Measuring partial fluorescence yield using filtered detectors

Typically, X‐ray absorption near‐edge structure measurements aim to probe the linear attenuation coefficient. These measurements are often carried out using partial fluorescence yield techniques that rely on detectors having photon energy discrimination improving the sensitivity and the signal‐to‐background ratio of the measured spectra. However, measuring the partial fluorescence yield in the soft X‐ray regime with reasonable efficiency requires solid‐state detectors, which have limitations due to the inherent dead‐time while measuring. Alternatively, many of the available detectors that are not energy dispersive do not suffer from photon count rate limitations. A filter placed in front of one of these detectors will make the energy‐dependent efficiency non‐linear, thereby changing the responsivity of the detector. It is shown that using an array of filtered X‐ray detectors is a viable method for measuring soft X‐ray partial fluorescence yield spectra without dead‐time. The feasibility of this technique is further demonstrated using α‐Fe₂O₃ as an example and it is shown that this detector technology could vastly improve the photon collection efficiency at synchrotrons and that these detectors will allow experiments to be completed with a much lower photon flux reducing X‐ray‐induced damage.     

The stopped‐drop method: a novel setup for containment‐free and time‐resolved measurements

A novel setup for containment‐free time‐resolved experiments at a free‐hanging drop is reported. Within a dead‐time of 100 ms a drop of mixed reactant solutions is formed and the time evolution of a reaction can be followed from thereon by various techniques. As an example, a small‐angle X‐ray scattering study on the formation mechanism of EDTA‐stabilized CdS both at a synchrotron and a laboratory X‐ray source is presented here. While the evolution can be followed with one drop only at a synchrotron source, a stroboscopic mode with many drops is preferable for the laboratory source.     

Towards a microchannel‐based X‐ray detector with two‐dimensional spatial and time resolution and high dynamic range

X‐ray detectors that combine two‐dimensional spatial resolution with a high time resolution are needed in numerous applications of synchrotron radiation. Most detectors with this combination of capabilities are based on semiconductor technology and are therefore limited in size. Furthermore, the time resolution is often realised through rapid time‐gating of the acquisition, followed by a slower readout. Here, a detector technology is realised based on relatively inexpensive microchannel plates that uses GHz waveform sampling for a millimeter‐scale spatial resolution and better than 100 ps time resolution. The technology is capable of continuous streaming of time‐ and location‐tagged events at rates greater than 10⁷ events per cm². Time‐gating can be used for improved dynamic range.     

Dead cell and side leakage correction for a lead-scintillating fiber electromagnetic calorimeter

The electromagnetic calorimeter(ECAL) of the Alpha Magnetic Spectrometer(AMS-02) is one of the key detectors for dark matter searches. It measures the energies of electrons, positrons and photons and seperates them from hadrons. Currently, there are 5 dead cells in the ECAL, which affect the reconstructed energy of 4.2%of total events in the ECAL acceptance. When an electromagnetic shower axis is close to the ECAL border, due to the side leakage, the reconstructed energy is affected as well. In this paper, methods for dead cells and side leakage corrections for the ECAL energy reconstruction are presented. For events with the shower axis crossing dead cells,applying dead cell correction improves the difference in the reconstructed energy from 12% to 1%, while for events near the ECAL border, with side leakage correction it is improved from 4% to 1%.     

Energy‐dependent dead‐time correction in digital pulse processors applied to silicon drift detector's X‐ray spectra

Dead‐time effects in X‐ray spectra taken with a digital pulse processor and a silicon drift detector were investigated when the number of events at the low‐energy end of the spectrum was more than half of the total, at counting rates up to 56 kHz. It was found that dead‐time losses in the spectra are energy dependent and an analytical correction for this effect, which takes into account pulse pile‐up, is proposed. This and the usual models have been applied to experimental measurements, evaluating the dead‐time fraction either from the calculations or using the value given by the detector acquisition system. The energy‐dependent dead‐time model proposed fits accurately the experimental energy spectra in the range of counting rates explored in this work. A selection chart of the simplest mathematical model able to correct the pulse‐height distribution according to counting rate and energy spectrum characteristics is included.     

