石墨烯修饰玻碳电极在对苯二酚存在下选择性测定米吐尔

制备了石墨烯修饰玻碳电极(GN/GCE)。 在0.5 mol/L HAc-NaAc(pH=4.8)缓冲溶液中,用循环伏安法(CV)和方波伏安法(SWV)研究了米吐尔在修饰电极上的电化学行为,建立了测定米吐尔的新方法。 研究表明,米吐尔在GN/GCE上的氧化、还原峰电势差比其在裸玻碳电极(GCE)上的小,峰电流显著增加,说明GN/GCE对米吐尔有电催化作用;共存物对苯二酚干扰米吐尔的测定,通过方波伏安法可以消除其干扰。 在方波伏安曲线上,米吐尔的还原峰电流与其浓度在8.0×10^-8~5.0×10^-5 mol/L范围内呈线性关系,检出限为2.0×10^-8 mol/L。 该法可用于照相显影废液中米吐尔的测定。     

米吐尔在离子液体修饰碳糊电极上的电化学行为及其测定

用离子液体1-庚基-3-甲基咪唑六氟磷酸([HMIM][PF6])作修饰剂制备了离子液体修饰碳糊电极(IL/CPE).在0.5 mol/L HAc-NaAc(pH=4.8)缓冲溶液中,采用循环伏安法(CV)和方波伏安法(SWV)研究了米吐尔在该修饰电极上的电化学行为,建立了测定米吐尔的新方法.研究表明,米吐尔在IL/CPE上的氧化、还原峰电位差比其在裸碳糊电极(CPE)上的小,而峰电流却显著增加,说明IL/CPE对米吐尔有电催化作用;共存物对苯二酚干扰米吐尔的测定,通过方波伏安法可以消除其干扰.在方波伏安曲线上,米吐尔的还原峰电流与其浓度在1.0×10-7 ～2.0×10-5 mol/L范围内呈线性关系,检出限为3.0×10-8 mol/L.该法可用于照相废液中米吐尔的测定.     

示波极谱滴定法测定显影液中米吐尔和对苯二酚含量

用１．５ｍｏｌ／Ｌ乙酸铵－氨（ｐＨ８．２）－无水乙醇（２：１，Ｖ／Ｖ）混合溶液为极谱底液，以Ｋ２ＣｒＯ４与米吐尔和对苯二酚的氧化还原反应为基础，用Ｋ２ＣｒＯ４作为滴定剂，以示波极谱图上ＣｒＯ４＾２－切口出现指示终点，测定显影液中米吐尔和对苯二酚的含量。本法简便易行，灵敏准确，终点直观，应用于Ｄ－７２和Ｄ－７６显影液中米吐尔和对苯二酚的测定，获得满意结果。     

米吐尔在多壁碳纳米管修饰电极上的电化学行为及其应用

制备了多壁碳纳米管修饰玻碳电极(MWCNT/GCE),研究了该电极对米吐尔的电催化作用及测定溶液中米吐尔的分析条件。实验表明:在常见的支持电解质中,米吐尔在MWCNT/GCE上比裸玻碳电极(GCE)上氧化还原峰电位差要小,而峰电流显著增加,因此该电极对米吐尔有电催化作用;在pH=1.0的HCl-KCl支持电解质中,米吐尔的电流响应最佳;扫速增加,峰电流增加,但峰电位受溶液电阻的影响而发生位移,峰形变差,最佳扫描速度为0.12V/s;一些常见物质对测定无干扰,米吐尔浓度与峰电流的关系为:Ipc=0.1126C 1.393×10-4(r=0.9982);共存的对苯二酚(HQ)干扰测定,但可通过二次微分CV曲线方法消除干扰,在8.0×10-2~1.0×10-5mol/L范围内,其浓度与二次微分还原峰面积线性关系为:Apc=8.562×10-4C 1.801×10-6(r=0.9986);检出限达5.0×10-6mol/L。     

