Analysis and regulation of unusual adsorption of phthalocyanine zinc(II) into a Nafion film as investigated by UV-vis spectroscopic techniques

Phthalocyanine zinc(II) (ZnPc) was found to be adsorbed well into a Nafion (Nf) film. The kinetic analysis suggested that the adsorption of ZnPc into the Nf film is controlled by its diffusion in the Nf film with a diffusion coefficient of D = 1.9 x 10(-6) cm(2) s(-1) that is higher than those (10(-9)-10(-12) cm(2) s(-1)) of cationic redox molecules in the Nf film by 3-6 orders of magnitude. The adsorption isothermal was analyzed by a Brunauer-Emmett-Teller (BET) equation suggesting multilayer adsorption of ZnPc into the film. The BET analysis provided the amount of ZnPc for monolayer adsorption (w(m) = 1.50 x 10(-7) mol cm(-2)), from which the effective area for the ZnPc adsorption was estimated to be larger by a factor of 1.7 x 10(3) than the Nf film area (1.0 cm(2)). The absorption spectra of a Nf film adsorbing ZnPc ((Nf/ZnPc)(ads) film) exhibited two broad absorption bands at 385 and 680-750 nm without any structural features, which is significantly different from the absorption spectra of either ZnPc solution in DMF or a (Nf/ZnPc)(mix) film prepared from a DMF solution containing Nf and ZnPc by solvent evaporation. This is ascribed to the formation of a ZnPc aggregate in the (Nf/ZnPc)(ads) film. Photoluminescence data for the (Nf/ZnPc)(mix) film suggested the presence of a ZnPc monomer and dimer at equilibrium in the film with a concentration of 0.1 M and that energy transfer occurs from the monomer to the dimer in excitation of the monomer (at lambda(ex) = 609 nm) to yield emission from the dimer. By contrast, photoluminescence data for the (Nf/ZnPc)(ads) film suggested that the excited ZnPc is self-quenched significantly by the formation of the ZnPc aggregate in the film. The lesser electroactivity of ZnPc in the (Nf/ZnPc)(ads) film compared with that in the (Nf/ZnPc)(mix) film could be ascribable to more difficult diffusion of ZnPc in the former film due to the formation of the ZnPc aggregate. The adsorption of ZnPc into the Nf film was significantly regulated by simple pretreatments of the Nf film such as immersion in solvents and storage under solvent vapors. The regulation was explained by controlled physical and chemical properties of a channel for mass and ion transport that is formed by sulfonate groups, countercations, and solvent molecules in the Nf film.     

Characteristics of a surface plasmon resonance sensor combined with a poly(vinyl chloride) film-based ionophore technique for metal ion analyses.

The characteristics of a surface plasmon resonance (SPR) sensor prepared by coating a metal film evaporated on a prism with a polymer film containing tetra-n-butyl thiuram disulfide (TBTDS) were studied. The differences in the sensitivity, selectivity, and detection limit for a Zn2+ ion of the SPR sensor were reported as a function of the thickness of the polymer film, the kind of a metal film, and the kind of a polymer film. The thinner was the polymer film, the higher was the sensitivity, and the lower was the detection limit. The Ag film gave to the SPR sensor higher sensitivity than the Au film. TBTDS contained in the poly(vinyl chloride) (PVC) film slightly improved the selectivity toward the Zn2+ ion. A non-conditioned poly(methyl methacrylate) (PMMA) film containing TBTDS gave a lower detection limit of 1.0 x 10(-6) mol/l, which is similar to that obtained by using an ion selective electrode (ISE) method, than the PVC film. The PVC film, however, gave higher concentration resolution than the PMMA film.     

