Influence of polycaprolactone-triol addition on thermal stability of soy protein isolate based films

The influence of polycaprolatone-triol (PCL-T) on the thermal degradation properties of soy protein isolate (SPI)-based films was studied by thermogravimetry and infrared spectroscopy under nitrogen atmosphere. The results showed that in the absence of PCL-T the thermal degradation began between 292 °C (pure SPI films) and ca. 264 °C (SPI/SDS films with more than 20% of SDS), and these values decreased further to the range 250-255 °C for SPI/SDS/PCL-T films. At the same time, the temperature of maximum degradation rate (T_max) decreased from 331 °C (pure SPI film) to ca. 280 °C for SPI/SDS/PCL-T films with 39% PCL-T content. This behavior was also confirmed by the activation energy (E) values associated with the thermal degradation process. Apparently, the low thermal stability of PCL-T as compared to other film constituents, along with its plasticizer characteristics, is responsible for the decreased stability of SPI/SDS/PCL-T films. The FTIR spectra of gas products evolved during the thermal degradation indicated the formation of OH, CO₂, NH₃ and other saturated compounds, suggesting that the reaction mechanism involved simultaneous scission of the C(O)-O polyester bonds and C-N, C(O)-NH, C(O)-NH₂ and -NH₂ bonds of the protein.     

NMR Studies and electrophilic properties of triphenylphosphine-trifluoromethanesulfonic anhydride; a remarkable dehydrating reagent system for the conversion of aldoximes into nitriles

NMR Studies on the reaction of triphenylphosphine with various amounts of triflic anhydride at 0 °C is described. The reagent structure resulting from mixing 1.3 equiv of Ph₃P with Tf₂O (1.0 mmol) has been established as an equilibrium mixture consisting mainly of triphenyl(trifluoromethylsulfonyloxy)phosphonium trifluoromethanesulfinate and the corresponding bis(triphenyl)oxodiphosphonium trifluoromethanesulfinate dimer. The electrophilic properties of the system have been exploited in the development of a mild method for converting aldoximes into nitriles. The dehydration occurs at 0 °C under very mild conditions by initial activation of the oxime oxygen, followed by treatment with a base and subsequent elimination of triphenylphosphine oxide. The substrate scope and functional group tolerance of this useful method are explored.     

Preparation and performances of nanosized Ta2O5 powder photocatalyst

Nanosized-Ta₂O₅ powder photocatalyst was successfully synthesized by using sol-gel method via TaCl₅ butanol solution as a precursor. Ta₂O₅ species can be formed under 500 °C via the decomposition of the precursor. The crystalline phase of Ta₂O₅ powder photocatalyst can be obtained after being calcined above 600 °C for 4 h. The crystal size and particle size of Ta₂O₅ powder photocatalyst was about 50 nm. A good photocatalytic performance for the degradation of gaseous formaldehyde was obtained for the nanosized-Ta₂O₅ powder. The Ta₂O₅ powder formed at 700 °C for 4 h and at 650 °C for 12 h showed the best performance. The calcination temperature and time play an important role in the crystallization and photocatalytical performance of nanosized-Ta₂O₅ powder.     

Comparative study on hydrolytic degradation and monomer recovery of poly(l-lactic acid) in the solid and in the melt

The hydrolytic degradation of poly(l-lactide) (PLLA) and the formation of its monomer in the solid and in the melt were investigated at 120-150 °C (in the solid), at 160 °C (in the solid up to 40 min and in the melt exceeding 40 min), and at 170-190 °C (in the melt). Such state difference caused the difference in the degradation behavior of PLLA and the behavior of lactic acid formation, although the degradation of PLLA proceeds via a bulk erosion mechanism, regardless of its state. The crystalline residues were formed at the degradation temperatures below 140 °C, but not at the degradation temperatures above 160 °C. The lactic acid yield exceeding 95% can be successfully attained for all the temperatures of 120-190 °C. The activation energy for hydrolytic degradation values of PLLA were 69.6 and 49.6 kJ mol⁻¹ for the temperature ranges of 120-160 °C (in the solid) and 170-250 °C (in the melt), respectively, and are compared with the reported values.     

