A 90° mixed-mode twisted nematic liquid-crystal-on-silicon with an insulating protrusion structure

A 90°mixed-mode twisted nematic liquid-crystal-on-silicon(90°-MTN LCoS) with protrusion located between the adjacent pixels is proposed to reduce the effect of fringing field. The influence of the protrusion with different widths from0.5 μm to 0.9 μm and different heights from 0.3 μm to 0.7 μm is investigated. The results demonstrate that the invalid pixel region width can be reduced by 31.5% via using the protrusion with the suitable width and height compared with no protrusion case, which provides a higher display quality, such as the higher reflectance and contrast ratio.     

Experimental investigation on laser flattening of sheet metal

The purpose of this research is to establish the technique of laser flattening and to consider the fundamental mechanism. The thermal stress produced by heating with a laser beam is used to make a flat sheet from a sheet metal of protruded distortion. Three kinds of protrusions are chosen as the typical protruded distortion; point protrusion, line protrusion and face protrusion. For point protrusion, laser irradiation along the circular path is effective when the height of protrusion is large, and the laser irradiation along the radial path is effective when it is small. For line protrusion, laser beam is irradiated along the short straight path whose direction is normal to the centerline of the protrusion. For face protrusion, the height decreases from 1-0.1 mm by the laser irradiation along the circular path. The residual stress at the convex surface of a point protrusion on the sheet metal changes from a large compressive stress to a small tensile stress by the laser irradiation.     

Fabrication of a Near-Field Optical Fiber Probe with a Nanometric Metallized Protrusion

We have developed a novel probe with a nanometric metallized protrusion extending through a subwavelength aperture to increase optical near-field excitation and collection efficiencies. The apex diameter of the fabricated metallized protrusion was 35 nm. The Intensity distribution of the optical near-field at the apex of the probe was measured by scanning another probe across the apex, and it was observed that strong optical near-field was generated at the apex of the metallized protrusion. The width of the intensity distribution was 150 nm including instrumental resolution. Probes with spherical and ellipsoidal metallized protrusion were also fabricated, by which enhancement of the optical near-field is expected due to localized plasmon excitation.     

一种针对激光诱导击穿光谱技术的基线校正方法

针对激光诱导击穿光谱(laser-induced breakdown spectroscopy,LIBS)数据中存在的周期性拱形突起问题,提出了一种改进的基线校正算法。该算法基于惩罚最小二乘方法,通过改变局部惩罚系数,使其在拟合周期性拱形突起的同时降低谱线强度对拟合基线的影响。与其他基线校正方法相比,该算法在拟合仿真基线时的均方根误差更小,并且基于该算法得到光谱数据绘制的定标曲线的相关系数达到了0.997 2。结果表明：该算法相较于现有的去基线方法,在拟合中阶梯光栅光谱仪采集激光诱导击穿光谱的基线时,能更好地保留光谱数据的有效信息。     

Protrusion of a Virtual Model Lamellipodium by Actin Polymerization: A Coarse-Grained Langevin Dynamics Model

We report the development of a coarse-grained Langevin dynamics model of a lamellipodium featuring growing F-actin filaments in order to study the effect of stiffness of the F-actin filament, the G-actin monomer concentration, and the number of polymerization sites on lamellipodium protrusion. The virtual lamellipodium is modeled as a low-aspect-ratio doubly capped cylinder formed by triangulated particles on its surface. It is assumed that F-actin filaments are firmly attached to a lamellipodium surface where polymerization sites are located, and actin polymerization takes place by connecting a G-actin particle to a polymerization site and to the first particle of a growing F-actin filament. It is found that there is an optimal number of polymerization sites for rapid lamellipodium protrusion. The maximum speed of lamellipodium protrusion is related to competition between the number of polymerization sites and the number of available G-actin particles, and the degree of pulling and holding of the lamellipodium surface by non-polymerizing actin filaments. The lamellipodium protrusion by actin polymerization displays saltatory motion exhibiting pseudo-thermal equilibrium: the lamellipodium speed distribution is Maxwellian in two dimensions but the lamellipodium motion is biased so that the lamellipodium speed in the direction of the lamellipodium motion is much larger than that normal to the lamellipodium motion.     

Temporal measures of anticipatory labial coarticulation for the vowel/u/: within- and cross-subject variability.

The timing of upper lip protrusion movements and accompanying acoustic events was examined for multiple repetitions of word pairs such as "lee coot" and "leaked coot" by four speakers of American English. The duration of the intervocalic consonant string was manipulated by using various combinations of /s/, /t/, /k/, /h/, and /#/. Pairwise comparisons were made of consonant string duration (acoustic /i/ offset to acoustic /u/ onset) with durations of: protrusion movement beginning to acoustic /u/ onset, maximum acceleration of the movement to acoustic /u/ onset, and acoustic /u/ onset to movement end. There were some consonant-specific protrusion effects, primarily on the movement beginning event for /s/. Inferences from measures of the maximum acceleration and movement end events for the non-/s/ subset suggested the simultaneous and variable expression of three competing constraints: (1) end the protrusion movement during the voiced part of the /u/; (2) use a preferred movement duration; and (3) begin the /u/-related protrusion movement when permitted by relaxation of the perceptually motivated constraint that the preceding /i/ be unrounded. The subjects differed in the degree of expression of each constraint, but the results generally indicate that anticipatory coarticulation of lip protrusion is influenced both by acoustic-phonetic context dependencies and dynamical properties of movements. Because of the extensive variation in the data and the small number of subjects, these ideas are tentative; additional work is needed to explore them further.     