碳糊电极阳极溶出伏安法同时测定显影废水中的微量米吐尔和对苯二酚

1978年Smith介绍了美国对制片废水的控制及其中某些有害成份加对苯二酚等的测定方法,但未谈及米吐尔的测定,官宜文等曾利用萃取-紫外光度法同时测定了显影废水中的米吐尔和对苯二酚。但是,本法尚未见报道。 1 仪器与试剂 75—4B型快速极谱仪(厦门二分厂),79—1型伏安分析仪(济南无线电四厂),甘汞电极为参比电极,     

2-疏基乙醇自组装膜电极的制备及其电化学性质

示差脉冲伏安法;2-疏基乙醇自组装膜电极的制备及其电化学性质;米吐尔;对苯二酚     

L-半胱氨酸自组装膜电极对米吐尔的电催化及其分析应用

研究了米吐尔在L 半胱氨酸自组装膜修饰金电极上的电化学行为。米吐尔在该修饰电极上的CV曲线仅出现一对峰 ,其峰形对称 ,ΔEp =42mV ,氧化还原峰电流之比约等于 1,为可逆反应 ;扩散系数D =2 .2 4× 10 - 6 cm2 ·s- 1 。初步探讨了电催化机理。差分脉冲伏安法测定其氧化峰电流与米吐尔浓度在 5 .0× 10 - 7～ 2 .0× 10 - 5mol/L和 5 .0× 10 - 5～ 1.0× 10 - 3 mol/L范围内分段呈线性关系 ;相关系数分别为 0 .9987和 0 .9972 ;检测限 1.0× 10 - 8mol/L     

基于碳纳米管-石墨烯纳米片复合膜修饰金电极同时测定邻苯二酚和对苯二酚

制备了一种碳纳米管-石墨烯纳米片复合膜修饰金电极的用于同时测定邻苯二酚和对苯二酚电化学传感器。 并应用循环伏安法研究了邻苯二酚和对苯二酚在该电极上的电化学行为,邻苯二酚和对苯二酚的浓度检测采用差分脉冲伏安法,结果表明,碳纳米管-石墨烯纳米片复合膜极大的增强了邻苯二酚和对苯二酚的电催化活性。 并在0.5~6.0×10-4 mol/L浓度范围内与响应电流有良好的线性关系。邻苯二酚和对苯二酚的最低检测限分别是5.0×10-9和4.8×10-9 mol/L。 该电化学传感器能用于实际样品中的酚类化合物的检测。     

示波极谱滴定法测定显影液中米吐尔含量

1引言米吐尔为对一甲氨基苯酚硫酸盐,它是黑白显影液中的主显影剂。显影液中米吐尔的测定通常采用分光光度法和林量法,电分析方法目前尚未见报道。光度法需要绘制曲线,较为费时;林量法则由于苹取分离样品时,乙酸乙酯和水相存在微量互溶,以及分层略有混溶,米吐尔的分析结果容易偏高,而形成系统误差。本文利用四本硼钠（NaTPB）与米吐尔在酸性条件下可1＋l生成沉淀,以四乙基氯化控为淄定剂,采用交流示波极谱满定法返滴过量Na．TPB,由示波极谱图上TPB切口消失指示滴定终点。本法操作简便快速,终点直观敏锐,应用于fi72和fr76…     

铂微粒/聚3-甲基噻吩修饰电极测定对苯二酚

采用电化学聚合和电化学沉积法制备了负载铂微粒的聚3-甲基噻吩(P3MT)修饰玻碳电极(Pt/P3MT/GCE)。通过循环伏安法研究了对苯二酚在该电极上的电化学行为,并优化了实验参数,在此基础上建立了一种用微分脉冲伏安法直接测定对苯二酚的方法。在酸性溶液中,对苯二酚的氧化峰电流与其浓度在1.0×10-5~8.0×10-3mol·L-1的范围内呈良好的线性关系(r=0.9992),检测限为1.0×10-6mol·L-1,水样中对苯二酚的加标回收率在98%~104%之间。     

