Thermo-Raman spectroscopy in situ monitoring study of solid-state synthesis of NiO-Al2O3 nanoparticles and its characterization

Hyphenation of thermogravimetric analyzer (TGA) and thermo-Raman spectrophotometer for in situ monitoring of solid-state reaction in oxygen atmosphere forming NiO-Al₂O₃ catalyst nanoparticles is investigated. In situ thermo-Raman spectra in the range from 200 to 1400 cm⁻¹ were recorded at every degree interval from 25 to 800 °C. Thermo-Raman spectroscopic studies reveal that, although the onset of formation is around 600 °C, the bulk NiAl₂O₄ forms at temperatures above 800 °C. The X-ray diffraction (XRD) spectra and the scanning electron microscopy (SEM) images of the reaction mixtures were recorded at regular temperature intervals of 100 °C, in the temperature range from 400 to 1000 °C, which could provide information on structural and morphological evolution of NiO-Al₂O₃. Slow controlled heating of the sample enabled better control over morphology and particle size distribution (∼20-30 nm diameter). The observed results were supported by complementary characterizations using TGA, XRD, SEM, transmission electron microscopy, and energy dispersive X-ray analysis.     

Separation of aromatic hydrocarbons from alkanes using ammonium ionic liquid C2NTf2 at T = 298.15 K

(Liquid + liquid) equilibrium data are presented for four ternary systems of an alkane, or aromatic compound and ethyl(2-hydroxyethyl)dimethylammonium bis{(trifluomethyl)sulfonyl}imide (C₂NTf₂) at 298.15 K: [hexane + benzene + C₂NTf₂], [hexane + p-xylene + C₂NTf₂], and [hexane, or octane + m-xylene + C₂NTf₂]. The separation of aromatic hydrocarbons (benzene, or p-xylene, or m-xylene) from aliphatic hydrocarbons (hexane, or octane) is investigated by extraction with the ammonium ionic liquid. Selectivities and distribution ratios are discussed for these mixtures at constant temperature. The data were analysed and compared to those previously reported for other ionic liquids and especially for the system {hexane + benzene + [EMIM][NTf₂]}. The nonrandom two liquid NRTL model was successfully used to correlate the experimental tie-lines and to calculate the phase compositions of the ternary systems.     

Liquid–liquid equilibrium for binary and ternary systems containing di-isopropyl ether (DIPE) and an imidazolium-based ionic liquid at different temperatures

Liquid–liquid equilibrium (LLE) data were determined for two binary systems {di-isopropyl ether (DIPE) + 1-ethyl-3-methylimidazolium-ethylsulfate (EMISE)} and {DIPE + 1-butyl-3-methylimidazolium-tetrafluoroborate([Bmim][BF₄])}at temperatures between 293.15 K and 313.15 K. LLE data for six ternary systems {DIPE + water + EMISE} and {DIPE + water + [Bmim][BF₄]} at 293.15 K, 303.15 K, and 313.15 K were also reported. Experiments were carried out at atmospheric pressure using stirred and thermo-regulated cells. The experimental data were correlated with the well-known NRTL and UNIQUAC activity coefficient models. In addition, distribution coefficients and selectivities of the ionic liquids EMISE and [Bmim][BF₄] for water in the DIPE phase were measured.     

A simple one-pot procedure for the direct conversion of alcohols into azides using TsIm

A facile and efficient method for one-pot conversion of alcohols into azides using N-(p-toluenesulfonyl)imidazole (TsIm) is described. In this method, alcohols are refluxed with a mixture of NaN₃, TsIm and triethylamine in the presence of catalytic amounts of tetra-n-butylammonium iodide (TBAI) in DMF affording the corresponding alkyl azides in good yields. This methodology is highly efficient for various structurally diverse alcohols with selectivity for ROH: 1° > 2° > 3°.     

