Reactions at the interface of two immiscible polymers containing different reactive groups at either one end or both ends are studied with Monte Carlo (MC) simulations. The MC simulation shows that the copolymer concentration at the interface is shown to dramatically increase during the early stage of reaction and then levels off at a constant value. The effect of endfunctionality, i. e., the effect of the number of endfunctional groups, is also investigated. While the saturation value of interfacial coverage is proportional to the initial reactive polymer density for the case of mono‐endfunctional polymer, the simulation results with di‐endfunctional polymers show that the saturation copolymer coverage is not exactly proportional to the initial reactive polymer density in the case of high concentrations of the initial reactive polymer. This is believed to be caused by the change of conformation of block copolymers formed at the interface due to reaction: the fraction of loop conformation decreases while the tail fraction increases with a large amount of initial reactive di‐endfunctional polymer. Also, the experimentally determined time‐dependent interfacial fracture toughness, which is, in turn, related to the copolymer coverage at the interface, is in good qualitative agreement with the simulation results. 相似文献
This paper reports on the interfacial behaviour of block and graft copolymers used as compatibilizers in immiscible polymer blends. A limited residence time of the copolymer at the interface has been shown in both reactive blending and blend compatibilization by preformed copolymers. Polystyrene (PS)/polyamide6 (PA6), polyphenylene oxide (PPO)/PA6 and polymethylmethacrylate (PMMA)/PA6 blends have been reactively compatibilized by a styrene-maleic anhydride copolymer SMA. The extent of miscibility of SMA with PS, PPO and PMMA is a key criterion for the stability of the graft copolymer at the interface. For the first 10 to 15 minutes of mixing, the in situ formed copolymer is able to decrease the particle size of the dispersed phase and to prevent it from coalescencing. However, upon increasing mixing time, the copolymer leaves the interface which results in phase coalescence. In PS/LDPE blends compatibilized by preformed PS/hydrogenated polybutadiene (hPB) block copolymers, a tapered diblock stabilizes efficiently a co-continuous two-phase morphology, in contrast to a triblock copolymer that was unable to prevent phase coarsening during annealing at 180°C for 150 minutes. 相似文献
The very poor adhesion between films of styrene and acrylonitrile random copolymer (SAN) and maleic anhydride grafted polypropylene (PP‐g‐MA) can be dramatically improved by an intermediate thin layer of SAN bearing groups reactive toward maleic anhydride. The rate of the interfacial reaction, which is controlled by the reactive groups attached to SAN (amine vs. carbamate) and by the method used to build up the sandwich assembly, has a decisive effect on the capability of the SAN‐g‐PP graft copolymer formed at the interface to improve the fracture toughness in direct dependence on its molecular architecture. 相似文献
Summary: The effect of chain architecture of in situ formed copolymers on the interfacial morphology of reactive polymer blends was investigated. We found that the chain architectures of copolymers at the interface significantly affected the reaction and interface roughness. Although the amount of in situ formed Y‐shaped graft copolymers was smaller than that for diblock copolymers, the interface area generated by the former was larger than that generated by the latter.
Cross‐sectional TEM images for the mid‐sample reacted at 180 °C for different reaction times. 相似文献
The influence of polydispersity on the interfacial kinetics of end-coupling and microstructure formation in the melt of immiscible polymers was studied using dissipative particle dynamics simulations. The irreversible reaction started at a flat interface between two layers, each of which contained polymer chains of two different lengths with functionalized or unreactive end groups. As in the case of fully functionalized monodisperse reactants [A. V. Berezkin and Y. V. Kudryavtsev, Macromolecules 44, 112 (2011)], four kinetic regimes were observed: linear (mean field coupling at the initial interface), saturation (decreasing the reaction rate due to the copolymer brush formation or reactant depletion near the interface), autocatalytic (loss of the initial interface stability and formation of a lamellar microstructure), and terminal (microstructure ripening under diffusion control). The interfacial instability is caused by overcrowding the interface with the reaction product, and it can be kinetically suppressed by increasing chain length of the reactants. Main effects of polydispersity are as follows: (i) the overall end-coupling rate is dominated by the shortest reactive chains; (ii) the copolymer concentration at the interface causing its instability can be not the same as in the lamellas formed afterwards; (iii) mean length of the copolymer product considerably changes with conversion passing through a minimum when a microstructure is just formed. 相似文献
Recent developments in the field of reactive compatibilization of polymer blends prepared by melt processing focus on the addition of low molecular weight compounds. This work deals with in situ compatibilization through the formation of graft or crosslinked copolymers at the interface. Mixtures of semicrystalline hydrocarbon polymers have been subjected to free radical reactivity, in a co-rotating twin screw extruder (ZSK 30) in a single step. The particular system, high density polyethylene and polyamide 6, was blended in the presence of a peroxide and a reactive bifunctional monomer, maleic anhydride. Because of a combined effect, the reaction appears to occur mainly at the interface, where the resulting grafted copolymer acts as an anchor for the final stabilization of the biphasic system. Different analytical techniques, such as differential scanning calorimetry, scanning electron microscopy and tensile testing, helped in characterizing the resulting blends and confirmed the high level of interfacial grafting and the expected improvement in mechanical properties. 相似文献
A new reactive graft copolymer, poly (dimethyl siloxane )-graft-ω-hydroxyl-poly(ethylene oxide) (PDMS-g-(PEO--OH)), was synthesized by the hydrosilylation reactionof α, ω-bifunctional PEO macromonomer (CH_2=CH--CH_2--PEO--OH) with poly(hydromethylsiloxane) (PHMS). The obtained copolymer, exhibited the expected comb-like structure as indicated by the result of detailed characterization and the neededreactivity as demonstrated by the result of esterification between PDMS-g-(PEO--OH)and aminoacetic acid. This reactive graft copolymer is expected to be very useful in thepreparation of new bioactive polymer materials. 相似文献