Kinetic studies of glucose oxidase in polyelectrolyte multilayer films by means of scanning electrochemical microscopy (SECM)

Multilayer films of glucose oxidase (GOx) and poly(dimethyl diallyl ammonium chloride) (PDDA) prepared by layer-by-layer deposition were studied using scanning electrochemical microscopy (SECM). Aminated glass slides were coated with five bilayers of poly(styrene sulfonate) (PSS) and PDDA and used as substrates onto which GOx/PDDA multilayers were deposited. UV-Vis experiments confirmed multilayer growth, scanning force microscopic images provided morphological information about the films. SECM current-distance curves enabled the determination of kinetic information about GOx in GOx/PDDA multilayers as a function of layer number, film termination, inert covering layers, and enzyme substrate concentration after fitting to numerical models. The results indicate that only the topmost layers contributed significantly to the conversion. An odd-even pattern was observed for PDDA-terminated films or GOx-terminated films that correlated with morphological changes.     

Construction of glucose biosensor based on sorption of glucose oxidase onto multilayers of polyelectrolyte/nanoparticles

A new approach to constructing an enzyme-containing film on the surface of a gold electrode for use as a biosensor is described. A basic multilayer film (BMF) of (PDDA/GNPs) _n /PDDA was first constructed on the gold electrode by electrostatic layer-by-layer self-assembly of poly(diallyldimethylammonium chloride) (PDDA) and gold nanoparticles (GNPs). Glucose oxidase (GOx) was then sorbed into this BMF by dipping the BMF-modified electrode into a GOx solution. The assembly of the BMF was monitored and tested via UV-vis spectroscopy and cyclic voltammetry (CV). The ferrocenemethanol-mediated cyclic voltammograms obtained from the gold electrode modified with the (PDDA/GNPs) _n /PDDA/GOx indicated that the assembled GOx remained electrocatalytically active for the oxidation of glucose. Analysis of the voltammetric signals showed that the surface coverage of active enzyme was a linear function of the number of PDDA/GNPs bilayers. This result confirmed the penetration of GOx into the BMF and suggests that the BMF-based enzyme film forms in a uniform manner. Electrochemical impedance measurements revealed that the biosensor had a lower electron transfer resistance (R _et) than that of a sensor prepared by layer-by-layer assembly of PDDA and GOx, due to the presence of gold nanoparticles. The sensitivity of the biosensor for the determination of glucose, which could be controlled by adjusting the number of PDDA/GNPs bilayers, was investigated.     

二氧化硅纳米粒子薄膜的制备及光学性能

以二氧化硅胶体和聚二烯丙基二甲基氯化铵(PDDA)为原料,利用静电自组装技术制备了PDDA/SiO2复合薄膜. TEM图象显示,薄膜中的SiO2纳米粒子为密堆积,薄膜均匀、致密;电子衍射实验结果显示,所组装的薄膜为非晶态膜.载玻片表面组装SiO2纳米粒子薄膜后,透射率随薄膜双层数增加呈现周期变化.薄膜具有增透作用,载玻片双面组装薄膜后在一定波长范围内的透射率可提高5％以上. PDDA/SiO2复合薄膜的光学性质主要由SiO2纳米粒子决定,每一双层的平均物理厚度小于SiO2纳米粒子的粒径,薄膜中存在层间穿插现象,逐层组装的复合薄膜具有单层光学薄膜的特性.     

Layer-by-layer-assembled multilayer films of polyelectrolyte-stabilized surfactant micelles for the incorporation of noncharged organic dyes

Noncharged pyrene molecules were incorporated into multilayer films by first loading pyrene into poly(acrylic acid) (PAA)-stabilized cetyltrimethylammonium bromide (CTAB) micelles (noted as PAA&(Py@CTAB)) and then layer-by-layer (LbL) assembled with poly(diallyldimethylammonium chloride) (PDDA). The stable incorporation of pyrene into multilayer films was confirmed by quartz crystal microbalance (QCM) measurements and UV-vis absorption spectroscopy. The resultant PAA&(Py@CTAB)/PDDA multilayer films show an exponential growth behavior because of the increased surface roughness with increasing number of film deposition cycles. The present study will open a general and cost-effective avenue for the incorporation of noncharged species, such as organic molecules, nanoparticles, and so forth, into LbL-assembled multilayer films by using polyelectrolyte-stabilized surfactant micelles as carriers.     

