Cationic host-guest polymerization of N-vinylcarbazole and vinyl ethers in MCM-41, MCM-48, and nanoporous glasses

The synthesis of poly(vinyl ether)s or polyvinylcarbazole under the conditions of constricted geometry can be achieved by means of cationic host-guest polymerisation of the corresponding monomers in the pores of MCM-41 (pore diameter 3.6 nm), MCM-48 (pore diameter 2.4 nm) and in nanoporous glasses (Gelsil with a pore diameter of 5 nm) with bis(4-methoxyphenyl)methyl chloride (BMCC) or triphenylmethyl chloride as the internal surface initiator. The reaction products are new polymer/ MCM-41, polymer/MCM-48 etc., host-guest hybrid materials. The molecular mass of the enclosed polymer and the degree of loading of the host compounds can be adjusted within certain limits. The molecular dynamics were investigated by using broad-band dielectric spectroscopy. Under the conditions of constricted geometry, molecular fluctuation is observed as well as a secondary beta-relaxation, which is hardly affected (in comparison with the free melt) and which corresponds to the relaxation between structural substates (dynamic glass transition). This process is several orders of magnitude faster in its relaxation rate than in the free melt and thus follows a confinement effect. This is already well known in lower molecular weight systems with constricted geometry.     

Swelling, intercalation, and exfoliation behavior of layered ruthenate derived from layered potassium ruthenate

The intercalation chemistry of a layered protonic ruthenate, H_0.2RuO_2.1·nH₂O, derived from a layered potassium ruthenate was studied in detail. Three phases with different hydration states were isolated, H_0.2RuO_2.1·nH₂O (n=0, 0.5, 0.9), and its reactivity with tetrabutylammonium ions (TBA⁺) was considered. The layered protonic ruthenate mono-hydrate readily reacted with TBA⁺, affording direct intercalation of bulky tetrabutylammonium ions into the interlayer gallery. Fine-tuning the reaction conditions allowed exfoliation of the layered ruthenate into elementary nanosheets and thereby a simplified one-step exfoliation was achieved. Microscopic observation by atomic force microscopy and transmission electron microscopy clearly showed the formation of unilamellar sheets with very high two-dimensional anisotropy, a thickness of only 1.3±0.1 nm. The nanosheets were characterized by two-dimensional crystallites with the oblique cell of a=0.5610(8) nm, b=0.5121(6) nm and γ=109.4(2)° on the basis of in-plane diffraction analysis.     

Postsynthesis vapor-phase functionalization of MCM-48 with hexamethyldisilazane and 3-aminopropyldimethylethoxylsilane for bioseparation applications

MCM-48 was surface modified via vapor-phase reactions with hexamethyldisilazane (CH(3)-MCM-48) and 3-aminopropyldimethylethoxysilane (NH(2)-MCM-48). (29)Si NMR confirmed that the resulting materials contained covalently attached trimethylsilane and 3-aminopropyldimethylsilane moieties, both important functionalities for bioseparation applications. The surface coverage was approximately 1.8 and 0.9 groups per nm(2), respectively. The X-ray diffraction patterns and the narrow pore size distributions obtained from the gas sorption isotherms showed that the modified materials retained the characteristic pore structure of the underlying MCM-48 material. CH(3)-MCM-48 exhibited significantly improved hydrolytic stability over the unmodified MCM-48 under the aqueous conditions tested, whereas NH(2)-MCM-48 appeared to be less stable than the unmodified MCM-48. The decrease in stability is most likely due to the nature of the attachment of the 3-aminopropyldimethylsilane moiety, where the conversion of surface silanol groups is limited by H bonding with the amino end, leading to a 50% lower surface concentration and resulting in an increased likelihood of nucleophilic attack on the silica surface, enhancing the rate of hydrolysis. Hexamethyldisilazane thus appears to be a superior functional group for modifying the MCM-48 surface.     

Structure, hydrophobicity, and hydrothermostability of MCM-41 organo-inorganic mesoporous silicates silylated with dimethoxydimethylsilane and dichloromethylphenylsilane

Changes in the structure, hydrophobicity, and hydrothermal stability of organo-inorganic composite materials based on MCM-41 as a result of silylation with dimethoxydimethylsilane (DMODMS) and dichloromethylphenylsilane (DCMPS) were considered. Based on the data on the competitive adsorption of water and toluene it was shown, using the Weitkamp procedure, that the grafting of organosilyl groups affects the sorption properties of mesoporous materials. Hydrothermal treatment led to considerable changes in the structure and properties of the materials. The thermal stability of MCM-41 composites and changes in their hydrophilicity due to the grafting of DMODMS and DCMPS and hydrothermal treatment were studied by thermogravimetry.     