Energy‐dispersive diffraction with synchrotron radiation and a germanium detector

The response of an intrinsic Ge detector in energy‐dispersive diffraction measurements with synchrotron radiation is studied with model calculations and diffraction from perfect Si single‐crystal samples. The high intensity and time‐structure of the synchrotron radiation beam leads to pile‐up of the output pulses, and the energy distribution of the pile‐up pulses is characteristic of the fill pattern of the storage ring. The pile‐up distribution has a single peak and long tail when the interval of the radiation bunches is small, as in the uniform fill pattern, but there are many pile‐up peaks when the bunch distance is a sizable fraction of the length of the shaping amplifier output pulse. A model for the detecting chain response is used to resolve the diffraction spectrum from a perfect Si crystal wafer in the symmetrical Laue case. In the 16‐bunch fill pattern of the ESRF storage ring the spectrum includes a large number of `extra reflections' owing to pile‐up, and the model parameters are refined by a fit to the observed energy spectrum. The model is used to correct for the effects of pile‐up in a measurement with the 1/3 fill pattern of the storage ring. Si reflections (2h,2h,0) are resolved up to h = 7. The pile‐up corrections are very large, but a perfect agreement with the integrated intensities calculated from dynamical diffraction theory is achieved after the corrections. The result also demonstrates the convergence of kinematical and dynamical theories at the limit where the extinction length is much larger than the effective thickness of the perfect crystal. The model is applied to powder diffraction using different fill patterns in simulations of the diffraction pattern, and it is demonstrated that the regularly spaced pile‐up peaks might be misinterpreted to arise from superlattices or phase transitions. The use of energy‐dispersive diffraction in strain mapping in polycrystalline materials is discussed, and it is shown that low count rates but still good statistical accuracy are needed for reliable results.     

High‐performance X‐ray detectors for the new powder diffraction beamline I11 at Diamond

The design and performance characterization of a new light‐weight and compact X‐ray scintillation detector is presented. The detectors are intended for use on the new I11 powder diffraction beamline at the third‐generation Diamond synchrotron facility where X‐ray beams of high photon brightness are generated by insertion devices. The performance characteristics of these detection units were measured first using a radioactive source (efficiency of detection and background count rate) and then synchrotron X‐rays (peak stability, light yield linearity and response consistency). Here, the results obtained from these tests are reported, and the suitability of the design for the Diamond powder beamline is demonstrated by presenting diffraction data obtained from a silicon powder standard using a prototype multicrystal analyser stage.     

Computer‐assisted area detector masking

Area detectors have become the predominant type of detector for the rapid acquisition of X‐ray diffraction, small‐angle scattering and total scattering. These detectors record the scattering for a large area, giving each shot good statistical significance to the resulting scattered intensity I(Q) pattern. However, many of these detectors have pixel level defects, which cause error in the resulting one‐dimensional patterns. In this work, new software to automatically find and mask these dead pixels and other defects is presented. This algorithm is benchmarked with both ideal simulated and experimental datasets.     

In-line X-ray lensless imaging with lithium fluoride film detectors

In this work, we present preliminary in-line X-ray lensless projection imaging results at a synchrotron facility by using novel solid-state detectors based on non-destructive readout of photoluminescent colour centres in lithium fluoride thin films. The peculiarities of LiF radiation detectors are high spatial resolution on a large field of view, wide dynamic range, versatility and simplicity of use. These properties offered the opportunity to test a broadband X-ray synchrotron source for lensless projection imaging experiments at the TopoTomo beamline of the ANKA synchrotron facility by using a white beam spectrum (3–40 keV). Edge-enhancement effects were observed for the first time on a test object; they are discussed and compared with simulations, on the basis of the colour centre photoluminescence linear response found in the investigated irradiation conditions.     

Counting‐loss correction for X‐ray spectroscopy using unit impulse pulse shaping

High‐precision measurement of X‐ray spectra is affected by the statistical fluctuation of the X‐ray beam under low‐counting‐rate conditions. It is also limited by counting loss resulting from the dead‐time of the system and pile‐up pulse effects, especially in a high‐counting‐rate environment. In this paper a detection system based on a FAST‐SDD detector and a new kind of unit impulse pulse‐shaping method is presented, for counting‐loss correction in X‐ray spectroscopy. The unit impulse pulse‐shaping method is evolved by inverse deviation of the pulse from a reset‐type preamplifier and a C‐R shaper. It is applied to obtain the true incoming rate of the system based on a general fast–slow channel processing model. The pulses in the fast channel are shaped to unit impulse pulse shape which possesses small width and no undershoot. The counting rate in the fast channel is corrected by evaluating the dead‐time of the fast channel before it is used to correct the counting loss in the slow channel.     

