Synthesis and characterization of diazonium functionalized nanoparticles for deposition on metal surfaces

Silica nanoparticles were surface-functionalized with diazonium groups. The reaction steps leading to the formation of the diazonium functionality were followed with IR and XPS, and the structure of the diazonium-functionalized nanoparticle was confirmed with solid state NMR. Nanoparticle size distribution was determined with DLS, SEM, and TEM. The nanoparticles were then covalently bonded to gold and iron surfaces. Their spatial distribution over the metal surface was analyzed by SEM. Diazonium modification of nanoparticles represents a new method for the covalent attachment of nanoparticles to metal surfaces.     

Preparation of Polymer-Functionalized Iron Oxide Nanoparticles and Their Biomedical Properties

Superparamagnetic iron oxide nanoparticles with narrow size distributions were successfully prepared in large scale by a facile one‐pot synthetic method in the presence of hydrophilic polymers, such as polyethylene glycol diacid (HOOC‐PEG‐COOH) and poly(acrylic acid) (PAA). The as‐prepared products were investigated in detail by powder X‐ray diffraction (XRD), thermogravimetric analyses (TGA), transmission electron microscopy (TEM), high‐resolution transmission electron microscopy (HRTEM), dynamic light scattering (DLS), and vibrating sample magnetometer (VSM). The interaction between polymers and iron oxide nanoparticles was investigated using Fourier transform infrared spectrometry (FT‐IR). The results show that polymers can be attached onto the surface of iron oxide nanoparticle by bridging coordination and monodentate fashion, respectively. The interaction affects iron oxide nanoparticle properties significantly, such as XRD diffraction intensity, hydrodynamic diameter, isoelectric point, and saturation magnetization. Furthermore, the results of in vitro experiments indicated that iron oxide‐PEG‐COOH nanoparticle is more cytotoxic than iron oxide‐PAA nanoparticle due to different coordinating modes.     

Hydrotalcite and nanometric silica as finishing additives to enhance the thermal stability and flame retardancy of cotton

Suspensions of nanoparticles (namely, hydrotalcite and nanometric silica) have been employed during the finishing of cotton in order to improve its thermal stability and/or flame retardancy. The immersion approach has also been coupled to a surface pre-treatment of the textile by cold oxygen plasma in order to load a higher amount of nanoparticles onto fibres. The time of immersion and the resulting distribution of the nanoparticles onto the fibres, evaluated by scanning electron microscopy in combination with elemental analysis, have been thoroughly investigated. The present study has shown that the above parameters are functions of nanoparticle type. Pre-treatment by cold plasma has been found to be more effective than the immersion only. As far as the thermal stability and the combustion behaviour of treated cotton are concerned, the nanoparticles turned out to be able to delay the degradation in air, modifying mechanism and kinetics, and at the same time enhancing the flame retardancy of cotton by increasing the time to ignition and decreasing the heat release rate peak during the combustion. The joint effect of the two nanoparticles has also been evaluated and found more efficient than the effect of single species.     

A one-step homogeneous immunoassay for cancer biomarker detection using gold nanoparticle probes coupled with dynamic light scattering

A one-step homogeneous immunoassay for the detection of a prostate cancer biomarker, free-PSA (prostate specific antigen), was developed using gold nanoparticle probes coupled with dynamic light scattering (DLS) measurements. A spherical gold nanoparticle with a core diameter around 37 nm and a gold nanorod with a dimension of 40 by 10 nm were first conjugated with two different primary anti-PSA antibodies and then used as optical probes for the immunoassay. In the presence of antigen f-PSA in solution, the nanoparticles and nanorods aggregate together into pairs and oligomers through the formation of a sandwich type antibody-antigen-antibody linkage. The relative ratio of nanoparticle-nanorod pairs and oligomers versus individual nanoparticles was quantitatively monitored by DLS measurement. A correlation can be established between this relative ratio and the amount of antigen in solution. The light scattering intensity of nanoparticles and nanoparticle oligomers is several orders of magnitude higher than proteins and other typical molecules, making it possible to detect nanoparticle probes in the low picomolar concentration range. f-PSA in the concentration range from 0.1 to 10 ng/mL was detected by this one-step and washing-free homogeneous immunoassay.     

