Effect of pressure on transport properties of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate

The self-diffusion coefficients (D) of the cation and anion in the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM]PF6) have been determined together with the electrical conductivity (kappa) under high pressure. All three quantities strongly decrease with increasing pressure to approximately 20% of their atmospheric pressure values at 200 MPa. D(PF6-) is always less than D([BMIM]+), despite the larger van der Waals volume of the cation. The pressure effect on the transport coefficients is discussed in terms of velocity correlation coefficients (VCCs or fij), the Nernst-Einstein equation (ionic diffusivity-conductivity), and the fractional form of the Stokes-Einstein relation (viscosity-conductivity and viscosity-diffusivity). It was found that the VCCs for the cation-cation, anion-anion, and cation-anion pairs are all negative and strongly pressure-dependent, increasing (becoming less negative) with increasing pressure. However, when the values of the VCCs for a given isotherm are normalized relative to the corresponding atmospheric pressure values, they collapse onto a single curve, as might be expected because the pressure should affect the interionic velocity correlations in the same way for each type of interaction. These isothermal curves can be represented by the form exp(alphap + betap2). The Nernst-Einstein deviation parameter, Delta, which depends on the differences between the like-like ion and unlike ion VCCs (f++ + f-- - 2f+-), is very nearly constant under the conditions examined. The diffusion and molar conductivity (Lambda) data are found to fit fractional forms of the Stokes-Einstein relationship with the viscosity, (LambdaT) proportional, variant (T/eta)t and Di proportional, variant (T/eta)t , with t = (0.92 +/- 0.05), independent of both temperature and pressure within the ranges studied and common to the three independently determined properties.     

咪唑离子液体对铜在硫酸溶液中的缓蚀作用

采用动电位极化和电化学阻抗谱技术研究了三种新型烷基咪唑离子液体, 1-丁基-3-甲基咪唑硫酸氢盐([BMIM]HSO₄), 1-已基-3-甲基咪唑硫酸氢盐([HMIM]HSO₄), 1-辛基-3-甲基咪唑硫酸氢盐([OMIM]HSO₄), 对铜在0.5 mol·L_-1 H₂SO₄溶液中的缓蚀作用. 实验结果表明: 咪唑离子液体能有效抑制铜在硫酸溶液中的腐蚀, 相同浓度下的缓蚀效率大小顺序为[OMIM]HSO₄>[HMIM]HSO₄>[BMIM]HSO₄. 动电位极化表明三种咪唑化合物的加入对铜的阴阳极腐蚀过程均有抑制作用, 属于混合型缓蚀剂. 电化学阻抗谱用带两个常相位原件的等效电路对含两个时间常数的体系进行拟合, 发现咪唑化合物的添加会引起电荷传递电阻和双电层电容等阻抗参数的变化, 表明此类化合物通过吸附于铜电极与溶液界面起到缓蚀作用, 且这种吸附符合Langmuir吸附等温关系. 吸附过程热力学计算说明咪唑化合物在铜表面发生了自发的物理吸附.     

The thermochemistry of solvation of imidazolium-based ionic liquids in benzene

ABSTRACT

The present work is devoted to the thermochemical study of solvation of ionic liquids (IL) in benzene. The solution enthalpies of 1-ethyl-3-methylimidazolium tricyanomethanide [EMIM][C(CN)₃], 1-butyl-3-methylimidazolium tetrafluoroborate [BMIM][BF₄], 1-hexyl-3-methylimidazolium hexafluorophosphate [HMIM][PF₆], 1-octyl-3-methylimidazolium tetrafluoroborate [OMIM][BF₄], 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [EMIM][NTf₂], 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [BMIM][NTf₂] and 1-butyl-3-methylimidazolium trifluoromethanesulfonate [BMIM][TfO] in benzene were measured. The solvation enthalpies of imidazolium-based IL were calculated. Molar refractions of imidazolium-based IL form literature data on density and refractive indexes of IL were also calculated. The linear correlation between solvation enthalpy and molar refraction of IL was observed. This correlation can be used to calculate the vaporization enthalpy of imidazolium-based IL from solution calorimetry data.     

