Graphene oxide based Pt-TiO2 photocatalyst: ultrasound assisted synthesis, characterization and catalytic efficiency

An ultrasound-assisted method was used for synthesizing nanosized Pt-graphene oxide (GO)-TiO₂ photocatalyst. The Pt-GO-TiO₂ nanoparticles were characterized by diffused reflectance spectroscopy, X-ray diffraction, N₂ BET adsorption-desorption measurements, atomic force microscopy and transmission electron microscopy. The photocatalytic and sonophotocatalytic degradation of a commonly used anionic surfactant, dodecylbenzenesulfonate (DBS), in aqueous solution was carried out using Pt-GO-TiO₂ nanoparticles in order to evaluate the photocatalytic efficiency. For comparison purpose, sonolytic degradation of DBS was carried out. The Pt-GO-TiO₂ catalyst degraded DBS at a higher rate than P-25 (TiO₂), prepared TiO₂ or GO-TiO₂ photocatalysts. The mineralization of DBS was enhanced by a factor of 3 using Pt-GO-TiO₂ compared to the P-25 (TiO₂). In the presence of GO, an enhanced rate of DBS oxidation was observed and, when doped with platinum, mineralization of DBS was further enhanced. The Pt-GO-TiO₂ catalyst also showed a considerable amount of degradation of DBS under visible light irradiation. The initial solution pH had an effect on the rate of photocatalytic oxidation of DBS, whereas no such effect of initial pH was observed in the sonochemical or sonophotocatalytic oxidation of DBS. The intermediate products formed during the degradation of DBS were monitored using electrospray mass spectrometry. The ability of GO to serve as a solid support to anchor platinum particles on GO-TiO₂ is useful in developing new photocatalysts.     

Ultrasound assisted synthesis of nano-sized lithium cobalt oxide

Nano-sized HT-LiCoO(2) powders were prepared by sonochemical synthesis in an aqueous solution of lithium hydroxide containing cobalt hydroxide at approximately 80 degrees C without any further heat treatment at high temperature. The effects of the LiOH concentration, oxidation conditions, ultrasound irradiation time and temperature on the formation of the nano-sized HT-LiCoO(2) phase were investigated. The formation of the HT-LiCoO(2) phase was confirmed by X-ray diffraction and Raman spectroscopy. The TEM images showed the presence of HT-LiCoO(2) aggregates with a mean particle diameter of approximately 20 nm. The reaction mechanism of the ultrasound assisted synthesis of nano-sized LiCoO(2) was proposed on the basis of the XRD, X-ray absorption spectroscopy analysis and TEM observation of the reaction products taken during the course of the synthesis.     

Thioglycolic acid (TGA) assisted hydrothermal synthesis of SnS nanorods and nanosheets

Nanorods and nanosheets of tin sulfide (SnS) were synthesized by a novel thioglycolic acid (TGA) assisted hydrothermal process. The as prepared nanostructures were characterized by X-ray diffraction (XRD) study, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). XRD study reveals the formation of well-crystallized orthorhombic structure of SnS. Diameter of the SnS nanorods varied within 30-100 nm. High-resolution transmission electron microscopy (HRTEM) and selected area electron diffraction (SAED) patterns identify the single crystalline nature for the SnS nanocrystals. The mechanism for the TGA assisted growth for the nanosheets and nanorods have been discussed.     

Ultrasound and microwave assisted synthesis of isoindolo-1,2-diazine: a comparative study

A comparative study, ultrasound (US) versus microwave (MW) versus conventional thermal heating (TH), for synthesis of isoindolo-1,2-diazine is described. The reaction pathway is fast, efficient and straight applicable, involving a Huisgen [3+2] dipolar cycloaddition of cycloimmonium ylides to 1,4-naphthoquinone. A feasible reaction mechanism for the obtaining of the fully aromatized tetra- and penta- cyclic isoindolo-1,2-diazine is presented. Under US irradiation the yields are much higher (sometimes substantially, by almost double), the reaction time decreases substantially, the reaction conditions are milder. The use of a generator with a higher nominal power induces higher yields and short reaction times. Overall the use of US it proved to be more efficient than MW or TH. A feasible explication for US efficiency is presented.     

