Stacking and simultaneous determination of estrogens in water samples by CE with electrochemical detection

A rapid and sensitive method based on transient ITP and field enhancement in CE with electrochemical detection at copper disk electrode was developed for the simultaneous separation and determination of three estrogens: estrone, 17β‐estradiol, and estriol. The effects of several important factors that influence the separation and detection were investigated. Under the optimum conditions, the estrogens could be separated in 0.06 mol/L sodium hydroxide solution within 14 min. With transient ITP by addition of 0.5% NaCl, a good linear response was obtained for three estrogens from 0.2 to 10 μmol/L, with correlation coefficients higher than 0.9993. The detection limits were 8.9 × 10^?8, 6.7 × 10^?8, and 1.1 × 10^?7 mol/L (S/N = 3) for estriol, 17β‐estradiol, and estrone, respectively. This method was successfully employed to analyze different water samples from waterworks, tap water, fishpond, and river samples with recoveries in the range of 90.8–108.9%, and RSDs < 4.69%. The satisfied results demonstrated that this method was of convenient preparation, high sensitivity, and good repeatability, which could be applied to the rapid determination of environmental water samples.     

Determination of estrogens in wastewater using three-phase hollow fiber-mediated liquid-phase microextraction followed by HPLC

Three-phase hollow fiber-mediated liquid-phase microextraction followed by HPLC was used for the determination of three synthetic estrogens, namely diethylstilbestrol, dienestrol, and hexestrol, in wastewater. Extraction conditions including organic solvent, volume ratio between donor solution and acceptor phase, extraction time, stirring rate, donor phase and acceptor phase were optimized. The target compounds were extracted from a 10 mL aqueous sample at pH 1.5 (donor solution) through a 45 mm in length hollow polypropylene fiber that was immersed in 1-octanol in advance, and then the hollow fiber was filled with 10 microL 0.5 mol/L sodium hydroxide solution (acceptor phase). After a 40 min extraction, the acceptor phase was directly injected into an HPLC system for detection. Under the optimized extraction conditions, a large enrichment factor (more than 300-fold) was achieved for the three estrogens. The determination limit at an S/N of 3 ranged from 0.25 to 0.5 microg/L for the estrogens. The recovery ratio was more than 86% in the determination of these estrogens in wastewater.     

Determination of estrogens in water by HPLC-UV using cloud point extraction

A method based on cloud point extraction was developed to determine four kinds of estrogens: estriol (E3), estradiol (E2), estrone (E1), and progesterone (P) in water by high performance liquid chromatography separation and ultraviolet detection (HPLC-UV). The non-ionic surfactant Triton X-114 was chosen as extractant solvent. The parameters affecting extraction efficiency, such as concentrations of Triton X-114 and Na₂SO₄, equilibration temperature, equilibration time and centrifugation time were evaluated and optimized. Under the optimum conditions, preconcentration factors of 99 for E3, 73 for E2, 152 for E1 and 86 for P were obtained for 10 mL water sample. The detection of limitation was 0.23 ng mL⁻¹ for E3, 0.32 ng mL⁻¹ for E2, 0.25 ng mL⁻¹ for E1 and 5.0 ng mL⁻¹ for P. The proposed method was successfully applied to the determination of trace amount of estrogens in wastewater treatment plant (WWTP) effluent water and exposure water with 10 ng mL⁻¹ E2 for toxicological study in our lab. For the case of WWTP effluent water samples, no estrogen was found. The accuracy of the proposed method was tested by recovery measurements of spiked samples and good recoveries of 81.2-99.5% were obtained.     

Simultaneous determination of non-steroidal anti-inflammatory drugs in river water by gas chromatography-mass spectrometry

The gas chromatography/mass spectrometric assay method was developed for the determination of 13 non‐steroidal anti‐inflammatory drugs (NSAIDs) in river water. Extraction was achieved by a liquid‐phase extraction procedure using methylene chloride. The extract was reacted for 30 min at 80°C based on the formation of methyl ester with 1.0 M HCl in methanol and extraction of the derivative with ethyl acetate, which was then measured by gas chromatography‐mass spectrometry. The limit of quantification of NSAIDs was 1.0–60 ng/L and the calibration curve showed linearity being greater than r=0.997. The method was used to analyze ten river water samples from various regions in Korea. Diclofenac, indoprofen, ketoprofen and loxoprofen were detected at concentration of up to 1.29 μg/L in river water. The developed method may prove valuable for use in the national monitoring project of NSAIDs in surface water.     

