安全壳中钢衬壳热屈曲问题理论与实验研究(II)--实验部分

钢衬壳热屈曲问题是核工程安全壳设计中的主要问题,但实验研究方面的文章发表得不多.文中以200兆瓦核电站安全壳中钢衬壳为研究对象, 采用局部1:1模型,测得了钢衬壳热屈曲温度和应变载荷, 给出了钢衬壳屈曲和初始后屈曲过程中挠度和温度关系、以及膜应变和温度关系, 实验测得钢衬壳具有局域屈曲的现象, 实验屈曲载荷与理论结果符合较好.     

安全壳中钢衬壳热屈曲问题理论与实验研究（Ⅱ）—实验部分

钢衬壳热屈曲问题是核工程安全壳设计中的主要问题,但实验研究方面的文章发表得不多。文中以２００兆瓦核电站安全壳中钢宙为研究对象,采用局部１：１模型,测得了钢衬壳热屈曲温度和应变载荷,给出了钢衬壳屈曲和初始后屈曲过程中挠度和温度关系。     

安全壳中钢衬壳热屈曲问题理论与实验研究(I)———理论分析部分

钢衬壳热屈曲问题是核工程安全壳设计中的主要问题把铆固之间的钢衬壳视为钢衬板的特殊缺陷形式，利用Ｋｏｉｔｅｒ初始后屈曲理论分析了完善和具有初始缺陷钢衬壳的弹性热后屈曲性态给出了用挠度－温度载荷表示的钢衬壳的后屈曲平衡路径表达式和屈曲临界载荷表达式具体分析了三种钢衬壳模型：四点铆固钢衬壳、四边固支钢衬壳和五点铆固钢衬壳给出了钢衬的初始缺陷、锚钉间距、钢衬厚度等参数对钢衬热屈曲载荷的影响结果对安全壳中钢衬壳的设计有很好的参考价值     

钢衬壳后屈曲问题分析

本文用两种方法分析了核电站预应力混凝土安全壳中的内衬壳（钢衬壳）在温度应力作用下的后屈曲问题。认为钢衬壳模型是钢衬板模型的一种特殊缺陷形式，用Ｋｏｉｔｅｒ初始后屈曲渐近分析理论研究了钢衬壳的后屈曲问题。另外，本文从大挠度偏微分方程出发导出控制钢衬壳后屈曲的带有参数的非线性方程组，且用伪弧长法追踪其后屈曲平衡路径。文中用两种方法分析了四点铆固钢衬壳的后屈曲性态，并进行了比较。     

柱壳在轴向冲击载荷作用下动态塑性屈曲的实验研究

圆柱壳的动态塑性屈曲问题的研究主要是集中在屈曲模态方面，至于屈曲的临介载荷与临介时时间则研究的较少，ＳＨＰＢ用于研究材料在高应变率下动态力学性能已为大家所熟悉，但用于研究结构的动态屈曲则未见报道，本文利用一装置对柱壳的动态塑性屈曲进行了实验研究，测出了壳体屈曲过程的载荷，轴向缩短量与时间的关系曲线，得到屈曲时的临介载荷与临介时间，同时发现壳体屈曲变形的一些规律并与静态实验的结果进行了比较，为理论分     

圆柱形薄壳冲击扭转屈曲的实验研究

本文对受冲击扭矩作用下的圆柱形簿壳扭转屈曲进行了实验研究，利用Ｈｏｐｋｉｎｓｏｎ扭杆使圆柱受阶跃扭矩作用，分析所得到的应变－时间曲线，得到了不同几何参数的圆柱壳的冲击临界扭矩Ｍｄｅｒ和屈曲波数ｎ及几条定性结论，同时找出了圆柱壳静力扭转屈曲行为和冲击扭转屈曲行为之间的异同。     

关于结构限制失稳的研究进展

限制失稳是指构件失稳时其屈曲变形不能自由发展而受到某种限制性约束的失稳,有时又称单向失稳、接触失稳、约束失稳.这类问题在工业中有大量应用,也是固体力学中的一个经典问题.最常见的实例如应用于地下管道、隧道、压力容器、核反应堆安全壳中的薄衬壳,当薄衬壳发生屈曲时,由于受到外壁的约束,其屈曲行为和一般的壳体屈曲行为不同,这就需要我们发展新的研究方法.另外如受钻井套管横向约束的钻柱的屈曲,复合材料的分层屈曲,电子元器件中的镀层屈曲等也属于限制失稳的范畴.限制失稳问题因其涉及接触问题、单向屈曲、非保守问题等而显得十分复杂,一直没有得到很好的解决.从近年来文献看,限制失稳的研究多集中在压杆、圆环的研究,板、壳的研究相对较少.本文首先简单介绍了限制失稳的一般概念,指出存在的限制约束对结构屈曲特性的影响.然后分别介绍了对于杆、环、板、壳的受限制失稳的研究进展.最后提出了需要进一步深入研究的问题.图11参75      

