A facile preparation strategy for hollow-structured Bi2O3/Bi2WO6 heterojunction with high visible light photocatalytic activity

A hollow-structured heterojunction consisting of Bi₂WO₆ nanoplatelets and Bi₂O₃ nanoparticles was successfully prepared by a facile solvothermal process. Bi₂O₃/Bi₂WO₆ heterojunction is the aggregate of some hollow spheres with diameter ranging from several hundred nanometers to 1.5 μm and is connected to each other by tube-like cavums. On the basis of scanning and transmission electron microscopy observation and X-ray diffraction analysis of the samples synthesized at different reaction stages, a possible growth mechanism was proposed for the growth of hollow-structured Bi₂O₃/Bi₂WO₆ heterojunction. Its photocatalytic activity was evaluated by degradation of rhodamine B under visible-light irradiation (λ>400 nm). The results indicate that the hollow-structured Bi₂O₃/Bi₂WO₆ heterojunction exhibits much higher photocatalytic activity than both pure Bi₂WO₆ and pure Bi₂O₃. The improved photocatalytic performance can be ascribed to the heterojunction of Bi₂O₃ and Bi₂WO₆ in the framework in which the hierarchical hollow structure possesses good permeability and large surface area. More importantly, the hollow-structured Bi₂O₃/Bi₂WO₆ heterojunction is not only highly stable but also easy to be separated by simple sedimentation for recycle.     

Influence of electron beam irradiation on structural and optical properties of α-Ag2WO4 nanoparticles

The influence of 8 MeV electron beam irradiation on the structural and optical properties of silver tungstate (α-Ag₂WO₄) nanoparticles synthesized by chemical precipitation method was investigated. The dose dependent effect of electron irradiation was investigated by various characterization techniques such as, X-ray diffraction, scanning electron microscopy, UV–vis absorption spectroscopy, photoluminescence and Raman spectroscopy. Systematic studies confirm that electron beam irradiation induces non-stoichiometry, defects and particle size variation on α-Ag₂WO₄, which in turn results changes in optical band gap, photoluminescence spectra and Raman bands.     

Fabrication of Fe-doped TiO2 nanoparticles and investigation of photocatalytic decolorization of reactive red 198 under visible light irradiation

In this research, Fe-doped TiO₂ nanoparticles with various Fe concentrations (0. 0.1, 1, 5 and 10 wt%) were prepared by a sol–gel method. Then, nanoparticles were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis (EDX), BET surface area, photoluminescence (PL) spectroscopy and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic activity of the nano-particles was evaluated through degradation of reactive red 198 (RR 198) under UV and visible light irradiations. XRD results revealed that all samples contained only anatase phase. DRS showed that the Fe doping in the titania induced a significant red shift of the absorption edge and then the band gap energy decreased from 3 to 2.1 eV. Photocatalytic results indicated that TiO₂ had a highest photocatalytic decolorization of the RR 198 under UV irradiation whereas photocatalytic decolorization of the RR 198 under visible irradiation increased in the presence of Fe-doped TiO₂ nanoparticles. Among the samples, Fe-1 wt% doped TiO₂ nanoparticles showed the highest photocatalytic decolorization of RR198 under visible light irradiation.     

Synthesis and visible light photocatalysis water splitting property of chromium-doped Bi4Ti3O12

