Shape memory effect in nanosized Ti<Subscript>2</Subscript>NiCu alloy-based composites

The shape memory effect (SME) in alloys with a thermoelastic martensite transition opens unique opportunities for the creation of miniature mechanical devices. The SME has been studied in layered composite microstructures consisting of a Ti₂NiCu alloy and platinum. It occurs upon a decrease in the active layer thickness at least to 80 nm. Some physical and technological restrictions on the minimum size of a material with SME are discussed.     

Studying the elastocaloric effect in a fast-quenched Ti<Subscript>2</Subscript>NiCu ribbon with the shape memory effect

The elastocaloric effect (ECE) in fast-quenched Ti₂NiCu ribbon under the periodic action of tensile force is studied experimentally. The ECE is measured as a function of relative elongation and the frequency of cycles in the range of 0.2 to 4 Hz. The maximum measured ECE in the alloy is 9.4 K under a mechanical load of 300 MPa at a relative deformation of 1%, frequencies of 0.2 to 0.5 Hz, and a temperature of 67°C. The specific power of the ribbon is estimated; it reaches its maximum at a frequency of f = 4 Hz, corresponding to W = 10 W g^?1. The possible practical use of Ti₂NiCu alloy for elastocaloric cooling is discussed.     

Structure and functional properties of rapidly quenched ribbons of Ti<Subscript>2</Subscript>NiCu alloy with different fractions of the crystalline phase

The controllable annealing of amorphous Ti₂NiCu ribbons by a pulsed electric current was developed, and samples with different fractions of crystalline phase were obtained. The samples’ structure was studied using high-resolution electron microscopy. Annealing conditions allowing us to obtain an amorphous nanocrystalline structure with grain sizes of less than 10 nm were determined. Conditions for obtaining samples with the two-wave shape memory effect were found. A prototype micromanipulator was designed and successfully tested.     

Superconductivity in Ti-doped iron-arsenide compound Sr<Subscript>4</Subscript>Cr<Subscript>0.8</Subscript>Ti<Subscript>1.2</Subscript>O<Subscript>6</Subscript>Fe<Subscript>2</Subscript>As<Subscript>2</Subscript>

Superconductivity was achieved in Ti-doped iron-arsenide compound Sr₄Cr_0.8Ti_1.2O₆Fe₂As₂ (abbreviated as Cr-FeAs-42622). The X-ray diffraction measurement shows that this material has a layered structure with the space group of P4/nmm, and with the lattice constants a = b = 3.9003 Å and c = 15.8376 Å. Clear diamagnetic signals in ac susceptibility data and zero-resistance in resistivity data were detected at about 6 K, confirming the occurrence of bulk superconductivity. Meanwhile we observed a superconducting transition in the resistive data with the onset transition temperature at 29.2 K, which may be induced by the nonuniform distribution of the Cr/Ti content in the FeAs-42622 phase.     

Preparation and electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Ti<Subscript>4</Subscript>O<Subscript>7</Subscript> composite for lithium-ion batteries

In order to improve the rate capability of Li₄Ti₅O₁₂, Ti₄O₇ powder was successfully fabricated by improved hydrogen reduction method, then a dual-phase composite Li₄Ti₅O₁₂/Ti₄O₇ has been synthesized as anode material for lithium-ion batteries. It is found that the Li₄Ti₅O₁₂/Ti₄O₇ composite shows higher reversible capacity and better rate capability compared to Li₄Ti₅O₁₂. According to the charge-discharge tests, the Li₄Ti₅O₁₂/Ti₄O₇ composite exhibits excellent rate capability of 172.3 mAh g^?1 at 0.2 C, which is close to the theoretical value of the spinel Li₄Ti₅O₁₂. More impressively, the reversible capacity of Li₄Ti₅O₁₂/Ti₄O₇ composite is 103.1 mAh g^?1 at the current density of 20 C after 100th cycles, and it maintains 84.8% of the initial discharge capacity, whereas that of the bare spinel Li₄Ti₅O₁₂ is only 22.3 mAh g^?1 with a capacity retention of 31.1%. The results indicate that Li₄Ti₅O₁₂/Ti₄O₇ composite could be a promising anode material with relative high capacity and good rate capability for lithium-ion batteries.     