膨胀剂用量、合成体系pH值和MCM-22（P）的硅／铝比对ITQ-2分子筛合成的影响

考察了膨胀剂的用量、合成体系的pH值和MCM-22(P)的硅/铝比对合成ITQ-2分子筛的影响. 结果表明,同时降低膨胀剂十六烷基三甲基溴化铵和四丙基氢氧化铵的用量,在pH=11.5时 4 h 即可完成对MCM-22(P)的插层膨胀;pH值降低时,可减小由于脱硅对ITQ-2分子筛硅/铝比下降的影响,并且使产物收率大幅度提高. 同时, pH值降低使后续的超声剥离更加容易,且可避免生成MCM-41介孔分子筛杂相. MCM-22(P)的硅/铝比越大,层表面的电荷密度越低,带负电荷的层板和阳离子插层剂之间的静电引力和分子间作用力也就越小,致使插层膨胀和随后的超声剥离越容易.     

Interaction energy and surface reconstruction between sheets of layered silicates

Interactions between two layered silicate sheets, as found in various nanoscale materials, are investigated as a function of sheet separation using molecular dynamics simulation. The model systems are periodic in the xy plane, open in the z direction, and subjected to stepwise separation of the two silicate sheets starting at equilibrium. Computed cleavage energies are 383 mJ /m(2) for K-mica, 133 mJ /m(2) for K-montmorillonite (cation exchange capacity=91), 45 mJ /m(2) for octadecylammonium (C(18))-mica, and 40 mJ /m(2) for C(18)-montmorillonite. These values are in quantitative agreement with experimental data and aid in the molecular-level interpretation. When alkali ions are present at the interface between the silicate sheets, partitioning of the cations between the surfaces is observed at 0.25 nm separation (mica) and 0.30 nm separation (montmorillonite). Originally strong electrostatic attraction between the two silicate sheets is then reduced to 5% (mica) and 15% (montmorillonite). Weaker van der Waals interactions decay within 1.0 nm separation. The total interaction energy between sheets of alkali clay is less than 1 mJ /m(2) after 1.5 nm separation. When C(18) surfactants are present on the surfaces, the organic layer (>0.8 nm) acts as a spacer between the silicate sheets so that positively charged ammonium head groups remain essentially in the same position on the surfaces of the two sheets at any separation. As a result, electrostatic interactions are efficiently shielded and dispersive interactions account for the interfacial energy. The flexibility of the hydrocarbon chains leads to stretching, disorder, and occasional rearrangements of ammonium head groups to neighbor cavities on the silicate surface at medium separation (1.0-2.0 nm). The total interaction energy amounts to less than 1 mJ /m(2) after 3 nm separation.     

Synthesis and physical properties of layered silicates/polyurethane nanocomposites

Samples of polyurethane nanocomposites were synthesized using diphenylmethane diisocyanate, poly(ε‐caprolactone) diol, di(ethylene glycol), and a clay functionalized by hydroxyl groups. The inorganic content in the hybrids was 2 wt %, 4 wt %, and 8 wt %. The X‐ray analysis showed that exfoliation occurred for clay content equal to 2% (w/w), whereas for higher contents, the inorganic phase rearranges in an intercalated structure. FTIR analysis suggested that the degree of hydrogen bonding in the hard segments was greatly reduced because of the amount of silicate layers and their dispersion. The dynamic‐mechanical analysis showed that the presence of clay lamellae extends very much the temperature range before the hard domain transition, causing the loss of mechanical consistency of the samples. It is less than 100 °C for the pure polymer, and increases up to 200 °C for the nanocomposites. The permeability of water vapor decreases linearly with inorganic content up to 4% of inorganic phase, and levels off at higher concentrations. The permeability behavior, at low activities, is largely dominated by the diffusion phenomenon. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2454–2467, 2005     

Effect of organomodified layered silicates on the properties and structure of polytetrafluoroethylene

The physicomechanical and triboengineering properties and the structures of polymer composite materials based on polytetrafluoroethylene and layered silicates are studied. The triboengineering characteristics are substantially improved by the introduction of a small amount of layered silicates (2–5 wt %). It is found that the introduction of organomodified layered silicates leads to a considerable reduction in the friction coefficient, by an order of magnitude, and causes an increase in wear resistance (2000-fold). With the use of X-ray structural analysis and scanning electron microscopy, it is shown that, during friction loading, filler particles are localized on the friction surface, thereby hampering wear of the material.     