Synthesis and structural investigation of the compounds containing HF2 anions: Ca(HF2)2, Ba4F4(HF2)(PF6)3 and Pb2F2(HF2)(PF6)

Three new compounds Ca(HF₂)₂, Ba₄F₄(HF₂)(PF₆)₃ and Pb₂F₂(HF₂)(PF₆) were obtained in the system metal(II) fluoride and anhydrous HF (aHF) acidified with excessive PF₅. The obtained polymeric solids are slightly soluble in aHF and they crystallize out of their aHF solutions. Ca(HF₂)₂ was prepared by simply dissolving CaF₂ in a neutral aHF. It represents the second known compound with homoleptic HF environment of the central atom besides Ba(H₃F₄)₂. The compounds Ba₄F₄(HF₂)(PF₆)₃ and Pb₂F₂(HF₂)(PF₆) represent two additional examples of the formation of a polymeric zigzag ladder or ribbon composed of metal cation and fluoride anion (MF⁺)_n besides PbF(AsF₆), the first isolated compound with such zigzag ladder. The obtained new compounds were characterized by X-ray single crystal diffraction method and partly by Raman spectroscopy. Ba₄F₄(HF₂)(PF₆)₃ crystallizes in a triclinic space group P1¯ with a=4.5870(2) Å, b=8.8327(3) Å, c=11.2489(3) Å, α=67.758(9)°, β=84.722(12), γ=78.283(12)°, V=413.00(3) Å³ at 200 K, Z=1 and R=0.0588. Pb₂F₂(HF₂)(PF₆) at 200 K: space group P1¯, a=4.5722(19) Å, b=4.763(2) Å, c=8.818(4) Å, α=86.967(10)°, β=76.774(10)°, γ=83.230(12)°, V=185.55(14) ų, Z=1 and R=0.0937. Pb₂F₂(HF₂)(PF₆) at 293 K: space group P1¯, a=4.586(2) Å, b=4.781(3) Å, c=8.831(5) Å, α=87.106(13)°, β=76.830(13)°, γ=83.531(11)°, V=187.27(18) Å³, Z=1 and R=0.072. Ca(HF₂)₂ crystallizes in an orthorhombic Fddd space group with a=5.5709(6) Å, b=10.1111(9) Å, c=10.5945(10) Å, V=596.77(10) Å³ at 200 K, Z=8 and R=0.028.     

Synthesis and decarboxylation of N-acyl-α-triphenylphosphonio-α-amino acids: a new synthesis of α-(N-acylamino)alkyltriphenylphosphonium salts

4-Phosphoranylidene-5(4H)-oxazolones 1 undergo hydrolysis in THF in the presence of HBF₄ at room temperature to give N-acyl-α-triphenylphosphonioglycines 3 (R² = H) in very good yields. 4-Alkyl-4-triphenylphosphonio-5(4H)-oxazolones 2 react with water in CH₂Cl₂/THF solution without any acidic catalyst at 0-5 °C in a few days yielding N-acyl-α-triphenylphosphonio-α-amino acids 3 (R² = Me) or α-(N-acylamino)alkyltriphenylphosphonium salt 4 (R² = CH₂OMe). α-Triphenylphosphonio-α-amino acids 3, on heating up to 105-115 °C under reduced pressure (5 mmHg) or on treatment with diisopropylethylamine in CH₂Cl₂ at 20 °C undergo decarboxylation to give the corresponding α-(N-acylamino)alkyltriphenylphosphonium salts 4, usually in very good yields.     

Bio-oil production from Onopordum acanthium L. by slow pyrolysis

In this study, the usability of the plant thistle, Onopordum acanthium L., belonging to the family Asteraceae (Compositae), in liquid fuel production has been investigated. The experiments were performed in a fixed-bed Heinze pyrolysis reactor to investigate the effects of heating rate, pyrolysis temperature and sepiolite percentage on the pyrolysis product yields and chemical compositions. Experiments were carried out in a static atmosphere with a heating rate of 7 °C/min and 40 °C/min, pyrolysis temperature of 350, 400, 500, 550 and 700 °C and particle size of 0.6 < D_p < 0.85 mm. Catalyst experiments were conducted in a static atmosphere with a heating rate of 40 °C/min, pyrolysis temperature of 550 °C and particle size of 0.6 < D_p < 0.85 mm. Bio-oil yield increased from 18.5% to 27.3% with the presence of 10% of sepiolite catalyst at pyrolysis temperature of 550 °C, with a heating rate of 40 °C/min, and particle size of 0.6 < D_p < 0.85 mm. It means that the yield of bio-oil was increased at around 48.0% after the catalyst added. Chromatographic and spectroscopic studies on the bio-oil showed that the oil obtained from O. acanthium L. could be used as a renewable fuels and chemical feedstock.     

