Mechanical properties of BPDA-ODA polyimide fibers

An aromatic polyimide was synthesized via a one-step polycondensation reaction between biphenyltetracarboxylic dianhydride (BPDA) and 4,4′-oxydianiline (ODA) in p-chlorophenol. The polyimide (BPDA-ODA) solution dopes were spun into fibers by means of dry-jet wet spinning. The as-spun fibers were drawn and treated in heating tubes for improving the mechanical properties. The thermal treatment on the fibers resulted in a relatively high tensile strength and modulus. Thermal mechanical analysis (TMA) was employed to study the linear coefficient of thermal expansion (CTE). Thermal gravimetry analysis (TGA) spectra showed that the BPDA-ODA fibers possessed an excellent property of thermo-oxidative degradation resistance. The sonic modulus E_s of the polyimide fibers was measured.     

聚酰亚胺纤维的研究进展

聚酰亚胺纤维由于分子主链含有刚性的芳杂环结构,赋予其优异的力学、热学、耐辐照、介电以及化学稳定性等性能,从而在航空航天、高温耐热、防火阻燃、电子器件、核能等领域具有广泛应用前景,并成为21世纪最具潜力的高性能纤维之一。近年来,随着单体来源、工艺条件的不断改善,聚酰亚胺纤维的研究得到更大关注和投入,极大促进了聚酰亚胺纤维的规模化制备和应用发展开发。本文综述了近年来高性能聚酰亚胺纤维的国内外研究成果,并针对不同化学结构、纺丝工艺以及亚胺化方法对纤维性能的影响进行阐述,同时也对其发展趋势进行展望。     

Mechanical properties of polyimide/multi-walled carbon nanotube composite fibers

A series of polyimide (PI)/multi-walled carbon nanotube (MWCNT) composite fibers were prepared by copolymerizing a mixture of monomers and carboxylic-functionalized MWCNTs, followed by dry-jet wet spinning, thermal imidization, and hot-drawing process. The content of the carboxylic groups of MWCNTs significantly increased when treated with mixed acid, whereas their length decreased with treatment time. Both the carboxylic content and length of MWCNTs influenced the mechanical properties of the composite fibers. Fiber added with 0.1 wt% MWCNTs treated for 4 h exhibited the best mechanical properties, i.e., 1.4 GPa tensile strength and 14.30% elongation at break, which were 51% and 32% higher than those of pure PI fibers, respectively. These results indicated that a suitable MWCNT content strengthened and toughened the resultant PI composite fibers, simultaneously. Moreover, raising draw ratio resulted in the increase of tensile strength and tensile modulus of the composite fibers.     

热亚胺化过程中气氛和拉力对BPDA-PDA聚酰亚胺纤维结构与性能的影响

研究了3,3',4,4'-联苯四酸二酐-对苯二胺(BPDA-PDA)型聚酰胺酸(PAA)纤维热亚胺化过程中气氛和拉力对聚酰亚胺(PI)纤维结构和性能的影响. 热处理过程中, 恒温处理5 min时, 虽然不同气氛下纤维的表面形貌并无明显差异, 但N₂气下所得纤维的力学性能明显优于空气下的样品, N₂气保护作用下, 最高断裂强度和初始模量分别达到1.25和65.0 GPa. 恒温处理40 min时, N₂气对纤维表面形貌有明显的保护作用. 但对于力学性能, 气氛的影响仅在450 ℃时表现得非常明显. 低于450 ℃时, 长时间的热处理成为影响纤维力学性能的主要因素, 气氛的影响变得不明显. 高于450 ℃时, 在N₂气和空气中的纤维皆发生明显的降解, 从而严重影响其力学性能. 热亚胺化过程中施加的拉力会促进纤维热酰亚胺化过程中的膨胀. 随着拉力的增加PI纤维长度增加, 同时直径减小. PI纤维轴上(004)晶面的间距、 晶粒尺寸、 线性热膨胀系数(为负值)的绝对值及玻璃化转变温度都随热处理时拉力的增加而增大. 纤维的断裂强度随拉力的变化基本保持在0.90 GPa左右, 断裂伸长率随着拉力增加稍有下降, 纤维的初始模量随拉力的增大而增加.     

原位红外光谱法研究电纺聚酰胺酸纳米纤维膜热亚胺化过程

以均苯二酐和二苯醚二胺为原料合成聚酰胺酸溶液,通过静电纺丝法制得聚酰胺酸纳米纤维膜.利用原位红外技术研究亚胺化进程,并以优化的条件制得聚酰亚胺纳米纤维膜.研究结果表明,当升温速率为2℃/min时,在350℃可实现100%亚胺化;升温速率过快,纳米纤维膜的亚胺化程度较低;采用快速-慢速相结合的升温方法,则可以有效地提高亚胺化效率.     