Voltammetric Determination of Metol on a Gold Nanoparticle Modified Carbon Molecular Wire Electrode

A carbon molecular wire electrode was fabricated using diphenylacetylene as the modifier and gold nanoparticles were electrodeposited on the surface. The morphology and electrochemical properties of this modified electrode were investigated by scanning electron microscopy and electrochemical impedance spectroscopy. Two well-defined peaks for metol appeared using this gold nanoparticle-modified carbon molecular wire electrode by cyclic voltammetry with a high current response. These results demonstrate a synergistic effect between the gold nanoparticles and the carbon molecular wire electrode resulting in a rapid electrochemical reaction. The electrochemical conditions for metol were optimized on the modified electrode and a detection limit of 0.64?µmol/L and a linear dynamic range between 2.0 to 800.0?µmol/L were obtained. This modified electrode provided good selectivity, high sensitivity, and acceptable reproducibility, demonstrating promise for the determination of metol in the water.     

多巴胺在2-氨基-5-巯基-[1,3,4]三氮唑自组装膜电极上的准可逆行为研究及分析应用

利用新合成的巯基试剂2-氨基-5-巯基-[1，3，4]三氮唑在金电极表面进行了首次自组装，用电化学法和扫描电子显徽镜对自组装膜电极进行了表征。研究了多巴胺在该自组装膜电极上的电化学行为，发现该自组装膜能有效促进多巴胺在电极与溶液之间的电子传递．表现为二电子传递的准可逆行为，电极反应速率常数为0．105cm／s。该自组装膜电极用于多巴胺注射液含量的测定，结果满意。     

巯基取代噻二唑自组装铂电极测定对苯二酚

用自己合成的巯基取代噻二唑试剂对铂电极进行了首次自组装,用电化学方法研究了该电极的电化学性质.研究了对苯二酚在该电极上的电化学行为.实验结果表明,在0.1mol/LKCl溶液中,对苯二酚表现出一种准可逆行为,峰电流对称且峰电位差为80mV,峰电位较之裸铂电极上有较大的降低,峰电流较裸电极大大提高.利用该电极DPV法进行了对苯二酚的电化学测定,峰电流对其浓度在1×10-7~5×10-4mol/L之间成良好的线性关系,检出限为4×10-8mol/L.对对苯二酚模拟品进行了测定,回收率在96.6%-99.6%之间.     

金纳米粒子组装体系中偶联单分子层膜结构的SERS光谱表征与分析

通过分子自组装方法制备4,4′-二硫联吡啶(PySSPy)单分子膜修饰的金电极. 利用所形成的对巯基吡啶自组装单分子膜(SAMs)作为偶联层进行金纳米粒子有序膜的组装. 对该纳米粒子组装体系进行Raman光谱测定, 得到了具有良好信噪比的对巯基吡啶单分子膜的表面增强拉曼散射(SERS)光谱. 在此基础上, 进一步采用电化学现场SERS光谱技术研究了该纳米粒子组装体系的SERS光谱随电位变化的规律. 在该体系稳定的电位范围内表征对巯基吡啶单分子膜的特征谱峰1011与1093 cm^-1、1575与1610 cm^-1以及1206与1215 cm^-1这三对谱峰其强度随着所施加电位的改变呈现出明显的规律性. 分析表明, 偶联单分子层中吡啶环芳香性随着所施加电位的改变而有规律地变化是SERS光谱特征改变的内在原因.     

Electrochemical Studies of Chemically Modified Nanometer‐Sized Electrodes

Self‐assembled monolayers (SAMs) of 4‐aminothiophenol (4‐ATP) has been successfully deposited onto nanometer‐sized gold (Au) electrodes. The cyclic voltammograms obtained on a 4‐ATP SAMs modified electrode show peaks and the peak height is proportional to the scan rate, which is similar to that on an electroactive SAMs modified macro electrode. The electrochemical behavior and mechanism of outer‐sphere electron transfer reaction on the 4‐ATP SAMs modified nanometer‐sized electrode has also been studied. The 4‐ATP SAMs modified electrode is further modified with platinum (Pt) nanoparticles. Electrochemical behaviors show that there is electrical communication between Pt nanoparticles and Au metal on the Pt nanoparticles/4‐ATP SAMs/Au electrode. However, scanning electron microscopic image shows that the Pt nanoparticles are not evenly covered the electrode.     

