Supercapacitive properties of electrodeposited RuO2 electrode in acrylic gel polymer electrolytes

Hydrous ruthenium oxide (RuO₂) is prepared by electrodeposition on a platinum substrate and its supercapacitive properties are characterized adopting acrylic gel polymer electrolytes, such as poly(acrylic acid) (PAA), potassium polyacrylate (PAAK), and poly(2-acrylamido-2-methyl-1-propanesulfonic acid) (PAMPS). The electrodeposited hydrous RuO₂ exhibits an amorphous compact stratified morphology with a higher loading (0.15 mg cm^?2) than that of a previous report, and shows broad redox peaks on both cathodic and anodic scans in the cyclic voltammetry. In particular, the RuO₂ electrode for supercapacitor adopting the PAMPS electrolyte shows the highest specific capacitance of 642 F g^?1 at 20 mV s^?1. This is due to the efficient utilization of active RuO₂ species and greater proton accommodation toward the negative oxygen sites of PAMPS's side chain. In addition, it is possible to improve sustainability against high-rate current with the RuO₂ electrode with the PAMPS electrolyte, due to the crosslinks of the gel electrolyte, which support the mechanical strength.     

One-dimensional confinement in heterogeneous catalysis: Trapped oxygen on RuO2(110) model catalysts

With temperature programmed reaction (TPR) experiments and kinetic Monte Carlo (kMC) simulations of coadsorbed oxygen and HCl on the RuO₂(110) surface we studied the thermal stabilization of dissociatively adsorbed oxygen. Due to one-dimensional confinement single surface O atoms can be trapped by surface chlorine atoms so that surface oxygen is not able to desorb from the RuO₂(110) surface at the expected temperature of 420 K. Trapped oxygen needs desorption temperatures as high as 700 K where it recombines with bridging O from RuO₂(110) to form O₂. Kinetic modeling of catalytic reactions with dimensional confinement of their reaction intermediates on the catalyst's surface requires the application of kinetic Monte Carlo simulations which are beyond the mean field approach.     

Electrode reaction at platinum / ceria surface modified YSZ interface

The electrode reaction was examined on ceria coated YSZ by a platinum point electrode in H₂-H₂O atmosphere at 973 K- 1173 K. The thickness of the ceria coating layer was altered from 0 to 2.5 μm, fabricated by a laser ablation and by a vacuum vapor deposition method on YSZ single crystals. The electrode / electrolyte interface conductivity increased with 1/4 powers ofp(H₂) andp(H₂O) on both ceria coated and non-coated YSZ. The interface conductivity was significantly improved on a thicker ceria coating surface than 1 μm. The effective electrode reaction radius also increased in a thick ceria coating. The¹⁸O/¹⁶O exchange experiment at low oxygen partial pressure revealed that the oxygen surface exchange rate of ceria is not high compared with that of YSZ. It can be concluded that the bulk ionic conduction of ceria makes a more effective contribution to the electrode reaction than the surface catalytic activity in H₂-H₂O atmosphere. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

CO oxidation over Ru(0 0 0 1) at near-atmospheric pressures: From chemisorbed oxygen to RuO2

RuO₂(1 1 0) was formed on Ru(0 0 0 1) under oxygen-rich reaction conditions at 550 K and high pressures. This phase was also synthesized using pure O₂ and high reaction temperatures. Subsequently the RuO₂ was subjected to CO oxidation reaction at stoichiometric and net reducing conditions at near-atmospheric pressures. Both in situ polarization modulation infrared reflection absorption spectroscopy (PM-IRAS) and post-reaction Auger electron spectroscopy (AES) measurements indicate that RuO₂ gradually converts to a surface oxide and then to a chemisorbed oxygen phase. Reaction kinetics shows that the chemisorbed oxygen phase has the highest reactivity due to a smaller CO binding energy to this surface. These results also show that a chemisorbed oxygen phase is the thermodynamically stable phase under stoichiometric and reducing reaction conditions. Under net oxidizing conditions, RuO₂ displays high reactivity at relatively low temperatures (?450 K). We propose that this high reactivity involves a very reactive surface oxygen species, possibly a weakly bound, atomic oxygen or an active molecular O₂ species. RuO₂ deactivates gradually under oxidizing reaction conditions. Post-reaction AES measurements reveal that this deactivation is caused by a surface carbonaceous species, most likely carbonate, that dissociates above 500 K.     