Electron-beam irradiation on poly(propylene carbonate) in the presence of polyfunctional monomers

Poly(propylene carbonate) (PPC) showed predominantly degradation under electron-beam irradiation, accompanied by deterioration of its mechanical performance due to sharp decrease of the molecular weight. Crosslinked PPC was prepared by addition of polyfunctional monomer (PFM) to enhance the mechanical performance of PPC. When 8 wt% of PFM like triallyl isocyanurate (TAIC) was added, crosslinked PPC with a gel fraction of 60.7% was prepared at 50 kGy irradiation dose, which showed a tensile strength at 20 °C of 45.5 MPa, whereas it was only 38.5 MPa for pure PPC. The onset degradation temperature (T_i) and glass transition temperature (T_g) of this crosslinked PPC was 246 °C and 45 °C, respectively, a significant increase related to pure PPC of 211 °C and 36 °C. Therefore, thermal and mechanical performances of PPC could be improved via electron-beam irradiation in the presence of suitable PFM.     

Synthesis and characterization of some novel aromatic polyimides

Three new diamines 1,2-di(p-aminophenyloxy)ethylene, 2-(4-aminophenoxy)methyl-5-aminobenzimidazole and 4,4-(aminopheyloxy) phenyl-4-aminobenzamide were synthesized and polymerized with 3,3′,4,4′-benzophenone tetracarboxylic acid dianhydride (BP), 4,4′-(hexafluoroisopropyledene)diphthalic anhydride (HF) and 3,4,9,10-perylene tetracarboxylic acid dianhydride (PD) either by one step solution polymerization reaction or by two step procedure. The later includes ring opening poly-addition to give poly(amic acid), followed by cyclodehydration to polyimides with the inherent viscosities 0.62-0.97 dl/g. Majority of polymers are found to be soluble in most of the organic solvents such as DMSO, DMF, DMAc, m-cresol even at room temperature and few becomes soluble on heating. The degradation temperature of the resultant polymers falls in the ranges from 240 °C to 550 °C in nitrogen (with only 10% weight loss). Specific heat capacity at 300 °C ranges from 1.1899 to 5.2541 J g⁻¹ k⁻¹. The maximum degradation temperature ranges from 250 to 620 °C. T_g values of the polyimides ranged from 168 to 254 °C.     

Formation of γ-Fe2O3 nanoparticles and vacancy ordering: An in situ X-ray powder diffraction study

The formation of maghemite, γ-Fe₂O₃ nanoparticles has been studied by in situ X-ray powder diffraction. The maghemite was formed by thermal decomposition of an amorphous precursor compound made by reacting lauric acid, CH₃(CH₂)₁₀COOH with Fe(NO₃)₃·9H₂O. It has been shown that cubic γ-Fe₂O₃ was formed directly from the amorphous precursor and that vacancy ordering starts about 45 min later at 305 °C resulting in a tripled unit cell along the c-axis. The kinetics of grain growth was found to obey a power law with growth exponents n equal to 0.136(6) and 0.103(5) at 305 and 340 °C, respectively. Particles with average sizes of 12 and 13 nm were obtained in 86 and 76 min at 305 and 340 °C, respectively. The structure of cubic and vacancy ordered phases of γ-Fe₂O₃ was studied at 305 °C by Rietveld refinements.     

Reducing the formation of six-membered ring ester during thermal degradation of biodegradable PHBV to enhance its thermal stability

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) has attracted the attention of academia and industry because of its biodegradability, biocompatibility, thermoplasticity and plastic-like properties. However, PHBV is unstable above 160 °C during melt processing at a temperature above the melting temperature, which restricts practical applications as a commodity material. It is widely believed that thermal degradation of PHBV occurs almost exclusively via a random chain scission mechanism involving a six-membered ring transition state. Here, 2,2′-bis(2-oxazoline) (BOX) was selected to modify PHBV to control the formation of six-membered ring ester during thermal degradation. The resulting hydroxyl-terminated PHBVs (HT-PHBVs) had improved thermal stability due to a decrease in the negative inductive effect of the neighboring group of methylene groups at the β-position to the ester oxygen, and a decrease in the electron-denoting effect of substituent group of carbon atoms at α-position to the ester oxygen. The optimal reaction temperature and time were determined to be 95 °C and 6 h, respectively. Compared with those of original PHBV, the temperature determined at 5% weight loss (T_5%), the initial decomposition temperature (T₀), the maximum decomposition temperature (T_max), the complete decomposition temperature (T_f) of HT-PHBV prepared under the optimal conditions increased by 31, 24, 19 and 19.1 °C, respectively.     

