Hyperbranched copolyfluorene from a 2,4,7‐trifunctional fluorene monomer

A new hyperbranched ( P1 ) and linear copolyfluorene ( P2 ) were prepared from 2,4,7‐trifunctional (branching) and 2,7‐bifunctional fluorene monomer, respectively, by the Wittig reaction, followed with end‐capping by aromatic oxadiazole groups, to study the effect of hyperbranch structure. The weight‐average molecular weights (M_w) of P1 and P2 , determined by gel permeation chromatography using polystyrene as standard, were 33,000 and 25,700, respectively. The polymers were readily soluble in common organic solvents and exhibited good thermal stability (T_d > 400 °C). Optical properties, both in solution and film state, were investigated using absorption and photoluminescence (PL) spectra. In film state, the absorption and PL spectra peaked at 401–425 nm and 480–495 nm, respectively. The P1 showed energy funnel effect and enhanced fluorescence efficiency owing to hyperbranched structure and terminal oxadiazole groups. The HOMO and LUMO levels of P1 ( P2) , estimated from cyclic voltammograms, are ?5.34 (?5.25) eV and ?2.94 (?2.94) eV, respectively. Two‐layer polymer light‐emitting diodes devices (ITO/PEDOT/ P1 /Ca/Al) exhibited maximal luminance and luminous efficiency of 3630 cd/m² and 0.78 cd/A, respectively, which are superior to its linear counterpart P2 (598 cd/m², 0.11 cd/A). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5541–5551, 2007     

Hyperbranched framework of interrupted π‐conjugated polymers end‐capped with high carrier‐mobility moieties for stable light‐emitting materials with low driving voltage

A novel series of soluble hyperbranched interrupted π‐conjugated polymers (HICPs) based on complicated 9,9‐diarylfluorenes (CDAFs) branching core and end‐capped with high carrier‐mobility pyrene moieties were synthesized via the “A₂ + A′₂ + B₃” type Suzuki coupling condensation. The new polymer architecture improves the spectrum stability than the corresponding linear and hyperbranched polymers in PLEDs. Besides, it overcomes the drawback of high driving voltage of common interrupted π‐conjugated polymers. CDAF1 exhibits excellent thermal and morphological stability with a decomposition temperature (T_d) higher than 445 °C and a glass transition temperature (T_g) up to 128 °C. No obvious low‐energy green emission band at 520 nm was observed under extreme thermal annealing conditions in air at 200 °C for 12 h. The CDAF1 device shows stable blue emission with the peak at 422 and 447 nm. The Commission International d'Eclairage (CIE) 1931 coordinates is (0.18, 0.16) and the brightness reaches 1051 cd/m² at 15.7 V. White PLED based on CDAF1/MEH‐PPV blends exhibits a low turn‐on voltage of 4.8 V with voltage‐independent CIE of (0.32, 0.32). Molecular simulations were used to investigate the conformation and interchain interaction. HICPs based on CDAFs tethered with high‐mobility moieties are promising stable blue and host materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6451–6462, 2009     

Solution‐processable and thermally cross‐linkable fluorene‐cored triple‐triphenylamines with terminal vinyl groups to enhance electroluminescence of MEH‐PPV: Synthesis,curing, and optoelectronic properties

This study reports the synthesis, curing, and optoelectronic properties of a solution‐processable, thermally cross‐linkable electron‐ and hole‐blocking material containing fluorene‐core and three periphery N‐phenyl‐N‐(4‐vinylphenyl)benzeneamine ( FTV ). The FTV exhibited good thermal stability with T_d above 478 °C in nitrogen atmosphere. The FTV is readily cross‐linked via terminal vinyl groups by heating at 160 °C for 30 min to obtain homogeneous film with excellent solvent resistance. Multilayer PLED device [ITO/PEDOT:PSS/cured‐ FTV /MEH‐PPV/Ca (50 nm)/Al (100 nm)] was successfully fabricated using solution processed. Inserting cured‐ FTV is between PEDOT:PSS and MEH‐PPV results in simultaneous reduction in hole injection from PEDOT:PSS to MEH‐PPV and blocking in electron transport from MEH‐PPV to anode. The maximum luminance and maximum current efficiency were enhanced from 1810 and 0.27 to 4640 cd/m² and 1.08 cd/A, respectively, after inserting cured‐ FTV layer. Current results demonstrate that the thermally cross‐linkable FTV enhances not only device efficiency but also film homogeneity after thermal curing. FTV is a promising electron‐ and hole‐blocking material applicable for the fabrication of multilayer PLEDs based on PPV derivatives. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 000: 000–000, 2012     