Confirmatory analysis of non-steroidal anti-inflammatory drugs in bovine milk by high-performance liquid chromatography with fluorescence detection

HPLC with fluorescence detection is considered for confirmatory analysis of group B veterinary drugs by the European Union legislation. A procedure for confirming the presence of anti-inflammatory non-steroidal drug (NSAID) residues in bovine milk by reversed phase high-performance liquid chromatography with fluorescence detection is herein described. The native fluorescence of nine drugs belonging to different NSAID sub-classes, namely flurbiprofen, carprofen, naproxen, vedaprofen, 5-hydroxy-flunixin, niflumic acid, mefenamic acid, meclofenamic acid and tolfenamic acid, allowed for detection in bovine milk down to 0.25–20.0 μg/kg. Confirmation of the nine NSAIDs is attained by fluorescence detection at characteristic excitation and emission wavelengths. The procedure described is simple and selective. Limits of quantification (LOQs) ranging between 0.25 and 20 μg/kg were measured; satisfactory trueness and within-laboratory reproducibility data were calculated at LOQ spiking levels, apart from 5-hydroxy-flunixin. The procedure developed is used in our laboratory for confirmation of each one of the above mentioned NSAIDs in bovine milk, to support results after HPLC quantitative analysis with UV–vis detection.     

Determination of ten anti-inflammatory drugs in serum by isocratic liquid chromatography

Summary A high performance liquid chromatographic system has been developed for the resolution of ten anti-inflammatory drugs. Isocratic separation was achieved using a Spherisorb 5m ODS column with an eluent consisting of water-orthophosphoric acid to pH 3.2: acetonitrile: methanol (523513). A comparison was made between chloroform/acetonitrile (32) and hexane/ether (11) as solvents for the extraction of these drugs from serum.     

Octanol/water partitioning simulation by RP‐HPLC for structurally diverse acidic drugs: Comparison of three columns in the presence and absence of n‐octanol as the mobile phase additive

The advantageous effect of n‐octanol as a mobile phase additive for lipophilicity assessment of structurally diverse acidic drugs both in the neutral and ionized form was explored. Two RP C₁₈ columns, ABZ⁺ and Aquasil, were used for the determination of logk_w indices, and the results were compared with those previously reported on a base‐deactivated silica column. At pH 2.5, the use of n‐octanol‐saturated buffer as the mobile phase aqueous component led to high‐quality 1:1 correlation between logk_w and logP for the ABZ⁺ column, while inferior statistics were obtained for Aquasil. At physiological pH, the correlations were significantly improved if strongly ionized acidic drugs were treated separately from weakly ionized ones. In the latter case, 1:1 correlations between logD_7.4 and logk_w^oct indices were obtained in the presence of 0.25% n‐octanol. Concerning strongly ionized compounds, adequate correlations were established under the same conditions; however, slopes were significantly lower than unity, while large negative intercepts were obtained. According to the absolute difference (diff = logD_7.4–logk_w) pattern, base‐deactivated silica showed a better performance than ABZ⁺, however, the latter seems more efficient for the lipophilicity assessment of highly lipophilic acidic compounds. Aquasil may be the column of choice if logD_7.4<3 with the limitation, however, that very hydrophilic compounds cannot be measured.     

Counter-flow electrokinetic supercharging for the determination of non-steroidal anti-inflammatory drugs in water samples

Electrokinetic supercharging (EKS) has been used in the last few years as a powerful tool for separation and on-line preconcentration of different types of analytes. We have developed a valuable modification for EKS system, namely counter-flow EKS (CF-EKS) and applied it for the separation and on-line preconcentration of seven non-steroidal anti-inflammatory drugs (NSAIDs) in water samples. In CF-EKS, a hydrodynamic counter-flow is applied during electrokinetic injection of the analytes within the EKS system. This counter-flow minimises the introduction of the sample matrix into the capillary, allowing longer injections to be performed. Careful choice of the optimum counter-flow as well as the optimum injection voltage allowed the sensitivity to be enhanced by 11,800-fold, giving limits of detection (LODs) of 10.7–47.0 ng/L for the selected NSAIDs. The developed method was validated and then applied for the determination of the studied NSAIDs in drinking water as well as wastewater samples from Hobart city.     

Determination of repaglinide in pharmaceutical formulations by HPLC with UV detection.