Photocatalysts Bi₄Ti_3 ? xCr_xO₁₂(x = 0.00, 0.06, 0.15, 0.30, 0.40, and 0.50) with perovskite structure were synthesized by sol–gel method and their electronic structures and photocatalytic activities were investigated. The Bi₄Ti_2.6Cr_0.4O₁₂ photocatalyst exhibited the highest performance of H₂ evolution in methanol aqueous solution (58.1 μmol h^? 1 g^? 1) under visible light irradiation (λ > 400 nm) without a co-catalyst, whereas no H₂ evolution is observed for Bi₄Ti₃O₁₂ under the same conditions. The UV–vis spectra indicated that the Bi₄Ti_2.6Cr_0.4O₁₂ had strong photoabsorption in the visible light region. The results of density functional theory (DFT) calculation illuminate that the conduction bands of Bi₄Ti₃O₁₂ are mainly attributable to the Ti 3d + Bi 6p orbitals, and the valence bands are composed of O 2p + Bi 6s hybrid orbitals, while the conduction bands of chromium-doped Bi₄Ti₃O₁₂ are mainly attributable to the Ti 3d + Bi 2p + Cr 3d orbitals, and the O 2p + Cr 3d hybrid obitals are the main contribution to the valence band.     

Synthesis of β-Bi2O3 towards the application of photocatalytic degradation of methyl orange and its instability

Bismuth oxide carbonate was synthesized from bismuth nitrate and potassium carbonate and then converted to phase pure β-Bi₂O₃ form by means of thermal decomposition. X-ray diffraction, HR-SEM, diffuse reflectance UV–vis and photocatalytic degradation studies were carried out on both the samples. Bi₂O₂CO₃ exhibited a wide band gap of 3.406(5) eV while β-Bi₂O₃ had a lesser band gap of 2.589(3) eV. β-Bi₂O₃ degrades a higher amount of methyl orange because of its lesser band gap and its optimum loading was 0.1 g in 50 ml of 10 ppm solution. After photocatalytic degradation Bi₂O₂CO₃ remains in the stable form whereas β-Bi₂O₃ changes to Bi₂O₂CO₃.     

Microwave synthesis of nitrogen doped Ti4O7 for photocatalytic applications

The nitrogen (N) doped Ti₄O₇ photocatalyst was prepared from urea as a nitrogen source by a microwave method. The resulting photocatalyst was characterized by X-ray diffraction (XRD), Field Emission Scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), UV–visible diffuse reflectance spectroscopy (UV–Vis DRS) and UV–vis spectroscopy (UV–Vis). 0.1 M N doped Ti₄O₇ photocatalyst exhibited methylene blue decomposition efficiency of 100% which was prepared by microwave treatment for above 30 min. Rate constant was found to be 0.028910 min⁻¹ in the first order kinetic.     

Synthesis of Hierarchical (BiO)2CO3 Nanosheets Microspheres toward Efficient Photocatalystic Reduction of CO2 into CO

In this paper, hierarchical (BiO)₂CO₃ nanosheets microspheres were synthesized with dry ice as carbon source, and characterized by X-ray diffraction (XRD) patterns, X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), high-resolution transmission electron microscopy (HRTEM) and UV–vis diffuse reflectance spectra (DRS). The photocatalytic results showed that (BiO)₂CO₃ display much higher photocatalytic activity than BiOCl and TiO₂ for photocatalystic reduction of CO₂ under UV-visible light. The photocatalytic mechanism study revealled that (BiO)₂CO₃ display better separation efficiency of photoinduced charge carriers due to the large interlayer spacing (1.3675 nm).     

Ultrasound assisted synthesis of TiO2–WO3 heterostructures for the catalytic degradation of Tergitol (NP-9) in water

TiO₂–WO₃ heterostructures were synthesized at room temperature, ambient pressure, and short reaction time via a sonochemical approach. TEM and EDX images show that the prepared TiO₂–WO₃ heterostructures consist of globular agglomerates (∼250 nm in diameter) composed of very small (<5 nm) dense particles (WO₃) dispersed inside the globules. The observed less intense monoclinic WO₃ diffraction peak (around 2θ = 22° belonging to (0 0 1) plane) and the high intense hexagonal WO₃ diffraction peak (around 2θ = 28° belonging to (2 0 0) plane) in XRD indicate that there may be phase transition occurring due to the formation of intimate bond between TiO₂ and WO₃. In addition, the formation of such new phase was also observed from Raman spectra with a new peak at 955 cm⁻¹, which is due to the symmetric stretching of W = O terminal. The catalytic activity of TiO₂–WO₃ heterostructures was tested for the degradation of wastewater pollutant containing Tergitol (NP-9) by a process combined with ozonation and it showed two-fold degradation rate compared with ozone process alone.     