Novel Spectrally Stable Saturated Blue‐Light‐Emitting Poly[(fluorene)‐co‐(dioctyldibenzothiophene‐S,S‐dioxide)]s

Novel poly[(fluorene)‐co‐(2,8‐dioctyldibenzothiophene‐S,S‐dioxide‐3,7‐diyl)]s were synthesized. The octyl group on the 2,8‐dioctyldibenzothiophene‐S,S‐dioxide (DOSO) unit improved the solubility of the polymers and broadened the optical band gap from 2.95 to 3.20 eV as the content of DOSO unit increases. The electroluminescence (EL) spectra of polymers show CIE coordinates around (0.16, 0.07) independent of the ratio of DOSO units in the polymers, owing to the ICT and steric hindrance dual‐function. A high efficiency of 3.1 cd · A⁻¹ (EQE = 3.9%) was obtained with the configuration of ITO/PEDOT:PSS/polymer/Ba/Al. The results indicate that PF‐3,7DOSOs could be a promising candidate for saturated blue‐emitting polymers with spectral stability and high efficiency.

     

Luminescent copolyethers containing isolated 1,4‐distyrylbenzene derivatives backbone and 7‐oxy‐4‐methylcoumarin side group: Synthesis and characterization

Four new copolyethers ( P1 – P4 ) consisting of two isolated emitting chromophores [2,5‐dihexyloxy‐1,4‐distyrylbenzene (HODSB) and 2,5‐dihexyloxy‐1,4‐di(4‐methylenestyryl)benzene (HOMDSB) for P1 and P2 , 2,5‐dihexyl‐1,4‐distyrylbenzene (HDSB) and HOMDSB for P3 and P4 ] in the backbone, in which P2 and P4 further contain electron‐transporting chromophores [7‐oxy‐4‐methylcoumarin (OMC)] in the side chain, were successfully prepared by the Heck coupling reaction. The photoluminescence spectra and quantum yields of the copolymers depended mainly on compositions of the isolated fluorophores. Their highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels were estimated from their cyclic voltammograms. Electrochemical investigations proved that the oxidation started at hole‐transporting DSB segments, whereas reduction began at electron‐transporting OMC groups in P2 and P4 . The electron affinity of P2 and P4 was enhanced by introducing electron‐transporting OMC chromophores. Double‐layer light‐emitting diodes (ITO/PEDOT:PSS / polymer/Al) of P1 and P2 revealed green electroluminescence, and those of P3 and P4 emitted blue light. Moreover, incorporation of OMC side groups effectively reduced turn‐on electric field and enhanced luminance efficiency of the EL devices due to increased electron affinity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 211–221, 2007     

Alkyl side chain driven tunable red–yellow–green emission: Investigation on the new π‐conjugated polymers comprising of 2,7‐carbazole unit and 2,1,3‐benzo‐thiadiazole units with different side chains

Four new soluble polymers containing a 2,7‐carbazole unit and a 2,1,3‐benzothiadiazole unit in the main chain were synthesized by Suzuki polycondensation. Variation of the substituent groups (R) at 5‐position of 2,1,3‐benzothiadiazole unit resulted in different color emission of the copolymers. Thus, when R was ? CH₃ (or ? H), the polymer showed yellow–green (or red) emission; whereas the polymers showed the emission from green to yellow–green, when R was ? CH₂(CH₂)₅CH₃ or ? CH₂OCH(CH₃)₂. To investigate the nature of the color change, a Gaussian 03 program was used for estimation of the dihedral angles between a 5‐R‐2,1,3‐benzothiadiazole unit and a 2,7‐carbazole unit. The results showed that the different substituents at 5‐position of 2,1,3‐benzothiadiazole brought about different the dihedral angles, which gave the different conjugation levels to the polymers. Hence, the tunablity of emission color may be attributed to the different conjugation levels between 2,7‐carbazole units and 5‐R‐2,1,3‐benzothiadiazole units induced by simply changing substituent groups at 5‐position of benzothiadiazole unit. Electrochemically, the copolymers exhibited a higher oxidation potential as well as the reversible reduction behavior bearing from 2,1,3‐benzothiadiazole unit. To investigate the electroluminescent properties of the polymers, the nonoptimized devices were fabricated and the results showed that the electroluminescent emission wavelength was basically similar to that of the photoluminescent. All polymers showed good thermal stability with 5 wt % loss temperature of more than 296 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1376–1387, 2008     