Crystal structures of syndiotactic poly(p-methylstyrene) clathrates with two guest molecules having very similar shape and volume

In the present paper we report on the clathrate structures of syndiotactic poly(p-methylstyrene) (s-PPMS) containing chlorobenzene (cell constants: a = 23.5 Å, b = 12.0 Å, c = 7.9 Å and γ = 112.4°; space group: P2₁/a) and toluene (cell constants: a = 19.5 Å, b = 13.5 Å, c = 7.9 Å and γ = 90°; space group: P2₁). Despite the extreme similarity between the shape and volume of these two molecules, they give rise to completely different clathrate structures, the first belonging to α class, the second belonging to β class. Moreover the clathrate form containing chlorobenzene represent the first case in which a α class clathrate form of s-PPMS contains two guest molecules in each cavity while the crystal structure here proposed for the s-PPMS/toluene clathrate represents a new example of chiral crystalline phase in which the polymer helices assume all the same chirality in the lattice. These results underline the fact that the choice of a particular structural organization in the process of clathrates’ formation of s-PPMS is not easily referable only to steric effects but seems to be dependant even on the chemical structure of the guest molecules. A comparison with syndiotactic polystyrene is also done.     

Five-membered ring chelate complexes of Ni(II), Pd(II) and Pt(II) derived of di-(2-pyridyl)-N-ethylimine

Cis-diaquobis{di-(2-pyridyl)-N-ethylimine}nickel(II) chloride (2) was obtained from the reaction of di-(2-pyridyl)-N-ethylimine (1) and [NiCl₂dppe] [dppe = cis-1,2-bis(diphenylphosphino)ethylene] in a 2:1 ratio in hot acetonitrile. Cis-dichloro{di-(2-pyridyl)-N-ethylimine}palladium(II) (3) and cis-dichloro{di-(2-pyridyl)-N-ethylimine}platinum(II) (4) complexes were obtained from the reaction of MCl₂ (M = Pd, Pt) and (1) in equimolar ratio in hot acetonitrile. Compounds 1–4 were characterized by IR spectroscopy, elemental analysis, and mass spectrometry; the complexes 3 and 4 were characterized in solution by NMR. In addition, solid state structures of compounds 1–4 were determined using single crystal X-ray diffraction analyses. X-ray diffraction data of the complexes 3 and 4 showed a distorted square planar local geometry at palladium and platinum atoms with the chlorine atoms in a cis-coordination; in 2 a local octahedral geometry at nickel atom was observed. Complexes 3 and 4 are arranged as dimers with a M?M distance of 3.4567(4) Å (M = Pd) and 3.4221(4) Å (M = Pt), respectively; 2 consists of units linked by intermolecular hydrogen bonding.     

A simple procedure for the esterification of alcohols with sodium carboxylate salts using 1-tosylimidazole (TsIm)

An efficient and selective method for esterification of alcohols using N-(p-toluenesulfonyl)imidazole (TsIm) is described. In this method, alcohols are refluxed with a mixture of RCO₂Na (R: alkyl and aryl), TsIm, and triethylamine in the presence of catalytic amounts of tetra-n-butylammonium iodide (TBAI) in DMF to afford the corresponding esters in good yields. This methodology is highly efficient for various structurally diverse alcohols with selectivity for ROH: 1° > 2° > 3°.     

Structural studies of cerium tantalates

Structural data obtained from neutron diffraction studies of some cerium tantalate phases are presented, including the first report of the high temperature structure of a CeTaO₄ phase, Ce_0.85TaO_3.84 deduced from in situ data recorded at 900°C in vacuum. It was found that this material transformed from the low temperature LaTaO₄ type phase to the orthorhombic A2₁am structure reported here, with a unit cell of a=5.64062(2) Å, b=14.81609(6) Å and c=3.93482(1) Å. This data agrees well with the previously proposed structural transformations.     

Synthesis of isotactic star-shaped poly(vinyl alcohol)

Isotactic 6-armed star-shaped poly(vinyl alcohol) (PVA) with a narrow molecular weight distribution was successfully prepared by the living cationic polymerization of 6-armed star-shaped poly(tert-butyl vinyl ether) (PTBVE) and subsequent acidic ether cleavage. The PTBVE was synthesized using hexa(chloromethyl) melamine (HCMM) as a hexafunctional initiator and ZnI₂ or ZnCl₂ as an activator in toluene/MC (1/1 v/v) at −70 °C. A better living stability of PTBVE was obtained in the ZnCl₂ activator system. The number average molecular weight and the polydispersity index of the 6-armed star-shaped PTBVE polymerized with ZnCl₂ at −70 °C for 24 h were 156,000 g/mol and 1.47, respectively. The fraction of the mm sequence of the resulting PVA was 52%.     

