Preparation and characterization of poly(butylene terephthalate)/poly(ethylene terephthalate) copolymers via solid‐state and melt polymerization

To increase the T_g in combination with a retained crystallization rate, bis(2‐hydroxyethyl)terephthalate (BHET) was incorporated into poly(butylene terephthalate) (PBT) via solid‐state copolymerization (SSP). The incorporated BHET fraction depends on the miscibility of BHET in the amorphous phase of PBT prior to SSP. DSC measurements showed that BHET is only partially miscible. During SSP, the miscible BHET fraction reacts via transesterification reactions with the mobile amorphous PBT segments. The immiscible BHET fraction reacts by self‐condensation, resulting in the formation of poly(ethylene terephthalate) (PET) homopolymer. ¹H‐NMR sequence distribution analysis showed that self‐condensation of BHET proceeded faster than the transesterification with PBT. SAXS measurements showed an increase in the long period with increasing fraction BHET present in the mixtures used for SSP followed by a decrease due to the formation of small PET crystals. DSC confirmed the presence of separate PET crystals. Furthermore, the incorporation of BHET via SSP resulted in PBT‐PET copolymers with an increased T_g compared to PBT. However, these copolymers showed a poorer crystallization behavior. The modified copolymer chain segments are apparently fully miscible with the unmodified PBT chains in the molten state. Consequently, the crystal growth process is retarded resulting in a decreased crystallization rate and crystallinity. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 882–899, 2007.     

Butylene copolyesters based on aldaric and terephthalic acids. Synthesis and characterization

The synthesis, characterization, and some properties of new copolyesters analogous to poly(butylene terephthalate) (PBT), based on L ‐arabinaric and galactaric acids, are described. These copolyesters were obtained by polycondensation reaction in the melt of mixtures of methyl 2,3,4‐tri‐O‐methyl‐L ‐arabinarate or methyl 2,3,4,5‐tetra‐O‐methyl‐galactarate and dimethyl terephthalate with 1,4‐butanediol. Their weight‐average molecular weights ranged between 10,000 and 34,000, with polydispersities ranging from 1.4 to 2.2. The composition of all the copolymers was analyzed by NMR, and was found to have a statistical microstructure. All these copolyesters were thermally stable, with degradation temperatures well above 300 °C. The melting temperature and crystallinity decreased in both series, and the glass transition temperature increased and decreased respectively, for the PBTGa and PBTAr series with increasing amounts of aldaric units in the copolyester chain. Only PBT‐derived copolyesters containing a maximum of 30% aldaric units showed discrete scattering characteristic of crystalline material. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1168–1177, 2009     

Polyesters analogous to PET and PBT based on O‐benzyl ethers of xylitol and L‐arabinitol

The synthesis, characterization, and some properties of new copolyesters of poly(butylene terephthalate) (PBT) and poly(ethylene terephthalate) (PET) based on L ‐arabinitol and xylitol are described. These copolyesters were obtained by polycondensation reaction in the melt of mixtures of 1,4‐butanediol or ethylene glycol and 2,3,4‐tri‐O‐benzyl‐L ‐arabinitol or 2,3,4‐tri‐O‐benzyl‐xylitol with dimethyl terephthalate. Their weight‐average molecular weights ranged between 7000 and 55,000, with polydispersities ranging from 1.4 to 4.7. Copolymers containing 1,4‐butanediol could be analyzed by NMR, and were found to have a statistical microstructure. All these copolyesters were thermally stable, with degradation temperatures well above 300 °C. With increasing amounts of alditol in the copolyester, the melting temperature and crystallinity decreased in both series, and the glass transition temperature increased for the PBT series and decreased for the PET series. Only PBT‐derived copolyesters containing a maximum of 10% alditol units showed discrete scattering characteristic of crystalline material. No substantial differences in either structure or properties were observed between the L ‐arabinitol and xylitol copolyester series. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5167–5179, 2008     

Partially renewable copolyesters prepared from acetalized d‐glucitol by solid‐state modification of poly(butylene terephthalate)