A simple, precise and rapid RP-HPLC method was developed for the determination of repaglinide in pharmaceutical dosage forms. The method was carried out on a Shim-pack, RP-C18 column using a mixture of methanol: 0.1% v/v triethylamine (pH adjusted to 7 with orthophosphoric acid) and detection was done at 235 nm using nimesulide as internal standard. The linearity range was 0.1 to 0.5 microg/ml. The intra-day and inter-day precision were in the range of 0.48 to 1.01 and 0.15 to 1.15, respectively.     

Determination of estrogens and their metabolites in water using C30 SPE-LC-MS

Triacontyl bonded silica (C(30)) material was applied as solid-phase extraction (SPE) sorbent and an SPE-LC-MS method was established for the determination of eight estrogens and their metabolites in water samples. Compared to commercial C(18) SPE cartridge, the performance of C(30) was evaluated in various important SPE conditions, such as sorbent mass, elution solvent and its volume, loading flow rate, and sample loading volume. The results showed a superior performance of C(30)-C(18) by the shorter treatment time and fewer required elution solvent. In the optimum conditions, the results showed good recoveries (80.5-109.4%), excellent linear relationships (0.02-1 ng/mL, except 2-MeO-E(2)), high precisions (lower than 10.0% RSD for both low and high spiked concentration), and low LODs (1-16 ng/L). Method validation using C(30) packed cartridge was also testified with spiked real water samples, including tap water and river water. Satisfy results demonstrated the feasibility of C(30) SPE to the analysis for real environmental waters.     

Development and validation of an analytical method for detection of estrogens in water

An analytical procedure enabling routine analysis of four environmental estrogens at concentrations below 1 ng L^–1 in estuarine water samples has been developed and validated. The method includes extraction of water samples using solid-phase extraction discs and detection by gas chromatography (GC) with tandem mass spectrometry (MS–MS) in electron-impact (EI) mode. The targeted estrogens included 17- and 17-estradiol (aE2, bE2), estrone (E1), and 17-ethinylestradiol (EE2), all known environmental endocrine disruptors. Method performance characteristics, for example trueness, recovery, calibration, precision, accuracy, limit of quantification (LOQ), and the stability of the compounds are presented for each of the selected estrogens. Application of the procedure to water samples from the Scheldt estuary (Belgium – The Netherlands), a polluted estuary with reported incidences of environmental endocrine disruption, revealed that E1 was detected most frequently at concentrations up to 7 ng L^–1. aE2 was detected once only and concentrations of bE2 and EE2 were below the LOQ.Presented at the 9th FECS Conference on Chemistry and the Environment, Bordeaux, France, 29 August–1 September 2004     

Determination of glutathione in pharmaceuticals and cosmetics by HPLC with UV and fluorescence detection

Summary A selective HPLC determination of reduced glutathione (GSH) in pharmaceutical and cosmetic formulations is described based on prechromatographic derivatization with 4-(6-methylnaphthalen-2-yl)-4-oxo-2-buteneoic acid. The derivatization reaction is rapid under mild reaction conditions (10 min at ambient temperature and pH 7.5) and the excess reagent can be removed by liquid-liquid extraction. The thiol adducts were chromatographed on a C-8 column using 0.05 M triethylammonium phosphate (pH 4.0) — acetonitrile 68∶32 (v/v), as the mobile phase; UV and fluorescence detection (l_em 450 nm, l_exc 300 nm) were both used. The structure of the thiol adducts was confirmed by¹H and¹³C NMR spectra using sodium methanethiolate as thiol nucleophile. This work constitutes part of the thesis for the “Dottorato di ricerche” of Dr. Roberto Gotti.     

Orthogonal array designs for the optimization of liquid-liquid-liquid microextraction of nonsteroidal anti-inflammatory drugs combined with high-performance liquid chromatography-ultraviolet detection

Orthogonal array designs (OADs) were applied for the first time to optimize liquid-liquid-liquid microextraction (LLLME) conditions for the analysis of three nonsteroidal anti-inflammatory drug residues (2-(4-chlorophenoxy)-2-methylpropionic acid, ketoprofen, and naproxen) in wastewater samples. Six relevant factors were investigated: type of organic solvent, composition of donor phase and acceptor phase, stirring speed, extraction time and salt concentration. In the first stage, mixed-level orthogonal array design, an OA16 (4(1) x 2(12)) matrix was employed to study the effect of six factors, by which the effect of each factor was estimated using individual contributions as response functions. Based on the results of the first stage, 1-octanol was chosen as organic solvent for extraction. The other five factors were selected for further optimization using an OA16 (4(5)) matrix and a 4 x 4 table to locate more exact levels for each variable. The relative standard deviations for the reproducibility of optimized LLLME varied from 6.2 to 7.1%. The coefficients of determination for calibration curves were higher than 0.9950. The method detection limits for drugs spiked in ultrapure water were in the range of 0.03-0.3 ng/mL. The final optimized conditions were applied to the analysis of drug residues in three wastewater samples in Singapore.     