Luminescent copoly(aryl ether)s with new electron‐transporting bis(3‐(trifluoromethyl)phenyl)‐1,3,4‐oxadiazole or bis(3‐(trifluoromethyl)phenyl)‐4‐(4‐hexyloxyphenyl)‐4H‐1,2,4‐triazole segments

To investigate the effect of trifluoromethyl groups in enhancing electron affinity of aromatic oxadiazole and triazole chromophores, we prepared four new copoly(aryl ether)s ( P1 – P4 ) consisting of bis(3‐(trifluoromethyl) phenyl)‐1,3,4‐oxadiazole (ETO) or bis(3‐(trifluoromethyl)phenyl)‐4‐(4‐hexyloxyphenyl)‐4H‐1,2,4‐triazole (ETT) segments and hole‐transporting segments [2,5‐distyrylbenzene (HTB) or bis(styryl)fluorine (HTF)]. Molecular spectra (absorption and photoluminescence) and cyclic voltammetry were used to investigate their optical and electrochemical properties. The emissions of P1 – P4 are dominated by the hole‐transporting fluorophores with longer emissive wavelengths around 442–453 nm via efficient excitation energy transfer. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of P1 – P4 , estimated from electrochemical data, are ?5.15, ?5.18, ?5.30, ?5.27, ?3.39, ?3.49, ?3.36, and ?3.48 eV, respectively. The LUMO levels of ETO and ETT segments are significantly reduced to ?3.39～?3.36 eV and ?3.48～?3.49 eV, respectively, as compared with ?2.45 eV of P5 containing a 2,5‐diphenyl‐1,3,4‐oxadiazole segment. Moreover, electron and hole affinity can be enhanced simultaneously by introducing isolated hole‐ and electron‐transporting segments in the backbone. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5900–5910, 2004     

Synthesis of electroluminescent copoly(aryl ether)s containing alternate 1,4‐distyrylbenzene derivatives and aromatic 1,3,4‐oxadiazole or 3,3″‐terphenyldicarbonitrile segments

New copoly(aryl ether)s ( P1 – P3 ) containing alternate 2,5‐dihexyloxy‐1,4‐di(m‐ethoxystyryl)benzene ( P1 , P2 ) or 2,5‐dihexyloxy‐1,4‐distyrylbenzene ( P3 ) chromophores and aromatic 1,3,4‐oxadiazole ( P1 ) or 3,3″‐terphenyldicarbonitrile ( P2 , P3 ) segments were prepared by Horner reaction ( P1 and P2 ) or nucleophilic displacement reaction ( P3 ). They are basically amorphous materials with 5% weight‐loss temperature above 410 °C. Their absorption, photoluminescence spectra, and quantum yields are dependent on the composition of the isolated fluorophores. The emissions are exclusively dominated by 1,4‐distyrylbenzene segments via excitation energy transfer from electron‐transporting 1,3,4‐oxadiazole ( P1 ) or 3,3″‐terphenyldicarbonitrile ( P2 , P3 ) chromophores. The HOMO and LUMO energy levels have been estimated from their cyclic voltammograms, and the observations confirm that oxidation and reduction start from the emitting 1,4‐distyrylbenzene and electron‐transporting segments, respectively, indicating that both carriers affinity can be enhanced simultaneously. Among the two‐layer PLED devices (ITO/PEDOT/ P1 – P3 /Al), P1 exhibits the best performance with a turn‐on field of 4 × 10⁵ V/cm and a maximum luminance of 225 cd/m². However, P2 emits green–yellow light (555 nm), owing to the excimer emission. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5009–5022, 2005     

