Headspace stir bar sorptive extraction followed by thermal desorption and gas chromatography with mass spectrometry to determine musk fragrances in sludge samples without sample pretreatment

A direct, simple and solvent‐free method based on headspace stir bar sorptive extraction and thermal desorption gas chromatography with mass spectroscopy was developed to determine 13 musk fragrances (six polycyclic musks, three nitro musks and four macrocyclic musks) in sludge without sample treatment. The optimal headspace stir bar sorptive extraction conditions were achieved when a polydimethylsiloxane stir bar was exposed for 45 min in the headspace of a 10 mL vial filled with 100 mg of sludge mixed with 0.2 mL of water stirred at 750 rpm at 80°C. The stir bar was then desorbed in the thermal desorption gas chromatography and mass spectrometry system, obtaining limits of detection between 5 and 30 ng/g. The method applicability was tested with sewage sludge from two urban wastewater treatment plants and from a potable water treatment plant. Results showed galaxolide and tonalide to be the most abundant musk fragrances found in wastewater treatment plants with maximal concentrations of 9240 and 7500 ng/g, respectively. Maximum concentration levels between 35 and 635 ng/g were found for musk ketone, musk moskene, traseolide, phantolide and celestolide in this kind of samples. Concentrations below the limits of quantitation of phantolide, galaxolide, tonalide and musk ketone were found in sludge from a potable water treatment plant.     

Study of the photoinduced degradation of polycyclic musk compounds by solid-phase microextraction and gas chromatography/mass spectrometry

Polycyclic musks are widely used synthetic fragrances that have been identified during the last few years in biota samples and environmental matrices. Nevertheless, there is a lack of information concerning the photodegradation behavior of these compounds. In this work, the photoinduced degradation of six polycyclic musk compounds (Cashmeran, Celestolide, Phantolide, Galaxolide, Traseolide and Tonalide) was studied using a solid-phase microextraction (SPME) fiber as support. Musk fragrances were extracted from aqueous solutions using SPME fibers that were subsequently exposed to ultraviolet (UV) irradiation for different times. To study the degradation kinetics and to tentatively identify the photoproducts generated, gas chromatography coupled to ion trap mass spectrometry was used. Aqueous photodegradation studies were also performed. The on-fiber photodegradation approach avoids the need for further extraction processes and makes the identification of photoproducts easier, due to their higher concentration on the fibers. All musk compounds were easily photodegraded, suggesting that UV irradiation could work as a decontamination tool for these musks.     

Optimization of a sensitive method for the determination of nitro musk fragrances in waters by solid-phase microextraction and gas chromatography with micro electron capture detection using factorial experimental design

A solid-phase microextraction method (SPME) followed by gas chromatography with micro electron capture detection for determining trace levels of nitro musk fragrances in residual waters was optimized. Four nitro musks, musk xylene, musk moskene, musk tibetene and musk ketone, were selected for the optimization of the method. Factors affecting the extraction process were studied using a multivariate approach. Two extraction modes (direct SPME and headspace SPME) were tried at different extraction temperatures using two fiber coatings [Carboxen–polydimethylsiloxane (CAR/PDMS) and polydimethylsiloxane–divinylbenzene (PDMS/DVB)] selected among five commercial tested fibers. Sample agitation and the salting-out effect were also factors studied. The main effects and interactions between the factors were studied for all the target compounds. An extraction temperature of 100 °C and sampling the headspace over the sample, using either CAR/PDMS or PDMS/DVB as fiber coatings, were found to be the experimental conditions that led to a more effective extraction. High sensitivity, with detection limits in the low nanogram per liter range, and good linearity and repeatability were achieved for all nitro musks. Since the method proposed performed well for real samples, it was applied to different water samples, including wastewater and sewage, in which some of the target compounds (musk xylene and musk ketone) were detected and quantified. Figure Stardardized Pareto charts for the main effects and interactions     

Determination of musk fragrances in sewage sludge by pressurized liquid extraction coupled to automated ionic liquid‐based headspace single‐drop microextraction followed by GC‐MS/MS

