无氧条件下Pt/TiO_2光催化重整降解—乙醇胺水溶液制氢

以-乙醇胺(以下简称乙醇胺)为电子给体,在无氧条件下进行了Pt/TiO2光催化重整制氢的研究.详细讨论了诸多因素如催化剂表面Pt化学状态、Pt担载量、溶液pH值、乙醇胺溶液浓度等对产氢效率的影响,并用XRD、HNMR、XPS等进行了深入表征,探讨了Pt/TiO2光催化重整降解乙醇胺和产氢的反应,实验表明,利用所制备的光催化剂,可实现在消除水中有机污染物的同时制取氢气的目标.催化剂表面的Pt以Pt0的化学状态存在,有利于析氢;溶液pH值和浓度的变化对产生速率也有一定的影响.同时发现Pt/TiO2光催化重整乙醇胺制氢反应的最佳条件是:Pt的最佳担载量约为0.5％-1.0％;乙醇胺溶液最佳浓度约为0.05 mol·L-1;最佳溶液pH值范围为4-10;氨基取代的羰基类化合物是其主要中间产物.     

在 Pt/TiO2上光催化降解污水中的对氟苯甲酸

在Pt/TiO2存在下,研究了光催化降解对氟苯甲酸的反应.考察了反应时间、溶液初始pH值以及污染物初始浓度对光催化反应的影响.结果表明,溶液的紫外吸光度值随反应时间不断下降;反应7 h时,溶液的TOC去除率达23.2%;反应0.5～2 h内,氟离子平均生成速率为3.53×10-5mol.L-1.h-1;在反应3～7 h内,氟离子平均生成速率为6.22×10-5mol.L-1.h-1.在溶液初始pH值=3.34～3.72时,氟离子生成速率最大,在碱性范围内,氟离子的生成速率为零.当C0(p-fluorobenzoic acid)<1.80×10-3mol.L-1时,光催化降解生成氟离子的速率随着对氟苯甲酸浓度的增大而增大;当C0(p-fluorobenzoic acid)>2.00×10-3mol.L-1时,光催化降解生成氟离子的速率不再随污染物浓度的变化而发生变化.探讨了可能的反应机理.     

无氧条件下Pt/TiO2光催化重整降解一乙醇胺水溶液制氢

以一乙醇胺（以下简称乙醇胺）为电子给体,在无氧条件下进行了Pt/TiO2光催化重整制氢的研究.详细讨论了诸多因素如催化剂表面Pt化学状态、Pt担载量、溶液pH值、乙醇胺溶液浓度等对产氢效率的影响,并用XRD、HNMR、XPS等进行了深入表征,探讨了Pt/TiO2光催化重整降解乙醇胺和产氢的反应, 实验表明,利用所制备的光催化剂, 可实现在消除水中有机污染物的同时制取氢气的目标.催化剂表面的Pt以Pt0的化学状态存在, 有利于析氢;溶液pH值和浓度的变化对产生速率也有一定的影响.同时发现Pt/TiO2光催化重整乙醇胺制氢反应的最佳条件是:Pt的最佳担载量约为0.5％～1.0％;乙醇胺溶液最佳浓度约为0.05 mol•L－1;最佳溶液pH值范围为4～10;氨基取代的羰基类化合物是其主要中间产物.     

铱(III)离子催化铈(IV)离子氧化四氢糠醇的动力学及机理

在酸性介质中用氧化还原滴定法研究了铈(IV)离子在痕量铱(III)离子催化作用下，于298~313 K区间氧化四氢糠醇(THFA)的反应动力学. 结果表明，反应对铈(IV)离子为一级，对铱(III)离子也为一级，对四氢糠醇的表观反应级数为正分数. 准一级速率常数kobs随[H+]增加而增大，而随[HSO₄－]增加而减小. 在氮气保护下，反应能引发丙烯腈聚合，说明在反应中有自由基产生. 通过kobs与[HSO₄－]的依赖关系，找到本反应体系的动力学活性物种是Ce(SO₄)₂，并计算出平衡常数，速控步骤的速率常数及相应的活化参数.     

铱(III)离子催化铈(IV)离子氧化四氢糠醇的动力学及机理

在酸性介质中用氧化还原滴定法研究了铈(IV)离子在痕量铱(III)离子催化作用下,于298￣313K区间氧化四氢糠醇(THFA)的反应动力学.结果表明,反应对铈(IV)离子为一级,对铱(III)离子也为一级,对四氢糠醇的表观反应级数为正分数.准一级速率常数kobs随[H ]增加而增大,而随[HSO-4]增加而减小.在氮气保护下,反应能引发丙烯腈聚合,说明在反应中有自由基产生.通过kobs与[HSO4-]的依赖关系,找到本反应体系的动力学活性物种是Ce(SO4)2,并计算出平衡常数,速控步骤的速率常数及相应的活化参数.     

