Y2O3:C陶瓷的发光性能

采用传统陶瓷制备工艺制备了C掺杂的Y2O3多晶陶瓷;研究了Y2O3:C陶瓷的光谱性能,发现在403 nm有明显的发射峰.通过对其激发光谱的研究,表明它们是由F+和F色心造成的.本文还研究了Y2O3:C 陶瓷的热释光和光释光性能.用2个指数衰变函数拟合光衰变曲线得到的衰变时间常数τ1=(4.66±0.27)s,τ2=(23.31±1.03)s.     

硝酸镁在γ-Al2O3上的热分解及MgO/γ-Al2O3的碱性

研究了不同载量时Mg(NO3)2 在γ Al2O3 上存在状态和热分解行为差异.考察了Mg含量不同时MgO/γ Al2O3 的碱性变化情况 ,并与水滑石焙烧产物Mg(Al)O的碱性进行了对比.结果表明,Mg(NO3)2 可单层分散于γ Al2O3 表面 ,Mg(NO3)2 的分散决定了MgO的分散阈值 ;单层态的Mg(NO3)2 比晶态的分解温度低 ;MgO/γ Al2O3 在阈值附近具有单位表面最高碱量 ,碱位分布与Mg(Al)O相似 ,单位表面碱量高于Mg(Al)O.由于γ Al2O3 的织构可以方便地调节 ,且MgO/γ Al2O3很容易制备 ,MgO/γ Al2O3 是一个很有应用前景的固体碱.     

La2O3对Yb3+掺杂的氧化钇透明激光陶瓷性能的影响

本文研究了La2O3的含量对(Yb0.05 Y0.95)2O3透明激光陶瓷的结构性能和烧结性能的影响.结果表明:随着La2O3含量的增加,拉曼光谱特征峰发生红移,声子能量降低,半高宽增大,相对强度先增大后减小;同时密度、相对密度和透过率都增大,陶瓷的晶粒减小,而当La2O3含量继续增加时,晶粒基本保持不变.但适量的La2O3掺杂量对(Yb0.05Y0.95)2O3透明激光陶瓷的发射性能影响不大.最合适的La2O3添加量为10at%,最合适的烧结温度为1700℃,最后样品的直线透过率可达到75%.     

La2O3对氧化铝透明陶瓷显微结构和透光性能的影响

采用传统无压烧结工艺在氢气氛下制备Al2O3透明陶瓷。实验结果表明：MgO和La2O3复合添加时，随着La2O3掺杂量的增加体积密度总体上保持上升的趋势。随着保温时间的延长，陶瓷的致密化程度增大，残余气孔逐步排出，晶粒进一步长大。采用La2O3和MgO复合添加比单独掺入MgO陶瓷样品透过率更高，掺杂效果更好。在烧结温度为1750℃，保温时问为1h条件下，在波艮为300～800nm测试范围内，陶瓷样品的全透过率大于82％，最大值为86％。     

高温气相合成纳米TiO2-Al2O3复合颗粒的形态

TiO2和 Al2O3复合陶瓷具有热膨胀系数小、熔点高、抗震性好等优良性能,是一种很有发展前途的高温结构材料 [1]。 Woignier等 [2]采用醇盐共水解的 Sol gel法制备 TiO2 Al2O3复合颗粒,原料成本高、反应时间长; Okumura等 [3]利用烷氧基钛的水解反应在 Al2O3颗粒表面包覆 TiO2得到 TiO2 Al2O3复合颗粒,该法均匀性差,且需要液固分离、干燥和煅烧等,干燥和煅烧极易导致颗粒凝并或烧结。 Hung等 [4]利用燃烧法制备 SiO2 GeO2、 TiO2 Al2O3等复合粒子,研究中未采取有效措施控制复合颗粒形貌和大小,也未对颗粒形态结…     

负载型ZrO2催化苯甲醛Meerwein-Ponndorf-Verley反应中的载体效应（英文）

采用浸渍法制备了Si-MCM-41和Al-MCM-41(Si/Al=50)介孔分子筛,SiO2,γ-Al2O3及MgO等负载的ZrO2催化剂,考察了其在以异丙醇为氢源苯甲醛Meerwein-Ponndorf-Verley(MPV)还原反应中的催化活性,并与纯ZrO2的催化活性进行对比.同时,采用X射线衍射、N2吸脱附法、X射线光电子能谱、紫外-可见漫反射光谱和吡啶原位吸附红外光谱等手段表征了催化剂.结果表明,ZrO2负载于Si-MCM-41,Al-MCM-41和SiO2后,催化活性明显提高,这归因于ZrO2与载体间存在强相互作用形成ZrOSi键,使催化剂表面ZrOH数量显著增多,Lewis酸中心强度增强,并出现Brnsted酸中心,三种催化剂的活性高低次序是5%ZrO2/Si-MCM-41>5%ZrO2/Al-MCM-41>5%ZrO2/SiO2.而5%ZrO2/Al2O3和5%ZrO2/MgO基本无催化活性,可归因为ZrO2与γ-Al2O3的弱相互作用使5%ZrO2/Al2O3的酸性与γ-Al2O3类似,ZrO2与MgO的强相互作用使5%ZrO2/MgO基本无酸性.     