Ferroelectric and dielectric properties of SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> thin films grown on Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> film layer

Ferroelectric and dielectric properties of bilayered ferroelectric thin films, SrBi₄Ti₄O₁₅ grown on Bi₄Ti₃O₁₂, were investigated. The thin films were annealed at 700°C under oxygen atmosphere. The bilayered thin films were prepared on a Pt(111)/Ti/SiO₂/Si substrate by a chemical solution deposition method. The dielectric constant and dielectric loss of the bilayered thin films were 645 and 0.09, respectively, at 100 kHz. The value of remnant polarization (2P _r) measured from the ferroelectric thin film capacitors was 60.5 μC/cm² at electric field of 200 kV/cm. The remnant polarization was reduced by 22% of the initial value after 10¹⁰ switching cycles. The results showed that the ferroelectric and dielectric properties of the SrBi₄Ti₄O₁₅ on Bi₄Ti₃O₁₂ ferroelectric thin films were better than those of the SrBi₄Ti₄O₁₅ grown on a Pt-coated Si substrate suggesting that the improved properties may be due to the different nucleation and growth kinetics of SrBi₄Ti₄O₁₅ on the c-axis-oriented Bi₄Ti₃O₁₂ layer or on the Pt-coated Si substrate.     

Origination and Propagation of the Temperature Front on Crystallization of Ti<Subscript>50</Subscript>Cu<Subscript>50</Subscript> Amorphous Alloy

A kinetic model and mechanism of the origination and propagation of a temperature front in the Ti₅₀Cu₅₀ alloy experiencing an amorphous-to-crystalline transition initiated by a volume thermal source are proposed. The physical reasons and conditions for this phenomenon are considered. The model qualitatively and quantitatively agrees with the experimental data for the propagation of the temperature front.     

Influence of K<Subscript>2</Subscript>Ti<Subscript>6</Subscript>O<Subscript>13</Subscript> on dielectric and barrier properties of polymer

Polymer composite comprising polyvinylidene fluoride (PVDF) and potassium hexatitante (K₂Ti₆O₁₃) was synthesized by solution casting. The effect of K₂Ti₆O₁₃ on surface, thermal, and electrical properties of polymer composite were investigated. The addition of K₂Ti₆O₁₃ with polymer leads to thermal degradation and transition of polymer composite from semi-crystalline to amorphous phase. The optimum results of contact angle for different loading wt% of K₂Ti₆O₁₃ were directly correlated with the surface morphology. Our experimental results confirmed the incorporation of K₂Ti₆O₁₃ in polymer by SEM micrographs. The evaluated dielectric properties (ε' = 424; tan δ = 2.14 at 130 °C and 100 Hz frequency for 20 wt% loading of K₂Ti₆O₁₃) for polymer composite are higher in compared to pure polymer. The enhancement in dielectric constant and changing the surface properties of polymer composite can be used for the development of electrochemical storage device applications.     

Effect of sintering conditions on the properties of sol-gel-derived Li<Subscript>1.3</Subscript>Al<Subscript>0.3</Subscript>Ti<Subscript>1.7</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

Solid electrolyte Li_1.3Al_0.3Ti_1.7(PO₄)₃ was prepared by sol-gel method under different sintering conditions. The structural identification, surface morphology, electrochemical window, ionic conductivity, and activation energy of the Li_1.3Al_0.3Ti_1.7(PO₄)₃ sintered pellets were investigated by X-ray diffraction, scanning electron microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. It is found that the sintering temperature and time have considerable effect on the properties of the Li_1.3Al_0.3Ti_1.7(PO₄)₃ sintered pellets. The Li_1.3Al_0.3Ti_1.7(PO₄)₃ pellet sintered at 900 °C for 2 h is denser than the pellets sintered at other conditions. Different sintering conditions result in the sintered pellet with different porosity. However, the sintering conditions have little effect on the electrochemical window of Li_1.3Al_0.3Ti_1.7(PO₄)₃. Among the Li_1.3Al_0.3Ti_1.7(PO₄)₃ pellets sintered at various conditions, the pellet sintered at 900 °C for 2 h shows the highest ionic conductivity of 3.46 × 10⁻⁴ S cm⁻¹ and the lowest activation energy of 0.2821 eV.     