离子液体中PMBA脱羧反应及界面水影响的电化学SERS研究

基于气-液界面自组装法和转移技术制备了负载Au纳米粒子单层膜的玻碳电极（Au MLF@GC）,并将其用于离子液体-电化学体系界面过程现场的研究.以对巯基苯甲酸（PMBA）的表面等离激元共振（SPR）催化脱羧生成苯硫酚（TP）反应为探针,采用电化学-表面增强拉曼光谱（SERS）技术,通过电位阶跃法研究了其在离子液体体系中的反应动力学行为.结果表明,亲水性离子液体[BMIm]BF4/Au MLF@GC的零电荷电位（pzc）为-0.95 V, PMBA脱羧反应仅在pzc以正区间发生;通过SERS谱峰强度变化以二级反应拟合获得该反应的速率常数,发现其反应速率常数的对数与阶跃后电位呈线性关系;随着体系外加水的含量（摩尔分数）由0增至0.001和0.003,阶跃后发生脱羧反应的起始电位负移,且同一阶跃电位下反应速率常数随着外加水量的增加而增大.     

污染物乙醇胺Pt/TiO2光催化制氢

研究了以污染物乙醇胺为电子给体在Pt/TiO2上光催化生成氢的反应.结果表明,三种乙醇胺都能显著地提高光催化放氢效率,且污染物也被很好降解.研究了反应时间、起始浓度、pH值对光催化放氢和污染物降解的影响.制氢和污染物降解都是在弱碱性(pH为8~9左右)时活性最好.三种乙醇胺浓度对放氢反应的影响,表观上符合Langmuir-Hinshelwood关系式.乙醇胺光催化降解最终产物主要是CO2,H2O和NH3,检测到了中间产物一乙醇胺和甲醛.探讨了可能的反应机理.     

应用扫描电化学显微镜研究水/1,2-二氯乙烷界面上离子诱导的电子转移反应

应用扫描电化学显微镜和微电极技术研究了水/1,2二氯乙烷界面上的反向电子转移反应.分别以K₄Fe(CN)₆和7,7,8,8四氰代二甲基苯醌(TCNQ)作为水相和有机相的电活性物质,通过选择合理的共同离子(TPAs⁺与TBA⁺)来控制界面电位差,实现了这一在热力学上通常不可能实现的反向电子转移反应.利用扫描电化学显微镜给出的正负反馈信息,研究了界面电位差驱动的液/液界面上的电子转移反应,并进一步得到了在不同的共同离子浓度比时,此异相界面反应速率常数k_f为1.3×10^-31.8×10^-2cm/s(共同离子为TBA⁺)和2.5×10^-32.8×10^-2cm/s(共同离子为TPAs⁺).验证了此反应速率常数k_f是由界面电位差所决定的.在此实验条件下,此反应速率常数kf与界面电位差的关系遵守Butler-Volmer公式.     

乙醇胺功能化石墨烯及其PVB复合材料的制备

采用乙醇胺对石墨烯进行改性,一步合成了乙醇胺功能化石墨烯(EFG),探讨了实验条件对该过程的影响.结果表明,乙醇胺在对石墨烯进行功能化的同时还能起到还原氧化石墨烯(GO)的作用,反应产物的吸光度随着乙醇胺的用量、反应温度、反应体系pH值和反应时间的增加而增加,而产物中N元素的含量则随之减小,最佳合成条件为:乙醇胺与GO的质量比为4.0,反应温度50℃,体系pH 7.0,反应时间12 h.然后分别采用溶液共混法和原位还原法,制备了两种不同的EFG/聚乙烯醇缩丁醛(PVB)复合材料,研究了EFG的添加量和加入方式对PVB性能的影响.结果表明,EFG的引入可以极大的提高PVB的导电率、紫外线屏蔽能力和力学性能,且采用原位还原法的效果更好.当EFG添加量为3.0 wt%时,复合材料的导电率较PVB升高了约6~7个数量级;当EFG的添加量仅为1.0 wt%时,复合材料对紫外线的屏蔽能力就到达了90%以上.     