飞机外露物隐身改进设计研究

外露物在一定程度上影响飞机隐身性能,而外露物的共形设计会增加成本。针对低成本准隐身飞机,本文探讨了一种外露物的隐身改进设计,主要采取优化外形,涂敷吸波材料、提升加工工艺等措施实现低成本飞机RCS值的缩减。经过隐身仿真、隐身测试等手段,获取了外露物在不同频点、不同极化下的RCS值,并通过仿真、测试数据对比验证采取隐身改进措施的有效性,并为其它外露物隐身设计提供了设计依据和手段。     

Flattening of sheet metal by laser forming

Laser forming is a thermal process for deformation of sheet metal by thermal stress. In this paper, the technique of laser forming is applied to flatten a protruded distortion on the sheet metal, and the mechanism of flattening is investigated experimentally. The protrusion of some height is intentionally produced by pressing a steel ball on a flat sheet metal. The laser beam was irradiated at the area of distortion, and as a result, the protrusion disappeared and an almost flat sheet metal could be obtained.     

Flattening property of a surface due to optical assisted chemical near-field etching

A mechanism of surface flattening is proposed based on our original mathematical model of surface development by introducing a protrusion-selective etching process which has been demonstrated by the optical near-field assisted chemical etching of glass substrate. We study various mechanisms of surface development due to etching processes depending on the local curvature of substrate and explain that the nature of optical near-field showing the stronger field–matter coupling and associated field enhancement near a sharper protrusion is essential for the flattening property.     

Some observations on the appearance of instability of a plane charged liquid surface

A dispersion relation is obtained for the capillary oscillations of a hemispherical protrusion (oblate or prolate) on the plane surface of a conducting liquid in a uniform electrostatic field parallel to the symmetry axis of the protrusion. For the fundamental mode of the capillary oscillations realized on the protrusion the critical dependence of the parameter characterizing its stability in an external electrostatic field is obtained as a function of the square of the eccentricity as the protrusion is drawn out from the an oblate to a prolate hemisphere. Such a change in shape lowers the threshold electric field for instability of the protrusion. Zh. Tekh. Fiz. 69, 15–22 (July 1999)     

High resolution images of Mo2C(0001)- structure by scanning tunneling microscopy

A C-terminated structure on Mo₂C(0001) was observed by scanning tunneling microscopy. The structure was observed as a honeycomb structure with dark depressions corresponding to C atoms which make up the lattice. High resolution imaging was possible at low tunneling resistance less than 1 MΩ. Each C atom appears as a shallow sombrero protrusion predicted by theoretical calculations of C atoms on a metal substrates. It is concluded that the C atoms occupied threefold hollow sites of the (1×1) Mo layer of the substrate and a model for the structure is proposed.     

Optimal frequency-response sensitivity of compressible flow over roughness elements*

Compressible flow over a flat plate with two localised and well-separated roughness elements is analysed by global frequency-response analysis. This analysis reveals a sustained feedback loop consisting of a convectively unstable shear-layer instability, triggered at the upstream roughness, and an upstream-propagating acoustic wave, originating at the downstream roughness and regenerating the shear-layer instability at the upstream protrusion. A typical multi-peaked frequency response is recovered from the numerical simulations. In addition, the optimal forcing and response clearly extract the components of this feedback loop and isolate flow regions of pronounced sensitivity and amplification. An efficient parametric-sensitivity framework is introduced and applied to the reference case which shows that first-order increases in Reynolds number and roughness height act destabilising on the flow, while changes in Mach number or roughness separation cause corresponding shifts in the peak frequencies. This information is gained with negligible effort beyond the reference case and can easily be applied to more complex flows.     

Experimental studies of bubble dynamics inside a corner

The dynamics of a bubble near a corner formed by two flat rigid boundaries (walls), is studied experimentally using a spark-generated bubble. The expansion, collapse, rebound, re-collapse and migration of the bubble, along with jetting and protrusion, are captured using a high-speed camera. Our experimental observations reveal the behaviour of the bubble in terms of the corner angle and the dimensionless standoff distances to the near and far walls in terms of the maximum bubble radius. The bubble remains approximately spherical during expansion except for its surface becoming flattened when in close proximity to a wall. When a bubble is initiated at the bisector of the two walls, the bubble becomes oblate along the bisector during the late stages of collapse. A jet forms towards the end of collapse, pointing to the corner. The closer the bubble to the two walls, the more oblate along the bisector the bubble becomes, and the wider the jet. A bubble initiated near one of the two walls is mainly influenced by the nearer wall. The jet formed is pointing to the near wall but inclined towards the corner. After the jet penetrates through the bubble surface, the bubble becomes a bubble ring, and a bubble protrusion forms following the jet. The bubble ring collapses and subsequently disappears, while the protrusion firstly expands, and then collapses and migrates to the corner.     