The backbone of poly(butylene terephthalate) (PBT) was modified with 2,4:3,5‐di‐O‐methylene‐D ‐glucitol (Glux) using solid‐state modification (SSM). The obtained copolyesters proved to have a non‐random overall chemical microstructure. The thermal properties of these semicrystalline, block‐like, Glux‐based materials were extraordinary, showing higher melting points, and glass transition temperatures compared with other sugar‐based copolyesters prepared by SSM. These remarkable thermal properties were a direct result of the inherently rigid structure of Glux and the relatively slow randomization of the block‐like chemical microstructure of the Glux‐based copolyesters in the melt. SSM proved to be a versatile tool for preparing partially biobased copolyesters with superior thermal properties. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 164–177     

Morphology of poly(butylene terephthalate)–poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) segmented copolyesters

Segmented copolyesters, namely, poly(butylene terephthalate)–poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) (PBT‐PETIS), were synthesized with the melting transesterification processing in vacuo condition involving bulk polyester produced on a large scale (PBT) and ternary amorphous random copolyester (PETIS). Investigations on the morphology of segmented copolyesters were undertaken. The two‐phase morphology model was confirmed by transmission electron microscopy and dynamic mechanical thermal analysis. One of the phases was composed of crystallizable PBT, and the other was a homogeneous mixture of PETIS and noncrystallizable PBT. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2257–2263, 2003     

Copolyesters based on poly(butylene terephthalate)s containing cyclohexyl groups: synthesis,structure and crystallization

Poly(butylene terephthalate-co-cyclohexylene dimethylene terephthalate) copolymers PBTCT, were synthesized by melt condensation with compositions ranging from 94/08 to 23/77. ¹³C NMR spectroscopy was used to study the microstructure of the copolyesters and was found to be completely random. The melting temperature, crystallization temperature on cooling, enthalpy of melting and crystallization followed an eutectic behaviour. Thermal and x-ray diffraction studies indicated that the copolyesters in all composition could crystallize. The XRD studies further indicated that PBT rich copolyesters in the range 75 to 100% BT, crystallized in the PBT lattice while the copolyesters rich in PCT having 38 to 100% CT, crystallized in the PCT lattice.     

Neopenthyl glycol containing poly(propylene terephthalate)s: structure–properties relationships

Poly(propylene/neopenthyl terephthalate) random copolymers (PPT‐PNT) and poly(neopenthyl terephthalate) (PNT) were synthesized and subjected to molecular characterization. Afterwards, the polyesters were examined by TGA, DSC, andX‐ray. The copolymers, which displayed a good thermal stability, at room temperature appeared as semicrystalline materials: the main effect of copolymerization was a lowering in the amount of crystallinity and a decrease of the melting temperature with respect to homopolymer PPT. XRD measurements allowed the identification of the PPT crystalline structure in all cases. Amorphous samples were obtained after melt quenching, with the exception of PPT‐PNT5, and an increment of T_g as the content of NT units is increased was observed due to the effect of the side methylene groups in the polymeric chain. The Wood equation described well T_g‐composition data. Lastly, the presence of a rigid‐amorphous phase was evidenced in the copolymers, whose amount depended on composition and on thermal treatment. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 170–181, 2008     

A novel aromatic–aliphatic copolyester consisting of poly(1,4‐dioxan‐2‐one) and poly(ethylene‐co‐1,6‐hexene terephthalate): Preparation,thermal, and mechanical properties