MoO3/Al2O3催化氧化选择性合成亚砜

采用浸渍法制备了不同负载量的MoO3/Al2O3催化剂,讨论了MoO3,Al2O3和MoO3/Al2O3负载的催化剂作用下,利用H2O2进行硫醚氧化制亚砜的反应.结果显示MoO3/Al2O3催化剂负载量为20%时催化活性最高,原料转化率达100%,且没有副产物生成.将该方法应用到兰索拉唑前体的氧化反应中,收率达到80%.催化剂重复使用6次不失活.     

焙烧温度对CeO2改性Pd/Al2O3甲醇分解催化剂性能的影响

考察了焙烧温度对Pd/Al2O3和CeO2改性Pd/Al2O3甲醇分解催化剂反应性能的影响.在300℃～700℃范围内焙烧,Pd/Al2O3和Pd/CeO2/Al2O3催化剂的活性都呈现出先升高后降低的趋势.XRD结果表明高温焙烧时活性组分Pd在γ-Al2O3载体表面发生聚集是Pd/Al2O3催化剂活性降低的原因,而XPS结果却表明,Pd在CeO2改性γ-Al2O3载体表面的浓度与Pd/CeO2/Al2O3催化剂的活性变化并非呈现一致关系,TPR表明活性组分Pd和助剂CeO2在γ-Al2O3上产生了一定的相互作用.从而认为Pd的分散度以及Pd和CeO2之间的相互作用共同决定催化剂的甲醇分解性能.     

Y2O3∶C陶瓷的发光性能

采用传统陶瓷制备工艺制备了C掺杂的Y₂O₃多晶陶瓷;研究了Y₂O₃∶C陶瓷的光谱性能,发现在403 nm有明显的发射峰。通过对其激发光谱的研究,表明它们是由F⁺和F色心造成的。本文还研究了Y₂O₃∶C陶瓷的热释光和光释光性能。用2个指数衰变函数拟合光衰变曲线得到的衰变时间常数τ₁=(4.66±0.27)s,τ₂=(23.31±1.03) s。     

XANES研究Al2O3包覆LiNi0.4Co0.2Mn0.4O2材料的稳定性

采用溶胶凝胶水解法在LiNi0.4Co0.2Mn0.4O2(NCM)表面包覆了0.5 wt%Al2O3.透射电镜(TEM)表明在NCM表面形成了均匀的Al2O3包覆层;分别采用恒电位极化及热重分析(TG)研究了包覆前后NCM的析氧特性;采用X射线吸收近边结构谱(XANES)研究了包覆前后O的电子结构.结果表明,包覆后的NCM析氧量更少;Al2O3包覆使得NCM表面层中与金属3d轨道杂化的O比例减少,而更稳定的、与金属4sp轨道杂化的O比例增加.这些因素导致Al2O3包覆后的NCM更加稳定、安全性更高.     

Defect chemistry and VUV optical properties of the BaMgAl10O17:Eu-Ba0.75Al11O17.25:Eu solid solution

The optical properties of the BaMgAl₁₀O₁₇:Eu²⁺ (BAM)-Ba_0.75Al₁₁O_17.25:Eu²⁺ (BAL) solid solution have been studied using VUV excitation, emission and reflectance spectroscopy. Three unique Eu²⁺ emission centers are observed in a ratio that depends on the composition of the host and the dopant concentration. Two of the emission centers are assigned to Eu on normal Beevers-Ross sites and Eu on anti Beevers-Ross sites. The defect chemistry of this system is modeled based on the known behavior of the spinel (MgO·nAl₂O₃) system. Based on this model, the third Eu center can be assigned either to Eu near Al vacancies or to Eu associated with O atoms in the cation layer. In undoped materials exciton emission is observed, peaking at 263 nm in BAM and 285 nm in BAL. This emission may be the mechanism of host-to-activator energy transfer in these phosphors.     