Behaviour of a dense In2O3/ YSZ electrode in oxygen containing atmospheres

A study of electrical and electrochemical properties of a dense In₂O₃ electrode in contact with a single crystal YSZ electrolyte was carried out by d.c. and a.c. methods. As a result, it was found that dense In₂O₃ electrodes have high electrical conductivity but very low electrochemical activity. In a vicinity of the equilibrium potential and under the anodic polarisation, the rate of Faraday reaction at the In₂O₃ electrodes was as low as to consider the electrode a blocking one. The blocking properties of the In₂O₃ electrodes were used to measure the hole conductivity of the YSZ electrolyte in the temperature range between 795 to 1163 K and oxygen partial pressure from 1 to 10⁵ Pa. A comparison with the literature data confirmed that the dense In₂O₃ electrode blockes the ionic transfer through the YSZ. A set of experiments indicated that the oxygen exchange between the indium oxide surface presented to the oxygen containing gaseous phase and this phase is very poor. A route of the electrode process at O₂, In₂O₃ / YSZ electrode was proposed a limiting stage of which is the discharge of the oxygen ions to the atomic oxygen adsorbed on the electrode surface: $$O_0 ^x \left( {In_2 O_3 } \right)_s = V_0 ^{ \bullet \bullet } \left( {In_2 O_3 } \right)_s + O_{ad} \left( {In_2 O_3 } \right)_s + 2e'\left( {In_2 O_3 } \right).$$ The polarisation resistance decreases when platinum or the praseodymium oxide is deposited on the surface of the In₂O₃ electrodes. The cathodic polarisation also increases the electrochemical activity of the electrodes. Both the establishment of the steady state of the electrode under polarisation and the recovery of the equilibrium state by the electrode are very long processes, which are probably related to the diffusion mechanism by which the stoichiometry of the indium oxide is changed.     

Superior capacitive characteristics of RuO2 nanorods grown on carbon nanotubes

Carbon nanotubes (CNTs) were used as the electric double layer capacitor (EDLC) material and were synthesized by using thermal chemical vapor deposition (TCVD). To enhance the EDLC capacity, the ruthenium dioxide (RuO₂) nanorods were grown on CNTs by using metal organic chemical vapor deposition (MOCVD). The synthesized CNTs were the principal part and template, and the RuO₂ nanorods were grown outwardly from CNTs. The increase of effective specific area between electrode and electrolyte played an important role in enhancing the capacitance. Different concentrations of KOH were used as electrolyte to measure the capacitance to find the variation of capacitance. Moreover, the RuO₂/CNT composites demonstrated a stable cycle life. The results showed that the RuO₂/CNT composites were a promising supercapacitor device material.     

Effects of annealing holding time on capacitance performance of RuO2–IrO2–graphene/Ti electrodes

The thermal decomposition method was used to prepare composite electrodes of the Ruthenium oxide–Iridium oxide–Graphene (RuO₂–IrO₂–G). Scanning Electron Microscopy (SEM), X–ray diffraction analysis (XRD), and electrochemical tests were used to study the influence of different annealing holding time on the surface morphology, phase composition, and capacitive performance of the coatings. The results showed that more and more RuO₂, IrO₂ nanoparticles were observed on the surface and cracks of the coating as the annealing holding time increasing. The RuO₂–IrO₂–G/Ti electrode was obtained by annealing for 5 h. The coating of the electrode consists of a certain amount of amorphous phase and nano–crystalline phase, and it had good electronic conductivity and ionic conductivity. At the same time, the electrode was prepared at 5 h had the largest specific capacitance of 778.46 F/g, which increased by 430.89 F/g than the electrode was prepared at 1 h. In addition, the electrode also had superior capacitance performance, capacitance retention and power characteristics.     