Factors and processes influencing the reinforcing effect of layered silicates in polymer nanocomposites

The analysis of the tensile yield stress of a large number polymer/layered silicate composites showed widely differing mechanical properties. The composition dependence of yield stress can be described and evaluated quantitatively by a simple model developed earlier for particulate filled polymers. The comparison of data produced in our laboratory or taken from the literature indicated that several processes may take place during the preparation of the composites and a considerable number of factors influence composite properties. Quite a few of these are often neglected and percentage increase in modulus, strength or other properties is reported in published papers instead. The most important of such effects are changing matrix properties when a functionalized polymer is used to promote adhesion (PE, PP), modification of crystalline structure due to nucleation (PA, PP), plasticization or lubrication (PVC), decreased interaction (PA, PVC, PET, rubbers) or chemical reactions (PVC, PP, PET). Using a few simple assumptions, most of which are supported by previous experience, the extent of exfoliation can be estimated quantitatively in nanocomposites. The analysis of the tensile yield stress of more than 80 composites with various matrices indicated that the extent of exfoliation is very low in most composites; it reaches maximum 10% in the best case, which corresponds to about 10 silicate layers per stack. Although the approach has limitations and several factors were neglected during analysis, this result is in agreement with observations indicating that complete exfoliation rarely can be reached in thermoplastic/clay composites. In order to achieve larger reinforcement, silicates must be exfoliated more perfectly in the future.     

Nanocomposites of NLO chromophore‐modified layered silicates and polypropylene

Intercalation of guest species into layered inorganic solids is a method of producing ordered inorganic–organic assemblies with unique microstructures controlled by host–guest and guest–guest interactions. Smectite clay minerals, such as montmorillonite, having appropriate functional molecules in between the silicate layers are supposed to exhibit a wide range of novel characteristics. Nanocomposite material based on maleic anhydride‐grafted polypropylene and dye‐modified layered silicate was developed. Characteristics of organo‐modified montmorillonite particles and polymer/clay hybrids have been investigated through FTIR, SAXS, DSC, UV measurements, and transmission electron microscopy. The results of the intercalation process, structural characterization, and thermal properties will be discussed in comparison with the intercalation and nanocomposite preparation results. The intercalation was successfully conducted by the ion‐exchange method. It was shown that intercalated dibenzilidene acetone type chromophores exist in the clay galleries in an aggregated form, probably as J‐aggregates. This feature strongly effects on optical and nonlinear optical properties of nanocomposites. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2493–2502, 2005     

Inclusion of aramid chains into the layered silicates through solution intercalation route

Aramid–organoclay nanocomposites were fabricated through solution intercalation technique. Montmorillonite was modified with p-amino benzoic acid in order to have compatibility with the matrix. The effect of clay dispersion and the interaction between clay and polyamide chains on the properties of nanocomposites were investigated using X-ray diffraction (XRD), transmission electron microscopy (TEM), tensile testing of thin films, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and water uptake measurements. Excessive clay dispersion was achieved even on the addition of high proportions of clay. The structural investigations confirmed the formation of delaminated nanostructures at low clay contents and disordered intercalated morphology at higher clay loadings. The tensile behavior and thermal stability significantly amplified while permeability reduced with increasing dispersibility of organoclay in the polyamide matrix.     

Fabrication and gas separation properties of polybenzimidazole (PBI)/nanoporous silicates hybrid membranes