羟基功能化离子液体与溶菌酶相互作用的研究

采用荧光光谱和紫外吸收光谱研究了羟基功能化离子液体1-(1,2-二羟基丙基)-3-甲基咪唑氯盐([2,3-dhpmim]Cl)、1-(1,2-二羟基丙基)-3-甲基咪唑四氟硼酸盐([2,3-dhpmim]BF4)、1-(1,2-二羟基丙基)-3-甲基咪唑六氟磷酸盐([2,3-dhpmim]PF6)与溶菌酶的相互作用。研究发现此3种离子液体对溶菌酶的荧光猝灭均为静态猝灭;同步荧光显示离子液体与溶菌酶肽链上的色氨酸残基作用,色氨酸残基微环境发生改变;结合常数和结合位点数按照[2,3-dhpmim]Cl、[2,3-dhpmim]BF4、[2,3-dhpmim]PF6顺序依次增大,并随温度的升高而增大。     

Synthesis and formation mechanism of nanoneedles and nanorods of manganese oxide octahedral molecular sieve using an ionic liquid

Single-crystalline cryptomelane-type manganese oxide octahedral molecular sieve (OMS-2) nanoneedles and nanorods were prepared by a solution-phase approach in the presence of an ionic liquid 1-n-butyl-3-methylimidazolium tetrafluoroborate ([BMIM]BF4). [BMIM]BF4 can act as a cosolvent, structure-directing agent, and reducing reagent in the reaction system. Based on the redox reaction of MnCl2 and KMnO4 in the mixed solvents of water and [BMIM]BF4, the formation of OMS-2 nanoneedles followed the rolling mechanism with lamellae as an intermediate. However, the direct reaction of KMnO4 with [BMIM]BF4 resulted in the formation of OMS-2 nanorods with diameters as small as 3-6 nm. The formation mechanism of OMS-2 nanostructures was discussed.     

Protein structure and dynamics in ionic liquids. Insights from molecular dynamics simulation studies

We present in this work the first molecular simulation study of an enzyme, the serine protease cutinase from Fusarium solani pisi, in two ionic liquids (ILs): 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6]) and 1-butyl-3-methylimidazolium nitrate ([BMIM][NO(3)]). We tested different water contents in these ILs at room temperature (298 K) and high temperature (343 K), and we observe that the enzyme structure is highly dependent on the amount of water present in the IL media. We show that the enzyme is preferentially stabilized in [BMIM][PF6] at 5-10% (w/w) (weight of water over protein) water content at room temperature. [BMIM][PF6] renders a more nativelike enzyme structure at the same water content of 5-10% (w/w) as previously found for hexane, and the system displays a similar bell-shape-like dependence with the water content in the IL media. [BMIM][PF6] is shown to increase significantly the protein thermostability at high temperatures, especially at low hydration. Our analysis indicates that the enzyme is less stabilized in [BMIM][NO(3)] relative to [BMIM][PF6] at both temperatures, most likely due to the strong affinity of the [NO(3)]- anion toward the protein main chain. These findings are in accordance with the experimental knowledge for these two ionic liquids. We also show that these ILs "strip off" most of the water from the enzyme surface in a degree similar to that found for polar organic solvents such as acetonitrile, and that the remaining waters at the enzyme surface are organized in many small clusters.     

