聚天冬氨酸与钨酸钠复配对白铜B10的缓蚀作用

应用光电化学的方法研究了两种环境友好型缓蚀剂聚冬天氨酸(PASP)和钨酸钠(Na2WO4)的单一配方及其复配对白铜B10在硼砂-硼酸缓冲溶液中的缓蚀作用援研究表明, 在光电流循环伏安测试中, 单一的PASP与Na2WO4均能够使B10表面Cu2O膜引起的p型光电流响应增大, 这说明缓蚀剂增大了Cu2O膜的厚度, 使B10的腐蚀速率减小. 单一的PASP与Na2WO4的最佳添加浓度分别为3和5 mg·L-1, 单一的Na2WO4比单一的PASP使p型光电流响应增大趋势更大. 若以总浓度为5 mg·L-1时对两者进行复配, 当PASP与Na2WO4的质量浓度比为1:1和1:3时, 两者复配比单一使用时的p型电流光响应都更大, B10的腐蚀更小, 即缓蚀剂的效果更好. 交流阻抗测试结果与光电化学测试相一致.     

聚天冬氨酸和钨酸钠复配对3%NaCl溶液中白铜B10的缓蚀作用

应用交流阻抗法和极化曲线法,研究了两种环境友好型水处理药剂,即聚冬天氨酸(PASP)和钨酸钠的单一配方及其复配对白铜(B10)在3%NaC l溶液中的缓蚀效果.研究表明:单一聚冬天氨酸或钨酸钠配方对B10均具有一定的缓蚀效果,其中聚冬天氨酸以浓度为40 mg/L,钨酸钠以浓度为60 mg/L时的缓蚀效果最佳.总浓度为40 mg/L的两者复配具有更加明显的缓蚀效果并显示出协同效应,其中以聚冬天氨酸与钨酸钠配比为3∶1的缓蚀效果最佳.     

聚噻吩的光电化学研究

导电聚合物是由一些具有共轭π键的聚合物经化学或电化学掺杂后形成的导电率可从绝缘体延伸到导体范围的一类高分子材料。其中噻吩及其衍生物具有导电率高、环境稳定性好、成膜性好、禁带宽度小等特点,是用做光伏电池的理想材料。相继报道的有聚3-甲噻吩[1]、聚3-己基噻吩[2],聚(3-十一烷基-2,2’-并噻吩)[3]等。对于聚噻吩的光电化学性质的研究,在国际上很少见报道,国内尚未见报道,本文对聚噻吩(PTh)的光电化学性质进行了研究。1实验部分1.1仪器与试剂光电化学实验采用带石英窗口的三电极电解池,工作电极为ITO/PTh膜电极,参比电极为饱和…     

硫酸溶液中聚天冬氨酸对碳钢的吸附缓蚀性能

应用电化学极化曲线和交流阻抗研究聚天冬氨酸(PASP)对碳钢的缓蚀性能,讨论了PASP浓度和温度对缓蚀效果的影响.结果表明:PASP是一种以抑制阳极为主的缓蚀剂.在实验温度范围内,PASP在0.5mol/L硫酸溶液中对碳钢的缓蚀效率随着温度升高而降低,并以10℃时的缓蚀效果最好.在给定温度下,缓蚀率均随PASP浓度的增加而迅速增加,但当PASP质量浓度达到2.5g/L时,缓蚀率的增加趋于平缓,10℃下,缓蚀率的最高值可达80.33%(PASP 6.0g/L),PASP在碳钢表面的吸附基本服从Freund lich吸附等温式,PASP的加入增大了碳钢的腐蚀反应表观活化能.     

聚3-甲基噻吩的光电化学研究

利用光电化学方法研究了聚3-甲基噻吩的光电化学性质.其禁带宽度为1.93 eV.同时确定了它的价带、导带位置.研究还发现聚3-甲基噻吩属于直接跃迁半导体,具有很好的光电流稳定性.得到的最高IPCE值近1.0%.     

聚天冬氨酸的合成研究

以L-天冬氨酸为原料,磷酸为催化剂,在不同溶剂中进行缩聚反应,合成中间体聚丁二酰亚胺(PSI),当混合溶剂为m三甲苯／m环丁砜=7／3时,可得到较高分子量的PSI。当催化剂与单体的质量比为0．14时,分子量达到最大值。将PSI碱解得到聚天冬氨酸。     

SERS技术对聚天冬氨酸缓蚀性能的研究

SERS技术对聚天冬氨酸缓蚀性能的研究;缓蚀作用;表面增强拉曼散射     

聚吡咯纳米阵列电极的光电化学

以多孔的铝阳极氧化膜(AAO)为模板制备了直径约为80 nm聚吡咯(PPy)纳米线的阵列电极, 并研究了它的光电化学响应. 结果表明, 在电极电位低于－0.1 V(vs Ag/AgCl)时出现的阴极光电流是由聚吡咯纳米线的p型半导体性质引起的, 其平带电位为－0.217 V. 聚吡咯纳米线的长度对光电流的影响较大, 最佳长度为42 nm. 这是因为在很短的聚吡咯纳米线阵列中PPy太少, 产生的光电流弱, 而在过长的聚吡咯纳米线阵列中光生电子在到达电极基底前易于与光生空穴复合而消失. 聚吡咯纳米线有可能作为纳米光电器件用于未来微器件系统.     