The effects of Gd3+ doping on the physical structure and photocatalytic performance of Bi2MoO6 nanoplate crystals

Gd³⁺ doped Bi₂MoO₆ nanoplate crystals were fabricated by solvothermal combined calcination method. The effects of Gd³⁺ doping with different concentrations on the texture, crystal and optical properties of Bi₂MoO₆ were investigated by N₂ physical adsorption, X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FT-IR) and ultraviolet–visible diffuse reflection spectrum (UV–vis DRS), photoluminescence (PL) spectroscopy, and X-ray photoelectron spectroscopy (XPS). Under simulated solar light irradiation, the influences of Gd³⁺doping on photocatalytic activity of Bi₂MoO₆ were evaluated by photocatalytic degradation of Rhodamine B. The characterization results showed that with Gd³⁺ doping, a contraction of lattice and a decrease in crystallite size occurred. Meanwhile, an increase in surface area over Gd³⁺ doped Bi₂MoO₆ was observed. Moreover, Gd³⁺ doping could obviously enhance the visible light harvesting of Bi₂MoO₆ and promoted the separation of photogenerated electrons and holes. With optimum Gd³⁺(6 wt%) doping, Gd/Bi₂MoO₆ exhibited the best activity and stability in degradation of Rhodamine B.     

Ultrasound with low intensity assisted the synthesis of nanocrystalline TiO2 without calcination

A novel method has been developed for the preparation of nano-sized TiO₂ with anatase phase. Nanoparticles with diameter about 6 nm were prepared at a relatively low temperature (75 °C) and short time. The synthesis was carried out by the hydrolysis of titanium tetra-isopropoxide (TTIP) in the presence of water, ethanol, and dispersant under ultrasonic irradiation (500 kHz) at low intensity. The results show that variables such as water/ethanol ratio, irradiation time, and temperature have a great influence on the particle size and crystalline phases of TiO₂ nanoparticles. Characterization of the product was carried out by different techniques such as powder X-ray diffraction (XRD), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM) and UV–vis spectroscopy.     

Dielectric,optical and structural properties of Bi4V2−xSrxO11−δ (0.05≤x≤0.20)

Composition Bi₄V_2−xSr_xO_11−δ (0.05≤x≤0.20) is synthesized by melt quench technique followed by heat treatment at 800 °C for 12 h. These compounds are characterised by X-ray diffraction, Fourier transform infrared (FTIR) spectroscopy, UV–visible spectroscopy, impedance spectroscopy and scanning electron microscopy. X-ray diffraction patterns of all the samples show γ-phase stabilization at room temperature except x=0.05 heat treated sample. The optical band gap of all the samples is observed in semiconducting range. The lowest and the highest optical band gap is 2.39 eV and 2.57 eV for x=0.10 heat treated and x=0.20 quenched samples, respectively. The highest value of dielectric constant is obtained ~10⁷ with very low dielectric loss for x=0.15 and 0.20 samples at ~350 °C and below 10 Hz. The grain size increases with dopant concentration leads to increase the dielectric constant.     