AO-resistant properties of polyimide fibers containing phosphorous groups in main chains

A series of polyimide fibers containing phosphorus element derived from (3-aminophenyl) methyl phosphine oxide (DAMPO) diamine was exposed to an artificial atomic oxygen environment which simulated the space environment in low earth orbit (LEO). The mass loss, surface morphology, chemical composition, and mechanical properties of the fibers before and after atomic oxygen (AO) exposure were compared in detail with a blank sample. Results showed that the phosphor-containing fibers demonstrated lower mass change and less tensile strength reduction. SEM results showed that the fibers with phosphorous element had relatively dense surface after AO exposure. Meanwhile, XPS results indicated that a passivated phosphate layer, which could protect the following under-layer from attacking by AO, was formed on the surface of the fibers. These results indicated that the incorporation of diamine (DAMPO) into the main chains could protect the fibers for avoiding further erosion from AO exposure. Hence, the phosphor-containing PI fibers exhibits potential application in space fields.     

Comparison of four methods for determining fiber content of carbon fiber/epoxy composites

The most fundamental parameter that controls the properties of fiber/epoxy composites is fiber content. Thus, exact calculation of carbon fiber content is important for product quality control and process optimization. In this study, four methods for calculating fiber content of continuous carbon fiber/epoxy composites were investigated. These four methods are processing statistical (PS), optical microscopy (OM), thermogravimetric analysis (TGA), and carbonization-in-nitrogen (CIN). The results show that the CIN and PS methods have high repeatability with no more than 4.7 wt.% deviation, and a relatively exact estimation of fiber content can be obtained by using both of them. A larger difference was generated when the TGA and OM methods were used to determine the fiber content. This is because the small amount of samples required by these methods is not sufficiently representative of the whole carbon fiber composite structure. The PS and CIN methods can be used as approved ways to calculate fiber content of carbon fiber/epoxy composites effectively.     

Surface orientation effect of asymmetric polyimide hollow fibers on their gas transport properties

In this study, we focused on the shear stress effects within a spinneret during hollow fiber spinning on the formation of the hollow fibers and their gas transport properties. We fabricated asymmetric polyimide hollow fibers with a completely defect-free thin skin layer using a dry/wet phase inversion process. The apparent calculated skin layer thickness of the hollow fiber was 280 nm and the O₂ permeance was 2.9×10⁻⁵ cm³ (STP)/(cm² s cmHg). Interestingly, the skin layer thickness was reduced at the high shear rate. In addition, the gas permeances and selectivities of the hollow fibers increased with the increasing shear rate. We concluded that the oriented skin layer of the hollow fiber induced by shear stress had a significant influence on the formation of the skin layer and its gas transport properties. From the ATR-IR spectra results, it was clear that the surface skin layer of the hollow fiber was parallel oriented.     

Influence of temperature and imidization method on the structure and properties of polyimide fibers prepared by wet spinning

A polyamic acid (PAA) based on 4,4′-bis(4-aminophenoxy)diphenyldiamine and 1,3-bis-(3′,4-dicarboxyphenoxy)benzene dianhydride was synthesized. PAA fibers were prepared by wet spinning. Subsequent cyclization of PAA units was achieved using chemical or thermal imidization. The influence of the imidization method and process conditions on the chemical structure, porosity, morphology, thermal and mechanical properties of polyimide (PI) fibers was studied. Thermal imidization was carried out in the temperature range from 60 to 300 °C at different process durations. The degree of imidization of PI fibers was studied by IR spectroscopy. The structure and properties of PI fibers were studied by scanning electron microscopy, thermal analysis, and by measuring the stress-strain properties.

     

Effects of monomer structure and imidization degree on mechanical properties and viscoelastic behavior of thermoplastic polyimide films

Two thermoplastic polyimides based on a common diamine (3,4′-ODA) were synthesized using different dianhydrides, namely ODPA and BPDA by a two step method. Molecular weight was controlled by using PA as an end capping agent. Effects of imidization degree on the mechanical properties and viscoelastic behavior of thermoplastic polyimide films were investigated. Film samples with varying degrees of imidization were characterized using FTIR, DMTA and tensile properties testing. It was found that two polyimides have different rates of imidization because of difference in monomer reactivity and molecular structure. It was observed that with an increase in imidization degree there was a decrease in thermoplastic response and a change in viscoelastic behavior from liquid-like to solid-like. With increase in imidization degree the tensile modulus and tensile strength of the films were increased, whereas elongation at break and tensile breaking energy were found to decrease after a certain imidization temperature.     