A method for the quantitative determination of ten musk fragrances extensively used in personal care products from sewage sludge was developed by using a pressurized liquid extraction (PLE) followed by an automated ionic liquid‐based headspace single‐drop microextraction and gas chromatography‐tandem mass spectrometry. The influence of main factors on the efficiency of PLE was studied. For all musks, the highest recovery values were achieved using 1 g of pretreated sewage sludge, H₂O/methanol (1:1) as an extraction solvent, a temperature of 80°C, a pressure of 1500 psi, an extraction time of 5 min, 2 cycles, a 100% flush volume, a purge time of 120 s, and 1 g Florisil as in‐cell clean‐up extraction sorbent. The use and optimization of an in‐cell clean‐up sorbent was necessary to remove fatty interferents of the PLE extract that make the subsequent ionic liquid‐based headspace single‐drop microextraction difficult. Validation parameters, namely LODs and LOQs, ranged from 0.5–1.5 to 2.5–5 ng/g, respectively. Good levels of intra‐ and interday repeatabilities were obtained analyzing sewage sludge samples spiked at 10 ng/g (n = 3, RSDs < 10%). The method applicability was tested with sewage sludge from different wastewater treatment plants. The analysis revealed the presence of all the polycyclic musks studied at concentrations higher than the LOQs, ranging from 6 to 530 ng/g. However, the nitro musk concentrations were below the LOQs or, in the case of musk xylene, was not detected.     

Analytical methods for the determination of persistent ingredients of personal care products in environmental matrices

Concern about the environmental fate and potential effects of synthetic organic chemicals used in soaps, lotions, toothpaste, and other personal care products continues to increase. This review describes procedures used for the analysis of five classes of these compounds–synthetic musk fragrances, antimicrobials, ultraviolet filters, insect repellents, and parabens–in water, sediment, sewage sludge, air, and aquatic biota. The primary focus is on sample extraction and preparation methods for these compounds. Instrumental methods commonly used for these compounds are also discussed. Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.     

Determination of musk compounds in sewage treatment plant sludge samples by solid-phase microextraction

Headspace solid-phase microextraction, followed by GC-MS analysis is presented as a suitable technique for the determination of musk compounds in sewage treatment plant sludge. Five polycyclic musks (celestolide, phantolide, traseolide, galaxolide and tonalide) and four nitro musks (musk xylene, musk moskene, musk tibetene and musk ketone) were considered in the optimisation of the analytical method. The influence of extraction temperature, fibre coating, agitation, pH and salting out on the efficiency of the extraction along with the extraction kinetics were studied. An extraction temperature of 100 degrees C and sampling the headspace over the stirred sludge sample using polydimethylsiloxane -divinylbenzene as fibre coating lead to effective extraction. The method proposed is very simple and yields high sensitivity, good linearity and repeatability for all the analytes with limits of detection at the sub-ng/g level. The total analysis time, including extraction and GC analysis, was only 40 min, and no manipulation of the sample was required.     

Development of a method based on sorbent trapping followed by solid-phase microextraction for the determination of synthetic musks in indoor air

Synthetic musks are extensively used as fragrance components in a wide range of consumer and personal care products such as detergents, shampoos, perfumes and other cosmetic products. Amongst them, galaxolide and tonalide have become ubiquitous pollutants due to their continuous releasing into the environment. Because of their nature as artificial fragrances, inhalation should be considered as an important exposure pathway, especially in indoor environments. However, up to now very few studies have been carried out to determine these emergent pollutants indoors. In this work, a simple and highly sensitive methodology for the analysis of synthetic musk fragrances in indoor air samples is presented. The proposed methodology combines solid-phase extraction (SPE) and solid-phase microextraction (SPME), followed by gas chromatography-mass spectrometry (GC/MS). To the best of our knowledge, this is the first method based on SPME for the analysis of musks in air. By active sampling, musks present in air were adsorbed onto 25mg Tenax and then transferred to a SPME fiber in the headspace mode (HS). An experimental design strategy was used to optimize main factors potentially affecting the microextraction process such as fiber coating, temperature and the addition of a microvolume of organic solvent to the solid sorbent prior to SPME. Breakthrough of the SPE sorbent was studied from 1 to 10m(3) without significant losses. Recovery studies were performed at two concentration levels (2 and 20ngm(-3)), obtaining quantitative recoveries (>/=85%) by external calibration. A comprehensive study was performed in order to estimate the limits of detection taking into account the contamination risks and laboratory blanks. Values at the sub ngm(-3) level were achieved for all the target compounds sampling 5m(3) air. External calibration, not requiring the complete sampling process, demonstrated to be suitable for the quantification of all musk compounds. Finally, several indoor environments were analyzed using the proposed method.     