Photoluminescence and energy transfer in Tb/Mn co-doped ZnAl2O4 glass ceramics

We report on Tb³⁺ as efficient sensitizer for red photoemission from Mn²⁺-centers in ZnO-B₂O₃-Al₂O₃-Si₂O-Na₂O-SrO glasses and corresponding gahnite glass ceramics. In comparison to singly or co-doped glasses, the glass ceramics exhibit significantly increased emission intensity. Structural considerations, ESR, and dynamic luminescence spectroscopy indicate partial incorporation of Mn²⁺ as well as Tb³⁺ into the crystalline phase, the former on octahedral Zn²⁺-sites. Interionic distance and charge transfer probability between both species depend on crystallization conditions. This enables control of the energy transfer process and, hence, tunability of the color of photoemission by simultaneous emission from Tb³⁺ and Mn²⁺ centers. Concentration quenching in Mn²⁺-singly doped materials was found at a critical dopant concentration of about 1.0 mol%. The energy transfer process was studied in detail by dynamic as well as static luminescence spectroscopy. Spectroscopic results suggest the application of the studied materials as single or dual-mode emitting phosphor for luminescent lighting.     

Application of TiO2/Er3+:Y3Al5O12 composite to photo-degrade acid red B dye under sun light irradiation

In this work, an upconversion luminescence agent, Er³⁺:Y₃Al₅O₁₂, was synthesized and its absorption and fluorescent spectra was determined. By calculation, the upconversion efficiency of the emission peak at 320 nm was estimated to be about 3.4%. And then, TiO₂/Er³⁺:Y₃Al₅O¹² composite was prepared by simple ultrasonic dispersion and liquids boil methods. The obtained composite was characterized by X-ray diffrac-tion. The effect of TiO₂/Er³⁺:Y₃Al₅O₁₂ composite with different Er³⁺:Y₃Al₅O₁₂ doping amount, heat-treated temperature and heat-treated time on photodegradation of acid red B under sun light was investigated in detail. It was found that the photocatalytic activity of TiO₂/Er³⁺:Y₃Al₅O₁₂ composite was much higher than that for the similar system with only TiO₂ powder. These results support the usefulness of TiO₂/Er³⁺:Y₃Al₅O₁₂ composite in the process of photodegrading dye wastewater and using the sun light.     

Ho3+/Yb3+共掺ZnO-Al2O3-GeO2-SiO2玻璃陶瓷的制备和上转换发光性质

综合ZnO-Al₂O₃-SiO₂系和锗酸盐玻璃陶瓷的优点,采用熔融-晶化法首次制备了Ho³⁺/Yb³⁺共掺以ZnAl₂O₄为主晶相的ZnO-Al₂O₃-GeO₂-SiO₂系玻璃陶瓷。因[GeO₄]四面体和[SiO₄]四面体都是玻璃网络形成体,讨论了GeO₂取代SiO₂对玻璃陶瓷样品硬度及发光性能的影响,最终确定GeO₂的取代量为10.55%（w/w）时,玻璃陶瓷综合性能最佳。在980 nm泵浦光的激发下,发现强的绿色（546 nm）和弱的红色（650 nm）上转换发光,并研究了不同Ho³⁺/Yb³⁺掺杂比对样品上转换发光的影响,最终结果表明当Ho³⁺/Yb³⁺掺杂比为1：11（n/n）时样品荧光强度最强,在绿色上转换发光材料方面具有潜在的应用。     

Eu3+-Tb3+共掺杂SiO2-B2O3-Na2O-Y2O3-P2O5玻璃陶瓷的制备与发光性能

采用高温熔融法制备Eu3+?Tb3+共掺杂SiO2?B2O3?Na2O?Y2O3?P2O5前驱体玻璃。对前驱体玻璃粉末进行差示扫描量热(DSC)分析,确定玻璃陶瓷样品的热处理温度。前驱体玻璃热处理后,采用X射线衍射(XRD)和扫描电镜(SEM)分析可知前驱体玻璃中有Na3.6Y1.8(PO4)3晶粒析出。利用荧光光谱对玻璃陶瓷样品的发光性能进行表征,同时分析了Tb3+离子的荧光衰减曲线,确定Eu3+、Tb3+离子的发光机理以及能量传递过程。通过对Eu3+?Tb3+共掺杂玻璃陶瓷样品的发射光谱采集并用色坐标软件和色温计算程序,获得玻璃陶瓷样品的色坐标和相关色温。     

Crystal structure of Eu-doped M3MgSi2O8 (M: Ba, Sr, Ca) compounds and their emission properties

Emission properties of Eu²⁺-doped M₃MgSi₂O₈ (M: Ba, Sr, Ca) are discussed in terms of the crystal structure. When Ba²⁺ ions account for over one third of M²⁺ ions, M₃MgSi₂O₈ crystallizes in glaserite-type trigonal structure, while Ba-free compounds crystallize in merwinite-type monoclinic structure. Under UV excitation, the Eu²⁺-doped glaserite-type compounds exhibit an intense blue emission assigned to 5d-4f electron transition at about 435 nm, regardless of the molar ratio of Ba²⁺, Sr²⁺ and Ca²⁺ ions. By contrast, the Eu²⁺-doped merwinite-type compounds show an emission color sensitive to the ratio. A detailed analysis of the emission spectra reveals that the emission chromaticity for the Eu²⁺-doped M₃MgSi₂O₈ is composed of two emission peaks reflecting two different sites accommodating M²⁺ ion.     