In situ FTIR study of oxygen adsorption on nanostructured RuO2 thin-film electrode

In situ Fourier transform spectroscopy (FTIR) was used to study interactions of nanostructured ruthenium oxide (RuO₂) thin-film sensing electrode with O₂ at room temperature. RuO₂ nanostructures were pretreated at 1,000 °C for 1 h in order to obtain good crystallinity of amorphous RuO₂ nanoparticles. Morphology and properties of nanostructured RuO₂ were characterized by X-ray diffraction, thermo-gravimetric/differential thermal analysis, scanning electron microscopy, and FTIR. It was shown that pretreated RuO₂ is quite active for O₂ ⁻, O₂ ²⁻, and O²⁻ adsorption with clear 722 cm⁻¹ band for superoxide ions (O₂ ⁻) adsorption for the different oxygen concentrations. The results of in situ FTIR measurements revealed that the active sites for oxygen adsorption are not limited to the triple boundaries, but extended to surfaces of RuO₂ electrodes. Fundamental vibration frequencies of ruthenium–oxygen bond at a temperature of 23 °C as well as region above fundamental frequencies for the nanostructured RuO₂ were identified.     

Performance of palladium electrode for electrochemical hydrogen pump using strontium-zirconate-based proton conductors

An electrode design with no use of three-phase boundary was investigated using palladium electrode. The hydrogen evolution rate of the palladium electrode cell using SrZr_0.9Y_0.1O_3 − α electrolyte followed Faraday’s law up to 180 mA cm⁻², and the anode and cathode overpotentials were significantly lower than those of a platinum electrode cell, suggesting that the palladium electrode is effective to improve the performance of the hydrogen-pumping cell using SrZrO₃-based electrolyte. The rate-determining step (RDS) for electrode reaction was also investigated by changing the electrode morphology and hydrogen partial pressure, and it was suggested that the RDS of the anode is a reaction at electrode/electrolyte interface.     

Antioxidant behaviour of 2′‐hydroxy‐chalcones: a study of their electrochemical properties

The electrochemical behaviour of 13 chalcone analogues was systematically studied by means of cyclic voltammetry and chronoamperometry at a glassy carbon (GC), gold and platinum working electrodes using two different supporting electrolyte/solvent combinations. It was found that chalcone analogues can be easily oxidized at both GC and gold working electrodes, but not at a platinum electrode. Principal component analysis was further employed to reveal similarities/dissimilarities between oxidation potentials, chronoamperometric signals and ability of the compounds to scavenge the reactive oxygen species H₂O₂. The study reveals the inverse proportional relationship between the scavenging ability of H₂O₂, expressed as IC₅₀, and chronoamperometric signal at 800 mV using gold as working electrode. Copyright © 2012 John Wiley & Sons, Ltd.     

Three-electrode solid-state fuel cell for evaluating working electrodes

Development of a commercial solid-state fuel cell depends on identification of suitable catalytic electrodes to replace platinum. A three-electrode test cell for electrode evaluation is reported. The solid protonic electrolyte used was dodecamolybdophosphoric acid, H₃Mo₁₂PO₄₀·29H₂O, and a thin platinum wire inserted into the electrolyte served as the third electrode. Reproducibility and insensitivity to third-electrode position were demonstrated. The third electrode measures separately the anode and cathode interfacial resistances, thus providing a direct measure of the relative catalytic activity of a given test electrode. Application of the technique is illustrated.     

Switching effect at a platinum electrode on stabilized zirconia during oxygen reduction in the presence of NO

A galvanic cell based upon the use of stabilized zirconia as solid oxygen ion conductor has been used to measure cathodic reduction currents at a porous platinum electrode in both nitrogen-oxygen gas mixtures with and without small amounts of NO (up to 5450 ppm). Adding small amounts of NO to the N₂/O₂ mixture induced a considerable cathodic current peak at the working electrode in the first moment after addition. After interruption of the NO exposure, the opposite effect, a high current pulse in anodic direction, was observed. The switching effect is reproducible and its magnitude depends on the concentrations of oxygen and nitrogen monoxide in the gas. As the main contribution to the current results from the reduction of the excess oxygen in the gas, it must be concluded that the presence of NO strongly affects the steady state, in particular the adsorbed oxygen at the electrode/electrolyte interface. These experimental results are interpreted in terms of a reversible change of the interface which may be due to a reconstruction of the platinum surface in the presence of NO and corresponding drastic change in the amount of adsorbed oxygen at the platinum surface. Paper presented at the 1st Euroconference on Solid State Ionics, Zakynthos, Greece, 11 – 18 Sept. 1994     