Determination of pharmaceuticals, iodinated contrast media and musk fragrances in sludge by LC/tandem MS and GC/MS

Analytical methods have been developed that allow for the determination of antiphlogistics, lipid regulators, the antiepileptic carbamazepine, cytostatic agents, the psychiatric drug diazepam and iodinated contrast media (ICM) as well as two major polycyclic musk fragrances HHCB (galaxolide) and AHTN (tonalide) in activated and digested sludge. The procedures consist of ultrasonic solvent extraction (USE) using methanol/acetone or pressurized liquid extraction (PLE) using 100% methanol. Clean-up was performed with C18ec material and silica gel followed by LC tandem MS (electrospray or atmospheric pressure chemical ionization) detection for pharmaceuticals and iodinated contrast media as well as GC/MS in the SIM mode for musk fragrances. Absolute recoveries from spiked activated sludge in general ranged from 88+/-4 to 119+/-20% for ICM and were 78+/-15 and 87+/-10% for the AHTN and HHCB, respectively. For the pharmaceuticals, absolute recoveries in activated sludge ranged between 43 and 78%. Subsequently, compensation of losses was carried out by using surrogate standards (acidic pharmaceuticals: fenoprop, neutral pharmaceuticals: dihydro-carbamazepine, musk fragrances: AHTN-D3). With one exception the recoveries were also adequate in digested sludge ranging from 43% to 120%.     

Dispersive Micro Solid‐phase Extraction Coupled with Ultrasound‐assisted Solvent Desorption for Determination of Synthetic Polycyclic and Nitro‐aromatic Musks in Aqueous Samples

An optimized method for the determination of five synthetic polycyclic: celestolide (ADBI), phantolide (AHMI), traseolide (ATII), galaxolide (HHCB), tonalide (AHTN), and two nitro‐aromatic musks: musk xylene (MX) and musk ketone (MK), in water samples is described. The method involves a dispersive micro solid‐phase extraction (D‐μ‐SPE) plus ultrasound‐assisted solvent desorption (UASD) prior to their determination by gas chromatography‐mass spectrometry (GC‐MS) using the selected ion storage (SIS) mode. Factors affecting the extraction efficiency of the target analytes from water samples and ultrasound‐assisted solvent desorption were optimized by a Box‐Behnken design method. The optimal extraction conditions involved immersing 10.1 mg of a typical octadecyl (C18) bonded silica adsorbent (i.e., ENVI‐18) in a 50 mL water sample. After 10.4 min of extraction by vigorously shaking, the adsorbent was collected and dried on a filter, and the target musks were desorbed by ultrasound‐assisted for 38 sec with n‐hexane (200 μL) as the desorption solvent. A 10 μL aliquot was then directly determined by large‐volume injection GC‐MS. The limits of quantitation (LOQs) were 1.2 to 5 ng/L. The precision for these analytes, as indicated by relative standard deviations (RSDs), were less than 11% for both intra‐ and inter‐day analysis. Accuracy, expressed as the mean extraction recovery, was between 74% and 92%. A preliminary analysis of the effluents from municipal wastewater treatment plants (MWTP) and river water samples revealed that HHCB and AHTN were the two most commonly detected synthetic musks; their concentration were determined to range from 88 to 690 ng/L for effluent samples, and 5 to 320 ng/L for river water samples. This is a simple, low cost, effective, and eco‐friendly analytical method.     