Synthesis and properties of new orange red light‐emitting hyperbranched and linear polymers derived from 3,5‐dicyano‐2,4,6‐tristyrylpyridine

Two new orange red light‐emitting hyperbranched and linear polymers, poly(pyridine phenylene)s P1 and P2, were prepared by the Heck coupling reaction. In particular, an A₂ + B₃ approach was developed to synthesize conjugated hyperbranched polymer P2 via one‐pot polycondensation. The polymers were characterized by NMR, Fourier transform infrared, ultraviolet–visible, and elemental analysis. They showed excellent solubility in common solvents such as tetrahydrofuran, CH₂Cl₂, CHCl₃, and N,N‐dimethylformamide and had high molecular weights (up to 6.1 × 10⁵ and 5.8 × 10⁵). Cyclic voltammetry studies revealed that P2 had a low‐lying lowest unoccupied molecular orbital energy level of ?3.22 eV and a highest occupied molecular orbital energy level of ?5.43 eV. The thin film of P2 emitted strong orange‐red photoluminescence at 595 nm. A double‐layer light‐emitting diode fabricated with the configuration of indium tin oxide/P2/tris(8‐hydroxy‐quinoline)aluminum/Al emitted orange‐red light at 599 nm, with a brightness of 662 cd/m² at 7 V and a turn‐on voltage of 4.0 V; its external quantum efficiency was calculated to be 0.19% at 130.61 mA/cm². This indicated that this new electroluminescent polymer (P2) based on 3,5‐dicyano‐2,4,6‐tristyrylpyridine could possibly be used as an orange‐red emitter in polymer light‐emitting displays. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 493–504, 2005     

Synthesis and opto‐electrical properties of dendron‐containing poly(2,3‐diphenyl‐1,4‐phenylenevinylene) derivatives

A new series of poly(2,3‐diphenyl‐1,4‐phenylenevinylene) derivatives containing dendritic side groups were synthesized. Different generations of dendrons were integrated on the pendant phenyl ring to investigate their effect on optical and electrical properties of final polymers. Homopolymers can not be obtained via the Gilch polymerization because of sterically bulky dendrons. By controlling the feed ratio of different monomers during polymerization, dendron‐containing copolymers with high molecular weights were obtained. The UV–vis absorption and photoluminescent spectra of the thin films are pretty close; however, quantum efficiency is significantly enhanced with increasing the generation of dendrons. The electrochemical analysis reveals that hole‐injection is also improved by increasing dendritic generation. Double‐layer light‐emitting devices with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al were fabricated. High generation dendrons bring benefit of improved device performance. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3440–3450, 2007     

Synthesis and characterization of highly stable blue‐light‐emitting hyperbranched conjugated polymers

Polyfluorene homopolymer ( P1 ) and its carbazole derivatives ( P2 – P4 ) have been prepared with good yield by Suzuki coupling polymerization. P2 is an alternating copolymer based on fluorene and carbazole; P3 is a hyperbranched polymer with carbazole derivative as the core and polyfluorene as the long arms; P4 is a hyperbranched polymer with carbazole derivative as the core and the alternating fluorene and carbazole as the long arms. These polymers show highly thermal stability, and their structures and physical properties are studied using gel permeation chromatography, ¹H NMR, ¹³C NMR, elemental analysis, Fourier transform infrared spectroscopy, thermogravimetry, UV–vis absorption, photoluminescence, and cyclic voltammetry (CV). The influence of the incorporation of carbazole and the hyperbranched structures on the thermal, electrochemical, and electroluminescent properties has been investigated. Both carbazole addition and the hyperbranched structure increase the thermal and photoluminescent stability. The CV shows an increase of the HOMO energy levels for the derivatives, compared with polyfluorene homopolymer ( P1 ). The EL devices fabricated by these polymers exhibit pure blue‐light‐emitting with negligible low‐energy emission bands, indicating that the hyperbranched structure has a strong effect on the PLED characteristics. The results imply that incorporating carbazole into polyfluorene to form a hyperbranched structure is an efficient way to obtain highly stable blue‐light‐emitting conjugated polymers, and it is possible to adjust the property of light‐emitting polymers by the amount of carbazole derivative incorporated into the polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 790–802, 2008     