Oxidation of glyoxylic acid by a mononuclear manganese(IV) complex of 1,8-bis(2-hydroxybenzamido)-3,6-diazaoctane: A kinetics and mechanistic study

The oxidation of glyoxylic acid (HGl) by Mn^IVL {L⁴⁻ = tetra deprotonated 1,8-bis(2-hydroxybenzamido)-3,6-diazaoctane} was investigated in the pH range 1.67-10.18, at 25-45 °C and 0.5 M ionic strength. The reaction exhibited biphasic kinetics with Mn^IIIL⁻ as the reactive intermediate. Mn^IV was reduced to Mn^II. The products of oxidation of HGl were identified as formic acid and CO₂ in acidic medium, and oxalate in basic medium, consistent with the stoichiometry: −Δ[Mn^IV]/−Δ[HGl] = 1. In acidic medium, both Mn^IVL and Mn^IIIL⁻ formed outer-sphere adducts with the neutral HGl {HC(OH)₂COOH} molecule, with an association constant Q_av of 28 and 70 M⁻¹, respectively. A similar adduct formation was not observed for the glyoxylate mono anion {Gl⁻, CH(OH)₂(CO₂⁻)} and glyoxylate dianion {Gl²⁻, CH(OH)(O⁻)CO₂⁻}. The rate and activation parameters for the various paths are reported and an outer-sphere electron transfer mechanism is suggested.     

Crystal growth and structural investigation of A2BReO6 (A=Sr, Ba; B=Li, Na)

Single crystals of the double perovskite rhenates A₂BReO₆ (A=Sr, Ba; B=Li, Na) were grown out of molten hydroxide fluxes. Single crystals of orange/yellow Ba₂LiReO₆, Ba₂NaReO₆ and Sr₂LiReO₆ were solved in the cubic, Fm-3m space group with a=8.1214(11) Å, 8.2975(3) Å, and 7.9071(15) Å, respectively, while Sr₂NaReO₆ was determined to be monoclinic P2₁/n with a=5.6737(6) Å, b=5.7988(6) Å, c=8.0431(8) Å, and β=90.02(6) °. The cubic structure consists of a rock salt lattice of corner-shared ReO₆ and MO₆ (M=Li, Na) octahedra which, in the monoclinic structure, are both tilted and rotated. A discrepancy exists between the symmetry of Sr₂LiReO₆ indicated by the single-crystal refinement of flux-grown crystals (cubic, Fm-3m) and the symmetry indicated by the powder diffraction data collected on polycrystalline samples prepared by the ceramic method (tetragonal, I4/m). It is possible that the cubic crystals are a kinetic product that forms in small quantities at low temperatures, while the powder represents the more stable polymorph that forms at higher reaction temperature.     

Selection of entrainers in the 1-hexene/n-hexane system with a limited solubility

Vapor-liquid equilibria (VLE) have been measured for five 1-hexene/n-hexane/ionic liquid systems and 1-hexene/n-hexane/NMP (N-methyl-2-pyrrolidone) system with a headspace-gas chromatography (HSGC) apparatus at 333.15 K. The ionic liquids investigated were 1,3-dimethylimidazolium tetrafluoroborate [C₂MIM]⁺[BF₄]⁻, 1-butyl-3-methylimidazolium tetrafluoroborate [C₄MIM]⁺[BF₄]⁻, 1-methyl-3-octylimidazolium tetrafluoroborate [C₈MIM]⁺[BF₄]⁻, 1,3-dimethylimidazolium dicyanamide [C₂MIM]⁺[N(CN)₂]⁻ and 1-octylquinolinium bis(trifluoromethylsulfonyl)amide [C₈Chin]⁺[BTA]⁻. It was found that at low feeding concentration of 1-hexene and n-hexane, the separation ability of ionic liquids is in the order of [C₂MIM]⁺[BF₄]⁻ > [C₄MIM]⁺[BF₄]⁻ ≈ [C₂MIM]⁺[N(CN)₂]⁻ > [C₈MIM]⁺[BF₄]⁻ > [C₈Chin]⁺[BTA]⁻, which is consistent with the priori prediction of the COSMO-RS (conductor-like screening model for real solvents) model. But at high feeding concentration, the separation ability of ionic liquids is in the order of [C₂MIM]⁺[BF₄]⁻ < [C₄MIM]⁺[BF₄]⁻ ≈ [C₂MIM]⁺[N(CN)₂]⁻ < [C₈MIM]⁺[BF₄]⁻ < [C₈Chin]⁺[BTA]⁻. The liquid demixing effect should be taken into account. The activity coefficients of 1-hexene and n-hexane at infinite dilution calculated with the COSMO-RS model were correlated using the NRTL, Wilson and UNIQUAC model. In this work the predictive results from the COSMO-RS model and UNIFAC model for the 1-hexene/n-hexane and 1-hexene/n-hexane/NMP systems were compared. The UNIFAC model is one of the most important academic contributions by Prof. Jürgen Gmehling.     