A novel multiblock aromatic–aliphatic copolyester poly(ethylene‐co‐1,6‐hexene terephthalate)‐copoly(1,4‐dioxan‐2‐one) (PEHT‐PPDO) was successfully synthesized via the chain‐extension reaction of dihydroxyl teminated poly(ethylene‐co‐hexane terephthalate) (PEHT‐OH) with dihydroxyl teminated poly(1,4‐dioxan‐2‐one) (PPDO‐OH) prepolymers, using toluene‐2,4‐diisocyanate as a chain extender. To produce PEHT‐OH prepolymer with an appropriate melting point which can match the reaction temperature of PEHT‐OH prepolymer with PPDO‐OH prepolymer, 1,6‐hexanediol was used to disturb the regularity of poly(ethylene terephthalate) segments. The chemical structures and molecular weights of PEHT‐PPDO copolymers were characterized by ¹H NMR, FTIR, and GPC. The DSC data showed that PPDO‐OH segments were miscible well with PEHT‐OH segments in amorphous state and that the crystallization of copolyester was predominantly contributed by PPDO segments. The TGA results indicated that the thermal stability of PEHT‐PPDO was improved comparing with PPDO homopolymer. The novel aromatic–aliphatic copolyesters have good mechanical properties and could find applications in the field of biodegradable polymer materials. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2828–2837, 2010     

Poly(ethylene terephthalate) copolymers containing nitroterephthalic units. I. Synthesis and characterization

The synthesis, microstructure, and thermal behavior of a series of poly(ethylene terephthalate) (PET) copolymers containing nitroterephthalic units are described. These novel copolyesters were synthesized by transesterification followed by melt copolycondensation of dimethyl terephthalate and dimethyl nitroterephthalate mixtures with ethylene glycol. The molar ratio of the two comonomers in the feed varied from 95/5 to 25/75. Furthermore, PET and poly(ethylene nitroterephthalate) homopolymers were synthesized with the same method and comparatively studied. Copolyester compositions were practically the same as in the feed, and weight‐average molecular weights ranged from 10,000 to 60,000. The two monomeric units were randomly distributed along the polymer chain, and the experimentally determined average sequence lengths were in accordance with ideal copolycondensation statistics. Melting temperatures and enthalpies of the copolyesters decreased with increasing content in nitroterephthalic units, and they all showed a single glass‐transition temperature superior to that of PET. They appeared to be stable up to 300 °C, and thermal degradation occurred in two well‐differentiated steps. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3761–3770, 2000     

Poly(ethylene terephthalate) copolymers containing 5‐nitroisophthalic units. I. Synthesis and characterization

Poly(ethylene terephthalate‐co‐5‐nitroisophthalate) copolymers, abbreviated as PETNI, were synthesized via a two‐step melt copolycondensation of bis(2‐hydroxyethyl) terephthalate and bis(2‐hydroxyethyl) 5‐nitroisophthalate mixtures with molar ratios of these two comonomers varying from 95/5 to 50/50. Polymerization reactions were carried out at temperatures between 200 and 270 °C in the presence of tetrabutyl titanate as a catalyst. The copolyesters were characterized by solution viscosity, GPC, FTIR, and NMR spectroscopy. They were found to be random copolymers and to have a comonomer composition in accordance with that used in the corresponding feed. The copolyesters became less crystalline and showed a steady decay in the melting temperature as the content in 5‐nitroisophthalic units increased. They all showed glass‐transition temperatures superior to that of PET with the maximum value at 85 °C being observed for the 50/50 composition. PETNI copolyesters appeared stable up to 300 °C and thermal degradation was found to occur in two well‐differentiated steps. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1934–1942, 2000     

Synthesis of high‐molecular‐weight aliphatic–aromatic copolyesters from poly(ethylene‐co‐1,6‐hexene terephthalate) and poly(L‐lactic acid) by chain extension