Versatile preparation of poly(1,4‐phenylenevinylene‐co‐1,4‐phenylene‐1,2‐ethanediyl) by CVD polymerization of p‐(methoxymethyl)benzyl chloride

It was demonstrated that a series of copolymers consisting of 1,4‐phenylenevinylene (PV) and 1,4‐phenylene‐1,2‐ethanediyl (PE) units could be prepared from a single monomer, p‐(methoxymethyl)benzyl chloride, via the chemical vapor deposition polymerization (CVDP) method. The composition of the copolymers could be varied simply by altering the monomer activation temperature. The higher the temperature, the lower the content of the PV unit. The photo (PL)‐ and electroluminescence (EL) properties of the copolymers that revealed a blueshift when compared with PPV strongly depend on the amount of the PE units incorporated. The external quantum efficiencies of the electroluminescence devices having the configuration of ITO/PEDOT‐PSS/copolymer/Al‐Li were higher than that of PPV, which can be ascribed to the improved confinement of excitons. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 742–751, 2005     

Hyperbranched luminescent polyfluorenes containing aromatic triazole branching units

Using a new aromatic 1,2,4‐triazole branching monomer (4.8–13.3 mol %), three hyperbranched polyfluorenes ( P2 – P4 ) were synthesized by the Suzuki coupling reaction to investigate the structural effect on optoelectronic properties. Poly(9,9‐dihexylfluorene) ( P1 ) was also prepared for comparative investigation. Their weight‐average molecular weights and polydispersity indices are in the range of 1.16 × 10⁴ to 5.9 × 10⁴ and 1.49–2.25, respectively. Optical properties, both in solution and film state, were investigated using absorption and photoluminescence (PL) spectra. In film state, the absorption and PL spectra peaked at 377–392 and 424–425 nm, respectively, blue‐shift with increasing triazole concentration. Furthermore, a linear relationship between 1/λ_max,abs and 1/(1 ? n_triazole) is correlated (n: molar fraction), indicating a smooth decrease in conjugation length by incorporation of the branch unit. The P4 containing 13.3 mol % triazole reveals stable blue emission even at 150 °C (in air). The HOMO and LUMO levels of P2 – P4 , estimated from cyclic voltammograms, are ?5.69, ?5.73, ?5.78 eV and ?2.63, ?2.64, ?2.63 eV, respectively. The maximal brightness (current efficiency) of the electroluminescent devices (ITO/PEDOT:PSS/ P2 – P4 /Ca/Al) improves from 828 cd/m² (0.19 cd/A) to 2054 cd/m² (0.46 cd/A) with increasing triazole concentration. The results suggest that incorporation of aromatic 1,2,4‐triazole branch units is an effective way to improve annealing stability and EL performance of polyfluorenes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4465–4476, 2007     

Green‐emitting poly[(1,3‐phenylenevinylene)‐alt‐ (1,4‐phenylenevinylene)]s: Effect of the substitution patterns on the optical properties

Green‐emitting substituted poly[(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene)‐alt‐(2,5‐dihexyloxy‐1,4‐phenylenevinylene)]s ( 6 ) were synthesized via the Wittig–Horner reaction. The polymers were yellow resins with molecular weights of 10,600. The ultraviolet–visible (UV–vis) absorption of 6 (λ_max = 332 or 415 nm) was about 30 nm redshifted from that of poly[(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene)‐alt‐(1,4‐phenylenevinylene)] ( 2 ) but was only 5 nm redshifted with respect to that of poly[(1,3‐phenylenevinylene)‐alt‐(2,5‐dihexyloxy‐1,4‐phenylenevinylene)] ( 1 ). A comparison of the optical properties of 1 , 2 , and 6 showed that substitution on m‐ or p‐phenylene could slightly affect their energy gap and luminescence efficiency, thereby fine‐tuning the optical properties of the poly[(m‐phenylene vinylene)‐alt‐(p‐phenylene vinylene)] materials. The vibronic structures were assigned with the aid of low‐temperature UV–vis and fluorescence spectroscopy. Light‐emitting‐diode devices with 6 produced a green electroluminescence output (emission λ_max ～ 533 nm) with an external quantum efficiency of 0.32%. Substitution at m‐phenylene appeared to be effective in perturbing the charge‐injection process in LED devices. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1820–1829, 2004     