On the adsorption and condensed film formation of dodecyl-, tetradecyl-, hexadecyl-, and octadecyltrimethylammonium bromides at the mercury/electrolyte interface

The adsorption and condensed film formation of dodecyl (DTAB)-, tetradecyl (TTAB)-, hexadecyl (CTAB)-, and octadecyl (OTAB)-trimethylammonium bromides on the hanging mercury electrode is studied in KBr as supporting electrolyte, at various temperatures from 5 to 45 degrees C. A condensed film is formed at negative potentials and at room temperature only in the presence of CTAB. The decrease of the temperature favors the formation of the condensed film. A transition temperature is observed for the film formation. Capacity-time curves at the potentials where the film is formed show a nucleation and growth mechanism, with induction time depending not only on the final potential but also on the initial potential range, although it is in the desorption region. In this temperature range no film is observed for DTAB and TTAB. However, the film is observed for OTAB, but only at higher temperatures, and is more easily formed with increasing temperature. The film is formed in a certain potential region and the nucleation rate increases while moving toward more negative potentials. Hysteresis phenomena are observed during changes of scan direction. The capacity vs time curves for OTAB, where condensed film is formed, are treated using an Avrami plot formulation and have been explained as progressive one-dimensional nucleation with a decrease of the nucleation rate during the overall film formation. The results show a marked effect of the chain length of the alkyl chain on the film formation.     

功能性超薄有序分子沉积膜的制备及其结构研究

1991年G.Decher等首次探讨了阴阳离子与聚电解质交替沉积制备有机超薄膜的方法。我们在完善成膜技术和发展成膜基质的基础上,详细研究了其成膜过程与膜的结构,并定义这种新的自组装超薄有序膜为分子沉积膜——MD膜。MD膜是利用阴阳离子的静电吸附反应特性,通过相反离子体系的交替分子沉积制备的层状有序自组装多层超薄膜。需要指出的是,分子沉积既是有机超薄膜的制备技术,本身又是一种自组装超薄有序膜。MD膜制备工艺简单,热稳定性和长期稳定性好,不受基体形状与面积限制。     

How fluorous is poly(2,2-bis(trifluoromethyl)-4,5-difluoro-1,3-dioxide-co-tetrafluoroethylene) (Teflon AF)?

We investigated poly(2,2-bis(trifluoromethyl)-4,5-difluoro-1,3-dioxide-co-tetrafluoroethylene (Teflon AF 2400, Tg = 240 degrees C), a stable and permeable fluorous polymer, as a transport/extraction medium for solutes for the first time. From the study of transport behavior of a series of solutes (in chloroform solution) through the film, and detailed measurement of the partitioning and diffusion of benzene in the film, we showed that the Teflon AF film is influenced by the solvent to which it is exposed. In particular, the solvent chloroform is sorbed in the film at a high concentration of 1.13 M. This plasticizes the film, so that the diffusion coefficient of benzene is about 3 orders of magnitude larger in a chloroform-equilibrated film compared to benzene coming from the gas phase into a "dry" film. The partition ratio of the polar solute 3-hydroxypyridine is dramatically higher in the case of partitioning between chloroform and a film (0.02) compared to partitioning between chloroform and the fluorous solvent FC-72 (6.7 x 10-5). Krytox FSH, a carboxylic acid terminated perfluoropolyether, plasticizes films. Tg in a 50% (w/w) film decreases to -40 degrees C. This carboxylic acid is capable of molecular recognition in the film. The noncovalent association between Krytox FSH (0.13 M in the film) and 3-hydroxypyridine increases the distribution ratio of the polar solute into the film by 41 times. In comparison, the partition ratio into a fluorocarbon solvent (FC-72) increases 15 000 times under the same conditions. As a result of imbibing organic solvent, the films of Teflon AF 2400 are not as fluorous as a fluorous liquid.     

一种卤键高分子多层膜的层层组装及其稳定性的提高

设计合成了聚甲基丙烯酸2-(4-碘-2,3,5,6-四氟苯氧基)乙酯( PIPEMA)和聚甲基丙烯酸3-(3-吡啶基)丙酯( PPyPMA),经过层层组装和随后的紫外可见光谱的检验,发现可以在丙酮和丁酮中组装PIPEMA/PPyPMA卤键多层膜,但是当以四氢呋喃(THF)或氯仿为组装溶剂时未能获得多层膜.另外,在丁酮中...     