Isolation and determination of estrogens in water samples by solid‐phase extraction using molecularly imprinted polymers and HPLC

Advanced SPE with molecularly imprinted polymers (MIP) was used in this study. A noncovalent imprinting approach was applied to separate 17β‐estradiol, estriol, and estrone from water samples. Polymer material was prepared by bulk polymerization with methacrylic acid as a functional monomer, divinylbenzene and ethyleneglycol dimethacrylate as crosslinkers, and acetonitrile, acetonitrile/toluene (3:1, v/v) or isooctane/toluene (1:99, v/v) as a porogen. We also prepared an MIP film on a silica gel surface with methacrylic acid and ethyleneglycol dimethacrylate as monomers and acetonitrile as a solvent. Qualitative and quantitative hormone analyses were carried out by HPLC with various detection techniques, including UV/visible spectroscopic detection (diode array detection) and electrochemical detection (CoulArray). The results of the study indicate that MIP technology is an excellent method for the quality control of estrogens in environmental analyses with a low quantification limit for 17β‐estradiol of around 26 (diode array detection) and 0.25 ng/mL (electrochemical detection). The proposed method was found to be suitable for routine determinations of the analyzed compound in environmental laboratories.     

柱前衍生高效液相色谱法测定啤酒中微量甲醛

甲醛作为消毒剂、工业助剂等已广泛应用于各行各业,也列在食品工业加工助剂推荐名单中[1]。然而,甲醛能引起头痛、恶心,肠胃不舒服、皮肤过敏等反应。美国环保署(EPA)称甲醛可能是致癌诱导物[2]。我国居室内空气中甲醛卫生标准不大于0·08mg/m3,而饮用水和饮料类中甲醛允许含量     

Determination of natural and synthetic estrogens in water by gas chromatography with mass spectrometric detection

A procedure for the determination of six natural and synthetic estrogens (diethylstilbestrol, estrone, 17beta-estradiol, mestranol, 17alpha-ethinylestradiol and estriol) in water samples is described. Samples, up to 2000 ml, were concentrated using Oasis HLB solid-phase extraction cartridges. Analytes were derivatized with N-methyl-N-(trimethylsilyl)trifluoroacetamide and determined by GC-MS or GC-MS-MS. The reactivity of several silylation reagents versus aliphatic and aromatic hydroxyl groups contained in the structure of the selected analytes was evaluated. Influence of parameters such as sample pH, nature of the water samples and derivatization conditions on the performance of the whole analytical procedure was systematically studied. Under optimal conditions, quantification limits between 1 and 3 ng/l were achieved for the determination of the considered estrogens in sewage water.     

Determination of anions in rainwater by capillary electrophoresis with conductivity detection

A routine method for the determination of chloride, nitrate and sulfate anions in rainwater by capillary electrophoresis was developed. The system uses an end-column non-suppressed conductivity detector. Linear calibration plots were generated from 0.050 to 20 mg/l, which is the range generally found in wet depositions. Accuracy and precision were evaluated by analyzing certified standards of simulated rainwater and environmental samples, or by comparing CE results with those obtained by IC, the reference technique for anion analysis in wet deposition. The reproducibility of the method was satisfactory except at the lower and upper limits of the analytical range. Sensitivity lay in the range of few μg/l.     

固相萃取-反相高效液相色谱法测定环境水体中卡马西平

建立了固相萃取-反相高效液相色谱法测定水中痕量卡马西平的方法.以C18固相萃取柱对水样固相萃取,再经Agilent ZORBAX Exlipse XDB-C18色谱柱分离,在紫外检测器上检测.考察了洗脱液、流动相比例的影响.确定洗脱液选用甲醇(17+3)溶液,流动相选择甲醇(11+9)溶液.结果线性关系良好(在0.2～...