Structural Aspects of Deformational Amorphization of Ti<Subscript>50</Subscript>Ni<Subscript>25</Subscript>Cu<Subscript>25</Subscript> Crystalline Alloy under High Pressure Torsion

The evolution of the structure of the Ti50Ni25Cu25 crystalline alloy during high-pressure torsion at room temperature has been studied. The torsional moment variation curve as a function of the strain value was fixed in situ, which allowed directly observing the transition of the material from the crystalline state to the amorphous state during the HPT. It was found that the amorphization of the material in the course of the HPT begins on the grain boundaries and fragments of the crystalline phase. Amorphized boundaries form a “grain-boundary carcass” in the cells of which the high-defect nanocrystalline phase is formed. Growth of deformation leads to broadening of the “grain-boundary carcass,” loss of stability of the crystalline phase, and, as a consequence, to the phase transition “crystal → amorphous” state.     

Effect of thermal strain on structure and polarization fatigue of CSD-derived PbZr<Subscript>0.53</Subscript>Ti<Subscript>0.47</Subscript>O<Subscript>3</Subscript>/LaNiO<Subscript>3</Subscript> hetero-structures

PbZr_0.53Ti_0.47O₃/LaNiO₃ (PZT/LNO) hetero-structures have been successfully deposited on MgO, SrTiO₃, Al₂O₃ and Si substrate by chemical solution routes, respectively. The X-ray diffraction measurements show that out-of-plane lattice parameters of PZT increase as increase of thermal expansion coefficient of substrate. Polarization fatigues of Pt/PZT/LNO capacitors are strongly affected by the thermal strain caused by difference of thermal expansion coefficient between PZT and substrate materials. High fatigue resistance of Pt/PZT/LNO can be obtained by using substrate with similar thermal expansion coefficient as PZT. PACS 77.84.Dy; 78.20.Ci; 81.20.Fw     

Effect of Ba-substitution on the structure and properties of Pb<Subscript>0.8</Subscript>Ba<Subscript>0.2</Subscript>[(In<Subscript>1/2</Subscript>Nb<Subscript>1/2</Subscript>)<Subscript>1-x</Subscript>Ti<Subscript>x</Subscript>]O<Subscript>3</Subscript> ceramics

Ferroelectric ceramics with formula Pb_0.8Ba_0.2[(In_1/2Nb_1/2)_1-xTi_x]O₃ (PBINT) (x=0.0,0.1,0.2,0.3,0.4 and 0.5) were prepared via a two-step solid state reaction method. It was found that ceramics with compositions in the range of x=0.0∼0.3 showed a pseudo-cubic structure, whereas the ceramic with x=0.5 displayed a tetragonal structure. All compositions showed significant frequency dispersion in their dielectric properties. The remanent polarization P_r as well as the coercive field E_c, measured at room temperature, increases with the Ti content. The experimental results obtained in this system are summarized into a phase diagram, with the morphotropic phase boundary (MPB) located at x=0.4. Compared with the Pb[(In_1/2Nb_1/2)_1-xTi_x]O₃ solid solution system, incorporating Ba in the A-site leads to a significant decrease in the dielectric maximum temperature T_max, a suppression of the dielectric relaxation parameter γ, and a shift of the MPB composition to a higher Ti content. PACS 77.84.Dy; 77.80.Bh; 77.22.Ch     

Manufacturing of Sputtering Composite Targets Containing Phases of Co<Subscript>2</Subscript>FeSi or Co<Subscript>2</Subscript>MnSi Heusler Alloy

The paper presents a method for manufacturing mechanically strong sputtering composite targets containing the phase of the Co₂FeSi or Co₂MnSi Heusler alloy of the stoichiometric composition, which can be used for fabrication of spin electronic devices by high-frequency magnetron deposition and pulsed laser deposition of thin films.     