Ultrasound assisted lipase catalyzed synthesis of poly-6-hydroxyhexanoate

Ultrasonic irradiation greatly improved the Candida antarctica lipase B mediated ring opening polymerization of ε-caprolactone to poly-6-hydroxyhexanoate in the ionic liquid 1-ethyl-3-methylimidazolium tetraflouroborate. Compared to the conventional nonsonicated reaction, sonication improved the monomer conversion by 63% and afforded a polymer product of a narrower molecular weight distribution and a higher degree of crystallinity. Under sonication, the polydispersity index of the product was ∼1.44 compared to a value of ∼2.55 for the product of the conventional reaction. With sonication, nearly 75% of the monomer was converted to product, but the conversion was only ∼16% for the reaction carried out conventionally. Compared to conventional operation, sonication enhanced the rate of polymer propagation by >2-fold and the turnover number of the lipase by >3-fold.     

Ultrasound assisted synthesis of Sn nanoparticles-stabilized reduced graphene oxide nanodiscs

Sn nanoparticles-stabilized reduced graphene oxide (RGO) nanodiscs were synthesized by a sonochemical method using SnCl₂ and graphene oxide (GO) nanosheets as precursors in a polyol medium. TEM and XPS were used to characterize the Sn-stabilized RGO nanodiscs.     

Ultrasound assisted synthesis of amide functionalized metal-organic framework for nitroaromatic sensing

Nano plates of zinc(II) based metal-organic framework (MOF) were prepared via ultrasonic method without any surfactants at room temperature and atmospheric pressure. Control of particle size and morphology was enhanced in this synthesis method. Nano plates of an interpenetrated amide-functionalized metal-organic framework, [Zn₂(oba)₂(bpfb)]·(DMF)₅, TMU-23, (H₂oba = 4,4′-oxybis(benzoic acid); bpfb = N,N′-bis-(4-pyridylformamide)-1,4-benzenediamine, DMF = N,N-dimethyl formamide), was synthesized under ultrasound irradiation in different concentrations of initial precursor. The nano structure and morphology of the synthesized MOF were characterized by Field Emission Scanning Electron Microscopy (FE-SEM), powder X-ray diffraction, thermo gravimetric analysis (TGA), elemental analysis and FTIR spectroscopy. Moreover, Fluorescence emissions of nanoplates have been studied. Amide-functionalized MOF shows high selectivity for sensing of nitroaromatic compounds such as nitrophenol, nitroaniline, and nitrobenzene in acetonitrile solution. Fluorescence intensity decreased with increasing contents of nitroaromatics in acetonitrile solution due to fluorescence quenching effect.     

Ultrasound assisted synthesis of isopropyl esters from palm fatty acid distillate

Esterification is one of the most preferred synthesis routes for organic esters which are most frequently used as plasticizers, solvents and perfumery and flavour chemicals. The present work deals with acid catalyzed synthesis of isopropyl esters from palm fatty acid distillate (PFAD) in the presence of ultrasonic irradiations operating at 25kHz frequency and 1kW of supplied power. Effect of different operating parameters such as molar ratio of reactants, catalyst quantity and operating temperature has been studied with an aim of optimization. It has been observed that ultrasound enhances the rate of reaction and the extent of equilibrium conversion. The optimum parameters for this process have been found to be 1:5 molar ratio of PFAD to isopropanol, catalyst concentration of 5% of PFAD and 60 degrees C reaction temperature. Maximum conversion levels of about 80% have been obtained in 6h of reaction time under these optimized conditions. Analysis of the kinetic data indicates that the reaction follows first order reversible path.     