波长检测型表面等离子体共振传感器对硫堇电聚合成膜的原位分析

利用波长检测型表面等离子体共振(SPR)传感器对硫堇在金膜表面的电化学聚合成膜过程进行了跟踪分析.结果表明,在固定入射角下SPR共振波长随循环伏安扫描周数的增加而线性红移,表明聚硫堇膜的生长是匀速的;扫描100周后共振波长红移总量为96.6 nm.对该实验结果进行理论拟合,得出聚硫堇膜的厚度约为71 nm.聚硫堇膜在酸性缓冲液中的电化学活性很高,其电化学反应过程受扩散控制,在一个完整的循环伏安扫描过程中SPR共振波长的变化完全可逆,说明聚硫堇膜的氧化反应和还原反应是一对可逆过程.与还原态聚硫堇膜相比,氧化态聚硫堇膜对应的SPR共振波长较大,说明氧化态聚硫堇膜折射率高.     

Determining the effects of vapor sorption in polymers with the quartz crystal microbalance/heat conduction calorimeter

The quartz crystal microbalance/heat conduction calorimeter (QCM/HCC) is a versatile instrument coupling both gravimetric and calorimetric techniques. The QCM/HCC is used to probe vapor sorption in thin films. Three parameters are measured simultaneously as a thin film undergoes vapor sorption, namely: mass changes in the film (±10 ng), corresponding thermal effects upon vapor sorption (±100 nW), and motional resistance (±0.5Ω) changes within the film. A range of film thicknesses (0.75 to 8.5 μm) of the polymer, Tecoflex? are cast on QCMs and the interaction of each film with ethanol and water is determined. From the direct calorimetric measurements, sorption enthalpies (Δ_sorptionH kJ/mol) are determined for the film–vapor interactions. Sorption isotherms are then analyzed for each film. The isotherms shown here generally display a linear Henry's Law dissolution relationship between the vapor pressure and the amount of vapor sorbed into the film. Motional resistance data provides a window to view viscoelastic effects of the polymer films upon vapor sorption. Motional resistance data are compared for ethanol sorption in a relatively thin (0.75 μm) and thicker (8.5 μm) Tecoflex? film. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3893–3906, 2004     

Extraction and Purification of Purple Membrane for Photochromic Thin Film Development: Application in Photoelectrochemical Investigation

Purple membrane (PM) has been extracted and purified from archaebacteria for thin film development. The purified purple membrane is isolated in 1?% polyvinyl alcohol solution for making thin film within gelatin and organically modified silicate matrices. For thin film within gelatin matrix, homogenized purple membrane suspension is mixed with 8?% gelatin and poured into a specially designed block with desired thickness of spacer having hydrophobicity followed by gelatinization of the same over home-made thermostatic control unit at 38?°C. The gelatinized matrix is then allowed to dry under controlled conditions of humidity and temperature. The films of varying thicknesses ranging between 40, 50, and 60??? are used for photo-electrochemical measurements. The results on photo-electrochemistry of non-oriented purple membrane film provides valuable information on the generation of forward (light on) and backward (light off) photocurrent as a function of: (a) applied potential and (b) film thickness. An increase in applied negative potential increases the amplitude of photocurrent whereas decrease in film thickness facilitates the reversibility of photocurrent response.     