Determination of synthetic musk compounds in indoor house dust by gas chromatography–ion trap mass spectrometry

A new method for the simultaneous determination of 11 synthetic musks and one fragrance compound in house dust was developed. The nitro musks included musk ketone (MK, 4-tert-butyl-3,5-dinitro-2,6-dimethylacetophenone), musk xylene (MX, 1-tert-butyl-3,5-dimethyl-2,4,6-trinitrobenzene), musk ambrette (1-tert-butyl-2-methoxy-4-methyl-3,5-dinitrobenzene) and musk moskene (1,1,3,3,5-pentamethyl-4,6-dinitroindane). The polycyclic musk compounds were 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethylcyclopenta-(γ)-2-benzopyran (HHCB), 7-acetyl-1,1,3,4,4,6-hexamethyl-1,2,3,4-tetrahydronaphthalene (AHTN), 4-acetyl-1,1-dimethyl-6-tert-butylindane, 6-acetyl-1,1,2,3,3,5-hexamethylindane, 5-acetyl-1,1,2,6-tetramethyl-3-isopropylindane, 6,7-dihydro-1,1,2,3,3-pentamethyl-4(5H)-indanon. The one macrocyclic musk was 1,4-dioxacycloheptadecane-5,17-dione. The bicyclic hydrocarbon fragrance compound (1,2,3,4,5,6,7,8-octahydro-2,3,8,8-tetramethylnaphthalen-2yl)ethan-1-one (OTNE) and HHCB-lactone (4,6,6,7,8,8-hexamethyl-1H,3H,4H,6H,7H, 8H-indeno[5,6-c]pyran-1-one), a degradation product of HHCB, were also analysed. NIST SRM 2781 (domestic sludge) and SRM 2585 (organic contaminants in house dust) were analysed for these target compounds. The method was applied for the analysis of 49 paired samples collected using two vacuum sampling methods: a sample of fresh or "active" dust (FD) collected using a Pullman-Holt vacuum sampler, and a household dust (HD) sample taken from the participants' vacuum cleaners. Method detection limits and recoveries ranged from 12 to 48?ng/g and 54 to 117?%, respectively. AHTN, HHCB, OTNE and HHCB-lactone were detected in all samples, with median concentrations of 552, 676, 252 and 453?ng/g for FD samples, respectively; and 405, 992, 212 and 492?ng/g for HD samples, respectively. MX and MK were detected with high frequencies but with much lower concentrations. The two sampling methods produced comparable results for the target analytes. Widely scattered concentration levels were observed for target analytes from this set of 49 house dust samples, suggesting a wide variability in Canadian household exposure to synthetic musks.     

Optimisation of a solid-phase microextraction method for synthetic musk compounds in water

A solid-phase microextraction method (SPME) for determining trace levels of synthetic musk fragrances in residual waters has been developed. Six polycyclic musks (cashmeran, phantolide, celestolide, traseolide, galaxolide and tonalide), and a macrocyclic musk (ambrettolide) have been analysed. A detailed study of the different parameters affecting the extraction process is presented. The main important factors affecting the microextraction process have been studied and optimised by means of a categorical factorial design. Two extraction modes (direct SPME and headspace SPME) were tried at different extraction temperatures using four different fiber coatings [polydimethylsiloxane (PDMS), Carboxen (CAR)-PDMS, PDMS-divinylbenzene (DVB) and Carbowax (CW)-DVB]. An extraction temperature of 100 degrees C sampling the headspace over the sample using CAR-PDMS or PDMS-DVB as fiber coatings were found to be the experimental conditions that lead to a more effective extraction. The method proposed is very simple and yields high sensitivity, with detection limits in the low pg/ml, good linearity and repeatability for all the target compounds. The total analysis time, including extraction and GC analysis, was only 45 min. The optimised method performed well when it was applied to waste water from an urban treatment plant.     