氟离子对TiO2/膨润土光催化降解酸性桃红的影响

研究了在紫外光照射下, 添加氟离子对P25(锐钛矿)和TiO2/膨润土光催化降解酸性桃红(SRB)的影响. 紫外可见光谱测定结果表明无氟的反应体系, pH值越小, 光降解速率越快; pH值固定, 添加氟离子越多, 反应速率越快, 在TiO2/膨润土催化剂上, 当氟离子浓度达到一定程度时, 反应速率不再变化. 在P25和TiO2/膨润土催化剂上, 添加氟离子对H2O2的产生量影响不同, 通过电子顺磁共振(EPR)技术探测到了超氧自由基和羟基自由基, 这两个体系添加氟离子对其产生强度影响不同, 这可能是因为TiO2/膨润土催化剂为层状结构, BET 比表面积较大, 经XRD和TEM测试表明其晶粒直径约为57.9 nm. TiO2/膨润土催化剂连续循环使用11次, 光催化活性基本不变, 这个现象说明TiO2/膨润土催化剂既易于从分散体系中分离出来, 而且其稳定性也好, 它是一个有应用前途的催化剂.     

The kinetics and mechanism of the ferrate(VI) oxidation of hydroxylamines

Aqueous solutions of potassium ferrate(VI) cleanly and rapidly oxidize hydroxylamine to nitrous oxide, N-methylhydroxylamine to nitrosomethane, N-phenylhydroxylamine to nitrosobenzene, and O-methylhydroxylamine to methanol and nitrogen. The kinetics show first-order behavior with respect to each reactant and a two term component representing acid dependent and independent pathways. A general mechanism involving intermediate formation coupled with a two-electron oxidation is proposed.     

The kinetics and mechanism of the oxidation of seleno-DL- methionine by potassium ferrate

The kinetics of the reaction of seleno-DL-methionine with potassium ferrate were investigated under pseudo first-order conditions. The oxidation to the selenoxide is complete within the timeframe of 7.5ms to 2s. The kinetics are first-order in each of the hydrogen ion, selenomethionine and ferrate ion concentrations over the pH range 8.53 to 10.13, but zeroth-order in hydrogen ion concentration at lower pH values. The results are very similar for methionine, except that the overall rate constant is over two orders of magnitude lower. The proposed mechanism involves a rate- determining step between selenomethionine and the protonated ferrate ion.     

Kinetics and Mechanism of the Ferrate Oxidation of Thiosulfate and Other Sulfur-Containing Species

The kinetics of the reaction of ferrate, FeO(4)(2-), with several sulfur-containing species in aqueous media have been investigated, and the results are reported. It was found that, when the reductant is in excess, ferrate rapidly oxidizes thiosulfate to sulfite, benzenesulfinate to benzenesulfonate, methionine to its corresponding sulfoxide, and dimethyl sulfoxide to dimethyl sulfone. The rate law for each reaction is first order with respect to each reactant and first order with respect to the hydrogen ion concentration. A mechanism for each oxidation reaction is discussed.     

Preliminary investigation on the physicochemical properties of calcium ferrate(VI)

Calcium ferrate(VI) powders were synthesized from potassium ferrate(VI), and characterized by titration analysis, elemental analyzer, SEM, XRD, IR, TG and DSC. The results showed that the synthesized sample mainly consists of calcium ferrate(VI), and calcium ferrate(VI) may exist as CaFeO₄ · 2H₂O with a highest obtained purity of 74.9%. The relatively higher Fe(III) impurity and crystalloid water might be responsible for the poor stability of the calcium ferrate(VI) sample. The results of galvanostatic discharge experiments indicated that the calcium ferrate (VI) sample displays better intrinsic rate discharge capability and larger discharge capacity at lower temperatures (⩽15 °C).     

Synthesis of Graphene Oxide by Oxidation of Graphite with Ferrate(VI) Compounds: Myth or Reality?

It is well established that graphene oxide can be prepared by the oxidation of graphite using permanganate or chlorate in an acidic environment. Recently, however, the synthesis of graphene oxide using potassium ferrate(VI) ions has been reported. Herein, we critically replicate and evaluate this new ferrate(VI) oxidation method. In addition, we test the use of potassium ferrate(VI) for the synthesis of graphene oxide under various experimental routes. The synthesized materials are analyzed by a number of analytical methods in order to confirm or disprove the possibility of synthesizing graphene oxide by the ferrate(VI) oxidation route. Our results confirm the unsuitability of using ferrate(VI) for the oxidation of graphite on graphene oxide because of its high instability in an acidic environment and low oxidation power in neutral and alkaline environments.     

高铁酸钾的制备及其在废水治理中的应用进展

高铁酸钾是一种集氧化、絮凝、吸附、杀菌、消毒、除臭功能于一体的新型绿色高效水处理药剂,在废水处理领域具有重要的理论研究和实际应用价值.本文对近年来高铁酸钾的制备方法及其在废水治理中的应用进行综述,重点分析了各制备方法的优缺点,并结合当前最新研究成果对高铁酸钾的工业制备及在废水治理中的应用前景进行了展望.     