Gold nanoparticle deposition on Si by destabilising gold colloid with HF

Gold nanoparticles from commercially available colloids were deposited onto a hydrogen-terminated silicon substrate without the use of a polyelectrolyte linker by the addition of HF acid. The deposition density was shown to be controlled over three orders of magnitude by varying the colloid concentration, and finer control is achieved by varying the deposition time. In order to minimise agglomeration, however, we show that deposition times should be minimised since nanoparticle agglomeration increases rapidly over the first 2 min after the addition of HF. To increase nanoparticle density without increasing agglomeration, we show that successive depositions of short times linearly increase the deposition density without increasing the agglomeration of nanoparticles.     

A one-step highly sensitive method for DNA detection using dynamic light scattering

A one-step homogeneous DNA detection method with high sensitivity was developed using gold nanoparticles (AuNPs) coupled with dynamic light scattering (DLS) measurement. Citrate-protected AuNPs with a diameter of 30 nm were first functionalized with two sets of single-stranded DNA probes and then used as optical probes for DNA detection. In the presence of target DNA, the hybridization between target DNA and the two nanoparticle probes caused the formation of nanoparticle dimers, trimers, and oligomers. As a result, the nanoparticle aggregation increased the average diameter of the whole nanoparticle population, which can be monitored simply by DLS measurement. A quantitative correlation can be established between the average diameter of the nanoparticles and the target DNA concentration. This DLS-based assay is extremely easy to conduct and requires no additional separation and amplification steps. The detection limit is around 1 pM, which is 4 orders of magnitude better than that of light-absorption-based methods. Single base pair mismatched DNAs can be readily discriminated from perfectly matched target DNAs using this assay.     

A facile one-pot method to fabricate gold nanoparticle chains with dextran

A biocompatible water-soluble dextran has been used for controllable one-dimensional assembly of gold nanoparticles via a one-pot method.Long gold nanoparticle chains with good dispersion in water could be easily obtained after adding dextran into the mixture of HAuCl 4 and sodium citrate.The measurements of scanning electron microscopy(SEM) and dynamic light scattering(DLS) confirmed the formation of gold nanoparticle chains.The morphology and dispersion properties of gold nanoparticle chains could be tuned by adjustment of the reagent ratio,stirring speed,and reaction time.     

Two-dimensional self-assemblies of silica nanoparticles formed using the "bubble deposition technique"

Two-dimensional silica nanoparticle assemblies were obtained by deposition of bubble made from a surfactant solution containing nanoparticles onto hydrophobic silicon substrate. The morphologies of the nanoparticle assemblies can be finely controlled by several experimental parameters, including surfactant concentration, nanoparticle concentration, and deposition time. Monolayer of nanoparticles with surface coverage of about 100% can be obtained under appropriate conditions. The method can also be applied to another hydrophobic substrate, HMDS (hexamethyldisilazane)-modified silicon substrate. Furthermore, it can be applied directly to lithography patterned substrates, meaning a high compatibility with the well-developed conventional top-down approaches to nanodevices. This bubble deposition technique is expected to be a promising method in the field of nano-object assembly and organization and has great application potentials.     