基于金属介导和离子液体的新型绿原酸印迹整体柱的制备及评价

选用1-乙烯基-3-乙基咪唑四氟硼酸盐([VElm]BF4,一种离子液体)作为功能单体,以Co2+为介导离子,结合1-丁基-3-甲基咪唑四氟硼酸盐([BMIM]BF4)/二甲基亚砜(DMSO)二元致孔体系制备了绿原酸印迹整体柱。经过对制备参数的考察,确定最佳比例为绿原酸:Co2+:[VElm]BF4:EDMA(乙二醇二甲基丙烯酸酯)(摩尔比)=1:1:5:20,[BMIM]BF4:DMSO=3:1(V/V),最大印迹因子达2.10。通过优化色谱条件,最终在乙腈:20 mmol/L乙酸钠缓冲液(pH 4.2)=70:30(V/V)时实现了绿原酸及其类似物的完全分离。由此可见,以离子液体为功能单体及致孔剂,在金属介导策略下制备的分子印迹聚合物可实现绿原酸的特异性识别及分离。     

Molecular Dynamic Study of the Behavior of Confined [BMIM][PF6] Ionic Liquids: Pore Size Dependence

Russian Journal of Physical Chemistry A - This work aimed to investigate the structural and dynamical properties of ionic liquid (IL) 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6])...     

Surface tension of binary mixtures of imidazolium and ammonium based ionic liquids with alcohols, or water: cation, anion effect

The surface tensions were measured at atmospheric pressure, with use of a ring tensiometer, of a series of alcoholic solutions of closely related ionic liquids: 1-methyl-3-methylimidazolium methylsulfate, [MMIM][CH3SO4] in alcohol (methanol, or ethanol, or 1-butanol at 298.15 K), 1-butyl-3-methylimidazolium methylsulfate, [BMIM][CH3SO4] in alcohol (methanol, or ethanol, or 1-butanol at 298.15 K), 1-butyl-3-methylimidazolium octylsulfate, [BMIM][OcSO4] in alcohol (methanol, or 1-butanol at 298.15 K) and of 1-hexyloxymethyl-3-methylimidazolium tetrafluoroborate, [C6H(13)OCH2MIM][BF4], 1,3-dihexyloxymethylimidazolium tetrafluoroborate, [(C6H13OCH2)2IM][BF4] in alcohol (methanol, or 1-butanol, or 1-hexanol at 308.15 and 318.5 K) and hexyl(2-hydroxyethyl)dimethylammonium bromide, C6Br in 1-octanol at 298.15 K. The set of ammonium ionic liquids of different cations and anions (C2Br, C2BF4, C2PF6, C2N(CN)2, C3Br, C4Br and C6Br) was chosen to show the influence of small amount of the ammonium ionic liquid on the surface tension of water at 298.15 K. The influence of the cation, or anion alkyl chain length on the properties under study (densities and surface tension) was tested.     

Measurement of vapor–liquid equilibria (VLE) and excess enthalpies (H) of binary systems with 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide and prediction of these properties and γ using modified UNIFAC (Dortmund)

Vapor–liquid equilibria (VLE) and excess enthalpies (H^E) were measured for a variety of alkanes, alkenes, aromatics, alcohols, ketones and water in several ionic liquids, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [EMIM]⁺[BTI]⁻, 1-butyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)imide [BMIM]⁺[BTI]⁻, 1-hexyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)imide [HMIM]⁺[BTI]⁻ and 1-octyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)imide [OMIM]⁺[BTI]⁻, covering the temperature range from 323.15 to 413.15 K. The new data were used together with the already available experimental data for imidazolium compounds to fit the required group interaction parameters for modified UNIFAC (Dortmund). The results show that in the future modified UNIFAC (Dortmund) can be applied successfully also for systems with ionic liquids.     

吡咯烷酮酸性离子液体中硼酸酯的催化合成

研究了硼酸与频哪醇和环己醇在离子液体1-甲基-2-吡咯烷酮硫酸氢盐（[Hnmp]HSO4）、1-丁基-3-甲基咪唑四氟硼酸盐（[Bmim]BF4）及1-丁基-3-甲基咪唑六氟磷酸盐([Bmim]PF6)中生成2-环己氧基-4,4,5,5-四甲基-1,3,2-二氧硼烷的酯化反应。 考察了不同离子液体、反应温度、反应时间和离子液体与反应物物质的量比等对反应的影响。 结果表明,当n(硼酸)∶n(频哪醇)∶n(环己醇)∶n([Hnmp]HSO4)=1∶1∶1∶1,反应温度为70 ℃和反应时间为4 h时,硼酸酯的产率为72.5%,离子液体重复使用4次,催化活性无明显降低。     