A series of aliphatic–aromatic multiblock copolyesters consisting of poly(ethylene‐co‐1,6‐hexene terephthalate) (PEHT) and poly(L ‐lactic acid) (PLLA) were synthesized successfully by chain‐extension reaction of dihydroxyl terminated PEHT‐OH prepolymer and dihydroxyl terminated PLLA‐OH prepolymer using toluene‐2,4‐diisoyanate as a chain extender. PEHT‐OH prepolymers were prepared by two step reactions using dimethyl terephthalate, ethylene glycol, and 1,6‐hexanediol as raw materials. PLLA‐OH prepolymers were prepared by direct polycondensation of L ‐lactic acid in the presence of 1,4‐butanediol. The chemical structures, the molecular weights and the thermal properties of PEHT‐OH, PLLA‐OH prepolymers, and PEHT‐PLLA copolymers were characterized by FTIR, ¹H NMR, GPC, TG, and DSC. This synthetic method has been proved to be very efficient for the synthesis of high‐molecular‐weight copolyesters (say, higher than M_w = 3 × 10⁵ g/mol). Only one glass transition temperature was found in the DSC curves of PEHT‐PLLA copolymers, indicating that the PLLA and PEHT segments had good miscibility. TG curves showed that all the copolyesters had good thermal stabilities. The resulting novel aromatic–aliphatic copolyesters are expected to find a potential application in the area of biodegradable polymer materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5898–5907, 2009     

Melting and crystallization of poly(butylene terephthalate) by temperature‐modulated and superfast calorimetry

Quantitative temperature‐modulated differential scanning calorimetry (TMDSC) and superfast thin‐film chip calorimetry (SFCC) are applied to poly(butylene terephthalate)s (PBT) of different thermal histories. The data are compared with those of earlier measured heat capacities of semicrystalline PBT by adiabatic calorimetry and standard DSC. The solid and liquid heat capacities, which were linked to the vibrational and conformational molecular motion, serve as references for the quantitative analyses. Using TMDSC, the thermodynamic and kinetic responses are separated between glass and melting temperature. The changes in crystallinity are evaluated, along with the mobile–amorphous and rigid–amorphous fractions with glass transitions centered at 314 and 375 K. The SFCC showed a surprising bimodal change in crystallization rates with temperature, which stretches down to 300 K. The earlier reported thermal activity at about 248 K was followed by SFCC and TMDSC and could be shown to be an irreversible endotherm and is not caused by a glass transition and rigid–amorphous fraction, as assumed earlier. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1364–1377, 2006     

Modifying an amorphous polymer to a fast crystallizing semi‐crystalline material by copolymerization with monodisperse amide segments

Segmented block copolymers of polysulphone with monodisperse amide segments were synthesized by a melt and a solution polymerization method. Both triblock and multiblock copolymers were prepared. The length of the difunctional polysulphone was varied from 2000 to 20,000 g/mol. The monodisperse amide segment was the tetra‐amide T6T6T based on terephthalic acid (T) and hexamethylene diamine (6) units. The main goal of this work was to study if the high T_g amorphous polysulphone could be modified to a high T_g semi‐crystalline PSU‐T6T6T copolymer. The copolymers were characterized by viscosity measurements, NMR, FTIR, MALDI‐TOF, DSC, and DMA. Depending on the amide concentration in the copolymers the T6T6T melting temperatures ranged between 220 and 270 °C and thus the crystallization window was small 50–100 °C. From the FTIR results, it was revealed that the crystallinity of the T6T6T segments in the copolymer could be very high, up to 92–97%. The T6T6T has crystallized out into nanoribbons with a high aspect ratio. These high T_g semi‐crystalline copolymers had a high dimensional and solvent resistance. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 63–73, 2010     

Photoinduced thiol–ene crosslinking of globalide/ε‐caprolactone copolymers: Curing performance and resulting thermoset properties

The increasing demand for bioderived polymers led us to investigate the potential use of the macrolactone globalide in thermoset synthesis via the photoinduced thiol–ene reaction. A series of six lipase‐catalyzed poly(globalide‐caprolactone) copolyesters bearing internal main‐chain unsaturations ranging from 10 to 50 and 100 mol % were successfully crosslinked in the melt with equal amounts of thiol groups from trimethylolpropane‐trimercapto propionate affording fully transparent amorphous elastomeric materials with different thermal and viscoelastic properties. Three major conclusions can be drawn from this study: (i) high thiol–ene conversions (>80%) were easily attained for all cases, while maintaining the cure behavior, and irrespective of functionality at reasonable reaction rates; (ii) parallel chain‐growth homopropagation of the ene monomer is insignificant when compared with the main thiol–ene coupling route; and (iii) high ene‐density copolymers result in much lower extracted sol fractions and high T_g values as a result of a more dense and homogeneous crosslinked network. The thiol–ene system evaluated in this contribution serve as model example for the sustainable use of naturally occurring 1,2‐disubstituted alkenes in making semisynthetic polymeric materials in high conversions with a range of properties. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012.     