Incorporation of glucose oxidase into Langmuir-Blodgett films based on Prussian blue applied to amperometric glucose biosensor

Glucose oxidase (GOx) was immobilized in the organic-inorganic Langmuir-Bldogett (LB) films consisting of octadecyltrimethylammonium (ODTA) and nanosized Prussian blue (PB) clusters. The amperometric glucose biosensors based on the LB films were fabricated and tested. It was found that the sensors exhibited a clear response current under an applied voltage of 0.0 V (vs Ag/AgCl). The linearity of current density versus glucose concentration was confirmed below 15 mmol/L concentration. This is the first observation of biosensor function of the hybrid organic-inorganic LB films. The successful preparation of glucose sensors operating at the very low potential indicates that the adsorbed PB clusters in the LB films act as an electrocatalyst for the electrochemical reduction of hydrogen peroxide, which is the final product of the enzymatic reaction sequence. The observed low potential applicability is estimated to inhibit the responses of interferants such as ascorbic acid, uric acid, and acetominophen. It was also found that an electrostatic interaction between positively charged ODTA+ and the adsorbed species of both GOx and PB provided a stabilized adsorption state in the LB films. Such stable immobilization contributes to the steady amperometric response current observed in the present ODTA/PB/GOx LB films.     

Multilayered construction of glucose oxidase on gold electrodes based on layer-by-layer covalent attachment

A feasible approach to construct multilayered enzyme film on the gold electrode surface for use as biosensing interface is described. The film was fabricated by alternate layer-by-layer deposition of periodate-oxidized glucose oxidase (GOx) and poly(allylamine) (PAA). The covalent attachment process was followed and confirmed by electrochemical impedance spectroscopy (EIS). X-ray diffraction (XRD) experiments revealed that the film was homogeneous and formed in an ordered manner with a thickness of 2.6 ± 0.1 nm per bilayer. The gold electrodes modified with the GOx/PAA multilayers showed excellent electrocatalytical response to the oxidation of glucose when ferrocenemethanol was used as an artificial redox mediator, which was studied by cyclic voltammetry (CV). From the analysis of voltammetric signals, the coverage of active enzyme on the electrode surface was estimated, which had a linear relationship with the number of GOx/PAA bilayers. This suggests that the analytical performance such as sensitivity, detection limit, and so on, is tunable by controlling the number of attached bilayers. The six GOx/PAA bilayer electrode exhibited a sensitivity of 15.1 μA mM⁻¹ cm⁻² with a detection limit of 3.8 × 10⁻⁶ M. In addition, the sensor exhibited good reproducibility and stability.     

Fabrication of free-standing multilayer films by using pH-responsive microgels as sacrificial layers

A facile way to prepare free-standing polyelectrolyte multilayer films of poly(sodium 4-styrenesulfonate)(PSS)/poly(diallyldimethylammonium)(PDDA) was developed by applying a new pH-dependent sacrificial system based on cross-linked poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA) microgels. The tertiary amine groups of PDMAEMA microgels can be protonated in acidic environment, and the protonated microgels were deposited by layer-by-layer (LbL) technique with PSS. PSS/PDDA multilayer films were constructed on the top of the PSS/microgels sacrificial layers. The LbL assembly process was investigated by UV–vis spectroscopy. Further study shows that the free-standing PSS/PDDA multilayer films can be obtained within 3 min by treating the as-prepared films in alkali aqueous solution with a pH of 12.0. The pH-triggered exfoliation of PSS/PDDA multilayer films provides a simple and facile way to prepare LbL assembled free-standing multilayer films.     