轴向冲击载荷下圆柱壳的弹塑性屈曲分析

研究时变轴向冲击载荷作用下的圆柱壳弹塑性动力屈曲问题。本构关系采用增量理论 ,借助增量数值计算方法对Karman Donnell运动方程进行求解。计算表明 :基于B R准则的屈曲判断方法和采用Southwell方法可以获得一致的临界屈曲载荷 ;分别讨论了应力波对屈曲的影响以及材料参数、几何参数、载荷峰值与持续时间和动力屈曲的关系。     

轴向冲击圆柱壳非弹性响应

简要论述承受轴向冲击载荷圆柱壳非弹性动屈曲响应的研究进展。采用Ｋａｒｍａｎ－Ｄｏｎｎｅｌｌ运动方程研究轴向流固冲击载荷作用下的圆柱壳轴对称弹塑性动屈曲问题。本构关系采用增量理论，借助增量数值方法求解动力方程组。研究不同边界条件对屈曲的影响，以及径向外压力在不同边界条件下对屈曲的影响。     

复杂结构热屈曲有限元分析

实现了机械载荷和温度载荷共同作用下复杂结构的弹性分歧热屈曲有限元分析，计算结果表明，局部温度场将使结构的屈曲强度大幅度降低。复杂结构的热屈曲研究具有理论和实际意义。本文研究成果表明，从计算结构力学角度出发，探讨强热源作用复杂结构引起宏观破坏机理研究的可行性。     

ANALYSIS ON BUCKLING AND POSTBUCKLING OF DELAMINATION IN 3D COMPOSITES

In this paper, the problem of axisymmetric buckling and postbuckling of a circular thin-film delamination bridged by through-thickness fiber tows in 3D composites is presented. An iterativeprocedure based on Taylor's series expansion is used to generate a family of nondimensionalized post-buckling solutions of the above problem by yon Karman's nonlinear plate theory. Attention is fo-cused, herein, on the effects of the bridge force of through-thickness fibers on the buckling and post-buckling behavior of the delamination. It is found that fiber bridge not only increases the ability of re-sisting delamination buckling and postbuckling, but also brings on the jump of the delamination deflec-tion mode during the postbuckling phase. Consequently the behavior of the composite structure with de-lamination is greatly improved, such as increasing the residual strength and prolonging the service life.     

Creep buckling and postbuckling of circular cylindrical shells under axial compression

An infinitely long, axially compressed, circular cylindrical shell with an imperfection in the shape of the axisymmetric classical buckling mode, undergoing steady or non-steady creep, is analyzed. The axisymmetric problem is solved incrementally using nonlinear shell equations The ratio of the applied stress to the classical buckling stress determines if the shell will collapse axisymmetrically or if it will bifurcate into a nonaxisymmetric mode, and whether or not bifurcation will result in instantaneous collapse. The bifurcation problem is formulated exactly and the initial postbuckling behavior is investigated via an asymptotic elastic analysis, based on Koiter's general theory Numerical results are compared with available experimental data.     

剪切变形对FGM圆板轴对称屈曲的影响

基于一阶剪切变形板理论，推导了功能梯度材料圆形板在边界面内均布压力作用下的轴对称屈曲方程。在推导过程中，忽略了前屈曲耦合变形。利用一阶板理论与经典板理论屈曲方程之间在数学形式上的相似性，得到了一阶板理论下功能梯度材料圆板与经典板理论下均匀圆板临界屈曲载荷之间的解析关系。利用这个解析关系，可以直接从已有的较为简单的经典理论的结果，获得一阶板理论下功能梯度材料板的临界屈曲载荷。     

Non-linear in-plane postbuckling of arches with rotational end restraints under uniform radial loading

This paper presents a thorough and comprehensive investigation of non-linear buckling and postbuckling analyses of pin-ended shallow circular arches subjected to a uniform radial load and which have equal elastic rotational end-restraints. The differential equations of equilibrium for non-linear buckling and postbuckling are established based on a virtual work approach. Exact solutions for the non-linear bifurcation, limit point and lowest buckling loads are obtained; in particular, exact solutions for the non-linear postbuckling equilibrium paths are derived. The criteria for switching between fundamental buckling and postbuckling modes are developed in terms of critical values of a geometric parameter for an arch, with exact solutions for these critical values of geometric parameter being obtained. Analytical solutions of non-linear buckling and postbuckling problems for arches with rotational end-restraints are of great interest, since they constitute one of the very few closed-form analyses of buckling and postbuckling behaviour of continuous structural systems. These exact solutions are a contribution to the non-linear structural mechanics of arches, as well as providing useful benchmark solutions for verifying non-linear numerical analyses.     