Ultrasound assisted enzyme catalyzed synthesis of glycerol carbonate from glycerol and dimethyl carbonate

The present work illustrates the transesterification of glycerol to glycerol carbonate (GlyC) from dimethyl carbonate (DMC) using commercial immobilized lipase (Novozym 435) under ultrasonic irradiation. The experiments were performed in a batch reactor placed in an ultrasonic water bath using a sequence of experimental protocol to evaluate the effects of temperature, molar ratios of substrates, enzyme loading, duty cycle and ultrasound power on the conversion of glycerol to GlyC. It has been found that ultrasound-assisted lipase-catalyzed transesterification of glycerol would be a potential alternative to conventional alkali-catalyzed method, as high conversion (99.75%) was obtained at mild operating conditions: molar ratio of DMC to glycerol 3:1, catalyst amount of 13% (w/w), lower power input (100 W), duty cycle 50% and temperature (60 °C) in a relatively short reaction time (4 h) using Novozym 435 as catalyst. Ultrasound reduces the reaction time up to 4 h as compared to conventional stirring method (14 h) catalyzed by Novozym 435. The repeated use of the catalyst under the optimum experimental condition resulted in decay in both enzyme activity and product conversion.     

Ultrasound assisted microwave digestion

Simultaneous microwave and ultrasound irradiation is shown as a new technique for digestion of solid and liquid samples suitable for chemical and food analysis. Its application in analytical chemistry has been shown by decreases in digestion time: determination of copper in edible oils and total Kjeldahl nitrogen.     

Ultrasound assisted wet media milling synthesis of nanofiber-cage LiFePO4/C

To meet the objectives of the Intergovernmental Panel on Climate Change nations are adopting policies to encourage consumers to purchase electric vehicles. Electrification of the automobile industry reduces greenhouse gases but active metals for the cathode—LiCoO₂ and LiNiO₂—are toxic and represent an environmental challenge at the end of their lifetime. LiFePO₄ (LFP) is an attractive alternative that is non-toxic, thermally stable, and durable but with a moderate theoretical capacity and a low electrical conductivity. Commercial technologies to synthesize LFP are energy-intensive, produce waste that incurs cost, and involve multiple process steps. Here we synthesize LFP precursor with lignin and cellulose in a sonicated grinding chamber of a wet media mill. This approach represents a paradigm shift that introduces mechanochemistry as a motive force to react iron oxalate and lithium hydrogen phosphate at ambient temperature. Ultrasound-assisted wet media milling increases carbon dispersion and reduces the particle size simultaneously. The ultrasound is generated by a 20 kHz,500 W automatic tuning ultrasound probe. The maximum discharge rate of the LFP synthesized this way was achieved with cellulose as a carbon source, after 9 h milling, at 70% ultrasound amplitude. After 2.5 h of milling, the particle size remained constant but the crystal size continued to drop and reached 29 nm. Glucose created plate-like particles, and cellulose and lignin produced spindle-shaped particles. Long mill times and high ultrasound amplitude generate smoother particle surfaces and the powder densifies after a spray drying step.     

Ultrasound assisted synthesis of performic acid in a continuous flow microstructured reactor

The present work establishes in depth study of ultrasound assisted preparation of performic acid (PFA) in a continuous flow microstructured reactor. The influence of various parameters viz. formic acid: hydrogen peroxide molar ratio, flow rate, temperature and catalyst loading on the PFA formation were studied in a continuous flow microstructured reactor. In a continuous microstructured reactor in the presence of ultrasonic irradiation, the formation of PFA was found to be dependent on the molar ratio of formic acid: hydrogen peroxide, flow rate of reactants, temperature and catalyst loading (Amberlite IR-120H). The optimized parameter values are 1:1 M ratio, 50 mL/h, 40 °C and 471 mg/cm³ respectively. Further, the performance of Amberlite IR-120H catalyst was evaluated for three successive cycles in continuous microstructured reactor. The performance of catalyst was found to be decreased with the usage of the catalyst and is attributed to neutralization of the sulfonic acid groups, catalyst shrinkage, or loss in pore sites. The experimental results revealed that, for an ultrasound assisted synthesis of PFA in continuous microstructured reactor the observed reaction time was even less than 10 min. The observed intensification in the PFA synthesis process can be attributed to the intense collapse of the cavities formed at low temperature during ultrasonic irradiations, which further improved the heat and mass transfer rates with the formation of H₂O₂ during the reaction. The combined use of ultrasound and a continuous flow microstructured reactor has proved beneficial process of performic acid synthesis.     