A bifunctional probe for Al3+ and Zn2+ based on diarylethene with an ethylimidazo[2,1-b]thiazole-6-hydrazide unit

A new diarylethene with ethylimidazo[2,1-b]thiazole-6-hydrazide unit was synthesized, and its photochromic and fluorescent behaviors have been systematically investigated by the stimulation of lights and metal ions in methanol. This new diarylethene exhibited high selectivity and sensitivity toward Al³⁺ and Zn²⁺. The addition of Al³⁺ and Zn²⁺ displayed excellent colorimetric response behaviour with the concomitant color change from colorless to yellow, which could be easily observed by the naked eye. Upon addition of Al³⁺, the fluorescence intensity was enhanced by 180–fold and the emission peak of 1O–Al³⁺ blue-shifted by 15?nm accompanied with a color change from colorless to bright blue. In contrast, when stimulated with Zn²⁺, its fluorescence intensity was enhanced by 35–fold and the emission peak of 1O–Zn²⁺ red-shifted by 16?nm with an evident color change from black to bright green. The LOD for Al³⁺ and Zn²⁺ were determined to be 2.97?×?10^?9?mol?L^?1 and 5.98?×?10^?9?mol?L^?1, respectively. Moreover, a logic circuit was constructed with the fluorescence intensity as the output signal responding to the light and chemical species as the inputs.     

Ho3+/Yb3+共掺ZnO-Al2O3-GeO2-SiO2玻璃陶瓷的制备和上转换发光性质

综合ZnO-Al_2O_3-SiO_2系和锗酸盐玻璃陶瓷的优点,采用熔融-晶化法首次制备了Ho~(3+)/Yb~(3+)共掺以ZnAl_2O_4为主晶相的ZnO-Al_2O_3-GeO_2-SiO_2系玻璃陶瓷。因[GeO_4]四面体和[SiO_4]四面体都是玻璃网络形成体,讨论了GeO_2取代SiO_2对玻璃陶瓷样品硬度及发光性能的影响,最终确定GeO_2的取代量为10.55%(w/w)时,玻璃陶瓷综合性能最佳。在980 nm泵浦光的激发下,发现强的绿色(546 nm)和弱的红色(650 nm)上转换发光,并研究了不同Ho~(3+)/Yb~(3+)掺杂比对样品上转换发光的影响,最终结果表明当Ho~(3+)/Yb~(3+)掺杂比为1∶11(n/n)时样品荧光强度最强,在绿色上转换发光材料方面具有潜在的应用。     

High-pressure transitions in MgAl2O4 and a new high-pressure phase of Mg2Al2O5

Phase transitions in MgAl₂O₄ were examined at 21-27 GPa and 1400-2500 °C using a multianvil apparatus. A mixture of MgO and Al₂O₃ corundum that are high-pressure dissociation products of MgAl₂O₄ spinel combines into calcium-ferrite type MgAl₂O₄ at 26-27 GPa and 1400-2000 °C. At temperature above 2000 °C at pressure below 25.5 GPa, a mixture of Al₂O₃ corundum and a new phase with Mg₂Al₂O₅ composition is stable. The transition boundary between the two fields has a strongly negative pressure-temperature slope. Structure analysis and Rietveld refinement on the basis of the powder X-ray diffraction profile of the Mg₂Al₂O₅ phase indicated that the phase represented a new structure type with orthorhombic symmetry (Pbam), and the lattice parameters were determined as a=9.3710(6) Å, b=12.1952(6) Å, c=2.7916(2) Å, V=319.03(3) Å³, Z=4. The structure consists of edge-sharing and corner-sharing (Mg, Al)O₆ octahedra, and contains chains of edge-sharing octahedra running along the c-axis. A part of Mg atoms are accommodated in six-coordinated trigonal prism sites in tunnels surrounded by the chains of edge-sharing (Mg, Al)O₆ octahedra. The structure is related with that of ludwigite (Mg, Fe²⁺)₂(Fe³⁺, Al)(BO₃)O₂. The molar volume of the Mg₂Al₂O₅ phase is smaller by 0.18% than sum of molar volumes of 2MgO and Al₂O₃ corundum. High-pressure dissociation to the mixture of corundum-type phase and the phase with ludwigite-related structure has been found only in MgAl₂O₄ among various A²⁺B³⁺₂O₄ compounds.     

Charge-transfer type luminescence of Yb3+ ions in LuPO4 and YPO4

Broad band emission which has two peaks at 290 nm and 420 nm was observed in Yb³⁺-activated LuPO₄ and YPO₄. It is shown that this emission is due to a charge-transfer type transition, i.e. the reverse process of the charge-transfer absorption of Yb³⁺ ions.