功能梯度与均匀圆板静动态解之间的相似转换关系

基于经典板理论,研究了功能梯度材料圆板的轴对称弯曲、屈曲和自由振动解与相应的均匀材料圆板解之间的转换关系.通过消去拉-弯耦合项得到了以挠度函数表示的功能梯度圆板的弯曲、屈曲和自由振动控制方程.分析功能梯度圆板与均匀圆板的控制方程之间的相似性,得到了功能梯度材料圆板与均匀圆板的解之间解的相似转换关系,在假定FGM圆板的材料性质沿厚分别以幂函数和指数函数的度变规律后,给出了相应的转换系数的解析表达式.该系数集中反映了功能梯度圆板的材料非均匀性.在已知均匀材料圆板轴对称解的条件下,可将功能梯度材料圆板轴对称问题的求解转化为相似转换系数的计算问题.这一方法可为非均匀板的求解提供了十分便捷有效的途径,而且便于工程应用.     

Axisymmetric buckling of transversely isotropic circular and annular plates

This paper presents a general solution of the three-dimensional governing equations for the axisymmetric buckling problem of transversely isotropic media. The solution is expressed by a displacement function that satisfies a homogeneous fourth-order partial differential equation. Using this general solution, the axisymmetric buckling of circular and annular plates is investigated and exact solutions are obtained for appropriate boundary conditions. Numerical results are considered for clamped and simply supported circular and annular plates in comparison with existent results.     

Asymmetric bifurcations in a pressurised circular thin plate under initial tension

It has been known for some time that under certain circumstances the axisymmetric solution describing the deformation experienced by a stretched circular thin plate or membrane under sufficiently strong normal pressure does not represent an energy-minimum configuration. By using the method of adjacent equilibrium a set of coordinate-free bifurcation equations is derived here by adopting the Föppl–von Kármán plate theory. A particular class of asymmetric bifurcation solutions is then investigated by reduction to a system of ordinary differential equations with variable coefficients. The localised character of the eigenmodes is confirmed numerically and we also look briefly at the role played by the background tension on this phenomenon.     

Non-linear in-plane buckling of rotationally restrained shallow arches under a central concentrated load

This paper investigates the non-linear in-plane buckling of pin-ended shallow circular arches with elastic end rotational restraints under a central concentrated load. A virtual work method is used to establish both the non-linear equilibrium equations and the buckling equilibrium equations. Analytical solutions for the non-linear in-plane symmetric snap-through and antisymmetric bifurcation buckling loads are obtained. It is found that the effects of the stiffness of the end rotational restraints on the buckling loads, and on the buckling and postbuckling behaviour of arches, are significant. The buckling loads increase with an increase of the stiffness of the rotational restraints. The values of the arch slenderness that delineate its snap-through and bifurcation buckling modes, and that define the conditions of buckling and of no buckling for the arch, increase with an increase of the stiffness of the rotational end restraints.     

具脱层的正交铺设圆柱壳的初始后屈曲分析

基于非线性弹性理论,建立了含脱层正交铺设圆柱壳的后屈曲控制方程,应用Koiter初始后屈曲理论和小参数摄动法,导出了系统的一阶和二阶摄动控制方程,以及相应的边界条件、位移连续条件和力平衡条件,然后逐阶求解．算例中,讨论了不同脱层深度和长度对脱层复合材料圆柱壳屈曲和初始后屈曲特性的影响,并与已有文献进行了比较．     

Buckling and postbuckling of a compressed thin film bonded on a soft elastic layer: a three-dimensional analysis

The wrinkling of a stiff thin film bonded on a soft elastic layer and subjected to an applied or residual compressive stress is investigated in the present paper. A three-dimensional theoretical model is presented to predict the buckling and postbuckling behavior of the film. We obtained the analytical solutions for the critical buckling condition and the postbuckling morphology of the film. The effects of the thicknesses and elastic properties of the film and the soft layer on the characteristic wrinkling wavelength are examined. It is found that the critical wrinkling condition of the thin film is sensitive to the compressibility and thickness of the soft layer, and its wrinkling amplitude depends on the magnitude of the applied or residual in-plane stress. The bonding condition between the soft layer and the rigid substrate has a considerable influence on the buckling of the thin film, and the relative sliding at the interface tends to destabilize the system.