Ultrasound and microwave assisted synthesis of dihydroxyacetophenone derivatives with or without 1,2-diazine skeleton

A thorough study concerning O-alkylation and α-bromination of dihydroxyacetophenone (DA) and N-alkylation of 1,2-diazine, under ultrasound (US) and microwave (MW) irradiation as well as under conventional thermal heating (TH) is presented. Under US and MW irradiation the yields are higher, the amount of used solvent decreases substantially, the reaction time decreases considerable (from hours or days to minutes) and the consumed energy decreases, consequently the O-alkylation, α-bromination and N-alkylation methods could be considered environmentally friendly. A selective and efficient way to either bis-O-alkylation or mono-O-alkylation of DA has been found, the relative position of the two hydroxyl groups on the phenyl moiety being compulsory. A selective and efficient way for α-bromination in heterogeneous catalysis of DA derivatives under US irradiation is presented. The N-alkylation reaction of DA under US and MW irradiation proved to be the most convenient setup procedure for these types of reactions. Overall, the use of US proved to be more efficient than MW or TH.     

Ultrasound with low intensity assisted the synthesis of nanocrystalline TiO2 without calcination

A novel method has been developed for the preparation of nano-sized TiO₂ with anatase phase. Nanoparticles with diameter about 6 nm were prepared at a relatively low temperature (75 °C) and short time. The synthesis was carried out by the hydrolysis of titanium tetra-isopropoxide (TTIP) in the presence of water, ethanol, and dispersant under ultrasonic irradiation (500 kHz) at low intensity. The results show that variables such as water/ethanol ratio, irradiation time, and temperature have a great influence on the particle size and crystalline phases of TiO₂ nanoparticles. Characterization of the product was carried out by different techniques such as powder X-ray diffraction (XRD), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM) and UV–vis spectroscopy.     

Ultrasound assisted two-stage biodiesel synthesis from non-edible Schleichera triguga oil using heterogeneous catalyst: Kinetics and thermodynamic analysis

Present work deals with the ultrasound-assisted biodiesel production from low cost, substantial acid value kusum (Schleichera triguga) oil using a two-step method of esterification in presence of acid (H₂SO₄) catalyst followed by transesterification using a basic heterogeneous barium hydroxide (Ba(OH)₂) catalyst. The initial acid value of kusum oil was reduced from 21.65 to 0.84 mg of KOH/g of oil, by acid catalyzed esterification with 4:1 methanol to oil molar ratio, catalyst concentration 1% (v/v), ultrasonic irradiation time 20 min at 40 °C. Then, Ba(OH)₂ concentration of 3% (w/w), methanol to oil molar ratio of 9:1, ultrasonic irradiation time of 80 min, and temperature of 50 °C was found to be the optimum conditions for transesterification step and triglyceride conversion of 96.8% (wt) was achieved. This paper also examined the kinetics as well as the evaluation of thermodynamic parameters for both esterification and transesterification reactions. The lower value of activation energy and higher values of kinetic constants indicated a fast rate of reaction, which could be attributed to the physical effect of emulsification, in which the microturbulence generated due to radial motion of bubbles, creates an intimate mixing of the immiscible reactants causing the increase in the interfacial area, giving faster reaction kinetics. The positive values of Gibbs-free energy (ΔG), enthalpy (ΔH) and negative value of entropy (ΔS) revealed that both the esterification and transesterification were non-spontaneous, endothermic and endergonic reactions. Therefore, the present work has not only established the escalation obtained due to ultrasonication but also exemplified the two-step approach for synthesis of biodiesel from non-edible kusum oil based on the use of heterogeneous catalyst for the transesterification step.     