Synthesis and optoelectronic properties of luminescent poly(p‐phenylenevinylene) derivatives containing electron‐transporting 1,3,4‐oxadiazole groups

Three random copolymers ( P1–P3 ) comprising phenylenevinylene and electron‐transporting aromatic 1,3,4‐oxadiazole segments (11, 18, 28 mol %, respectively) were prepared by Gilch polymerization to investigate the influence of oxadiazole content on their photophysical, electrochemical, and electroluminescent properties. For comparative study, homopolymer poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐p‐phenylenevinylene] ( P0 ) was also prepared by the same process. The polymers ( P0–P3 ) are soluble in common organic solvents and thermally stable up to 410 °C under a nitrogen atmosphere. Their optical properties were investigated by absorption and photoluminescence spectroscopy. The optical results reveal that the aromatic 1,3,4‐oxadiazole chromophores in P1–P3 suppress the intermolecular interactions. The HOMO and LUMO levels of these polymers were estimated from their cyclic voltammograms. The HOMO levels of P0–P3 are very similar (?5.02 to ?5.03 eV), whereas their LUMO levels decrease readily with increasing oxadiazole content (?2.7, ?3.08, ?3.11, and ?3.19 eV, respectively). Therefore, the electron affinity of the poly(p‐phenylenevinylene) chain can be gradually enhanced by incorporating 1,3,4‐oxadiazole segments. Among the polymers, P1 (11 mol % 1,3,4‐oxadiazole) shows the best EL performance (maximal luminance: 3490 cd/m², maximal current efficiency: 0.1 cd/A). Further increase in oxadiazole content results in micro‐phase separation that leads to performance deterioration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4377–4388, 2007     

Pyrene‐functionalized oligofluorenes as non‐doped deep blue emitters for solution‐processed organic light‐emitting diodes

Two pyrene‐functionalized oligofluorenes (TPA‐PyF₃ and CBP‐PyF₃) are prepared using the condensation reaction by the Friedel–Crafts procedure. In the produced oligomers, the triphenylamine or N,N′‐dicarbazolyl‐4,4′‐biphenyl core serves as a spacer bearing spiro‐linked fluorene moieties to form a multi‐H shaped structure. This specific structure efficiently retards the crystallization tendency of the pyrene groups, and gives the materials completely amorphous morphological structure and film forming ability. Solution‐processed OLEDs with the structure of ITO/PEDOT:PSS (25 nm)/TPA‐PyF₃ or CBP‐PyF₃ (40 nm)/TPBI (35 nm)/Ca (10 nm)/Ag (100 nm) show low turn‐on voltages of 3.6 V, and the maximum external quantum efficiencies reach 1.78% and 2.07% for TPA‐PyF₃ and CBP‐PyF_3, respectively. Moreover, both devices exhibit stable deep‐blue light emission with Commission International de I'Eclairage (CIE) coordinates of around (0.16, 0.09) at the brightness of 100–1000 cd m^?2. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 795–801     

Efficient blue‐green‐emitting poly[(5‐diphenylamino‐1,3‐phenylenevinylene)‐alt‐(2,5‐dihexyloxy‐1,4‐phenylenevinylene)] derivatives: Synthesis and optical properties