Label-free aptasensor for platelet-derived growth factor (PDGF) protein

A label-free aptasensor for platelet-derived growth factor (PDGF) protein is reported. The aptasensor uses mixed self-assembled monolayers (SAMs) composed of a thiol-modified PDGF binding aptamer and 6-mercaptohexanol (MCH) on a gold electrode. The SAMs were characterized by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and differential pulse voltammetry (DPV) before and after binding of the protein using [Fe(CN)₆]^3−/4−, a redox marker ion as an indicator for the formation of a protein-aptamer complex. The CVs at the PDGF modified electrode showed significant differences, such as changes in the peak currents and peak-to-peak separation, before and after binding of the target protein. The EIS spectra, in the form of Nyquist plots, were analyzed with a Randles circuit while the electron transfer resistance R_ct was used to monitor the binding of the target protein. The results showed that, without any modification to the aptamer, the target protein can be recognized effectively at the PDGF binding aptamer SAMs at the electrode surface. Control experiments using non-binding oligonucleotides assembled at the electrode surfaces also confirmed the results and showed that there was no formation of an aptamer-protein complex. The DPV signal at the aptamer functionalized electrode showed a linearly decreased marker ion peak current in a protein concentrations range of 1-40 nM. Thus, label-free detection of PDGF protein at an aptamer modified electrode has been demonstrated.     

Electrochemical behavior and voltammetric determination of metol using a multiwall carbon nanotubes modified electrode

Electrochemical behavior of metol, which coexists with p-benzeneiol (HQ) at a glassy-carbon electrode modified with multiwall carbon nanotubes (MWNT/GCE), is studied in the thesis. The results indicate that metol yields a well-defined peak of which two concomitant reductive peaks separate and the potential separation reaches to 178 mV, and that concomitant HQ has almost no interference with the reduction signal of metol. The values of the reductive peak current (I _pc) are found to be linearly related to metol concentration over the range of 8.0 × 10⁻² −1.0 × 10⁻⁵ M, with a detection limit of 5.0 × 10⁻⁶ M. Some common matter has no interference with the determination of metol. Published in Russian in Elektrokhimiya, 2006, Vol. 42, No. 1, pp. 31–35. The text was submitted by the authors in English.     

电容滴定法测定自组装膜表面酸度

利用本实验室自制的电容法时测量装置对巯基丙酸自组装膜的表面酸度进行电容滴定研究，相对于先前的测量和滴定技术。本方法可同时对界面电容值和溶液的PH值进行实时测定。同时对影响电容测定和自组装膜表面pKa值的各种因素进行了详细的讨论。 滴定结果和文献报道相近，证明了测定方法和仪器的可靠性实用性。     

Correlation of the electrochemical reversibility and resolution of the anode and cathode peaks of the electrode processes of hydroquinone and metol on graphite and platinum

Cyclic and direct voltammetry with linear potential sweep was used to study the potential difference of the anode and cathode peaks for hydroquinone and metol in the cyclic voltammograms (CVA) of their individual solutions on the main factors affecting the reversibility of the electrochemical process on electrodes of a graphite-epoxy composite (GEC), namely, the state of the surface of the indicator electrode, the pH of the buffer solution, and the mode of polarization. The surface state of the GEC electrode was affected by its passivation in air for various periods of time; the reversibility of the electrode process was judged by the difference between the anode and cathode potentials on the CVAs of hydroquinone and metol. A correlation was found between the degree of reversibility and the difference of peak potentials for similar electrode processes of hydroquinone and metol on the GEC electrode and other solid electrodes made of graphite materials and platinum.