In situ fabrication of silver nanoarrays in hyaluronan/PDDA layer-by-layer assembled structure

We present a simple in situ method to fabricate silver (Ag) nanoparticle arrays in a layer-by-layer (LBL) assembled hyaluronan (HA)/poly(dimethyldiallylammonium chloride) (PDDA) multilayer structure, in which the LBL multilayered film is constructed by electrostatic attraction between positively charged PDDA and negatively charged HA, followed by in situ synthesis of embedded Ag nanoparticle arrays in the LBL "nanoreactors," where the abundant negatively charged carboxyl groups of HA bind and further reduce Ag(+) ions under UV-irradiating. The arrays morphology is highly dependent on the number of bilayers, and the surface density of nanoparticles in the arrays can be simply tailored by the number of irradiation/drying cycles during fabrication. The embedded Ag nanoparticle arrays possess good stability for localized surface plasmon resonance (SPR) absorption spectrum-based biosensors and superior antimicrobial capability. These render great potentials for the films in both biosensing and antimicrobial applications.     

静电层层自组装制备聚苯乙烯微球(核)/MCM-41纳米粒子(壳)阶层结构复合微粒

采用聚苯乙烯磺酸钠(PSS)和聚二烯丙基二甲基氯化铵(PDDA)两种聚电解质, 通过静电层层自组装成功地将MCM-41介孔二氧化硅纳米粒子包覆到聚苯乙烯(PS)微球表面. 实验结果表明, 当以尺寸为1.4 μm的PS微球为核时, 包覆了两个聚电解质双层(PDDA/PSS)2的PS(PDDA/PSS)2(PDDA/MCM-41)复合结构微粒与包覆了一个聚电解质双层(PDDA/PSS)的PS(PDDA/PSS)(PDDA/MCM-41)复合结构微粒相比, 复合结构微粒之间的交联程度降低, 但是MCM-41纳米粒子在聚苯乙烯微球表面的包覆都比较松散, 且产物中存在大量杂质. 而当以尺寸为5 μm的聚苯乙烯微球为核时, MCM-41纳米粒子紧密地包覆在聚苯乙烯微球表面, 复合结构微粒之间只有少量桥连物, 且产物中杂质很少.     

Adsorption and Electrooxidation of DNA at Glassy Carbon Electrodes Modified with Multiwall Carbon Nanotubes Dispersed in Glucose Oxidase

We are proposing for the first time the successful immobilization of DNA at glassy carbon electrodes (GCE) modified with carbon nanotubes (CNT) dispersed in glucose oxidase (GOx) (GCE/CNT‐GOx) either by direct adsorption or by layer‐by‐layer self‐assembling using polydiallyldimethylamine (PDDA). The presence of GOx allows an efficient dispersion of CNT and gives a most favorable environment that promotes the adsorption and makes possible a more sensitive electrooxidation of DNA. The PDDA incorporated in the self‐assembled architecture largely facilitates the adsorption and electrooxidation of dsDNA and the adsorbed layer can be successfully used for evaluating the interaction of DNA with methylene blue.     

Silver nanocomposite layer-by-layer films based on assembled polyelectrolyte/dendrimer

Silver nanocomposite multilayer films were prepared through the in situ method. Multilayer thin films, prepared through the sequential electrostatic deposition of a positively charged third-generation poly(amidoamine) dendrimer (PAMAM) and negatively charged poly(styrenesulfonate) (PSS) and poly(acrylic acid) (PAA), were utilized as nanoreactors for the formation of silver nanoparticles. The silver ions were preorganized in layer-by-layer (LBL) films composed of PAMAM dendrimers and subsequently reduced with hydrogen to prepare the silver nanoparticles. The UV-vis spectrum and profilometer were used to characterize the regular growth of bilayers. UV-vis absorption from plasmon resonance at 435 nm and TEM images indicated the formation of the silver nanoparticles in the multilayer films. The silver nanocomposite LBL films were also constructed on the indium tin oxide-glass and investigated using cyclic voltammetry. The silver nanoparticles in the multilayer films have a stronger negative redox potential. The silver nanocomposite LBL films may have a potential application in the catalysis of reduction of 4-nitrophenol with sodium borohydride.     