Hydroxyl ion conduction in ytterbium-doped strontium cerate at T<580 K in H2O/air atmosphere

Open circuit voltage (OCV) measurements in H₂O/air concentration cells at T<580 K using Yb-doped SrCeO₃ electrolyte indicate that under these conditions, protons are transported through the electrolyte as -ve ions, possibly as hydroxyl (OH⁻) ions. The H⁺ ionic transport, which is generally reported, becomes the dominant mode for H₂O/air concentration cells at temperatures greater than 750 K or when H₂O/air electrodes are replaced by H₂/Ar, and the anomalous OCV sign disappears. The combination of low temperature and the presence of hydrogen and oxygen as provided by the H₂O/air system appears to be necessary for the postulated hydroxyl ion electrode reactions to take place. In addition to OCV measurements, results from impedance spectroscopy are used to provide evidence in support of the suggested hydroxyl ion mode of protonic transport under the specified conditions. These findings are directly relevant in the development of novel humidity sensors in the temperature range 450–580K and is reported in a separate paper in this conference. Paper presented at the 3rd Euroconference on Solid State Ionics, Teulada, Sardinia, Italy, Sept. 15–22, 1996     

Electrochemical characterization on layered lithium ruthenate for electrochemical supercapacitors

Electrochemical characteristics of lithium ruthenate (Li_xRuO_2+0.5x·nH₂O) for electrochemical capacitors' electrode material were first examined in this paper by cyclic voltammetry, electrochemical impedance spectroscopy and galvanostatic charge–discharge tests. Results show that Li_xRuO_2+0.5x·nH₂O has electrochemical capacitive characteristic within the potential range of − 0.2–0.9 V (vs. SCE) in 1 M Li₂SO₄ solution. The capacitance mainly arises from pseudo-capacitance caused by lithium ions' insertion/extraction into/out of the Li_xRuO_2+0.5x·nH₂O electrode. The specific capacitance of 391 F g^− 1 can be delivered at 1 mA charge–discharge current for Li_xRuO_2+0.5x·nH₂O electrode with an energy density of 65.7 W h kg^− 1. This material also exhibits an excellent cycling performance and there is no attenuation of capacitance over 600 cycles.     

Utilization of a dilute solid electrolyte in an oxygen gauge

An electrochemical cell involving a SrCl₂-based solid electrolyte either doped or undoped with SrO was investigated. The measuring electrode was of graphite or vitreous carbon and the reference electrode was formed by dissolving Ag⁺ ions and embedding a silver wire. A simple fabrication technique is described. The reported results indicate that an electrode reaction involving dissolved oxide ions: O₂(gas)+4e⁻=2O²⁻ (SrCl₂) can take place and be utilized in an oxygen gauge down to 200°C. The same cell also functions as a chlorinesensor. At least down to 10⁻³ atm, interference with oxygen is negligible.     

Gold-composite electrodes for hydrocarbon sensors based on YSZ solid electrolyte

In potentiometric zirconia based sensors gold electrodes show a high sensitivity for hydrocarbons (HC's) when the measurements are carried out in non equilibrated oxygen containing gas mixtures at temperatures <700 °C. This behaviour explained by mixed potential theory is not stable and depends strongly on preparation and particularly on measuring conditions. To modify the electrode behaviour composites consisting of gold and gallium oxide were investigated. Gold pastes with different amount of Ga₂O₃ were prepared and screen printed on YSZ pellets. After sintering at defined temperatures between 900 and 950 °C the cells were tested regarding the electrode behaviour in a C₃H₆, O₂ gas mixture using a platinum air reference electrode. These composite electrodes show as compared with pure gold an enhanced sensitivity at low propylene concentrations and a time-independent characteristic at high concentrations of C₃H₆. The optimal composition is found to be at 20 mass-% Ga₂O₃. This electrode can be treated in reducing gases at temperatures 850 °C without changing its characteristics. Paper presented at the 7th Euroconference on Ionics, Calcatoggio, Corsica, France, Oct. 1–7, 2000.     