Facile formation of water-insoluble cyclodextrin/Nafion composite films on solid surfaces

The water-insoluble poly-beta-cyclodextrin (poly-CD)/Nafion composite film was easily prepared by casting a mixed solution of poly-CD and Nafion onto substrate plates. FT-IR measurements showed that the 50/50 wt% poly-CD/Nafion composite film remained stable on the glass and quartz substrates after immersion in water for more than 3 h, while a pure poly-CD film was almost completely dissolved by immersion within 1 h. The film stability was also evaluated from the amount of p-nitrophenol (p-NP) inclusion in the film, which was determined from the decrease in UV-vis absorbance of the p-NP solution into which the film was immersed. The composition dependence of the inclusion amount showed that the film was stable up to 50 wt% CD, but became less stable with further increase in the CD concentration in the film. From the isotherms for the inclusion of p-NP and 1-naphthoate (1-Naph) into the film, the inclusion (stability) constants were determined to be 3.7x10(3) M(-1) and 1.9x10(2) M(-1), respectively. These results show that the selective inclusion of CD is retained after preparation of the composite film.     

Copper–mercury film electrode for cathodic stripping voltammetric determination of Se(IV)

The copper-mercury film electrode has been suggested for the determination of Se(IV) in a wide range of concentration from 1x10(-9) to 1x10(-6) mol L(-1)by square-wave cathodic stripping voltammetry. Insufficient reproducibility and sensitivity of the mercury film electrode have been overcome by using copper(II) ions during the plating procedure. Copper(II) has been found to be reduced and form a reproducible copper-mercury film on a glassy carbon electrode surface. The plating potential and time, the concentration of copper(II) and the concentration of the supporting electrolyte have been optimised. Microscopy has been used for a study of the morphology of the copper-mercury film. It has been found that it is the same as for the mercury one. The preconcentration step consists in electrodeposition of copper selenide on the copper-mercury film. The relative standard deviation is 4.3% for 1x10(-6) mol L(-1) of Se(IV). The limit of detection is 8x10(-10) mol L(-1) for 5 min of accumulation.     

An ionic surfactant-mediated Langmuir-Blodgett method to construct gold nanoparticle films for surface-enhanced Raman scattering

A gold nanoparticle film for surface-enhanced Raman scattering (SERS) was successfully constructed by an ionic surfactant-mediated Langmuir-Blodgett (LB) method. The gold film was formed by adding ethanol to a gold colloid/hexane mixture in the presence of dodecyltrimethylammonium bromide (DTAB). Consequently, gold nanoparticles (AuNPs) assembled at the water/hexane interface due to the decrease in surface charge density of AuNPs. Since DTAB binds the gold surface by a coulombic force, rather than a chemical bonding, it is easily replaced by target molecules for SERS purposes. The SERS enhancement factor of the 80 nm gold nanoparticle film was approximately 1.2 × 10(6) using crystal violet (CV) as a Raman dye. The SERS signal from the proposed DTAB-mediated film was approximately 10 times higher than that from the octanethiol-modified gold film, while the reproducibility and stability of this film compared to an octanethiol-modified film were similar. This method can also be applied to other metal nanostructures to fabricate metal films for use as a sensitive SERS substrate with a higher enhancement factor.     

Liquid phase deposition of hemoglobin/SDS/TiO2 hybrid film preserving photoelectrochemical activity

This work demonstrates that liquid phase deposition (LPD) technique provides a novel approach to the immobilization of hemoglobin (Hb) in TiO(2) film for studying the direct electron transfer of Hb. Using the LPD process, a hybrid film composed of Hb, TiO(2) and sodium dodecylsulfonate (SDS) is successfully prepared on the electrode surface. The surface morphology of as-deposited Hb/SDS/TiO(2) film shows a flower-like structure. The cyclic voltammetric measurement indicates that the LPD hybrid film facilitates the electron transfer of Hb, which yields a pair of redox peaks prior to the characteristic voltammetric peaks of TiO(2). Due to the electrocatalytic activity of Hb towards H(2)O(2), the Hb/SDS/TiO(2) hybrid LPD film can be utilized as an H(2)O(2) sensor, showing a sensitive response linearly proportional to the concentration of H(2)O(2) in the range of 5.0×10(-7)-4.0×10(-5) mol/L. At the same time, the Hb/SDS/TiO(2) hybrid film preserves the photoelectrochemical activity of TiO(2). The photovoltaic effect on the electrochemical behavior of Hb/SDS/TiO(2) film is observed after long-time UV irradiation on the film, which could improve the calibration sensitivity for H(2)O(2).     