Thermal stability of silver sulfathiazole-epoxy resin network

The aim of this study is to evaluate the thermal stability and thermal degradation behavior of an epoxy network based on bisphenol A modified with silver sulfathiazole and crosslinked with ethylenediamine. The sample was studied by thermogravimetric analysis coupled with differential scanning calorimetry over a range of temperature between 30 and 600 °C in N₂ atmosphere and using heating rates of 5, 10, 15 and 20 °C min⁻¹. The kinetic parameters of thermal degradation process were calculated. Fourier transforms infrared spectroscopy and mass spectroscopy coupled to thermogravimetry was used to identify the volatile products resulting from the degradation of the network. The study showed that the sample is stable up to temperatures exceeding 290 °C. The major degradation volatile products identified were: ammonia, water, carbon dioxide and compounds with aromatic structure such as bisphenol A and its degradation products.     

Catalytic activity of a half-sandwich Ru(II)-N-heterocyclic carbene complex in the oligomerization of alkynes

The ruthenium(II)-N-heterocyclic carbene complex, [RuCl₂(1-butyl-3-methylimidazol-2-ylidene)(p-cymene)] selectively catalyzes oligomerization of phenylacetylene (PA) and its derivatives to linear oligomers, containing positively charged imidazolium end-group and uncharged ones. The charged oligomer chain consists of maximum 9-11 PA monomer units after 36 h reaction at 80 °C whereas mainly pentamers are formed as other products. The H₂ atmosphere retards oligomerization of PA and hydrogenation to vinylbenzene and ethylbenzene is observed instead.     

Solution combustion synthesis of calcium zirconate, CaZrO3, powders

Single-phase CaZrO₃ powder was prepared by heating at 300 °C an aqueous solution of Ca(NO₃)₂, ZrO(NO₃)₂ and β-C₃H₇NO₂ (molar ratio=3:3:4). TG-DTA analysis indicated that an intense exothermic reaction occurred at 255 °C, which lead to the formation of a voluminous white powder. No additional annealing was required, as pure crystalline CaZrO₃ resulted directly from the combustion reaction. Although no advanced milling was performed, the specific surface area of the powder was 21.5 m²/g. The average crystallite size of CaZrO₃ was 23.9 nm. After sintering in air at 1400 °C for 2 h, the pellets - shaped by uniaxial pressing at 200 MPa - reached 95% of the theoretical density, had no open pores and were slightly translucent.     

A thermal degradation mechanism of polyvinyl alcohol/silica nanocomposites

The thermal degradation mechanism of a novel polyvinyl alcohol/silica (PVA/SiO₂) nanocomposite prepared with self-assembly and solution-compounding techniques is presented. Due to the presence of SiO₂ nanoparticles, the thermal degradation of the nanocomposite, compared to that of pure PVA, occurs at higher temperatures, requires more reaction activation energy (E), and possesses higher reaction order (n). The PVA/SiO₂ nanocomposite, similar to the pure PVA, thermally degrades as a two-step-degradation in the temperature ranges of 300-450 °C and 450-550 °C, respectively. However, the introduction of SiO₂ nanoparticles leads to a remarkable change in the degradation mechanism. The degradation products identified by Fourier transform infrared/thermogravimetric analysis (FTIR/TGA) and pyrolysis-gas chromatography/mass spectrometric analysis (Py-GC/MS) suggests that the first degradation step of the nanocomposite mainly involves the elimination reactions of H₂O and residual acetate groups as well as quite a few chain-scission reactions. The second degradation step is dominated by chain-scission reactions and cyclization reactions, and continual elimination of residual acetate groups is also found in this step.     

Phenylethynylnaphthalic endcapped imide oligomers with reduced cure temperatures

A series of 4-(2-phenylethynyl)-1,8-naphthalic anhydride (PENA) endcapped imide oligomers with different chemical backbones and calculated number average molecular weights (Calc’d M_n) were successfully synthesized and characterized. The PENA-endcapped imide oligomers were mixtures of mono- and double-endcapped imide oligomers with polymerization degree (P_n) of 1-5 and number average molecular weights (M_n) of 2515-3851 g/mol. determined by GPC. Study on effect of chemical structures on the curing behaviors of two model compounds: PENA-m based on PENA and PEPA-m derived from 4-phenylethynylphthalic anhydride (PEPA) revealed that PENA-m showed the cure temperature of 50 °C lower than PEPA-m and the activity energy of thermal curing reaction for PENA-m was also lower than that of PEPA-m. The PENA-endcapped imide oligomers could be melt at temperatures of >250 °C with the minimum melt viscosity of 1.2-230 Pa s at 275-301 °C and the widen melt processing windows, along with 10-40 °C lower cure temperature than the PEPA-endcapped analogue.The PENA-endcapped imide oligomers could be thermally cured at 350 °C/1 h to afford the thermally cured polyimides with good combined thermal and mechanical properties including T_g of 344-397 °C (DMA), T_d of 443-513 °C, tensile strength of as high as 54.7 MPa, flexural strength of as high as 126.1 MPa and modulus of as high as 2.3 GPa, respectively.     