Porosity development in chars from thermal decomposition of poly(p-phenylene terephthalamide)

The main objective of this work was to investigate the development of porosity in solid residues from the thermal decomposition of the polymer, poly(p-phenylene terephthalamide) (PPTA). PPTA chars were prepared at different temperatures and characterized by X-ray diffraction and physical adsorption of CO₂ at 0 °C. The carbonization temperatures were selected on the basis of thermogravimetric analysis results. The effect of introducing an isothermal treatment at 500 °C on the characteristics of the resulting chars was also studied. It was found that this pre-treatment lowers the decomposition temperature of PPTA and yields a somewhat less ordered material than in the case of pyrolysis under a constant heating rate. The micropore volume increases with increasing heat treatment temperature for both series of samples. The mean micropore size decreases for the two series of chars until the 700-800 °C interval; above these temperatures, this evolution is reversed. The micropore volume of the samples submitted to the isothermal treatment is higher than when PPTA is treated under a constant heating rate. Likewise, the pore size distribution is more heterogeneous when the intermediate isothermal treatment at 500 °C is introduced during PPTA pyrolysis. Some differences between porosity development in chars from PPTA and other high thermal stability polymers were explained on the basis of different mechanistic features in polymer pyrolysis.     

Formation of γ-Fe2O3 nanoparticles and vacancy ordering: An in situ X-ray powder diffraction study

The formation of maghemite, γ-Fe₂O₃ nanoparticles has been studied by in situ X-ray powder diffraction. The maghemite was formed by thermal decomposition of an amorphous precursor compound made by reacting lauric acid, CH₃(CH₂)₁₀COOH with Fe(NO₃)₃·9H₂O. It has been shown that cubic γ-Fe₂O₃ was formed directly from the amorphous precursor and that vacancy ordering starts about 45 min later at 305 °C resulting in a tripled unit cell along the c-axis. The kinetics of grain growth was found to obey a power law with growth exponents n equal to 0.136(6) and 0.103(5) at 305 and 340 °C, respectively. Particles with average sizes of 12 and 13 nm were obtained in 86 and 76 min at 305 and 340 °C, respectively. The structure of cubic and vacancy ordered phases of γ-Fe₂O₃ was studied at 305 °C by Rietveld refinements.     

Enhanced thermal stability of poly(1,4-dioxan-2-one) in melt by adding a chelator

Thermal stability of poly(p-dioxanone) (PPDO) was investigated isothermally and non-isothermally under air atmosphere using thermogravimetry (TG). The addition of 4-benzoyl-3-methyl-1-phenyl-2-pyrazolin-5-one (PMBP) could enhance successfully the thermal stability of PPDO compared with those of as-prepared and purified PPDO at temperature below about 230 °C. The activation energies for thermal degradation (ΔE_td) were evaluated at different weight loss values from TG data using the procedure recommended by MacCallum et al. The ΔE_td values of as-prepared PPDO, purified PPDO and PPDO containing 1.0 wt% PMBP were in the ranges of 20-50, 35-60, and 56-88 kJ mol⁻¹, respectively, when they were evaluated at weight loss values of 10-80%. The remaining weights increase with the amounts of PMBP added up to 1.5 wt%. The mechanism for the enhanced thermal stability of PPDO was discussed.     