Immobilization and Characterization of Glucose Oxidase on Single-Walled Carbon Nanotubes and Its Application to Sensing Glucose

The negatively charged （at pH 8.2） glucose oxidase （GOx, pI ca. 4.2） was assembled onto the surface of single-walled carbon nanotubes （SWNT）, which was covered （or wrapped） by a layer of positively charged polyelectrolyte poly（dimethyldiallylammonium chloride） （PDDA）, via the electrostatic interaction forming GOx-PDDASWNT nanocomposites. Fourier transform infrared （FTIR）, UV-Vis and electrochemical impedance spectroscopy （EIS） were used to characterize the growth processes of the nanocomposites. The results indicated that GOx retained its native secondary conformational structure after it was immobilized on the surface of PDDA-SWNT. A biosensor （Nafion-GOx-PDDA-SWNT/GC） was developed by immobilization of GOx-PDDA-SWNT nanocomposites on the surface of glassy carbon （GC） electrode using Nafion （5%） as a binder. The biosensor showed the electrocatalytic activity toward the oxidation of glucose under the presence of ferrocene monocarboxylic acid （FcM） as an electroactive mediator with a good stability, reproducibility and higher biological affinity. Under an optimal condition, the biosensor could be used to detection of glucose, presenting a typical characteristic of Michaelis-Menten kinetics with the apparent Michaelis-Menten constant of KM^app ca. 4.5 mmol/L, with a linear range of the concentration of glucose from 0.5 to 5.5 mmol/L （with correlation coefficient of 0.999） and the detection limit of ca. 83 μmol/L （at a signal-to-noise ratio of 3）. Thus the biosensor was useful in sensing the glucose concentration in serum since the normal glucose concentration in blood serum was around 4.6 mmol/L. The facile procedure of immobilizing GOx used in present work would promote the developments of electrochemical research for enzymes （proteins）, biosensors, biofuel cells and other bioelectrochemical devices.     

Comparative bioelectrochemical study of core-shell nanocluster films with ordinary layer-by-layer films containing heme proteins and CaCO3 nanoparticles

Negatively charged heme protein hemoglobin (Hb) or myoglobin (Mb) at pH 9.0 and positively charged poly(diallyldimethylammonium) (PDDA) were alternately adsorbed on the surface of CaCO(3) nanoparticles, forming core-shell CaCO(3)-[PDDA/(protein/PDDA)(m)] ([protein-m]) nanoclusters. Oppositely charged [protein-m] and poly(styrenesulfonate) (PSS) were then assembled layer by layer on various solid substrates, forming {[protein-m]/PSS}(n) films. In the meantime, ordinary layer-by-layer films of heme proteins with CaCO(3) nanoparticles ({protein/CaCO(3)}(n)) were also grown on solid surfaces. Transmission electron microscopy (TEM), ultraviolet-visible (UV-vis) spectroscopy, quartz crystal microbalance (QCM), and cyclic voltammetry (CV) were used to characterize the nanoclusters and monitor the growth of the two types of films. Both kinds of protein films assembled on pyrolytic graphite (PG) electrodes exhibited well-defined, nearly reversible CV reduction-oxidation peaks, characteristic of heme Fe(III)/Fe(II) redox couples, and were used to catalyze the electrochemical reduction of hydrogen peroxide. The {[protein-m]/PSS}(n) films demonstrate distinct advantages over the {protein/CaCO(3)}(n) films due to their larger fraction of electroactive proteins, higher catalytic efficiency, and better thermostability. The penetration experiments of the electroactive probe into these films indicate that the {[protein-m]/PSS}(n) nanocluster films possess more pores or channels than the simple {protein/CaCO(3)}(n) films, which may be beneficial to counterion transport in the charge-hopping mechanism and helpful for the diffusion of catalysis substrates into the films. In addition, the electrochemical and biocatalytic activity of protein nanocluster films can be tailored by controlling the number of bilayers assembled on the nanoparticle cores (m) as well as the film thickness or the number of nanocluster layers on the electrodes (n).     

Double-layered TiO2-SiO2 nanostructured films with self-cleaning and antireflective properties

Dual function of self-cleaning and antireflection can be created in double-layered TiO2-SiO2 nanostructured films. The film were prepared by (1) layer-by-layer deposition of multilayered SiO2 nanoparticles with polydiallyldimethylammonium (PDDA) cations, (2) layer-by-layer deposition of multilayered titanate nanosheets with polications on PDDA/SiO2 multilayer films, and (3) burning out the polymer and converting titanate nanosheets into TiO2 by hearing at 500 degrees C. The as-prepared films, consisting of a porous SiO2 bottom layer and a dense TiO2 top layer, improved the transmittance of glass or quartz substrates, as demonstrated by transmission spectra collected at normal incidence. The photocatalytic properties of the films were studied by the change of the water contact angle together with the decay of the IR absorption of the hydrocarbon chain of octadecylphosphonic-acid-modified films under 2.6 mW cm-2 UV illumination. Both the antireflective and the photocatalytic properties of the films were dependent on the number of PDDA/nanosheet bilayers deposited. however, excellent surface wettability of the films for water was obtained, independent of the preparation conditions. The experimental findings are discussed in terms of the special structure of the double-layered nanostructured film.     

