₀) of PDLC with high glass transition temperature (T_g) matrix was as low as 5 V, whereas the V₉₀ of PDLC with low T_g matrix was still high. An explanation for this phenomenon is the hypothesis that different interaction modes function at the interface of liquid crystal and polymer. Meanwhile, the hysteresis of the two systems was minor, which correlated with the hyperbranched structure of polymer. The on‐state transmittance (T_ON) of PDLC films enhanced because of the well matching between the refractive index of polymer and that of liquid crystal. Copyright © 2011 John Wiley & Sons, Ltd.     

Rough surfaces for orientation control in reverse mode polymer dispersed liquid crystal films

Reverse mode operation shutters have been achieved with polymer dispersed liquid crystals by means of polymerization-induced phase separation of nematic mixtures consisting of a low molecular mass liquid crystal and a liquid crystalline monomer. Fluid mixtures were homeotropically aligned by rough surfaces and transparent films were obtained after polymerization. Transmittance in the OFF state can be larger than 80% and decreases to less than 1% when an electric field of about 2 V μm^-1 at 1 kHz is applied (ON state). Both rise and decay times can be lower than 10 ms and the drop in the OFF state normal transmittance is drastically reduced with respect to conventional polymer dispersed liquid crystals since samples exhibit a reverse morphology. The role played by surface roughness is also discussed.     

The effect of fluorine-substituted acrylate monomers on the electro-optical and morphological properties of polymer dispersed liquid crystals

The effects of fluorinated acrylate monomers on the electro-optical and morphological properties of polymer dispersed liquid crystal (PDLC) films are reported. The partial fluorination of host polymer matrices resulted in improved optical properties and better defined morphologies. An enhancement in contrast ratio was observed for fluorinated systems containing trifluoroethyl acrylate (TFEA) and hexafluoroisopropyl acrylate (HFIPA). Conversely, the incorporation of methyl acrylate (MA), a chemically similar non-fluorinated acrylate, resulted in no appreciable change in contrast ratio and an increase in relaxation time. Scanning electron microscopy morphological studies were conducted to understand further the influence of fluorinated monomers in PDLC systems.     

Effects of the structures of epoxy monomers on the electro-optical properties of heat-cured polymer-dispersed liquid crystal films

Polymer-dispersed liquid crystal (PDLC) films were prepared from thermal polymerisation-induced phase separation in heat-curable monomers/nematic liquid crystal (LC) mixtures. For PDLCs with a certain amount of LCs, the microstructure and the refractive index of polymer networks could be influenced by the relative content of epoxy monomers, owing to their different chemical structures. The effect of these factors on the electro-optic properties of films was also investigated.     

Electro‐optical characteristics in phase separated liquid crystal/photo‐curable acrylic monomer mixture system

One of the main objectives of the experiment was to achieve the vertical aligned (VA) effect. To accomplish this, we employed liquid crystal (LC)/photo‐curable acrylic monomers mixture systems to prepare vertical alignment copolymer film (VACOF) for LC molecules with the photo‐polymerization induce phase separation (PIPS) process. From previous experimental results, we successfully fabricated LC devices without the micro‐protrusion structure. After the application of a saturated voltage, the LC molecules actually exhibited such interesting phenomena as uniaxial orientation, uniform single‐domain display state, etc. In this study, to obtain VACOF with smooth surface, we similarly controlled appropriate experimental conditions such as UV light exposure intensity and curing temperature, and altered process parameters such as the cell thickness, chemical structure length of the main chain type biphenol acrylic monomer [to simulate the main chain function of the traditional vertical alignment type polyimide (PI)], etc. During the experiment, we discovered that regardless of the cell thickness, this photo‐alignment system would yield the VACOF instead of the polymer disperse liquid crystal (PDLC) film morphology. Another notable finding was that the contrast ratio was heavily influenced by the length of the main chain type acrylic monomer structure for LC/monomer mixture systems, with enhancement of up to ～56%. Therefore, we further investigated the display effects, electro‐optical properties, etc. for these two main chain type acrylic monomer systems with different lengths and cell thicknesses. Copyright © 2011 John Wiley & Sons, Ltd.