Study and modeling of iron hydroxide nanoparticle uptake by AOT (w/o) microemulsions

Control over nanoparticle size is a key factor which labels a given preparation technique successful. When organic reactions are mediated by ultradispersed catalysts, the concentration of the colloidal nanoparticle catalysts and their stability become key factors as well. In this study, variables affecting iron hydroxide nanoparticle size, stability, and maximum possible colloidal concentration in AOT/water/isooctane microemulsions were investigated. Iron hydroxide was prepared in single microemulsions by first solubilizing iron chloride powder in the water pools, followed by addition of aqueous NaOH. Upon addition of NaOH, Fe(OH)3 nanoparticles stabilized in the water pools formed in addition to bulk precipitate of Fe(OH)3. The time-invariant concentration of the stabilized Fe(OH)3 is defined as the nanoparticle uptake, and it corresponds to the maximum possible concentration of the colloidal nanoparticles. The effect of the following variables on the nanoparticle uptake and size distribution was investigated: mixing time; surfactant concentration; water to surfactant mole ratio; and the initial concentration of the precursor salt. At 300 rpm of mixing a constant uptake of iron hydroxide nanoparticles was achieved in about 2 h and further mixing had limited effect on the nanoparticle uptake and particle size. An optimum R was found for which a maximum nanoparticle uptake was obtained. Nanoparticle uptake increased linearly with the surfactant concentration and displayed a power function with the initial concentrations of the precursor salt. The surface area/g of the nanoparticles was much higher than literature values, however, following a trend opposite to that of the nanoparticle uptake. The surface area/unit volume of the microemulsion, on the other hand, followed the same trend as the nanoparticle uptake. The particle size increased as R and/or the surfactant concentration increased. A mathematical model based on correlations for water uptake by Winsor type II microemulsions accurately accounted for the effect of the aforementioned variables on the nanoparticle uptake.     

Role of Magnetite Nanoparticles Size and Concentration on Hyperthermia under Various Field Frequencies and Strengths

Magnetite (Fe₃O₄) nanoparticles were synthesized using the chemical coprecipitation method. Several nanoparticle samples were synthesized by varying the concentration of iron salt precursors in the solution for the synthesis. Two batches of nanoparticles with average sizes of 10.2 nm and 12.2 nm with nearly similar particle-size distributions were investigated. The average particle sizes were determined from the XRD patterns and TEM images. For each batch, several samples with different particle concentrations were prepared. Morphological analysis of the samples was performed using TEM. The phase and structure of the particles of each batch were studied using XRD, selected area electron diffraction (SAED), Raman and XPS spectroscopy. Magnetic hysteresis loops were obtained using a Lakeshore vibrating sample magnetometer (VSM) at room temperature. In the two batches, the particles were found to be of the same pure crystalline phase of magnetite. The effects of particle size, size distribution, and concentration on the magnetic properties and magneto thermic efficiency were investigated. Heating profiles, under an alternating magnetic field, were obtained for the two batches of nanoparticles with frequencies 765.85, 634.45, 491.10, 390.25, 349.20, 306.65, and 166.00 kHz and field amplitudes of 100, 200, 250, 300 and 350 G. The specific absorption rate (SAR) values for the particles of size 12.2 nm are higher than those for the particles of size 10.2 nm at all concentrations and field parameters. SAR decreases with the increase of particle concentration. SAR obtained for all the particle concentrations of the two batches increases almost linearly with the field frequency (at fixed field strength) and nonlinearly with the field amplitude (at fixed field frequency). SAR value obtained for magnetite nanoparticles with the highest magnetization is 145.84 W/g at 765.85 kHz and 350 G, whereas the SAR value of the particles with the least magnetization is 81.67 W/g at the same field and frequency.     