绿色缓蚀剂聚天冬氨酸对铜的缓蚀性能与吸附行为

采用电化学阻抗和极化曲线法研究了绿色缓蚀剂聚天冬氨酸(PASP)对铜在200 mg·L-1的NaCl溶液中的缓蚀性能和吸附行为. 结果表明, 在20 ℃时, PASP使用的最佳浓度为15 mg·L-1, 缓蚀率可达到78.3%, PASP的吸附明显降低了Cl-的侵蚀, 属于阳极型缓蚀剂. 随着温度的升高, PASP的缓蚀性能下降. 在50 ℃时, PASP的缓蚀率下降至40.4%. PASP的吸附行为服从Langmuir吸附等温式,是自发的、放热的过程, 属于化学吸附.     

纳米钛酸锶薄膜电极的组装及其对不锈钢的光电化学缓蚀性能

研究了在铟锡氧化物（ITO）导电玻璃上组装的纳米钛酸锶薄膜光电极在模拟日光照射下对不锈钢的抗腐蚀保护性能.通过溶胶-凝胶法在添加和不添加十六烷基三甲基溴化铵（CTAB）表面活性剂的情况下制得了不同形貌的钛酸锶粉体.X射线衍射（XRD）和高分辨扫描电子显微镜（SEM）表征结呆表明,两种方法合成的钛酸锶均为钙钛矿型结构,但添加CTAB后得到的钛酸锶颗粒分散均匀,平均粒径为90 nm左右.采用紫外-可见漫反射光谱对钛酸锶薄膜的光物理性质进行了研究,发现其光吸收范围在紫外光区,而且通过CTAB协助合成的钛酸锶在小于380 nm光区较非CTAB协助合成的钛酸锶有更强的吸收.以0.1 mol·L^-1NaOH+0.2 mol·L^-1Na₂S溶液为光电极反应的电解质,测试了钛酸锶薄膜电极对304不锈钢在0.5 mol·L^-1的NaCI腐蚀溶液中的光电化学缓蚀性能.304不锈钢在CTAB改性钛酸锶薄膜光电化学保护或不保护条件在0.5 mol·L^-1NaCl+0.05 mol·L^-1HCl腐蚀溶液中腐蚀6h前后的表面金相图表明,钛酸锶薄膜具有优异的光电化学抗腐蚀性能.     

Electrochemical and Photoelectrochemical Study of Self‐assembled Monolayer of Phytic Acid on Brass

Phytic acid is an environment-friendly reagent for processing metals. The anticorrosion and inhibiting mechanism for phytic acid monolayers self-assembled on a brass (HSn70-1) electrode has been investigated by using electrochemical and photocurrent response methods. The electrochemical measurements indicate that phytic acid is liable to form surface complexes on the brass electrode, and the self-assembled monolayers (SAM) change the structure of the electric double-layer and shift the potential of zero charge positively. The photochemical measurement indicates that the brass electrode shows a p-type photoresponse owing to the formation of a Cu2O layer on its surface, and the presence of SAM weakens significantly the photoresponse, suggesting an excellent effect on anticorrosion, which is consistent with the EIS and polarization curve measurements. Adsorption of phytic acid was found to be typical of chemisorption, which can be reasonably described on the basis of the Langmuir isotherm.     

模拟水中白铜B30耐蚀性影响因素的光电化学研究

用动电位伏安法和光电化学方法对模拟水中白铜B30耐蚀性影响因素进行了研究. 白铜B30表面膜显示p-型光响应, 光响应来自电极表面的Cu₂O层, 在模拟水溶液中表面膜的半导体性质会发生转变, 由p-型转为n-型; 在不同 Cl^－, SO₄^2－浓度的模拟水溶液中, 电位正向扫描时呈现阳极光电流, 电位负向扫描时随着Cl^－, SO₄^2－离子浓度的增加, 光响应由p-型向n-型转变, 阳极光电流峰面积与阴极光电流峰面积之比增大, 耐蚀性能降低; 随着温度的升高, 白铜B30的耐蚀性能降低; 在pH＝7～9之间, 其耐蚀性能随着pH的升高而提高, 当pH＞9时, 其耐蚀性能随着pH的升高呈降低趋势.     