Determination of synthetic musks in the sediment of the Taihu lake by using accelerated solvent extraction (ASE) and GC/MS

Synthetic musks, substitutes for natural musks, are widely distributed in environment. They have been detected in water, sludge, fish, shrimp, mussels and other aquatic animals, and even in human's adipose tissue, blood and breast milk. In this study, a new extraction procedure, based on the accelerated solvent extraction (ASE) and in cell clean-up technique was developed and successfully coupled with gas chromatography-mass spectrometry (GC/MS) for the analysis of musks in sediment samples. With this method, the limits of detection as low as 0.03–0.05?ng?g^?1 and the recovery rate of 86.0%–104% are achieved. When compared with soxhlet extraction (SE) and ultrasonic extraction (USE), ASE not only has the best extraction efficiency but also has advantage in extraction time and solvent consumption. Eight synthetic musks, including six polycyclic musks (Tonalide (AHTN), Galaxolide (HHCB), Phantolide (AHDI), Traseolide (ATII), Cashmeran (DPMI) and Celestolide (ADBI)) and two nitro musks (musk xylene (MX) and musk ketone (MK)), were evaluated in sediment samples collected from 15 selected locations of the Taihu lake, one of the largest freshwater lakes in China. The contents of synthetic musks in sediment samples range from 0.336 to 3.10?ng?g^?1 for HHCB, 0.184 to 1.21?ng?g^?1 for AHTN, below detection limit (BDL) to 0.349?ng?g^?1 for MX, and BDL to 0.0786?ng?g^?1 for MK. The contents of DPMI, ADBI, AHMI and ATII are below detection limit in all samples. The results reflect current status of fragrance compound pollution in this area, and provide basic data for environmental policy making.     

New analytical method for the determination of musks in personal care products by Quick,Easy, Cheap,Effective, Rugged,and Safe extraction followed by GC–MS

Synthetic musks are organic compounds used as fragrance additives and fixative compounds in a diversity of personal care products. A new method based on quick, easy, cheap, effective, rugged, and safe (QuEChERS) extraction followed by GC–MS for the analysis of 12 musks in personal care products was developed and validated. Some experimental parameters, such as total QuEChERS mass, sample mass/solvent volume ratio, type of extraction solvent, as well as salts and sorbents amount were investigated and optimized. The final method involves the musks extraction using acetonitrile, followed by the addition of anhydrous magnesium sulphate and sodium acetate. The clean‐up step was performed using dispersive SPE with primary and secondary amine and octadecyl–silica sorbents. This extraction procedure is fast (about 10 min) when compared to other traditional approaches. The method was robust for the matrices studied and shows a high precision (%RSD < 15%) and accuracy (average recovery of 85%), allowing the detection of musks in minimum concentrations between 0.01 ng/g (galaxolide) and 15.80 ng/g (musk xylene). The developed method was applied to the analysis of 12 samples, which revealed musks concentrations ranging from 2 ng/g (toothpaste) to 882 340 ng/g (perfumed body lotion).     

人工合成麝香的分析方法及环境污染现状

人工合成麝香作为天然麝香的替代物被大量用于日化产品中,按其化学结构可分为硝基麝香、多环麝香和大环麝香3种。人工合成麝香的大量生产及广泛使用使之通过各种途径进入环境,而该物质亲脂性和持久性的特点,导致其在生物体内积累并产生毒理效应,故引起了广泛关注,成为一类新型污染物。该文综述了目前人工合成麝香的分类、环境污染现状及不同基体样品的分析检测方法,为今后合成麝香的风险评价研究提供参考。     