Tribo-corrosion behavior of Zn-Ni-Cu and Zn-Ni-Cu-TiB2 coated mild steel

In this investigation , Zn-Ni-Cu and Zn-Ni-Cu-TiB₂ were coated on a mild steel specimen using a high velocity oxy fuel thermal spray (HVOF) process. The surface morphology and coated powder distribution of coated specimens were characterized using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), and X-ray-Elemental mapping. The pin-on-disc (ASTM G99-17) method was used to examine the wear resistance of the coated and uncoated mild steel specimens. Both coated Zn-Ni-Cu and Zn-Ni-Cu-TiB2 on mild steel saw reduced wear volume loss than uncoated mild steel. The coated samples of Zn-Ni-Cu and Zn-Ni-Cu-TiB2 on Mild Steel were put through a scratch test to determine the adhesion strength of the coating with the substrate. The adhesion strength of coated Zn-Ni-Cu and Zn-Ni-Cu TiB2 mild steel was higher than that of untreated mild steel, indicating a solid link between the coating and substrate and minimal delamination. Using the Vickers hardness test to measure the hardness caused by the coating, it was shown that coated samples of Zn-Ni-Cu and Zn-Ni-Cu-TiB2 coated mild steel had significantly higher hardness than uncoated mild steel. Using ASTM G1-03 and ASTM G-31 standards, a 0.2 M HCl immersion cycle test was conducted for 28 days to test the corrosion resistance of coatings in an acidic media (672Hrs). When compared to Zn-Ni-Cu and Zn-Ni-Cu-TiB2 coated mild steel, the weight loss for the uncoated mild steel was significantly larger. Additionally, XRD examination showed that coated samples had less rust on their surface than uncoated samples. Both Zn-Ni-Cu and Zn-Ni-Cu-TiB2 on Mild Steel were anti-corrosive, as evidenced by increased corrosion potential and reduced corrosion current density when compared to uncoated mild steel, according to electrochemical impedance spectroscopy (EIS)/Tafel study in 0.2 MHCl. The outcomes of each test were very encouraging and demonstrated the durability of these coatings against wear and corrosion.     

Complex formation between cationically modified gold nanoparticles and DNA: an atomic force microscopic study

Atomic force microscopy has been used for direct visualization of the wrapping of DNA around 30-nm-sized functionalized gold nanoparticles for the first time. The morphology of the complexes seems to be dictated by the relative concentration of the nanoparticles and DNA. A higher concentration of the former leads to the formation of a network of nanoparticles assembled on DNA. This assembly pattern seems to be significantly different from the manner in which cationically modified gold nanoparticles of smaller size (< 5 nm) arrange linearly on DNA, as shown in the literature. A DNA-gold nanoparticle can be developed as a model system for in vitro studies on the mechanism of DNA condensation and also for developing novel methods of nanoparticle self-assembly on the DNA template.     

On the measurement of gold nanoparticle sizes by the dynamic light scattering method

The application of the dynamic light scattering (DLS) method for determining the size distribution of colloidal gold nanoparticles in a range of 1–100 nm is discussed. It is shown that rotational diffusion of nonspherical strongly scattering particles with sizes of larger than 30–40 nm results in the appearance of a false peak in a size range of about 5–10 nm. In this case, the uncritical application of the DLS method may yield particle volume or number size distributions different from those obtained by transmission electron microscopy. For weakly scattering particles with diameters of smaller that 20 nm, the DLS method demonstrates an additional peak of intensity distribution in the region of large sizes that is related to particle aggregates or byproduct particles rather than individual nanoparticles. Practical methods for solving the problem of false peaks are discussed. It is established that the width of the DLS distribution does not correspond to transmission electron microscopy data and is overestimated. The advantages and drawbacks of the methods are compared and it is noted that, at present, the DLS method is the only instrument suitable for nonperturbative and sensitive diagnostics of relatively slow aggregation processes with characteristic times on the order of 1 min. In particular, this method can be used to diagnose gold nanoparticle conjugate aggregation initiated by biospecific interactions on their surface.     