Electrode materials, interface processes and transport properties of yttria-doped zirconia

The kinetics of the oxygen exchange reactions at the electrodes of a galvanic cell using yttria-doped zirconia single crystals (9.5 mole-% Y₂O₃) as solid electrolyte and Pt or Ag as electrode materials was studied by complex impedance spectroscopy. The electrode resistance when using silver was found to have negligible values over the temperature range 180 – 900 °C. In agreement with these results, oxygen sensors were tested successfully at temperatures as low as 200 °C. According to the performance of silver as electrode material, an electrochemical method was developed to determine the oxygen diffusion coefficient in doped zirconia. The results obtained, compared to those of conductivity and oxygen tracer diffusion measurements, have allowed us to obtain information both on the structure of the defects in yttria-doped zirconia and on the correlation factor. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

High temperature magnetic ordering in La2RuO5

Magnetic susceptibility, heat capacity and electrical resistivity measurements have been carried out on a new ruthenate, La₂RuO₅ (monoclinic, space group P2₁/c) which reveal that this compound is a magnetic semiconductor with a high magnetic ordering temperature of 170 K. The entropy associated with the magnetic transition is 8.3 J/mol K close to that expected for the low spin (S=1) state of Ru⁴⁺ ions. The low temperatures specific heat coefficient γ is found to be nearly zero consistent with the semiconducting nature of the compound. The magnetic ordering temperature of La₂RuO₅ is comparable to the highest known Curie temperature of another ruthenate, namely, metallic SrRuO₃, and in both these compounds the nominal charge state of Ru is 4+.     

Electrode reactions at oxygen,noble metal / stabilized zirconia interfaces

The polarization behaviour of electrodes of the type “oxygen, noble metal / stabilized zirconia”, comprising different zirconia-based materials as electrolyte, platinum or gold as metal component and an oxygen containing gas atmosphere, was investigated at elevated temperatures under equilibrium and non-equilibrium conditions by means of impedance spectroscopy. Massive metal contacts were used as part of the working electrodes. Under non-polarized conditions, the experimental results for platinum indicate a basically uniform reaction mechanism in a vast range of temperature and oxygen partial pressure, involving the surface diffusion of dissociatively adsorbed oxygen on platinum towards the electrochemical reaction sites on the electrolyte surface as rate-determining step. The experimental findings for gold are consistent with the occurrence of two competing reaction mechanisms, namely a charge transfer controlled process and a surface diffusion controlled process, each of them prevailing in different regimes of temperature and oxygen partial pressure. Under polarized conditions, a significant decrease of the polarization resistance takes place, followed by the onset of low frequency loops in the impedance spectra. In the case of cathodic polarization, the onset voltage can be correlated with the partial electron conductivity of the electrolyte, thus confirming the hypothesis of direct participation of electronic species of the electrolyte in the electrode reaction under biased conditions. At moderate temperatures, the polarization induced changes in the electrode properties exhibit a slow relaxation behaviour. This can be attributed to the successive annihilation of additional metastable electrochemical reaction sites having been created during the preceding polarization treatment. Paper presented at the 3rd Euroconference on Solid State Ionics, Teulada, Sardinia, Italy     

Temperature dependence of NO2 sensitivity of YSZ-based mixed potential type sensor attached with NiO sensing electrode

A mixed potential type yttria-stabilized zirconia-based sensor using NiO sensing electrode and Pt reference electrode was fabricated, and its NO₂ sensing characteristics were examined at various operating temperatures in the range of 700–950 °C. It was observed that the sensitivity to NO₂ strongly depends on the operating temperature of the sensor; the sensitivity decreases with increasing operating temperature, while the response/recovery rates increase. To rationalize this temperature dependence of NO₂ response, polarization curves and complex impedances of the sensor were measured in the base gas and in the sample gas (400 ppm NO₂?+?base gas) at various operating temperatures. It turned out that the operating temperature had a strong influence on the rate of anodic reaction of oxygen; the increased rate of anodic reaction leads to lower NO₂ sensitivity and quicker response/recovery at higher operating temperature.