Synthetic musk fragrances in environmental Standard Reference Materials

Synthetic musk fragrances have been measured in water, air, sediments, sewage sludge, and biota worldwide. As the study of the environmental fate and impacts of these compounds progresses, the need for Standard Reference Materials (SRMs) for these compounds to facilitate analytical method improvement and interlaboratory comparisons becomes increasingly important. The National Institute of Standards and Technology (NIST) issues environmental matrix SRMs with certified concentrations for a variety of persistent organic pollutants including polycyclic aromatic hydrocarbons (PAHs), chlorinated pesticides, and polychlorinated biphenyl congeners (PCBs). Until now synthetic musk fragrance concentrations have not been reported in NIST SRMs. The objective of this study was to provide reference values for several commonly detected synthetic musk fragrances in several NIST natural matrix SRMs. In this study five polycyclic musk fragrances [HHCB (1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethylcyclopenta-γ-2-benzopyran), AHTN (7-acetyl-1,1,3,4,4,6-hexamethyl-1,2,3,4-tetrahydronaphthalene), ADBI (4-acetyl-1,1-dimethyl-6-tert-butylindane), AHMI (6-acetyl-1,1,2,3,3,5-hexamethylindane), and ATII (5-acetyl-1,1,2,6-tetramethyl-3-isopropylindane] and two nitro musk fragrances [musk xylene (1-tert-butyl-3,5-dimethyl-2,4,6-trinitrobenzene) and musk ketone (4-tert-butyl-3,5-dinitro-2,6-dimethylacetophenone)] were measured in selected environmental SRMs. Gas chromatography–electron impact mass spectrometry (GC/EI-MS) was used for all analyses. HHCB was the most frequently detected synthetic musk fragrance and was detected in SRM 2585 Organic Contaminants in House Dust, SRM 2781 Domestic Sludge, SRM 1974b Organics in Mussel Tissue (Mytilus edulis), and SRM 1947 Lake Michigan Fish Tissue. It was not detected in SRM 1946 Lake Superior Fish Tissue or SRM 1945 Organics in Whale Blubber. Concentrations of HHCB in these SRMs ranged from 1.12 ng/g in SRM 1947 to 92,901 ng/g in SRM 2781. All of the polycyclic musk fragrances were detected in SRM 2781 and all of the target compounds were detected in SRM 2585. Electronic supplementary material Supplementary material is available for this article at and is accessible to authorized users.     

An analytical multi-residue approach for the determination of semi-volatile organic pollutants in pine needles

Vegetation (and pine needles in particular) has been widely used as an alternative to other conventional sampling devices to assess the atmospheric presence of semi-volatile organic contaminants (SVOCs). While most analytical procedures developed focus only on one or two chemical classes, this this work intends to establish a multi-component protocol to quantify brominated flame-retardants (BFRs), polychlorinated biphenyls (PCBs), organochlorine pesticides (OCPs), polynuclear aromatic hydrocarbons (PAHs) and one class of contaminant of emerging concern, the synthetic musks fragrances (SMCs). Pine needles extracts were obtained by ultrasonic solvents extraction (USE), and different cleanup approaches using solid-phase extraction (SPE) employing combinations of sorbents and solvents as well as gel permeation chromatography (GPC) were tested. SPE with alumina followed by GCP yielded the best results, with average recoveries over 80%.     

Determination of synthetic musk fragrances

Among personal care products (PCPs), musks fragrances are a chemically heterogeneous group sharing some sensory characteristics, specially related with odour aspects that have received great attention in the last decade. From a chemical point of view, synthetic musks can be divided in four groups including nitrobenzene derivatives, polycyclic and macrocyclic musks (MCMs) and alicyclic derivatives. Thus, analytically, it is necessary to apply chromatography coupled to mass spectrometry (mainly GC-MS) for the determination of musk residues with adequate sensitivity and selectivity. This review gives a critical overview of published methods for the determination of synthetic musks in different environmental and biological matrices. Methodological aspects considering the different sample preparation and instrumental parameters involved have been reviewed and summarised paying special attention to method validation results. Although GC-MS-based methods are the most abundant ones, the use of tandem MS has become an interesting alternative to improve both sensitivity and selectivity.     