Quantitative performance measurements of bent crystal Laue analyzers for X‐ray fluorescence spectroscopy

Third‐generation synchrotron radiation sources pose difficult challenges for energy‐dispersive detectors for XAFS because of their count rate limitations. One solution to this problem is the bent crystal Laue analyzer (BCLA), which removes most of the undesired scatter and fluorescence before it reaches the detector, effectively eliminating detector saturation due to background. In this paper experimental measurements of BCLA performance in conjunction with a 13‐element germanium detector, and a quantitative analysis of the signal‐to‐noise improvement of BCLAs are presented. The performance of BCLAs are compared with filters and slits.     

A 3 × 6 arrayed CCD X‐ray detector for continuous rotation method in macromolecular crystallography

A 3 × 6 arrayed charge‐coupled device (CCD) X‐ray detector has been developed for the continuous‐rotation method in macromolecular crystallography at the Photon Factory. The detector has an area of 235.9 mm × 235.9 mm and a readout time of 1.9 s. The detector is made of a 3 × 6 array of identical modules, each module consisting of a fiber‐optic taper (FOT), a CCD sensor and a readout circuit. The outputs from 18 CCDs are read out in parallel and are then digitized by 16‐bit analog‐to‐digital converters. The advantage of this detector over conventional FOT‐coupled CCD detectors is the unique CCD readout scheme (frame transfer) which enables successive X‐ray exposures to be recorded without interruption of the sample crystal rotation. A full data set of a lysozyme crystal was continuously collected within 360 s (180° rotation, 3 s/1.5° frame). The duty‐cycle ratio of the X‐ray exposure to the data collection time was almost 100%. The combination of this detector and synchrotron radiation is well suited to rapid and continuous data collection in macromolecular crystallography.     

The first microbeam synchrotron X‐ray fluorescence beamline at the Siam Photon Laboratory

The first microbeam synchrotron X‐ray fluorescence (µ‐SXRF) beamline using continuous synchrotron radiation from Siam Photon Source has been constructed and commissioned as of August 2011. Utilizing an X‐ray capillary half‐lens allows synchrotron radiation from a 1.4 T bending magnet of the 1.2 GeV electron storage ring to be focused from a few millimeters‐sized beam to a micrometer‐sized beam. This beamline was originally designed for deep X‐ray lithography (DXL) and was one of the first two operational beamlines at this facility. A modification has been carried out to the beamline in order to additionally enable µ‐SXRF and synchrotron X‐ray powder diffraction (SXPD). Modifications included the installation of a new chamber housing a Si(111) crystal to extract 8 keV synchrotron radiation from the white X‐ray beam (for SXPD), a fixed aperture and three gate valves. Two end‐stations incorporating optics and detectors for µ‐SXRF and SXPD have then been installed immediately upstream of the DXL station, with the three techniques sharing available beam time. The µ‐SXRF station utilizes a polycapillary half‐lens for X‐ray focusing. This optic focuses X‐ray white beam from 5 mm × 2 mm (H × V) at the entrance of the lens down to a diameter of 100 µm FWHM measured at a sample position 22 mm (lens focal point) downstream of the lens exit. The end‐station also incorporates an XYZ motorized sample holder with 25 mm travel per axis, a 5× ZEISS microscope objective with 5 mm × 5 mm field of view coupled to a CCD camera looking to the sample, and an AMPTEK single‐element Si (PIN) solid‐state detector for fluorescence detection. A graphic user interface data acquisition program using the LabVIEW platform has also been developed in‐house to generate a series of single‐column data which are compatible with available XRF data‐processing software. Finally, to test the performance of the µ‐SXRF beamline, an elemental surface profile has been obtained for a piece of ancient pottery from the Ban Chiang archaeological site, a UNESCO heritage site. It was found that the newly constructed µ‐SXRF technique was able to clearly distinguish the distribution of different elements on the specimen.     

Design and construction of multicrystal analyser detectors using Rowland circles: application to MAD26 at ALBA

A concept is given for describing multicrystal analyser detectors (MADs), as they are in use for synchrotron powder diffraction, on the basis of the Rowland circle construction. The Rowland circle is typically used to describe focusing geometries and can be adapted for the case of MADs working at a single energy as well as in a limited energy range. With this construction it is also possible to quantify and optimize the walk of the beam along non‐central crystals which is inevitable in certain detector designs. The results of this geometrical inspection are correlated with a real detector design that is implemented at the ALBA synchrotron facility in Spain. An error budget is given to estimate the influence and amount of tolerance of the manufacturing process.     