New poly(phenylene vinylene) derivatives with a 5‐diphenylamino‐1,3‐phenylene linkage (including polymers 2 , 3 , and 5 ) have been synthesized to improve the charge‐injection properties. These polymers are highly photoluminescent with fluorescent quantum yields as high as 76% in tetrahydrofuran solutions. With effective π‐conjugation interruption at adjacent m‐phenylene units, chromophores of different conjugation lengths can be incorporated into the polymer chain in a controllable manner. In polymer 2 , the structural regularity leads to an isolated, well‐defined emitting chromophore. Isomeric polymer 3 of a random chain sequence, however, allows the effective emitting chromophores to be joined in sequence by sharing a common m‐phenylene linkage (as shown in a molecular fragment). Double‐layer light‐emitting‐diode devices using 2 , 3 , and 5 as emitting layers have turn‐on voltages of about 3.5 V and produce blue‐green emissions with peaks at 493, 492, and 482 nm and external quantum efficiencies up to 1.42, 0.98, and 1.53%, respectively. In comparison with a light‐emitting diode using 2 , a device using 3 shows improved charge injection and displays increased brightness by a factor of ～3 to 1400 cd/m² at an 8‐V bias. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2307–2315, 2006     

Synthesis of new polyfluorene copolymers with a comonomer containing triphenylamine units and their applications in white‐light‐emitting diodes

Novel conjugated polyfluorene copolymers, poly[9,9‐dihexylfluorene‐2,7‐diyl‐co‐(2,5‐bis(4′‐diphenylaminostyryl)‐phenylene‐1,4‐diyl)]s (PGs), have been synthesized by nickel(0)‐mediated polymerization from 2,7‐dibromo‐9,9‐dihexylfluorene and 1,4′‐dibromo‐2,5‐bis(4‐diphenylaminostyryl)benzene with various molar ratios of the monomers. Because of the incorporation of triphenylamine (TPA) moieties, PGs exhibit much higher HOMO levels than the corresponding polyfluorene homopolymers and are able to facilitate hole injection into the polymer layer from the anode electrode in light‐emitting diodes. Conventional polymeric light‐emitting devices with the configuration ITO/PEDOT:PSS/polymer/Ca/Al have been fabricated. A light‐emitting device produced with one of the PG copolymers (PG10) as the emitting layer exhibited a voltage‐independent and stable bluish‐green emission with color coordinates of (0.22, 0.42) at 5 V. The maximum brightness and current efficiency of the PG10 device were 3370 cd/m² (at 9.6 V) and 0.6 cd/A, respectively. To realize a white polymeric light‐emitting diode, PG10 as the host material was blended with 1.0 wt % of a red‐light‐emitting polymer, poly[9,9‐dioctylfluorene‐2,7‐diyl‐alt‐2,5‐bis(2‐thienyl‐2‐cyanovinyl)‐1‐(2′‐ethylhexyloxy)‐4‐methoxybenzene‐5′,5′‐diyl] (PFR4‐S), and poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV). The device based on PG10:PFR4‐S showed an almost perfect pure white electroluminescence emission, with Commission Internationale de l'Eclairage (CIE) coordinates of (0.33, 0.36) at 8 V; for the PG10:MEH‐PPV device, the CIE coordinates at this voltage were (0.30, 0.40) with a maximum brightness of 1930 cd/m². Moreover, the white‐light emission from the PG10:PFR4‐S device was stable even at different driving voltages and had CIE coordinates of (0.34, 0.36) at 6 V and (0.31, 0.35) at 10 V. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1199–1209, 2007     

Blue‐emitting poly[(m‐phenylene vinylene)‐alt‐(o‐phenylene vinylene)]s: The effect of regioregularity on the optical properties

Poly[(m‐phenylene vinylene)‐alt‐(o‐phenylene vinylene)]s with different contents of cis‐/trans‐CH?CH ( 3 and 6 ) have been synthesized through Wittig condensation. The polymers exhibit good solubility in common organic solvents such as toluene and tetrahydrofuran. A comparison of the optical properties has been made between 3 and its phenyl regioisomers containing either p‐phenylene or m‐phenylene units. The results show that the regiochemistry of the phenyl ring can be a useful tool for tuning the emission color of π‐conjugated polymers because the extension of π conjugation can only partially be achieved through an o‐phenylene bridge. Although both polymers 3 and 6 exhibit comparable low fluorescence quantum efficiencies (≈0.18) in solution, their films are highly luminescent, showing a broad emission band near 456 nm (blue color). Electroluminescence results show that the device of polymer 3 , which has a higher content of trans‐CH?CH linkages, is about 20 times more efficient than that of 6 . © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2650–2658, 2003