Croton lechleri Extracts as Green Corrosion Inhibitors of Admiralty Brass in Hydrochloric Acid

Croton lechleri, commonly known as Dragon’s blood, is a tree cultivated in the northwest Amazon rainforest of Ecuador and Peru. This tree produces a deep red latex which is composed of different natural products such as phenolic compounds, alkaloids, and others. The chemical structures of these natural products found in C. lechleri latex are promising corrosion inhibitors of admiralty brass (AB), due to the number of heteroatoms and π structures. In this work, three different extracts of C. lechleri latex were obtained, characterized phytochemically, and employed as novel green corrosion inhibitors of AB. The corrosion inhibition efficiency (IE%) was determined in an aqueous 0.5 M HCl solution by potentiodynamic polarization (Tafel plots) and electrochemical impedance spectroscopy, measuring current density and charge transfer resistance, respectively. In addition, surface characterization of AB was performed by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy techniques. Chloroform alkaloid-rich extracts resulted in IE% of 57% at 50 ppm, attributed to the formation of a layer of organic compounds on the AB surface that hindered the dezincification process. The formulation of corrosion inhibitors from C. lechleri latex allows for the valorization of non-edible natural sources and the diversification of the offer of green corrosion inhibitors for the chemical treatment of heat exchangers.     

模拟水中铜镍合金B10耐蚀性的光电化学研究

采用循环伏安、光电化学和电化学阻抗谱技术对模拟水中铜镍合金B10的腐蚀行为进行了研究.在电位从正往负向扫描中 B10表面膜显示p-型光响应,光响应来自电极表面的Cu2O层,但最大光电流比硼砂-硼酸中的要低。B10电极的耐蚀性能随着溶液中Cl-、SO42-和S2-浓度及pH的增加而降低。温度的升高会导致光电流由p-型转为n-型,耐蚀性能急剧下降。电化学阻抗谱测量结果与光电化学方法得到的结果相一致。     

钨酸盐对镁合金在3.5%NaCl介质中的缓蚀作用

研究钨酸钠对AZ61镁合金在3.5%NaC l腐蚀介质中的缓蚀作用.电化学阻抗谱(EIS)、Tafel极化曲线、扫描电子显微镜(SEM)等测试表明,钨酸钠缓蚀剂可有效抑制镁合金在NaC l介质中的腐蚀,当钨酸钠浓度为0.01 mol.L-1可达到较好的缓蚀效果,缓蚀效率达75.5%.钨酸钠可参与镁合金表面膜的形成,使表面膜更致密,从而抑制镁合金的腐蚀;其缓蚀作用属于阳极抑制型缓蚀机理.     

Natural Product-Derived Phosphonic Acids as Corrosion Inhibitors for Iron and Steel

Organic acids, typically derived from an oil-based value chain, are frequently used as corrosion inhibitors in industrial metal working fluids. The criteria for selection of these corrosion inhibitors have changed in the last decades, and are today not only performance-driven, but influenced by ecological considerations, toxicity and regulatory standards. We present scalable semisynthetic approaches to organic corrosion inhibitors based on phosphonic acids from renewable resources. They have been evaluated by chip filter assay, potentiodynamic polarization measurements, electrochemical impedance measurements and gravimetry for corrosion protection of iron and steel in an aqueous environment at slightly alkaline pH. The efficacy of several phosphonic acids tested was found to be strongly dependent on structural features influencing molecular self-assembly of protective layers, and the solubility of salts formed with di- and trivalent cations from the media or formed during corrosion. A carboxyphosphonic acid (derived from castor oil) was found to have remarkable anticorrosive effects in all media tested. We attribute the anticorrosion properties of this carboxyphosphonic acid to the formation of particularly stable protective layers on the metal surface. It might thus serve as a commercially attractive substitute for current acidic corrosion inhibitors, derived from renewable resources.     

铜钨杂多酸—耐尔蓝离子缔合显色反应及其应用

在阿拉伯胶存在下铜钨多酸与耐尔蓝形成离子缔子缔合物，其最大吸收位于５８０ｎｍ；表观摩尔吸光度ε值为２．２２＊１０＾６Ｌ．ｃｍ ＾－１；铜量在０－２４μｇ／Ｌ范围内服从比耳定律；检测限（３σ）１．０μｇ／Ｌ（ｎ＝１０）；分析１６μｇ／Ｌ铜的ＲＳＤ＝１．５％（ｎ＝１１）；离子缔合物的摩尔比为Ｃｕ：Ｗ：ＮＢ＝１：１２：４。     

钨化合物催化过氧化氢氧化环己酮合成己二酸

在无相转移催化剂的条件下,用Na2WO4·2H2O 或 H7[P(W2O7)6]·xH2O为催化剂,30% H2O2可以将环己酮高产率地氧化成己二酸.钨催化剂用量、反应液酸度对反应结果有着重要的影响.当钨原子与环己酮的摩尔比为1.5%,反应初始液的pH值为1.0时,己二酸的得率可达82%;而且催化体系具有很好的可循环性.