Headgroup effects of template monolayers on the adsorption behavior and conformation of glucose oxidase adsorbed at air/liquid interfaces

Stearic acid (SA) and octadecylamine (ODA) monolayers at the air/liquid interface were used as template layers to adsorb glucose oxidase (GOx) from aqueous solution. The effect of the template monolayers on the adsorption behavior of GOx was studied in terms of the variation of surface pressure, the evolution of surface morphology observed by BAM and AFM, and the conformation of adsorbed GOx. The results show that the presence of a template monolayer can enhance the adsorption rate of GOx; furthermore, ODA has a higher ability, compared to SA, to adsorb GOx, which is attributed to the electrostatic attractive interaction between ODA and GOx. For adsorption performed on a bare surface or on an SA monolayer, the surface pressure approaches an equilibrium value (ca. 8 mN/m) after 2 to 3 h of adsorption and remains nearly constant in the following adsorption process. For the adsorption on an ODA monolayer, the surface pressure will increase further 1 to 2 h after approaching the first equilibrium pressure, which is termed the second adsorption stage. The measurement of circular dichroism (CD) spectroscopy indicates that the Langmuir-Blodgett films of adsorbed GOx transferred at the first equilibrium state (π = 8 mN/m) have mainly a β-sheet conformation, which is independent of the type of template monolayers. However, the ODA/GOx LB film transferred at the second adsorption stage has mainly an α-helix conformation. It is concluded that the specific interaction between ODA and GOx not only leads to a higher adsorption rate and adsorbed amount of GOx but also induces a conformation change in adsorbed GOx from β-sheet to α-helix. The present results indicate that is possible to control the conformation of adsorbed protein by selecting the appropriate template monolayer.     

Polymer-Based Superhydrophobic Coating Fabricated from Polyelectrolyte Multilayers of Poly(allylamine hydrochloride) and Poly(acrylic acid)

Superhydrophobic films mainly based on poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) polyelectrolyte multilayer have been deposited onto cleaned glass substrate by a layer-by-layer dip coating method. 3 bilayers of the PAH and PAA was directly coated onto the substrate as an underlying layer for subsequent coating. Desired surface roughness on the polyelectrolyte bilayers was created by etching the bilayers in hydrochloric acid solution so as to create the open pore having suitable size at the surface. Then, nanoparticles such as SiO₂ and TiO₂ of various sizes were deposited onto the etched polyelectrolyte bilayers. Finally, the surfaces were further modified with semifluorinated silane followed by cross-linking at 180 °C for 2 h to obtain desirable surface morphological features. The effect of etching time and addition of nanoparticles on surface morphology was investigated using an atomic force microscope (AFM). Wetting ability of the prepared film was determined by measuring water droplet contact angle using a goniometer. Adhesion between the superhydrophobic films and the substrate was evaluated by using a standard tape test method (D3359). The adhesion was improved by reducing the organic content in the films.     

碳纳米管修饰电极同时测定邻苯二酚和对苯二酚

用十二烷基磺酸钠(SDS)分散碳纳米管(CNTs),通过层层组装(LBL)聚二甲基二烯丙基氯化铵(PDDA)和CNTs构筑PDDA/CNTs多层膜电极.利用紫外-可见光谱法对PDDA/CNTs多层膜的组装过程进行监测,用循环伏安法(CV)和差分脉冲伏安法(DPV)研究了邻苯二酚和对苯二酚同时存在时PDDA/CNTs多层膜电极上的电化学行为.结果表明,碳纳米管修饰电极对邻苯二酚和对苯二酚有较好的电催化活性和电分离作用,邻苯二酚和对苯二酚无需经过分离即可同时被检出.在修饰电极上的线性范围如下:邻苯二酚为2.0×10-6~1.4×10-4mol/L,线性相关系数R=0.9991;对苯二酚为2.0×10-6~1.4×10-4mol/L,线性相关系数R=0.9987.     