Single-walled carbon nanotube (SWNT)-carboxymethylcellulose (CMC) dispersions in aqueous solution and electronic transport properties when dried as thin film conductors

Obtaining uniformly dispersed SWNT within an aqueous mixture for subsequent use as a dried coating in electronic biosensors is a challenge. The objective of this study is to relate SWNT dispersion conditions to resultant dried film properties. Aqueous solutions of SWNT dispersed with CMC (a dispersing agent with unique properties compatible with biomolecules) at different SWNT:CMC weight ratios and at different sonication conditions were studied. Solution particle size distribution data was obtained using dynamic light scattering. Differently formulated/processed SWNT/CMC solutions were used to form dry thin, conductive films. The resistance of each film was measured and its resistivity calculated. Response Surface Methodology (RSM) design of experiments (DOE) analysis was used as the tool to fit the data to establish a model and identify trends for the parameters studied. Profilometry was used to examine film surface uniformity. 3D optical microscopy was used to investigate film morphology and determine film thickness, and to relate these data back to solution dispersion conditions and dried film resistances. The lowest dried film resistivity (0.012 ohm-cm) was obtained at the highest levels of parameters studied in the DOE. Smaller solution particle size resulted in lower dried film surface roughness and better film uniformity.     

用反射隔离层来改善双面X射线胶片的成像能力

设计了一种新型结构的双面X射线胶片,在片基和乳剂层之间各加了一个反射隔离层。这种结构可以防止交叉曝光对影像质量的损害,不但不会使感光度降低,还能有所提高。     

Development of Stimulus‐Responsive Degradable Film via Codeposition of Dopamine and Cystamine

Herein, we report a degradable film that can be coated on various substrates by the codeposition of dopamine and cystamine. The thickness of the resulting film (pDC) varies depending on the initial ratio of dopamine/cystamine dissolved in a solution; the thickest film (ca. 60 nm) is obtained under optimized codeposition conditions. Selective degradation of pDC occurs in the presence of tris(2‐carboxyethyl)phosphine (TCEP), the reaction kinetics of which are highly dependent on the TCEP concentration. For further application as a drug‐delivery platform, doxorubicin can be loaded within the pDC film, which is released actively under film degradation in response to TCEP. We expect that the developed pDC film will be a useful tool for developing drug delivery cargo, antibacterial surface, and cell surface coating for various biomedical applications.     

Facile fabrication of large area of aggregated gold nanorods film for efficient surface-enhanced Raman scattering

An effective and facile method for fabrication of large area of aggregated gold nanorods (AuNRs) film was proposed by self-assembly of AuNRs at a toluene/water interface for the first time. It was found that large area of aggregated AuNRs film could be formed at the interface of toluene and water due to the interfacial tension between the two phases. The obtained large area of aggregated AuNRs film exhibits strong surface-enhanced Raman scattering (SERS) activity with 4-aminothiophenol (4-ATP) and 2-aminothiophenol (2-ATP) as the probe molecules based on the strong electromagnetic coupling effect between the very adjacent AuNRs. Enhancement factors (EF) were used to estimate the SERS activity of the aggregated AuNRs film, which is obtained to be 1.7x10(5) for 7a vibration of 4-ATP. SERS intensity is compared with AuNRs deposited directly on glass, indicating high SERS activity and reproducibility of the aggregated AuNRs film. In addition, SERS activity has also been successfully demonstrated for dye molecule (Rhodamin 6G (R6G)) and biological small molecule (adenine) on the aggregated AuNRs film, showing great potential of the aggregated AuNRs film as a convenient and powerful SERS substrate for biological tags and biological molecular detection.     