The kinetics of oxidation of simple aliphatic sulphur compounds by potassium ferrate

Potassium ferrate (K₂FeO₄) is highly soluble in water and a very strong oxidizing agent^{(1, 2)}. Other properties include a strong bacteriacidal action which has been documented by Murmann and Robinson⁽¹⁾. These characteristics, and others, suggest that potassium ferrate would be useful in the advanced treatment of municipal waste water. The efficiency of oxidation of various organic compounds by potassium ferrate must be investigated before conclusions can be drawn.When K₂FeO₄ is placed into aqueous solution a purple colour is produced which disappears as K₂FeO₄ is reduced. At a spectrophotometric wavelength of 505 nm this affords a convenient method for measuring the decomposition kinetics of K₂FeO₄.Rate constants were obtained by algorithmic analysis of spectral absorbance data by the Cornell method⁽³⁾. This work will present a mechanism of reaction for oxidation of simple aliphatic sulphur compounds by potassium ferrate. The oxidation of simple aliphatic sulphur compounds produces the corresponding sulphoxide or sulphone^{(4, 5)} Compounds studied included dimethyl sulphoxide, diethylsulphide, dimethylsulphone, and 2,2-thiodiethanol.     

光照对高铁酸盐溶液稳定性的影响

The effects of light wave on the stability of fen'ate solution have been examined. The results showed that UV-light accelerates the decomposition of ferrate with decomposition rate 1.6 times as much as that in dark whereas infrared light has only unclear effect on the stability of ferrate, with decomposition rate 1.1 times as much as in dark. The polythene container is found to the best for preservation of ferrate solution in dark.     

A theoretical study of alcohol oxidation by ferrate

The conversion of methanol to formaldehyde mediated by ferrate (FeO(4)2-), monoprotonated ferrate (HFeO4-), and diprotonated ferrate (H2FeO4) is discussed with the hybrid B3LYP density functional theory (DFT) method. Diprotonated ferrate is the best mediator for the activation of the O-H and C-H bonds of methanol via two entrance reaction channels: (1) an addition-elimination mechanism that involves coordination of methanol to diprotonated ferrate; (2) a direct abstraction mechanism that involves H atom abstraction from the O-H or C-H bond of methanol. Within the framework of the polarizable continuum model (PCM), the energetic profiles of these reaction mechanisms in aqueous solution are calculated and investigated. In the addition-elimination mechanism, the O-H and C-H bonds of ligating methanol are cleaved by an oxo or hydroxo ligand, and therefore the way to the formation of formaldehyde is branched into four reaction pathways. The most favorable reaction pathway in the addition-elimination mechanism is initiated by an O-H cleavage via a four-centered transition state that leads to intermediate containing an Fe-O bond, followed by a C-H cleavage via a five-centered transition state to lead to formaldehyde complex. In the direct abstraction mechanism, the oxidation reaction can be initiated by a direct H atom abstraction from either the O-H or C-H bond, and it is branched into three pathways for the formation of formaldehyde. The most favorable reaction pathway in the direct abstraction mechanism is initiated by C-H activation that leads to organometallic intermediate containing an Fe-C bond, followed by a concerted H atom transfer from the OH group of methanol to an oxo ligand of ferrate. The first steps in both mechanisms are all competitive in energy, but due to the significant energetical stability of the organometallic intermediate, the most likely initial reaction in methanol oxidation by ferrate is the direct C-H bond cleavage.     

A Novel Oxidizing Reagent Based on Potassium Ferrate(VI)(1)

A new, efficient preparation has been devised for potassium ferrate(VI) (K(2)FeO(4)). The ability of this high-valent iron salt for oxidizing organic substrates in nonaqueous media was studied. Using benzyl alcohol as a model, the catalytic activity of a wide range of microporous adsorbents was ascertained. Among numerous solid supports of the aluminosilicate type, the K10 montmorillonite clay was found to be best at achieving quantitative formation of benzaldehyde, without any overoxidation to benzoic acid. The roles of the various parameters (reaction time and temperature, nature of the solvent, method of preparation of the solid reagent) were investigated. The evidence points to a polar reaction mechanism. The ensuing procedure was applied successfully, at room temperature, to oxidation of a series of alcohols to aldehydes and ketones, to oxidative coupling of thiols to disulfides, and to oxidation of nitrogen derivatives. At 75 degrees C, the reagent has the capability of oxidizing both activated and nonactivated hydrocarbons. Toluene is turned into benzyl alcohol (and benzaldehyde). Cycloalkanes are also oxidized, in significant (30-40%) yields, to the respective cycloalkanols (and cycloalkanones). Thus, potassium ferrate, used in conjunction with an appropriate heterogeneous catalyst, is a strong and environmentally friendly oxidant.