Photocatalytic degradation of ciprofloxacin drug in water using ZnO nanoparticles

We report the synthesis of nanostructure ZnO semiconductor with ～2.1 nm diameter using a chemical precipitation method. The resulting nanoparticles were characterized by X-ray diffraction analysis (XRD), Fourier-transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The optical properties were investigated by UV–vis and fluorescence techniques. The absorption spectra exhibit a sharp absorption edge at ～334 nm corresponding to band gap of ～3.7 eV. The fluorescence spectra displayed a near-band-edge ultraviolet excitonic emission at ～410 nm and a green emission peak at ～525 nm, due to a transition of a photo-generated electron from the conduction band to a deeply trapped hole. The photocatalytic activity of the prepared ZnO nanoparticles has been investigated for the degradation of ciprofloxacin drug under UV light irradiation in aqueous solutions of different pH values. The results showed that the photocatalytic degradation process is effective at pH 7 and 10, but it is rather slow at pH 4. Higher degradation efficiency (～50%) of the drug was observed at pH 10 after 60 min. Photodegradation of the drug follows a pseudo-first-order kinetics.     

Effect of processing conditions on sonochemical synthesis of nanosized copper aluminate powders

Nanosized copper aluminate (CuAl₂O₄) spinel particles have been prepared by a precursor approach with the aid of ultrasound radiation. Mono-phasic copper aluminate with a crystallite diameter of 17 nm along the (3 1 1) plane was formed when the products were synthesized using Cu(NO₃)₂·6H₂O and Al(NO₃)₃·9H₂O as starting materials, with urea as a precipitation agent at a concentration of 9 M. The reaction was carried out under ultrasound irradiation at 80 °C for 4 h and a calcination temperature of 900 °C for 6 h. The synthesized copper aluminate particles and the effect of different processing conditions such as the copper source, precipitation agents, sonochemical reaction time, calcination temperature and time were analyzed and characterized by the techniques of powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM) and Fourier transformation infrared spectroscopy (FT–IR).     

Photocatalytic reduction of carbon dioxide with water using InNbO4 catalyst with NiO and Co3O4 cocatalysts

InNbO₄ was prepared by the solid-state reaction method. Various cocatalysts were added on InNbO₄ by the incipient-wetness impregnation method. The effects of co-catalyst and pretreatment conditions on the photocatalytic activity of InNbO₄ for photoreduction of carbon dioxide were investigated. NiO–InNbO₄ and Co₃O₄–InNbO₄ were pretreated by reduction at 500 °C for 2 h and subsequent oxidation at 200 °C for 1 h. The catalysts were characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and UV–vis diffuse reflectance spectroscopy. The characterization results of NiO–InNbO₄ catalysts after pretreatment showed the presence of highly crystalline NiO and monoclinic Nb₂O₅. NiO–InNbO₄ with reduction–oxidation pretreatment exhibited the highest activity due to the presence of core–shell type Ni⁰ and NiO on the surface and the presence of a small amount of Nb₂O₅ as a promoter.     

Synthesis and characterization of a new nano lead(II) 0-D coordination supramolecular compound: A precursor to produce pure phase nano-sized lead(II) oxide

Nano-structure of a new 0D Pb(II) coordination supramolecular compound, [Pb₄(8-Quin)₆](ClO₄)₂(1), L = 8-HQuin = 8-hydroxyquinolin ligand has been synthesized by use of a sonochemical process and characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRPD), Fourier transform infrared spectroscopy (FTIR) and elemental analyses. The structure of compound 1 was determined by single-crystal X-ray diffraction. The single crystal X-ray data of compound 1 implies that the Pb⁺² ions are five coordinated. Each lead atom is coordinated to nitrogen and oxygen atoms of 8-hydroxyquinolin ligand. Topological analysis shows that the compound 1 is 1,2,3,4,4M12-1net. Nanoparticles of lead(II) oxide have been prepared by calcination of lead(II) coordination polymer at 500 °C that were characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRPD) and IR spectroscopy.     