Composites of polybenzimidazole (PBI) with proton-exchanged AMH-3 and swollen AMH-3 were prepared, characterized by electron microscopy and X-ray scattering and tested for hydrogen/carbon dioxide ideal selectivity. Proton-exchanged AMH-3 was prepared under mild conditions by the ion exchange of Sr and Na cations in the original AMH-3 using aqueous solution of dl-histidine. Swollen AMH-3 was prepared by sequential intercalation of dodecylamine following the ion exchange in the presence of dl-histidine. Both silicate materials were introduced into a continuous phase of PBI as a selective phase. Mixed matrix nanocomposite membranes, prepared under certain casting conditions, with only 3 wt% of swollen AMH-3 present substantial increase of hydrogen/carbon dioxide ideal selectivity at 35 °C, i.e., more than by a factor of 2 compared to pure PBI membranes (40 vs. 15). Similar ideal selectivity was observed using higher loadings (e.g., 14%) of proton-exchanged AMH-3 particles suggesting that transport of hydrogen is faster than carbon dioxide in AMH-3-derived silicates. However, the ideal selectivity of mixed matrix membranes approaches that of pure polymer as the operating temperature increases to 100 °C and 200 °C. The composite membranes with AMH-3-derived materials were compared with MCM-22/PBI membranes. Composite membranes incorporating MCM-22 plate-like crystals show no selectivity enhancements possibly due to the presence of larger pores in MCM-22.     

Aggregation and decomposition of a pseudoisocyanine dye in dispersions of layered silicates

The optical properties of reaction systems composed from a pseudoisocyanine (PIC) solution and dispersed layered silicates were studied using visible spectroscopy. Two series of reduced-charge montmorillonites were used as the silicate materials. Each series consisted of eight samples with different layer charges, which were prepared from one parent material. Observed trends were verified with another series of dioctahedral and trioctahedral smectites of different layer charges, structure, and origin. The layer charge density of the silicates significantly affected the aggregation of PIC cations. In addition to the formation of J-aggregates, dye spectral bleaching was also observed. Silicates with very low charge densities induced neither significant aggregation nor spectral bleaching of the dye. The highest levels of PIC J-aggregate formation were found in dispersions of the layered silicates with a medium surface charge. However, reversible spectral bleaching was also observed in some cases. PIC dye cations probably change their conformations during the adsorption process, due to the tension resulting from the large size of the cations and the relatively high charge density at the silicate surface. The bleached dye recovers, at least partially, with the rearrangement and redistribution of the dye cations over the time. In contrast, the presence of silicates with very high charge densities (synthetic taeniolite and fluorohectorite) led to the very fast and irreversible decomposition of the PIC. Perhaps, the tension in adsorbed dye cations, induced by the high charge density at the silicate surface, resulted in significant destabilization and a decomposition reaction of the chromophore.     

Isomerization of cationic azobenzene derivatives in dispersions and films of layered silicates

Photoisomerization reactions of cationic azobenzene dyes in solutions, dispersions, and films of layered silicates were studied by visible (Vis) spectroscopy. The dyes isomerized reversibly from thermodynamically more stable trans-isomers to cis-isomers when irradiated with ultraviolet (UV) light. Observed trends were compared with the optical changes of the dyes that occurred as a consequence of their adsorption at the silicate surface. Small fractions of the dyes are likely to have isomerized during the adsorption process, even without the UV-light irradiation. The aggregation of the dyes was another reaction taking place at the surface of the silicates. The extent of the UV-light-induced isomerization reactions was reduced for the adsorbed dye cations. The reaction proceeded readily for a dye with monovalent cations. However, the photoisomerization was practically negligible in both dispersions and films of layered silicates for a dye with bivalent cations, whereas the isomerization proceeded in solution. This phenomenon was interpreted in terms of the attractive electrostatic forces between the substrate and the dye cations, which hindered the isomerization reaction. The layer charge of silicates affected the orientation of the dye cations as observed by X-ray diffraction (XRD) measurements. However, the choice of silicate did not significantly affect the fundamental aspects and the described basic trends of the UV-light-induced isomerization reaction.     

Nanocomposites of polystyrene-b-polyisoprene copolymer with layered silicates and carbon nanotubes

Nanocomposites of polystyrene-b-polyisoprene (PS-b-PI) copolymer with layered-smectite clays (organically modified montmorillonite) and nanostructured clay-carbon nanotube hybrids were prepared. The diblock copolymer was synthesized by anionic polymerization using high-vacuum techniques and was molecularly characterized by size exclusion chromatography. Carbon nanotubes were developed on clay-supported nickel nanoparticles by the CCVD method. Nanotubes attached on the clay platelets were then chemically modified to create ester groups on their surfaces. PS-b-PI nanocomposites at various polymer to reinforcement loadings were prepared by solution intercalation. The final nanocomposites were characterized by powder X-ray diffraction, FT-IR spectroscopy, thermal analysis, and scanning electron microscopy. The experiments complemented with viscometry measurements reveal the successful incorporation of the reinforcements in the polymer mass.