Synthesis, characterization and Schlenk equilibrium studies of methylmagnesium compounds with O- and N-donor ligands - the unexpected behavior of [MgMeBr(pmdta)] (pmdta = N,N,N′,N″,N″-pentamethyldiethylenetriamine)

MgMe₂ (1) was found to react with 1,4-diazabicyclo[2.2.2]octane (dabco) in tetrahydrofuran (thf) yielding a binuclear complex [{MgMe₂(thf)}₂(μ-dabco)] (2). Furthermore, from reactions of MgMeBr with diglyme (diethylene glycol dimethyl ether), NEt₃, and tmeda (N,N,N′,N′-tetramethylethylenediamine) in etheral solvents compounds MgMeBr(L), (L = diglyme (5); NEt₃ (6); tmeda (7)) were obtained as highly air- and moisture-sensitive white powders. From a thf solution of 7 crystals of [MgMeBr(thf)(tmeda)] (8) were obtained. Reactions of MgMeBr with pmdta (N,N,N′,N″,N″-pentamethyldiethylenetriamine) in thf resulted in formation of [MgMeBr(pmdta)] (9) in nearly quantitative yield. On the other hand, the same reaction in diethyl ether gave MgMeBr(pmdta) · MgBr₂(pmdta) (10) and [{MgMe₂(pmdta)}₇{MgMeBr(pmdta)}] (11) in 24% and 2% yield, respectively, as well as [MgMe₂(pmdta)] (12) as colorless needle-like crystals in about 26% yield. The synthesized methylmagnesium compounds were characterized by microanalysis and ¹H and ¹³C NMR spectroscopy. The coordination-induced shifts of the ¹H and ¹³C nuclei of the ligands are small; the largest ones were found in the tmeda and pmdta complexes. Single-crystal X-ray diffraction analyses revealed in 2 a tetrahedral environment of the Mg atoms with a bridging dabco ligand and in 8 a trigonal-bipyramidal coordination of the Mg atom. The single-crystal X-ray diffraction analyses of [MgMe₂(pmdta)] (12) and [MgBr₂(pmdta)] (13) showed them to be monomeric with five-coordinate Mg atoms. The square-pyramidal coordination polyhedra are built up of three N and two C atoms in 12 and three N and two Br atoms in 13. The apical positions are occupied by methyl and bromo ligands, respectively. Temperature-dependent ¹H NMR spectroscopic measurements (from 27 to −80 °C) of methylmagnesium bromide complexes MgMeBr(L) (L = thf (4); diglyme (5); NEt₃ (6); tmeda (7)) in thf-d₈ solutions indicated that the deeper the temperature the more the Schlenk equilibria are shifted to the dimethylmagnesium/dibromomagnesium species. Furthermore, at −80 °C the dimethylmagnesium compounds are predominant in the solutions of Grignard compounds 4-6 whereas in the case of the tmeda complex7 the equilibrium constant was roughly estimated to be 0.25. In contrast, [MgMeBr(pmdta)] (9) in thf-d₈ revealed no dismutation into [MgMe₂(pmdta)] (12) and [MgBr₂(pmdta)] (13) even up to −100 °C. In accordance with this unexpected behavior, 1:1 mixtures of 12 and 13 were found to react in thf at room temperature yielding quantitatively the corresponding Grignard compound 9. Moreover, the structures of [MgMeBr(pmdta)] (9c), [MgMe₂(pmdta)] (12c), and [MgBr₂(pmdta)] (13c) were calculated on the DFT level of theory. The calculated structures 12c and 13c are in a good agreement with the experimentally observed structures 12 and 13. The equilibrium constant of the Schlenk equilibrium (2 9c ? 12c + 13c) was calculated to be K_gas = 2.0 × 10⁻³ (298 K) in the gas phase. Considering the solvent effects of both thf and diethyl ether using a polarized continuum model (PCM) the corresponding equilibrium constants were calculated to be K_thf = 1.2 × 10⁻³ and K_ether = 3.2 × 10⁻³ (298 K), respectively.     

Evaporation of ionic liquids at atmospheric pressure: study by ion mobility spectrometry

A conventional ion mobility spectrometry (IMS) was used to study atmospheric pressure evaporation of seven pure imidazolium and pyrrolidinium ionic liquids (ILs) with [Tf₂N], [PF₆], [BF₄] and [fap] anions. The positive drift time spectra of the as-received samples measured at 220 °C exhibited close similarity; the peak at reduced mobility K₀ = 1.99 cm² V⁻¹ s⁻¹ was a dominant spectral pattern of imidazolium-based ILs. With an assumption that ILs vapor consists mainly of neutral ion pairs, which generate the parent cations in the reactant section of the detector, and using the reference data on the electrical mobility of ILs cations and clusters, this peak was attributed to the parent cation [emim]. Despite visible change in color of the majority of ILs after the heating at 220 °C for 5 h, essential distinctions between spectra of the as-received and heated samples were not observed. In negative mode, pronounced peaks were registered only for ILs with [fap] anion.