离子液体[BMIM]PF6中铬的电沉积行为简

以一氯丁烷、N-甲基咪唑和KPF6为原料,合成了1-丁基-3-甲基咪唑六氟磷酸盐离子液体([BMIM]PF6),用红外光谱(IR)对产物进行了结构分析. 用循环伏安法测试该离子液体在85 ℃下的电化学窗口为4.7 V. 考察了[BMIM]PF6-Cr(Ⅲ)电解液的电化学行为,结果表明,在85 ℃下Cr(Ⅲ)的还原过程是受扩散控制的一步还原不可逆过程,Cr(Ⅲ)的传递系数α=0.023,阴极扩散系数D0=1.142×10-6 cm2/s. 在85 ℃和-1.5 V条件下,用恒电势法在铜片上电沉积Cr(Ⅲ),并通过扫描电子显微镜(SEM)观察了铜片上镀层的表面结构,发现该镀层呈颗粒状,且颗粒的体积随沉积时间的延长而增大. X射线能量色散谱(EDS) 和X射线粉末衍射(XRD)测试结果表明,该镀层为无定形的金属铬.     

Solution structures of 1-butyl-3-methylimidazolium hexafluorophosphate ionic liquid saturated with CO2: Experimental evidence of specific anion-CO2 interaction

X-ray diffraction measurements for 1-butyl-3-methylimidazolium hexafluorophosphate ionic liquid ([BMIM][PF6])-CO2 systems were carried out at high pressures with a newly developed polymer cell. The intermolecular distribution functions (g(inter)(r)) were obtained at 25 degrees C for neat [BMIM][PF6] and its solutions saturated with CO2 at 4 and 15 MPa, where the mole fractions (x) of CO2 correspond to 0.5 and 0.7, respectively. In g(inter)(r) for x = 0.5, two peaks appeared at around 2.8 and 3.2 A. These two peaks in g(inter)(r) appreciably increased for x = 0.7; moreover, there was another peak observed at approximately 3.8 A. Only assuming the correlations between CO2 and [PF6]-, it is reasonably determined that the nearest-neighbor P([PF6]-). . .C(CO2) distances are 3.57 and 3.59 A with the coordination numbers being 1.8 and 4.0 for x = 0.5 and 0.7, respectively. It is concluded that CO2 molecules are preferentially solvated to the [PF6]- anion.     

Dynamic wetting of a fluoropolymer surface by ionic liquids

The spontaneous spreading of ionic liquids on a fluoropolymer surface (Teflon AF1600) in air is investigated by high-speed video microscopy. Six ionic liquids (EMIM BF(4), BMIM BF(4), OMIM BF(4), EMIM NTf(2), BMIM NTf(2) and HMIM NTf(2)) are used as probe liquids. The dependence of the dynamic contact angle on contact line velocity is interpreted with a hydrodynamic model and a molecular-kinetic model. The usefulness of the hydrodynamic model is rather limited. There is a good correspondence between the molecular dimensions of the liquids and the physical parameters of the molecular-kinetic model. The viscous and molecular-kinetic contributions to energy dissipation are calculated, revealing that energy is dissipated in the bulk as well as at the contact line during dynamic wetting. There are wide ramifications of these results in areas ranging from lubrication and biology to minerals processing and petroleum recovery.     

Viscosity of ionic liquid mixtures of 1-alkyl-3-methylimidazolium hexafluorophosphate + CO2

The viscosities of the mixtures 1-hexyl-3-methylimidazolium hexafluorophosphate ([HMIM][PF₆]) + CO₂ and 1-octyl-3-methylimidazolium hexafluorophosphate ([OMIM][PF₆]) + CO₂ were measured with a rolling ball viscometer. The CO₂ mole fraction for one mixture ranged up to 0.434 and the other up to 0.447. The viscosities were measured at 293.15-353.15 K and 10-20.0 MPa. The experimental uncertainty in viscosity was estimated to be within ±3.0%. The experimental data were compared with McAllister's three-body model, which correlated with the experimental data within average absolute deviations of 5.9%.     

