Cz结构浅池内硅熔体热对流的分岔特性

为了了解水平温度梯度作用时Czochralski结构浅池内硅熔体热对流的分岔特性,利用有限差分法进行了非稳态三维数值模拟,坩埚外壁被加热,液池深度为3 mm.模拟结果表明,当逐渐增加温差时,会发生两次流型转变,第一次由二维轴对称流动转变为三维稳态流动,第二次由三维稳态流动转变为热流体波,其可能沿顺时针方向旋转、也可能沿逆时针方向旋转,同时,第二次转变存在分岔现象.     

邱克拉斯基结构液池内旋转驱动流动及转变

为了了解旋转对邱克拉斯基(Czochralski)晶体生长结构液池内熔体流动的影响,利用有限差分法进行了三维非稳态数值模拟,坩埚外半径为50 mm,晶体半径为15 mm,液池深度为50 mm。结果表明,当旋转速度较低时,流动为稳态轴对称流动,随着转速的提高,流动会转化为三维非稳态振荡流动;晶体与坩埚同向旋转时,流动转化的临界转速较高,反向旋转时,临界转速较低;晶体单独旋转时,速度波周向速度远小于晶体旋转速度,坩埚单独旋转时,速度波周向速度与坩埚旋转速度保持一致;坩埚转速越快,速度波动幅度和波数越小。     

浮力对环形液池内热毛细对流的影响

为了了解浮力的影响,对水平温度梯度作用时环形液池内的热毛细对流进行了非稳态三维数值模拟,环形液池外壁被加热,半径为40 mm,内壁被冷却,半径为20 mm,液池深度为(1-17)mm,流体为0．65cSt的硅油,其Pτ数为6．7．模拟结果表明,当水平温度梯度较小时,流动为轴对称稳态流动,随着温度梯度的增加,流动将会失去其稳定性,在浅液池内,转化为热流体波,浮力对失稳后的流型无影响,但会使热流体波的振幅下降;在深液池内,在常重力条件下,转化成三维稳定流动,在微重力和小重力条件下,转化为三维振荡流动．     

深径比对邱克拉斯基结构内旋转驱动流动的影响

为了了解深径比对邱克拉斯基(Czochralski)结构内旋转驱动流动的影响,利用有限容积法进行了三维非稳态数值模拟。结果表明:随着液池深径比的增加,流动逐渐加强,当旋转速度超过某一临界值后,流动转变为三维非稳态振荡流动。随着液池深径比的增加,速度波振荡幅度增大,速度波波数和周向传播方向都随之改变;浅液池内坩埚旋转作用占主导地位,速度波传播方向与坩埚旋转方向相同,深液池内晶体旋转大于坩埚旋转对流动的影响,速度波传播方向和晶体旋转方向相同。     

毛细力比对环形液池内耦合热-溶质对流的影响

为了了解毛细力比R_σ对耦合热溶质毛细对流的影响,对深宽比为0.15的环形浅液池内双组分溶液耦合热-溶质毛细对流进行了三维数值模拟。液池内、外壁分别维持恒定温度和浓度,工质为甲苯/正己烷混合溶液,Prandtl数为5.54,Lewis数为25.8。结果表明,当热毛细Reynolds(ReT)数较小时,耦合热-溶质毛细对流为三维稳态流动,当ReT数超过临界值后,流动将转变为三维周期性振荡流动;在计算范围内(-1≤R_σ≤0),随着毛细力比的增加,流动失稳的临界Re_T数会逐渐减小。     

环形浅液池内热毛细对流的热力学特性

为了了解径向温度梯度作用下环形浅液池内硅熔体热毛细对流的热力学特性,利用有限差分法进行了非稳态三维数值模拟。液池外半径r0=50 mm,内半径ri=15 mm,深度为d=3 mm。结果表明,当温度梯度较小时,流动为稳定轴对称流动,系统总熵产较小;随着温度梯度的增加,流动将失去其稳定性,首先转化为径向脉动波,此时系统总熵产呈周期性变化;温度梯度再增加时,流动转化为热流体波,系统总熵产较大,但不再随时间变化。     

环形浅液池内中等Pr数流体的热毛细对流

为了了解微重力下水平温度梯度作用时环形浅液池内的热毛细对流特性,利用有限差分法进行了非稳态二维数值模拟,环形液池外壁被加热,内壁被冷却,流体为 0.65 cSt的硅油,其Pr 数为 6.7。结果表明,当温度梯度较小时,流动为稳态流动,随着温度梯度的增加,流动将会失去其稳定性,转化成各种振荡流动,模拟结果与实验结果基本吻合。     

水平温差对环形浅液池内Marangoni-热毛细对流的影响

双向温差驱动下的Marangoni-热毛细对流在许多工程技术领域具有重要作用, 但是, 已有的大部分研究集中于单向温差作用下的流动. 因此, 采用数值模拟的方法研究了水平温差对双向温差驱动下的环形浅液池内Marangoni-热毛细对流的影响. 在一个给定的顶部换热条件下, 确定了不同水平温差作用下流动由轴对称稳态流动向三维非稳态流动转变的临界底部热流密度. 结果表明, 水平温差使得Marangoni-热毛细对流不稳定; 随着水平温差的持续增强, 稳态流动转变为一种规律的振荡流动, 最终变得混乱; 发现两种新的状态演化过程; 确定了水平温差和垂直温差在共同驱动流体运动时各自发挥的作用; 随着水平温差的增强, 最初出现在中间区域的最高表面温度不断向热壁移动, 在此过程中, 内壁附近的流动增强, 而外壁附近的流动减弱.     

重力水平对热毛细-浮力对流耗散结构的影响

为了了解重力水平对环形液池内热毛细-浮力对流耗散结构的影响,利用有限容积法进行了非稳态三维数值模拟,环形液池外壁被加热,内壁被冷却,流体为0．65cSt硅油,其Pr数为6．7。结果表明,在微重力条件下,流动为三维振荡流动;当重力水平增加到0．1go时,流动结构转化为沿周向运动的一组滚胞,其轴线与温度梯度方向一致;当重力...     

液封液桥内振荡热毛细对流的三维数值模拟

为了了解微重力下液封液桥内热毛细对流的基本特性,利用有限差分法进行了非稳态三维数值模拟,液桥高为(1-3)mm,直径为2mm和3 mm,液封外直径为(4-7)mm。模拟结果表明,当Marangoni数较小时,液封液桥内的热毛细对流为稳定的轴对称运动,当Marangoni数超过某一临界值后,流动将转化为三维振荡流动;为此,确定了发生振荡的临界Marangoni数,分析了各种条件下热毛细对流的振荡特性,计算了相应的振荡频率。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.