Surface-plasmon vortices in nanostructured metallic films

Light scattering by a small protrusion on a metal surface is analyzed within the framework of perturbation theory. Upon normal incidence of a linearly polarized monochromatic wave, slight deviations of the protrusion’s shape from a circularly symmetric one lead to the formation of optical vortices in the near-field region due to resonant excitation of circular surface plasmons. This agrees with the results of scanning near-field optical microscopy experiments revealing distinct spiral patterns in the in-plane near-field intensity distribution for metallized nanostructured polymer substrates.     

InAs Quantum Dots On (001) GaAs Substrate with two Groups of Different Sizes Under Arsenic Shutter Closed Condition

The effect of temperature on the self-assembled InAs quantum dots (QDs) grown on GaAs substrate under arsenic shutter closed condition has been studied. From atomic force microscopy (AFM), it was found that the size of InAs dots exhibited a transition from single-sized uniformly distributed quantum dot (QD) at a growth temperature of 490°C to two groups of different sizes QDs at 510°C. Since the desorption rate of In atoms from the substrate surface is very high at 510°C, a growth model is proposed that attributes the larger sized QDs to the enhanced capture of desorbed In atoms by a local random protrusion which initiates a regenerative capture and growth process and leads to explosive growth.     

Dynamic range and linearity improvement for zero-field single-beam atomic magnetometer

Zero-field single-beam atomic magnetometers with transverse parametric modulation for ultra-weak magnetic field detection have attracted widespread attention recently. In this study, we present a comprehensive response model and propose a modification method of conventional first harmonic response by introducing the second harmonic correction. The proposed modification method gives improvement in dynamic range and reduction of linearity error. Additionally, our modification method shows suppression of response instability caused by optical intensity and frequency fluctuations. An atomic magnetometer with single-beam configuration is built to compare the performance between our proposed method and the conventional method. The results indicate that our method's magnetic field response signal achieves a 5-fold expansion of dynamic range from 2 nT to 10 nT, with the linearity error decreased from 5% to 1%. Under the fluctuations of 5% for optical intensity and ±15 GHz detuning of frequency, the proposed modification method maintains intensity-related instability less than 1% and frequency-related instability less than 8% while the conventional method suffers 15% and 38%, respectively. Our method is promising for future high-sensitive and long-term stable optically pumped atomic sensors.     

Femtosecond laser pulse irradiation of Sb-rich AgInSbTe films: Scanning electron microscopy and atomic force microscopy investigations

The single-layer and multilayer Sb-rich AgInSbTe films were irradiated by a single femtosecond laser pulse with the duration of 120 fs. The morphological feature resulting from the laser irradiation have been investigated by scanning electron microscopy and atom force microscopy. For the single-layer film, the center of the irradiated spot is a dark depression and the border is a bright protrusion; however, for the multilayer film, the center morphology changes from a depression to a protrusion as the energy increases. The crystallization threshold fluence of the single-layer and the multilayer films is 46.36 mJ/cm², 63.74 mJ/cm², respectively. PACS 79.20.Ds; 78.55.Qr; 78.66.Jg; 68.37.Ef; 68.37.Ps     

具有穿插界面结构的高效绿光有机电致磷光器件

以传统有机电致磷光器件ITO/NPB/CBP∶Ir(ppy)₃/BAlq/Alq₃/LiF/Al为研究对象,在NPB/CBP∶Ir(ppy)₃、CBP∶Ir(ppy)₃/BAlq及BAlq/Alq₃界面处构造交互穿插结构。器件的光电性能测试表明:交互穿插结构一方面能够降低电流密度,减少高电流密度下磷光猝灭中心的形成;另一方面能增加载流子复合界面面积,从而分散界面三线态激子,降低三线态-三线态激子的猝灭。此外,界面凸起的存在还有利于器件的光耦合输出。实验结果表明:当穿插厚度为10 nm,器件的最大电流效率达到34.0 cd/A,与传统器件的电流效率18.7 cd/A相比,提高了55%。     

Memristive operations demonstrated by gap-type atomic switches

We demonstrate memristive operations using gap-type Ag₂S atomic switches, in which the growth and shrinkage of an Ag protrusion are controlled by using solid-electrochemical reactions. In addition to conventional memristive operations such as those proposed and demonstrated by resistive random-access memories (ReRAMs) using metal oxide compounds, gap-type Ag₂S atomic switches also show new types of memristive operations by storing information from input signals without changing their output until a sufficient number of signals are inputted. The new types of memristive operations resemble the learning process seen in neuroplasticity, where changes occur in the organization of the human brain as a result of experience.