Sonochemical preparation of SbS1−xSexI nanowires

A sonochemical method for direct preparation of nanowires of SbS_1?xSe_xI solid solution has been established. The SbS_1?xSe_xI gel was synthesized using elemental Sb, S, Se and I in the presence of ethanol under ultrasonic irradiation (35 kHz, 2 W/cm²) at 50 °C for 2 h. The product was characterized by using techniques such as powder X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, energy dispersive X-ray analysis, selected area electron diffraction, and optical diffuse reflection spectroscopy. The SEM and HRTEM investigations exhibit that the as-prepared samples are made up of large quantity nanowires with lateral dimensions of about 10–50 nm and lengths reaching up to several micrometers and single-crystalline in nature. The increase of molar composition of Se affects linear decrease of the indirect forbidden optical energy gap as well as the distance between (121) planes of the SbS_1?xSe_xI nanowires.     

Scanning tunneling spectroscopy on Bi2SrCaCuO6+δ

Scanning tunneling microscopy and scanning tunneling spectroscopy (STS) measurements were performed on Bi₂SrCaCuO₆ whose superconducting transition temperature T_c is about 80 K. The superconducting gap obtained by the STS measurements was found to be about 40 meV. This value is close to that of optimally doped Bi₂Sr₂CaCu₂O₈ which has similar T_c. The observed spatial inhomogeneity of the gap value was much smaller than that of Bi₂Sr₂CuO₆.     

One-step simple sonochemical fabrication and photocatalytic properties of Cu2O–rGO composites

An easy, one-step synthesis of Cu₂O–reduced graphene composites (Cu₂O–rGO) was developed using a simple sonochemical route without any surfactants or templates. The morphology and structure of the Cu₂O–rGO composites were characterised using techniques such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). The results indicated that the Cu₂O sphere is approximately 200 nm in diameter and composed of small Cu₂O particles approximately 20 nm in diameter. The morphology and composition of the Cu₂O–rGO composites could be well controlled by simply changing the mole ratio of the reactants under ultrasonic irradiation. The Cu₂O–rGO composites displayed better photocatalytic performance for the degradation of methyl orange (MO) than pure Cu₂O spheres, which may have potential applications in water treatment, sensors, and energy storage.     

Sonochemical fabrication of gold nanoparticles–boron nitride sheets nanocomposites for enzymeless hydrogen peroxide detection

A simple sonochemical route was developed for the preparation of gold nanoparticles/boron nitride sheets (AuNPs/BNS) nanocomposites without using reducing or stabilizing agents. Transmission electron microscopy, scanning electron microscopy, X-ray diffraction, and UV–vis absorption spectra were used to characterize the structure and morphology of the nanocomposites. The experimental results showed that AuNPs with approximately 20 nm were uniformly attached onto the BNS surface. It was found that the AuNPs/BNS nanocomposites exhibited good catalytic activity for the reduction of H₂O₂. The modified electrochemical sensor showed a linear range from 0.04 to 50 mM with a detection limit of 8.3 μM at a signal-to-noise ratio of 3. The findings provide a low-cost approach to the production of stable aqueous dispersions of nanoparticles/BNS nanocomposites.     

Syntheses and structural characterization of two new nanostructured Bi(III) supramolecular polymers via sonochemical method

Two new bismuth(III) coordination supramolecular polymers, {[Bi₂(Hbpp)(bpp)(μ-I)₂I₆](Hbpp)·MeOH}_n (1) and [Bi(Hbpp)(Br₄)] (2), (bpp = 1,3-di(pyridin-4-yl)propane) were prepared and were structurally characterized by single crystal X-ray diffraction. Single crystalline one-dimensional materials were prepared using a heat gradient applied a solution of the reagents using the branched tube method. The structural determination by single crystal X-ray crystallography shows that compounds 1 and 2 form monoclinic polymers with symmetry space group P2₁ in the solid state. These new nanostructured Bi(III) supramolecular compounds, {[Bi₂(Hbpp)(bpp)(μ-I)₂I₆](Hbpp)·MeOH} (1) and [Bi(Hbpp)(Br₄)] (2), were also synthesized by sonochemical method. The nanostructures were characterized by Field Emission-scanning electron microscopy (FE-SEM), powder X-ray diffraction (PXRD) and IR spectroscopy.