Elaboration of chitosan-coated nanoparticles loaded with curcumin for mucoadhesive applications

Polycaprolactone (PCL) nanoparticles decorated with a mucoadhesive polysaccharide chitosan (CS) containing curcumin were developed aiming the buccal delivery of this drug. These nanoparticles were prepared by the nanoprecipitation method using different molar masses and concentrations of chitosan and concentrations of triblock surfactant poloxamer (PEO-PPO-PEO), in order to optimize the preparation conditions. Chitosan-coated nanoparticles showed positive surface charge and a mean particle radius ranging between 114 and 125 nm, confirming the decoration of the nanoparticles with the mucoadhesive polymer, through hydrogen bonds between ether and amino groups from PEO and CS, respectively. Dynamic Light Scattering (DLS) studies at different scattering angles and concentrations have shown that the nanoparticles are monodisperse (polydispersity indices were lower than 0.3). The nanoparticle systems were also examined with Nanoparticle Tracking Analysis (NTA), and the results were in good agreement with those obtained by DLS. Colloidal systems showed mean drug content about 460 μg/mL and encapsulation efficiency higher than 99%. Finally, when coated with chitosan, these nanoparticles show a great ability to interact with mucin indicating also their suitability for mucoadhesive applications.     

Synthesis of nanoparticle-cored dendrimers by convergent dendritic functionalization of monolayer-protected nanoparticles

This article presents a synthesis method for nanoparticle-cored dendrimers (NCDs), which have dendritic architectures around a monolayer-protected gold nanoparticle. The synthesis method is based on a strategy in which the synthesis of monolayer-protected nanoparticles is followed by adding dendrons on functionalized nanoparticles by a single coupling reaction. NMR spectroscopy, IR spectroscopy, and thermogravimetric analysis (TGA) characterizations confirmed the successful coupling reaction between dendrons with different generations ([G1], [G2], and [G3]) and COOH-functionalized nanoparticles ( approximately Au201L71). The dendrimer wedge density also could be controlled by reacting nanoparticles having different loading of COOH groups ( approximately 60 and approximately 10% COOH of the 71 ligands per gold nanoparticle) with functionalized dendrons. Transmission electron microscope results showed that this synthesis strategy maintains the average size of the nanoparticle core during dendron coupling reactions. This control over the composition and core size makes the systematic study of NCDs with different generations possible. The chemical stability of NCDs was found to be affected by dendron generation around the nanoparticle core. The current-potential response of NCD films on microelectrode arrays exhibited better electrical conductivity for NCDs with lower dendron generation.     

Water-soluble iron oxide nanoparticles with high stability and selective surface functionality

The water dispensability and stability of high quality iron oxide nanoparticles synthesized in organic solvents are major issues for biomedical and biological applications. In this paper, a versatile approach for preparing water-soluble iron oxide nanoparticles with great stability and selective surface functionality (-COOH, -NH(2), or -SH) was demonstrated. The hydrophobic nanoparticles were first synthesized by the thermal decomposition of an iron oleate complex in organic solvent. Subsequently, the hydrophobic coatings of nanoparticles were replaced with poly(acrylic acid) , polyethylenimine, or glutathione, yielding charged nanoparticles in aqueous solution. Two parameters were found to be critical for obtaining highly stable nanoparticle dispersions: the original coating and the surfactant-to-nanoparticle ratio. These charged nanoparticles exhibited different stabilities in biological buffers, which were directly influenced by the surface coatings. This report will provide significant practical value in exploring the biological or biomedical applications of iron oxide nanoparticles.     

Size dependent catalysis with CTAB-stabilized gold nanoparticles

CTAB-stabilized gold nanoparticles were synthesized by applying the seeding-growth approach in order to gain information about the size dependence of the catalytic reduction of p-nitrophenol to p-aminophenol with sodium borohydride. Five different colloidal solutions of stabilized gold nanoparticles have been characterized by TEM, AFM, UV-Vis, SAXS, and DLS for their particle size distributions. Gold nanoparticles (mean sizes: 3.5, 10, 13, 28, 56 nm diameter) were tested for their catalytic efficiency. Kinetic data were acquired by UV-Vis spectroscopy at different temperatures between 25 and 45 °C. By studying the p-nitrophenol to p-aminophenol reaction kinetics we determined the nanoparticle size which is needed to gain the fastest conversion under ambient conditions in the liquid phase. Unexpectedly, CTAB-stabilized gold nanoparticles with a diameter of 13 nm are most efficient.     