Calibration of a compact XUV soft X‐ray monochromator with a digital autocollimator in situ

A digital autocollimator of resolution 0.1 µrad (0.02 arcsec) serves as a handy correction tool for calibrating the angular uncertainty during angular and lateral movements of gratings inside a monochromator chamber under ultra‐high vacuum. The photon energy dispersed from the extreme ultraviolet (XUV) to the soft X‐ray region of the synchrotron beamline at the Taiwan Light Source was monitored using molecular ionization spectra at high resolution as energy references that correlate with the fine angular steps during grating rotation. The angular resolution of the scanning mechanism was <0.3 µrad, which results in an energy shift of 80 meV at 867 eV. The angular uncertainties caused by the lateral movement during a grating exchange were decreased from 2.2 µrad to 0.1 µrad after correction. The proposed method provides a simple solution for on‐site beamline diagnostics of highly precise multi‐axis optical manipulating instruments at synchrotron facilities and in‐house laboratories.     

Decaying source model: Alternative approach to determination of true counting rates at X and gamma ray counting systems

The counting systems consisting of electronic devices are used for detection of radiation due to X or gamma rays. The dead time of the counting system is based on time limitations of these electronic devices. The dead time causes counting losses. Determination of counting rate losses in quantitative and qualitative analysis become a vital step for correction of analysis. Therefore, compensating for counting rate losses is of great importance. These counting rate losses are due to piled up reject time, paralyzable or non-paralyzable system dead time or a combination of these mechanisms. Paralyzable and non-paralyzable models are well-known and frequently used for correction of counting rate losses dependent on the system dead time. However, these two models do not provide enough correction at medium and high counting rates. Therefore, the new models for corrections of counting rate losses are needed. For this reason, both an alternative approach is proposed and a simulation program is coded for counting rate losses in this study. A good agreement is obtained between theoretical model and simulation program.     

Single-cell analysis using Fourier transform infrared microspectroscopy

Fourier transform infrared spectroscopy (FTIR) is a well-established, non-destructive method of obtaining chemical information from biological samples such as tissues and cells. This review focuses specifically on the development of infrared spectroscopic microanalysis at the single-cell level. Technological developments, including that of the infrared microscope, synchrotron radiation FTIR, and focal plane array detectors, and their impact on the field are discussed along with the various data processing procedures that are currently used to extract meaningful information. There is then an emphasis on live cell infrared (IR) imaging, including developments in water correction and microfluidic device design. The review concludes with look to future directions, highlighting the potential impact of quantum cascade lasers.     

同步辐射探测器的应用与发展

探测器是同步辐射实验的重要环节。探测器水平必须不断提高才能适应同步辐射发展的需求，最大限度地发挥先进光源为人类研究提供的强大支持作用。文章介绍了当前同步辐射实验中普遍使用的各种探测器的原理和特点，并就一些新型探测器的发展情况进行了阐述。     

A method to determine the absolute harmonic content of an X‐ray beam using attenuation measurements

We present a new method for determining the absolute harmonic content of an X‐ray beam. The technique is applied to determine the harmonic content of a synchrotron beam to high‐accuracy by measuring the X‐ray attenuation of a large number of aluminium foils with thicknesses varying over several orders of magnitude. Earlier methods always determined relative quantities such as the effective harmonic content, which are dependant on experimental geometry and not transferable between detectors. We use a more fundamental and useful parameter: the harmonic‐photon percentage. Copyright © 2009 John Wiley & Sons, Ltd.     

Pump−probe experiments at the TEMPO beamline using the low‐α operation mode of Synchrotron SOLEIL

The SOLEIL synchrotron radiation source is regularly operated in special filling modes dedicated to pump–probe experiments. Among others, the low‐α mode operation is characterized by shorter pulse duration and represents the natural bridge between 50 ps synchrotron pulses and femtosecond experiments. Here, the capabilities in low‐α mode of the experimental set‐ups developed at the TEMPO beamline to perform pump–probe experiments with soft X‐rays based on photoelectron or photon detection are presented. A 282 kHz repetition‐rate femtosecond laser is synchronized with the synchrotron radiation time structure to induce fast electronic and/or magnetic excitations. Detection is performed using a two‐dimensional space resolution plus time resolution detector based on microchannel plates equipped with a delay line. Results of time‐resolved photoelectron spectroscopy, circular dichroism and magnetic scattering experiments are reported, and their respective advantages and limitations in the framework of high‐time‐resolution pump–probe experiments compared and discussed.