Microstructure and electrical-optical properties of cesium tungsten oxides synthesized by solvothermal reaction followed by ammonia annealing

Cesium tungsten oxides (Cs_xWO₃) were synthesized by solvothermal reactions using ethanol and 57.1 vol% ethanol aqueous solution at 200 °C for 12 h, and the effects of post annealing in ammonia atmosphere on the microstructure and electrical-optical properties were investigated. Agglomerated particles consisting of disk-like nanoparticles and nanorods of Cs_xWO₃ were formed in the pure ethanol and ethanol aqueous solutions, respectively. The samples retained the original morphology and crystallinity after annealing in ammonia atmosphere up to 500 °C, while a small amount of nitrogen ion were incorporated in the lattice. The as-prepared Cs_xWO₃ sample showed excellent near infrared (NIR) light shielding ability as well as high transparency in the visible light region. The electrical resistivity of the pressed pellets of the powders prepared in pure ethanol and 57.1 vol% ethanol aqueous solution greatly decreased after ammonia annealing at 500 °C, i.e., from 734 to 31.5 and 231 to 3.58 Ω cm, respectively.     

Preparation and thermal properties of diglycidylether sulfone epoxy

A diglycidylether sulfone monomer (sulfone type epoxy monomer, SEP) was prepared from bis(4-hydroxyphenyl) sulfone (SDOL) and epichlorohydrin without any NaOH or KOH as basic catalyst. FT-IR, ¹H NMR, ¹³C NMR and mass spectroscopic instruments were utilized to determine the structure of the SEP monomer. The cured SEP epoxy material exhibited not only a higher T_g (163.81 °C) but also a higher T_g than pristine DGEBA (from 111.25 °C to 139.17 °C) when the SEP monomer moiety had been introduced into the DGEBA system. The thermal stability of cured epoxy herein was investigated by thermogravimetric analysis (TGA). The results demonstrated that the sulfone group of the cured SEP material decomposed at lower temperatures and formed thermally stable sulfate compounds, improving char yield and enhancing resistance against thermal oxidation. Additionally, the IPDT and char yield of the cured SEP epoxy (IPDT = 1455.75, char yield = 39.67%) exceeded those of conventional DGEBA epoxy (IPDT = 667.27, char yield = 16.25%).     

Optimum conditions for intercalation of lacunary tungstophosphate(V) anions into layered Ni(II)-Zn(II) hydroxyacetate

Acetate containing nickel-zinc hydroxysalts (LHS-Ni-Zn) have been synthesized by coprecipitation and hydrothermal treatment. The acetate anions were exchanged with PW₁₂O₄₀³⁻ anions, and optimum conditions to attain the maximum level of W in the compound have been identified. The W intercalated compound was characterized by powder X-ray diffraction, FT-IR spectroscopy, thermogravimetric and differential thermal analyses, scanning electron microscopy and transmission electron microscopy.The exchange of LHS-Ni-Zn with PW₁₂O₄₀³⁻ at pH=3 for 72 h leads to a solid with a basal spacing of 9.62 Å and a W content (weight) of 37%. The hydrothermal treatment at 90 °C for 24 h increases this value to 48% with a W/Zn molar ratio of 1.38, which corresponds to a layered compound with lacunary tungstophosphate anions in the interlayer space. The intercalated solid is stable up to 250 °C, the layer structure collapses on dehydroxylation and amorphous compounds were identified at 500 °C. Two crystalline phases, NiO (rock salt) and a solid solution (Zn_1−xNi_x)WO₄, were identified by powder X-ray diffraction at high temperature (ca. 1000 °C).     

The mechanism of HF formation in LiPF6 based organic carbonate electrolytes

Spectroscopic ellipsometry was used to study the time-dependent formation of HF upon the thermal degradation of LiPF₆ at 50 °C in a lithium ion battery electrolyte containing ethylene carbonate and diethyl carbonate. The generated HF was monitored by following the etching rate of a 300 nm thick SiO₂ layer, grown on both sides of a silicon wafer substrate, as a function of the immersion time in the electrolyte at 50 °C. It was found that the formation of HF starts after 70 h of exposure time and occurs following several different phases. The amount of generated HF was calculated using an empirical formula correlating the etching rate to the temperature. Combining the results of the HF formation with literature data, a simplified mechanism for the formation of the HF involving LiPF₆ degradation, and a simplified catalytical reaction pathway of the formed HF and silicon dioxide are proposed to describe the kinetics of HF formation.     