Butadiene–isoprene copolymerization with V(acac)3‐MAO. Crystalline and amorphous trans‐1,4 copolymers

Butadiene‐isoprene copolymerization with the system V(acac)₃‐MAO was examined. Crystalline or amorphous copolymers were obtained depending on isoprene content. Both butadiene and isoprene units exhibit a trans‐1,4 structure and are statistically distributed along the polymer chain. Polymer microstructure, comonomer composition, and distribution along the polymer chain were determined by ¹³C and ¹H NMR analysis. The thermal and X‐ray behaviors of the copolymers were also investigated and compared with results from solid‐state ¹³C NMR experiments. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4635–4646, 2007     

Facile synthesis of graft copolymers containing rigid poly(dialkyl fumarate) branches by macromonomer method

Graft copolymers show microphase separated structure as seen in block copolymers and have lower intrinsic viscosity than block copolymers because of a branching structure. Therefore, considering molding processability, especially for polymers containing rigid segments, graft copolymers are useful architectures. In this work, graft copolymers containing rigid poly(diisopropyl fumarate) (PDiPF) branches were synthesized by full free‐radical polymerization process. First, synthesis of PDiPF macromonomers by addition‐fragmentation chain transfer (AFCT) was investigated. 2,2‐Dimethyl‐4‐methylene‐pentanedioic acid dimethyl ester was found to be an efficient AFCT agent for diisopropyl fumarate (DiPF) polymerization because of the suppression of undesired primary radical termination, which significantly took place when common AFCT agent, methyl 2‐(bromomethyl)acrylate, was used. Copolymerization of PDiPF macromonomer with ethyl acrylate accomplished the generation of the graft copolymer having flexible poly(ethyl acrylate) backbone and rigid PDiPF branches. The graft copolymer showed a microphase separated structure, high transparency, and characteristic thermal properties to PDiPF and poly(ethyl acrylate). © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2474–2480     

Synthesis and characterization of fully biobased poly(propylene succinate‐ran‐propylene adipate). Analysis of the architecture‐dependent physicochemical behavior

Fully biobased aliphatic random poly(1,3‐propylene succinate‐ran‐1,3‐propylene adipate) (PPSA) copolyesters with high molar mass were synthesized with different macromolecular architectures based on various succinic acid/adipic acid (SA/AA) molar ratio, by transesterification in melt. Titanium (IV) isopropoxide was used as an effective catalyst. All synthesized copolyesters were fully characterized by different chemical and physicochemical techniques including NMR, size exclusion chromatography, FTIR, wide angle X‐ray scattering, differential scanning calorimetry, and thermogravimetric analysis. The final copolyesters molar compositions were identical to the feed ones. The different sequences based on succinate and adipate segments were randomly distributed along the chains. All the corresponding copolyesters showed an excellent thermal stability with a degradation onset temperature higher than 290 °C, which increased with the adipate content. According to their compositions and architectures, PPSA copolyesters can exhibit or not a crystalline phase, at room temperature. T_g of copolyesters decreased with the adipate content due to the decrease in the chains mobility, following the Gordon–Taylor relation. PPSA showed a pseudo eutectic melting behavior characteristic of an isodimorphic character. Finally, PPSA copolyesters were not able to crystallize during the cooling or the second heating run, due to the 1,3‐propanediol chemical structure, which led to amorphous materials with the exception of the polyester based solely on AA. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2738–2748     

Poly(ethylene terephthalate) copolymers containing 5‐nitroisophthalic units. III. Methanolytic degradation