Effect of calcination conditions on lithium conductivity in Li<Subscript>1.3</Subscript>Ti<Subscript>1.7</Subscript>Al<Subscript>0.3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> prepared by sol-gel route

In order to study the influence of powder calcination temperature on lithium ion conductivity, synthesized Li_1.3Ti_1.7Al_0.3(PO₄)₃ (LATP) was calcined at temperatures between 750 and 900 °C. The shape and size of the particles were characterized employing scanning electron microscopy (SEM), and specific surface area of the obtained powder was measured. The crystallinity grade of different heat-treated powders was calculated from XRD spectra. Posteriorly, all powders were sintered at 1100 °C employing field-assisted sintering (SPS), and the electrical properties were correlated to the calcination conditions. The highest ionic conductivity was observed for samples made out of powders calcined at 900 °C.     

Dielectric and polar order behaviors of BaTiO<Subscript>3</Subscript>-Bi(Mg<Subscript>1/2</Subscript>Ti<Subscript>1/2</Subscript>)O<Subscript>3</Subscript> ceramics

New perovskite solid solution ceramics of (1−x)BaTiO₃-xBi(Mg_1/2Ti_1/2)O₃ ((1−x)BT-xBMT, x≤0.09) were synthesized by the solid-state reaction technique. X-ray diffraction studies have revealed a stable single perovskite structure for all samples. Dielectric measurements were carried out at different frequencies and temperatures. The polarization evolutions with temperatures were measured to investigate the ferroelectric properties. All the compositions show features of ferroelectrics with diffuse phase transition, though the temperature T _m of their dielectric constant maximum ε _m is frequency dependent. The dielectric constant peak ε(T) of (1−x)BT-xBMT ceramics become broad with increasing BMT content. During the temperature range of ε(T) peak summit, (1−x)BT-xBMT ceramics present quasi-linear dielectric phenomenon under high electric field with very high dielectric constant.     

Structural disordering in Cr-doped Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> spinels

The processes of lithium redistribution in the structure of cubic Li₄Ti₅O₁₂ spinel, caused by both chromium doping and thermal activation, have been investigated by nuclear magnetic resonance. It is shown that Li ions migrate from tetra- to octahedral crystallographic positions with an increase in temperature. This process becomes more pronounced at temperatures above 400 K. In contrast, the fraction of tetrahedrally coordinated Li increases as a result of doping with chromium.     

Synthesis and electrochemical performance of spherical LiNi<Subscript>0.8</Subscript>Co<Subscript>0.15</Subscript>Ti<Subscript>0.05</Subscript>O<Subscript>2</Subscript> cathode materials with high tap density

A series of spherical LiNi_0.8Co_0.15Ti_0.05O₂ cathode materials were synthesized through co-oxidation-controlled crystallization method followed by solid-state reaction at different calcination temperatures under oxygen flowing. The crystal structure and particles morphology of the as-prepared powders were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. All samples correspond to the layered α-NaFeO₂ structure with R-3m space group. The LiNi_0.8Co_0.15Ti_0.05O₂ prepared at 800 °C presents a better hexagonal ordering structure and better spherical particles and possesses a high tap density of 3.22 g cm^?3. Meanwhile, the NCT-2 sample exhibits an advanced electrochemical performance with an initial discharge capacity of 174.2 mAh g^?1 and capacity retention of 86.7 % after 30 cycles at 0.2 C.     

Phase transition in Bi<Subscript>8</Subscript>Fe<Subscript>6</Subscript>Ti<Subscript>3</Subscript>O<Subscript>27</Subscript> multiferroic ceramics

The polycrystalline Bi₈Fe₆Ti₃O₂₇ compound was prepared by a high-temperature solid-state reaction technique. Preliminary structural analysis by X-ray diffraction (XRD) confirms the formation of a single-phase compound in an orthorhombic crystal system at room temperature. The elemental content of the compound was analyzed by EDAX microanalysis. Microstructural analysis by scanning electron microscopy (SEM) shows that the compound has well defined grains, which are distributed uniformly throughout the surface of the pellet sample. Detailed studies of temperature-dependent dielectric response at various frequencies show dielectric anomalies at 380, 389 and 403°C for 10 kHz, 100 kHz, and 1 MHz respectively. The hysteresis loop observed by applying an electric field of 12 kV/cm on the poled sample with smaller remanent polarization supports the existence of ferroelectricity in this material. The value of d₃₃ of the compound was found to be 19 pC/N.