Synthesis and characterization of novel polyamides from new aromatic phosphonate diamine monomer

New aliphatic-aromatic and fully aromatic phosphonate polyamides were prepared by polycondensation reaction of our synthesized aromatic diamine: tetraethyl[(2,5-diamino-3,6-dimethylbenzene-1,4-diyl)dimethanediyl]bis(phosphonate) with the specific di-acylchloride (adipoyl chloride, isophthaloyl chloride and terephthaloyl chloride). The chemical structure of all samples were characterized by (¹H and ³¹P) NMR, MALDI-TOF MS, FT-IR tools, whereas their thermal properties were determined by DSC and TGA techniques. The phosponate polyadipamide (referred as PAP) is a semi-crystalline sample with a melting temperature at about 261 °C and glass transition (T_g) of 71 °C. All polymers show two thermal degradation steps in the temperature range 270-550 °C. Each polymer, independently its structure, shows the first maximum rate of thermal decomposition temperature (PDT) around 300-310 °C, which may be due to thermal degradation of phoshonate groups. MALDI-TOF spectra, beside the linear oligomers terminated with the specific groups expected in accord to the synthesis procedure, reveals the presence of cyclic oligomers in the polyadipamide and polyisophthalamide samples.     

Low-temperature heat capacity and thermodynamic properties of crystalline carboxin (C12H13NO2S)

Carboxin was synthesized and its heat capacities were measured with an automated adiabatic calorimeter over the temperature range from 79 to 380 K. The melting point, molar enthalpy (Δ_fusH_m) and entropy (Δ_fusS_m) of fusion of this compound were determined to be 365.29±0.06 K, 28.193±0.09 kJ mol⁻¹ and 77.180±0.02 J mol⁻¹ K⁻¹, respectively. The purity of the compound was determined to be 99.55 mol% by using the fractional melting technique. The thermodynamic functions relative to the reference temperature (298.15 K) were calculated based on the heat capacity measurements in the temperature range between 80 and 360 K. The thermal stability of the compound was further investigated by differential scanning calorimetry (DSC) and thermogravimetric (TG) analysis. The DSC curve indicates that the sample starts to decompose at ca. 290 °C with the peak temperature at 292.7 °C. The TG-DTG results demonstrate the maximum mass loss rate occurs at 293 °C corresponding to the maximum decomposition rate.     

Gas- and solid/liquid-phase reactions during pyrolysis of softwood and hardwood lignins

Pyrolytic reactions of Japanese cedar (Cryptomeria japonica, a softwood) and Japanese beech (Fagus crenata, a hardwood) milled wood lignins (MWLs) were studied with thermogravimetry (TG) and by pyrolysis in a closed ampoule reactor (N₂/600 °C). The data were compared with those of guaiacol/syringol as simple lignin model aromatic nuclei. Several DTG peaks were observed around 300-350, 450, 590 and 650 °C. The first DTG peak temperature (326 °C) of beech was lower than that (353 °C) of cedar. This indicates that the volatile formation from cedar MWL is slightly delayed in heating at 600 °C. The gas-phase reactions via GC/MS-detectable low MW products were explainable with the temperature-dependent reactions observed for guaiacol/syringol in our previous paper. The methoxyl groups became reactive at ∼450 °C, giving O-CH₃ homolysis products (catechols/pyrogallols) and OCH₃ rearrangement products (cresols/xylenols). The former homolysis products were effectively converted into gaseous products (mainly CO) at >550-600 °C. However, the GC/MS-detectable tar yields, especially syringyl unit-characteristic products, were much lower than those from guaiacol/syringol. Thus, contributions of higher MW intermediates and solid/liquid-phase reactions are more important in lignin pyrolysis. From the results of stepwise pyrolysis of char + coke fractions at 450 and 600 °C, the methoxyl group-related reactions (450 °C) and intermediates gasification (600 °C) were suggested to occur also in the solid/liquid phase. This was consistent with the DTG peaks observed around these temperatures. These solid/liquid-phase reactions reduced the tar formation, especially catechols/pyrogallols and PAHs. Different features observed between these two MWLs are also focused.