The methanolysis of poly(ethylene terephthalate) (PET) copolymers containing 5‐nitroisophthalic units was investigated. Random copolyesters containing 10 and 30 mol % of such units were prepared via a two‐step melt copolycondensation of bis(2‐hydroxyethyl) terephthalate (BHET) and bis(2‐hydroxyethyl) 5‐nitroisophthalate (BHENI) in the presence of tetrabutyl titanate as a catalyst. First, the susceptibility of these two comonomers toward methanolysis was evaluated, and their reaction rates were estimated with high‐performance liquid chromatography. BHENI appeared to be much more reactive than both BHET and bis(2‐hydroxyethyl) isophthalate. The methanolysis of PET and the copolyesters was carried out at 100 °C, and the degradation process was followed by changes in the weight and viscosity, gel permeation chromatography, differential scanning calorimetry, and ¹H and ¹³C NMR spectroscopy. The copolyesters degraded faster than PET, and the rate of degradation increased with the content of nitrated units. The products resulting from methanolysis were concluded to be dimethyl terephthalate, dimethyl 5‐nitroisophthalate, ethylene glycol, and small, soluble oligomers. For both PET and the copolyesters, an increase in crystallinity was observed during the degradation process, indicating that methanolysis preferentially occurred in the amorphous phase. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 76–87, 2002     

Crystallization behavior and morphology of poly(ethylene‐co‐trimethylene terephthalate)s

The melt crystallization behaviors and crystalline structures of poly(ethylene terephthalate) (PET), poly(trimethylene terephthalate), and poly(ethylene‐co‐trimethylene terephthalate) (PETT) were investigated with differential scanning calorimetry (DSC), polarized optical microscopy (POM), and X‐ray diffraction at various crystallization temperatures (T_cs). The PETT copolymers were synthesized via the polycondensation of terephthalate with ethylene glycol and trimethylene glycol (TG) in various compositions. The copolymers with 69.0 mol % or more TG or 31.0 mol % or less TG were crystallizable, but the other copolymers containing 34–56 mol % TG were amorphous. The DSC isothermal results revealed that the addition of a small amount of flexible TG (up to 21 mol %) to the PET structure slightly reduced the formation of three‐dimensional spherulites. A greater TG concentration (91–100%) in the copolyesters changed the crystal growth from two‐dimensional to three‐dimensional. The DSC heating scans after the completion of isothermal crystallization at various T_cs showed three melting endotherms for PET, PETT‐88, PETT‐84, and PETT‐79 and four melting endotherms for PETT‐9 and PETT. The presence of an additional melting endotherm could be attributed to the melting of thinner and imperfect copolyester crystallites. Analyses of the Lauritzen–Hoffman equation demonstrated that PETT‐88 had the highest values of the product of the lateral and folding surface free energies, and this suggested that the addition of small amounts of flexible trimethylene terephthalate segments to PET disturbed chain regularity, thus increasing molecular chain mobility. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4255–4271, 2004     

Oxidative copolymerization of 2‐pyridylamine and aniline

A series of copolymers were easily synthesized via the chemical oxidative polymerization of 2‐pyridylamine (2PA) and aniline (AN) in an acidic aqueous medium. The yield, intrinsic viscosity, and solubility of the copolymers were studied through changes in the 2PA/AN molar ratio, polymerization temperature, oxidant, oxidant/monomer molar ratio, and polymerization medium. The resulting 2PA/AN copolymers were characterized by ¹H NMR, Fourier transform infrared, wide‐angle X‐ray diffraction, and thermogravimetric techniques. The results showed that the oxidative copolymerization from 2PA and AN was exothermic. The resultant copolymers were amorphous and exhibited enhanced solubility in comparison with polyaniline. The 2PA/AN copolymers showed the highest decomposition temperature (530 °C), the slowest maximum‐weight‐loss rate (1.2 %/min), the largest char yield (45 wt %), and the greatest degradation activation energy (65 kJ/mol) in nitrogen. The thermostability of the copolymers was generally higher in nitrogen than in air. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4407–4418, 2000