Stir-bar-sorptive extraction and liquid desorption combined with large-volume injection gas chromatography–mass spectrometry for ultra-trace analysis of musk compounds in environmental water matrices

Stir-bar-sorptive extraction with liquid desorption followed by large-volume injection and capillary gas chromatography coupled to mass spectrometry in selected ion monitoring acquisition mode (SBSE–LD/LVI-GC–MS(SIM)) has been developed to monitor ultra-traces of four musks (celestolide (ADBI), galaxolide (HHCB), tonalide (AHTN) and musk ketone (MK)) in environmental water matrices. Instrumental calibration (LVI-GC–MS(SIM)) and experimental conditions that could affect the SBSE-LD efficiency are discussed. Assays performed on 30-mL water samples spiked at 200 ng L^?1 under optimized experimental conditions yielded recoveries ranging from 83.7?±?8.1% (MK) to 107.6?±?10.8% (HHCB). Furthermore, the experimental data were in very good agreement with predicted theoretical equilibria described by octanol–water partition coefficients (K _PDMS/W?≈?K _O/W). The methodology also showed excellent linear dynamic ranges for the four musks studied, with correlation coefficients higher than 0.9961, limits of detection and quantification between 12 and 19 ng L^?1 and between 41 and 62 ng L^?1, respectively, and suitable precision (< 20%). Application of this method for analysis of the musks in real water matrices such as tap, river, sea, and urban wastewater samples resulted in convenient selectivity, high sensitivity and accuracy using the standard addition methodology. The proposed method (SBSE–LD/LVI-GC–MS(SIM)) was shown to be feasible and sensitive, with a low-sample volume requirement, for determination of musk compounds in environmental water matrices at the ultra-trace level, overcoming several disadvantages presented by other sample-preparation techniques.     

Semi-automated disk-type solid-phase extraction method for polychlorinated dibenzo-p-dioxins and dibenzofurans in aqueous samples and its application to natural water

A disk-type solid-phase extraction (SPE) method was used for the extraction of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in natural water and tap water. Since this SPE system comprised airtight glass covers with a decompression pump, it enabled continuous extraction with semi-automation. The disk-type SPE method was validated by comparing its recovery rates of spiked internal standards with those of the liquid-liquid extraction (LLE). The recovery ranges of both methods were similar in terms of (13)C-labeled internal standards: 64.3-99.2% for the LLE and 52.4-93.6% for the SPE. For the native spike of 1,3,6,8-tetrachlorinated dibenzo-p-dioxin (TCDD) and octachlorinated dibenzo-p-dioxin (OCDD), the recoveries in the SPE were in the normal range of 77.9-101.1%. However, in the LLE, the recoveries of 1,3,6,8-TCDD decreased significantly. One of the reasons for the low recovery is that the solubility of this congener is high. The semi-automated SPE method was applied to the analysis of different types of water: river water, snow, sea water, raw water for drinking purposes, and tap water. PCDD/F congeners were found in some sea water and snow samples, while their concentrations in the other samples were below the limits of detection (LODs). This SPE system is appropriate for the routine analysis of water samples below 50L.     

Comprehensive characterization of rodenticides in wastewater by liquid chromatography-tandem mass spectrometry

Rodenticides are used as pest control to eradicate rodents and have emerged as new environmental contaminants due to their widespread use in domestic and urban infrastructures. In this study, we have developed and validated an analytical methodology based on liquid chromatography-tandem mass spectrometry (LC-MS/MS) for the determination of 13 anticoagulant rodenticides in wastewater. In a first step, ionization conditions were tested in electrospray mode, and positive ionization gave the highest sensitivity. Fragmentation patterns were determined and two selected reaction monitoring (SRM) transitions were selected for each compound. Using a Zorbax Eclipse XDB-C18 column and specific SRM transitions, 13 compounds were resolved. The LC-MS/MS method provided good linearity, sensitivity, intra- and inter-day precision, and good identification capabilities for these compounds in wastewaters. Thereafter miniaturized liquid–liquid extraction (LLE) and solid-phase extraction (SPE) were optimized. Oasis HLB and Strata WA SPE cartridges with methanol/dichloromethane as eluting solvents provided good recoveries and limits of detection ranged between 0.34 and 20 ng L^?1, whereas LLE failed to recover some compounds. Finally, the performance of both LLE and SPE methods was evaluated by analyzing rodenticides in a set of wastewaters. Warfarin was the only detected compound at nanogram per liter level, and good agreement was observed between LLE and SPE.