Ultrasound assisted co-precipitation synthesis and catalytic performance of mesoporous nanocrystalline NiO-Al2O3 powders

Mesoporous nanocrystalline NiO-Al₂O₃ powders with high surface area were synthesized via ultrasound assisted co-precipitation method and the potential of the selected samples as catalyst was investigated in dry reforming reaction for preparation of synthesis gas. The prepared samples were characterized by N₂ adsorption (BET), X-ray diffraction (XRD), Temperature programmed reduction and oxidation (TPR, TPO) and scanning electron microscopy (SEM) techniques. The effects of pH, power of ultrasound irradiation, aging time and calcination temperature on the textural properties of the catalysts were studied. The sample prepared under specified conditions (pH10, 70 W, without aging time and calcined at 600 °C) exhibited the highest surface area (249.7 m² g⁻¹). This catalyst was calcined at different temperature and employed in dry reforming of methane and the catalytic results were compared with those obtained over the catalysts prepared by impregnation and co-precipitation methods. The results showed that the catalyst prepared by ultrasound assisted co-precipitation method exhibited higher activity and stability with lower degree of carbon formation compared to catalysts prepared by co-precipitation and impregnation methods.     

Hydrothermal synthesis and ferromagnetism of CuO nanosheets

Large quantity of CuO nanosheets was synthesized through hydrothermal method. The samples were characterized by X-ray diffraction, scanning electron microscope, transmission electron microscope and superconducting quantum interference device. The results showed that the as prepared samples are monoclinic phase CuO with width of about 500 nm, length of about 1000 nm and thickness of 40-50 nm. Magnetic measurements revealed ferromagnetism was existed in the CuO nanosheets. The ferromagnetism could be attributed to the uncompensated spins on the surface of the nanosheets.     

Ultrasound assisted one pot synthesis of imidazole derivatives using diethyl bromophosphate as an oxidant

A one pot, three-component condensation of benzoin/benzyl, an aldehyde, and ammonium acetate using diethyl bromophosphate as a mild oxidant is achieved to form trisubstituted imidazole compounds. Under ultrasound irradiation, a smooth condensation occurs to get the 2, 4, 5-triaryl-1H-imidazole compounds in good to excellent yields. The study explores the scope and limitation of diethyl bromophosphate as an oxidant and suggests advantages, viz., simplicity of operation, reduction in time, and an increase in product yields.     

Organic-phase synthesis of self-assembled gold nanosheets

Amphiphilic gold nanoclusters with the diameter of 1.8 ± 0.2 nm were prepared by decomposition of organometallic gold precursor CH₃AuPPh₃ in the presence of mercaptoacids in o-xylene. Self-assembly of the 16-mercaptohexadecanoic acid protected gold clusters led to the formation of the nanosheets consisted of aligned gold clusters. The hydrogen bonding between the carboxylic groups attached on the adjacent gold clusters likely drives the self-assembly. This phenomenon was cross-verified by employing the preheated mercaptoacid-amine surfactant system where a part of the mercaptoacids and amines were converted into –NH₃ ⁺–⁻OOC– ion pair and interrupting a part of the hydrogen bonding sites to lead to the reduction in the size of the structures from nanosheets to nanobelts. Interestingly, we found the dependency of the luminescent properties on the extent of maintaining the self-assembly of the clusters intern dictated by the surfactants.     

Ultrasound assisted synthesis of highly active nanoflower-like CoMoS4 electrocatalyst for oxygen and hydrogen evolution reactions

Rapid technological development requires sustainable, pure, and clean energy systems, such as hydrogen energy. It is difficult to fabricate efficient, highly active, and inexpensive electrocatalysts for the overall water splitting reaction: the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER). The present research work deals with a simple hydrothermal synthesis route assisted with ultrasound that was used to fabricate a 3D nanoflower-like porous CoMoS₄ electrocatalyst. A symmetric electrolyzer cell was fabricated using a CoMoS₄ electrode as both the anode and cathode, with a cell voltage of 1.51 V, to obtain a current density of 10 mA/cm². Low overpotentials were observed for the CoMoS₄ electrode (250 mV for OER and 141 mV for HER) at a current density of 10 mA/cm².