Synthesis, photoluminescence, and adsorption of CdS/dendrimer nanocomposites

CdS/dendrimer nanocomposites can be synthesized from methanolic Cd(2+) and S(2-) with amine-terminated polyamidoamine dendrimers of generation 8 (G8NH(2)) as stabilizers. By controlling the preparation conditions, nanoparticles with diameters < or = 2 nm can be obtained with a narrow size distribution. They show blue photoluminescence at approximately 450 nm. We studied the effects of various additives on the photoluminescence and elucidated its mechanism. Stable aggregates of two to three G8NH(2) molecules with several CdS nanoparticles form; the particles are located at the surface of the G8NH(2) molecules. The adsorption of the CdS/G8NH(2) nanocomposites on flat substrate surfaces is determined by the substrate chemistry. The hydrophilic nature of G8NH(2) results in weak affinity to graphite but strong affinity to hydroxy-terminated substrates such as mica, oxidized silicon wafers, and carboxylate-terminated monolayers. Patterning of nanocomposites on these hydrophilic substrates is achieved by the microcontact printing method. We propose to use only one molecule, a large dendrimer, to control the nanoparticle formation and also the immobilization of the synthesized nanoparticle/dendrimer composites.     

Green biosynthesis,characterization, and cytotoxic effect of magnetic iron nanoparticles using Brassica Oleracea var capitata sub var rubra (red cabbage) aqueous peel extract

The green method of nanoparticle synthesis, which is an environment and living-friendly method, is an updated subject that has appeared as an alternative to conventional methods such as physical and chemical synthesis. In this presented study, the green synthesis of magnetic iron oxide nanoparticles (IONPs) from iron (III) chloride by using Brassica oleracea var. capitata sub.var. rubra aqueous peel extract has been reported. The prepared IONPs were characterized with fourier-transform infrared spectroscopy (FT-IR), ultraviolet-visible spectroscopy (UV-VIS), zeta potential, scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX). The cytotoxic effects of IONPs on MCF-7 breast cancer cell line were studied by MTT assay, and migrative effect of its were carried out by the wound healing assay. It was found that the mean particle size of IONPs was 675 ± 25 nm, and the polydispersity index was 0.265 PDI. It was also determined that these nanoparticles had an anti-proliferative impact on the MCF-7 breast cancer cell line depending on the dosage. Characterization results support the successful synthesis of nanoparticles, and the dose-dependent cytotoxic effects of nanoparticles on MCF-7 cells also make it a potential chemotherapeutic agent for breast cancer treatment.     

A biologically friendly single step method for gold nanoparticle formation

There has been a keen interest for developing a biologically friendly approach for the preparation of gold nanoparticles for their application reasons. A biocompatible, quick and single step method is established for the preparation of gold nanoparticles in lecithin (Egg phosphatidylcholine)/water systems where lecithin itself acts as a reductant for hydrogen tetrachloro aurate (HAuCl(4)) to form the gold nanoparticles. Small gold nanoparticles (5-7 nm in diameter) were prepared in lamellar phases formed by lecithin within 6-7h of HAuCl(4) addition. Sonication of aqueous mixture of lecithin/HAuCl(4) reduces the time of reduction process to seconds when a sonicator with probe (100 W) is used. Most of the particles are found attached to lecithin structures and are comparatively large in size. Some 10nm particles are found attached to small lecithin vesicles (～100 nm) formed during sonication. The nanoparticles formed were stabilized by an anionic surfactant sodium dodecylsulfate (SDS) which proved to be a good stabilizer, the nanoparticles being stable up to six months. To the best of our knowledge, this is the first report where a biological surfactant lecithin itself has acted as a reductant and no other chemical reductants were required for the gold nanoparticle formation. Particles were characterized by Uv-vis spectroscopy, transmission electron microscopy (TEM) and dynamic light scattering (DLS). Lamellar phases were characterized by a polarizing microscope.