Dynamically coated silica monolith with ionic liquids for capillary electrochromatography

An ionic liquid, 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF4]) was introduced as dynamic coating of a silica monolithic column for capillary electrochromatography of phenols and nucleoside monophosphates. The run-to-run and column-to-column repeatability of migration time for six phenols were satisfactory on this column with relative standard deviation values less than 0.90 and 4.31%, respectively. Anodic electroosmotic flow (EOF) was observed, which increased with the increase of [BMIM][BF4] concentration within 120 mM and when [BMIM][BF4] concentration was above 120 mM, EOF leveled off due to the saturation of [BMIM][BF4] on the monolith. Efficient separation of phenols and nucleoside monophosphates on this dynamically coated monolithic column was obtained, compared with a dynamically coated fused-silica column and unmodified silica monolithic column. The retention behavior of uncharged phenols is mainly manipulated by hydrophobic interactions due to the presence of butyl groups, and that of nucleoside monophosphates is governed by the electrostatic attraction mechanism based on the interaction between positively charged [BMIM][BF4] moieties and negatively charged phosphate groups. In addition, silica matrix also contributes to the separation resolution.     

Structures of ionic liquids with different anions studied by infrared vibration spectroscopy

We investigated the structures of ionic liquids (1-butyl-3-methylimidazolium iodide [BMIM][I] and 1-butyl-3-methylimidazolium tetrafluoroborate [BMIM][BF4]) and their aqueous mixtures using attenuated total reflection (ATR) infrared absorption and Raman spectroscopy. The ATR spectrum in the CHx (x = 1, 2, 3) vibration region from 2800 to 3200 cm-1 was very different between [BMIM][BF4] and [BMIM][I] even though all the spectral features in this region were from the butyl chain and the imidazolium ring of the same cation. The spectrum did not change appreciably irrespective of the water concentration for [BMIM][BF4], whereas the spectrum from [BMIM][I] showed significant changes as the water concentration was increased, especially in CH-vibration modes from the imidazolium ring. For very diluted solutions both aqueous mixtures of [BMIM][I] and [BMIM][BF4] showed very similar spectra. Mixing of [BMIM][I] with heavy water (D2O) facilitated the isotopic exchange of the proton attached to the most acidic carbon of the imidazolium ring into deuterium from D2O, whereas even prolonged exposure to D2O did not induce any isotopic exchange for [BMIM][BF4]. Raman spectra around 600 cm(-1) indicative of the butyl chain conformation also changed differently as the water concentration was increased between [BMIM][I] and [BMIM][BF4]. These differences are considered to come from the variation in the position of the anion, where I- is expected to be closer to the C(2) hydrogen of the imidazolium cation and interacting more specifically as compared to BF(4-).     

A Bloembergen–Purcell–Pound <Superscript>13</Superscript>C NMR relaxation study of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate

The molecular structure and rotational motion of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6]) were studied over a wide temperature range using the Bloembergen–Purcell–Pound ¹³C NMR spin–lattice relaxation method and NOE factors. Examination of the spin–lattice relaxation times (T ₁) and the rates (R ₁=1/T ₁) of the 1-butyl-3-methylimidazolium cation reveals the relative motions of each carbon in the imidazolium cation. The rotational characteristics of the [BMIM] cation are supported by ab-initio molecular structures of [BMIM][PF6] using density functional theory (DFT) and Hartree–Fock (HF) methods. The ab-initio gas phase structures of [BMIM][PF6] indicate that the 1-butyl-3-methylimidazolium C2 hydrogen, the ring methyl group, and the butyl side-chain hydrogen atoms form hydrogen bonds with the hexafluorophosphate anion.