薄膜表面等离子体光催化剂Ag@AgBr/CNT/Ni的制备和性能

用复合电沉积技术制备了Ag@AgBr/CNT/Ni表面等离子体薄膜催化剂,以扫描电镜(SEM)、X射线衍射(XRD)、拉曼光谱(Raman Spectra)、X射线光电子能谱(XPS)和紫外-可见漫反射光谱(UV-Vis DRS)对薄膜的表面形貌、晶体结构、化学组成和光谱特性进行了表征,在可见光照射下,用罗丹明B(RhB)作为模拟污染物对薄膜的光催化性质和稳定性进行测定,采用测定薄膜电化学阻抗谱(EIS)和向反应系统中加入活性物种捕获剂的方法对薄膜光催化机制进行探索。结果表明:最优工艺下制备的Ag@AgBr/CNT/Ni薄膜是由少量碳纳米管(CNT)和表面沉积纳米Ag粒子的AgBr晶体构成的复合薄膜。薄膜具有突出的表面等离子体共振效应、优异的光催化活性和良好的催化稳定性。光催化罗丹明B 20 min,Ag@AgBr/CNT/Ni薄膜的降解率是Ag@AgBr/Ni薄膜的1.32倍,是P25 TiO_2/ITO多孔薄膜的21.6倍。在保持光催化性能基本不变的前提下可循环使用5次。CNT的存在使薄膜电荷传导性能和光催化还原溶解氧的性能大幅增加,是所制薄膜相对于Ag@AgBr/Ni薄膜光催化性能提高的主要原因。提出了薄膜光催化罗丹明B的反应机理。     

双极性半导体钝化膜空间电荷电容分析

钝化膜的空间电荷电容的测量(Mott-Schottky(M-S)曲线)是研究其半导体性质的重要手段, 双极性半导体钝化膜在耗尽态电位区M-S曲线斜率往往会发生改变, 首先建立了半导体富集态、耗尽态以及反型态空间电荷电容的统一计算公式, 进而将双极性半导体钝化膜空间电荷电容等效为钝化膜/溶液界面处电容和内层钝化膜/外层钝化膜界面处的np结电容的串联, 模拟计算结果能够很好地解释M-S曲线斜率发生改变这一实验现象. 同时, 计算结果表明, 对于双极性半导体的M-S曲线, 利用其直线部分的斜率、直线与电位坐标轴的截距来确定钝化膜的载流子浓度以及平带电位会产生一定的误差.     

Virus-Poly(3,4-ethylenedioxythiophene) Biocomposite Films

Virus-poly(3,4-ethylenedioxythiophene) (virus-PEDOT) biocomposite films are prepared by electropolymerizing 3,4-ethylenedioxythiophene (EDOT) in aqueous electrolytes containing 12 mM LiClO(4) and the bacteriophage M13. The concentration of virus in these solutions, [virus](soln), is varied from 3 to 15 nM. A quartz crystal microbalance is used to directly measure the total mass of the biocomposite film during its electrodeposition. In combination with a measurement of the electrodeposition charge, the mass of the virus incorporated into the film is calculated. These data show that the concentration of the M13 within the electropolymerized film, [virus](film), increases linearly with [virus](soln). The incorporation of virus particles into the PEDOT film from solution is efficient, resulting in a concentration ratio of [virus](film):[virus](soln) ≈ 450. Virus incorporation into the PEDOT causes roughening of the film topography that is observed using scanning electron microscopy and atomic force microscopy (AFM). The electrical conductivity of the virus-PEDOT film, measured perpendicular to the plane of the film using conductive tip AFM, decreases linearly with virus loading, from 270 μS/cm for pure PEDOT films to 50 μS/cm for films containing 100 μM virus. The presence on the virus surface of displayed affinity peptides did not significantly influence the efficiency of incorporation into virus-PEDOT biocomposite films.