碳纳米管/聚二烯丙基二甲基氯化铵/磷钼酸复合膜的组装及其在溴酸盐检测中的应用

通过静电层层组装技术在玻碳(GC)电极表面制备{多壁碳纳米管(MWCNT)/聚二烯丙基二甲基氯化铵(PDDA)}n多层膜,并采用循环伏安法在多层膜的表面电化学修饰一层磷钼酸(PMo12)膜,构筑GC/{MWCNT/PDDA}n-PMo12复合膜修饰电极.利用SEM对比观察{MWCNT/PDDA}n和{PDDA/MWCNT}n-PMo12的微观结构,并研究该复合膜修饰电极的电化学及其对溴酸盐(BrO3-)电催化还原性质.在此基础上研发一种基于GC/{MWCNT/PDDA}n-PMo12复合膜修饰电极的电流型BrO3-传感器,该传感器表现出明显增大的响应电流.在最优的实验条件下,采用电流时间曲线(i-t)法考察该复合膜修饰电极对BrO3-的安培响应.实验结果表明,该传感器在BrO3-浓度为50～400nmol/L的范围内具有良好的线性关系,相关系数R2为0.9950,响应时间为1.53s,检出限为20nmol/L,灵敏度为13.81mA(mmol/L)-1cm-2.     

Supported lipid bilayers lifted from the substrate by layer-by-layer polyion cushions on self-assembled monolayers

The formation of lipid bilayers, lifted from the solid substrate by layer-by-layer polyion cushions, on self-assembled monolayers (SAMs) on gold was investigated by surface plasmon resonance (SPR) and fluorescence recovery after photobleaching (FRAP). The polyions poly(diallyldimethylammonium chloride) (PDDA) and polystyrene sulfonate (PSS) sodium salt were used for the layer-by-layer polyion macromolecular assembly. The cushion was formed by electrostatic interaction of PDDA/PSS/PDDA layers with a negatively charged surface of an SAM of 11-mercaptoundecanoic acid (MUA) on gold. The lipid bilayer membranes were deposited by vesicle fusion with different compositions of SOPS (an anionic lipid, 1-stearoyl-2-oleoyl-phosphatidylserine) and POPC (a zwitterionic lipid, 1-palmitoyl-2-oleoylphosphatidylcholine). In the case of pure SOPS and for lipid mixtures with a POPC composition up to 25%, single bilayers were deposited. FRAP experiments showed that single bilayers supported on PDDA/PSS/PDDA/MUA were mobile at room temperature, with lateral coefficients of approximately (1.2–2.1)×10⁻⁹ cm²/s. The kinetics of the addition of the ion-channel-forming peptide protegrin-1 to the supported bilayers was detected by SPR. A two-step interaction was observed, similar to the association behavior of protegrin-1 with bilayers supported on PDDA/MUA. The results are similar to that of supported lipid bilayers without a layer-by-layer cushion. The model membrane system in this work is a potential biosensor for mimicking the natural activities of biomolecules and is a possible tool to investigate the fundamental properties of biomembranes.     

Layer-by-layer assembled multilayer films of titanate nanotubes, Ag- or Au-loaded nanotubes, and nanotubes/nanosheets with polycations

Aqueous suspensions of hydrothermally synthesized titanate nanotubes and poly(diallyldimethylammonium chloride) (PDDA) have been employed to fabricate multilayer films on various substrates in a layer-by-layer fashion. Atomic force microscopy displays the dense coverage of the substrate surface by the nanotubes. UV-vis absorption spectroscopy confirms the consecutive growth of PDDA/nanotube layer pairs. Single crystalline Ag and Au nanoparticles with narrow size distribution spatially correlating with the nanotubes have been obtained by treating the nanotubes with AgNO(3) or HAuCl(4) aqueous solution followed by chemical reduction. The noble metal nanoparticles show a strong surface plasmon absorption band. A multilayer film construction of the noble-metal-loaded nanotubes has also been achieved. This process has been further extended to the heteroassembly of nanotubes/nanosheets in different layer sequences.