Extraction of cellulose and preparation of nanocellulose from sisal fibers

In this work a study on the feasibility of extracting cellulose from sisal fiber, by means of two different procedures was carried out. These processes included usual chemical procedures such as acid hydrolysis, chlorination, alkaline extraction, and bleaching. The final products were characterized by means of Thermogravimetric Analysis (TGA), Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD), Differential Scanning Calorimetry (DSC) and Scanning Electronic Microscopy (SEM). The extraction procedures that were used led to purified cellulose. Advantages and disadvantages of both procedures were also analyzed. Finally, nanocellulose was produced by the acid hydrolysis of obtained cellulose and characterized by Atomic Force Microscopy (AFM).     

Structure and properties of polyimide fibers containing benzimidazole and Amide Units

Co‐polyimide (co‐PI) fibers with outstanding mechanical properties were fabricated via thermal imidization of polyamic acids, derived from a new design of combining the amide and benzimidazole diamine monomers, 4‐amino‐N‐(4‐aminophenyl)benzamide (DABA) and 2‐(4‐aminophenyl)‐5‐aminobenzimidazole (BIA), with 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA). The crystalline structure and micromorphology of the prepared co‐PI fibers were investigated by synchrotron wide‐angle X‐ray diffraction (WAXD) and small‐angle X‐ray scattering (SAXS). The two‐dimensional WAXD spectra imply that the co‐PI fibers possess a structure between smectic‐like and three‐dimensionally ordered crystalline phase, and all the obtained fibers are highly oriented along the fiber axis. SAXS patterns exhibit a pair of meridional scattering streaks for the homo‐PI (BPDA/BIA) fiber, suggesting the presence of periodic lamellar structure. The incorporation of DABA into the polymer chains destroyed the lamellar structure but led to smaller size of microvoids upon increasing DABA moiety, based on SAXS analysis. The co‐PI fibers, with the molar ratio of BIA/DABA being 7/3, exhibited the optimum tensile strength and modulus of 1.96 and 108.3 GPa, respectively, attributed to the well‐defined ordered and dense structure. The chemical structure and molecular packing significantly affected the thermal stability of fibers, resulting in the different glass transition temperatures (T_g) from 350 to 380 °C. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 183–191     

Correlation between hydrogen‐bonding interaction and mechanical properties of polyimide fibers

Novel co‐polymerization polyimide (PI) fibers based on 4,4′‐oxydianiline (ODA)‐pyromellitic dianhydride (PMDA) were prepared. 2‐(4‐Aminophenyl)‐5‐aminobenzimidazole (PABZ) containing the N? H group was introduced into the structure of the fibers as the proton donor. The results of Fourier transform infrared (FTIR) and dynamic mechanical analysis (DMA) showed that hydrogen bonding occured between the N? H group and chains, which strongly enhanced interchain interaction. This hydrogen bonding interaction increased the tensile strength and initial modulus of the PI fibers up to 2.5 times and 26 times, respectively, compared to those of homo‐PI PMDA‐ODA fibers with no hydrogen‐bonding interaction because of the absence of proton donors after the imidization process. In the mean time, glass transition temperature (T_g) of the modified PI fibers was found to be 410–440°C, which was higher than that of the homo‐PI PMDA‐ODA fibers. From the result, a novel access to molecular design and manufacture of high performance PI fibers with good properties could be provided. Copyright © 2009 John Wiley & Sons, Ltd.     

Effect of degree of saponification on structural and property change of poly(Vinyl alcohol) fibers

To improve the drawability and finally the mechanical properties, poly(vinyl alcohol)s (PVA₈₆, PVA₉₃, and PVA₉₉) with respective degrees of saponification of 86, 93, and 99% were synthesized using solution polymerization. Following the synthesis dimethylsulfoxide (DMSO) solutions of the PVAs were gel-spun into methanol. After extraction of DMSO from the as-spun fibers the dried fibers were first drawn at 120 °C then at 180 °C. An analysis of the structure and properties of the fibers was performed using FT-IR, differential scanning calorimetry (DSC) and a fiber strength tester. The degree of saponification had an effect on the formation and intensity of the intermolecular hydrogen bonds, melting, drawability and strength of the PVA fibers. Low degrees of saponification weakened the intermolecular hydrogen bonds and interfered with the formation of crystallites, causing low melting points and low heat of fusion. Generally, drawing was easier to carry out at lower temperature, and higher draw ratios could be obtained, leading to higher fiber strengths. Copyright © 2003 John Wiley & Sons, Ltd.     

Structure and properties of polyimide films during a far‐infrared‐induced imidization process

The conversion of poly(amic acid) into polyimide (PI) was achieved with far‐infrared radiation (FIR) and conventional thermal treatments. The structure and properties of PI films during different stages of imidization were studied with Fourier transform infrared spectroscopy, weight‐loss analysis during imidization, tensile property measurements, and dynamic mechanical thermal analysis. The effects of the imidization degree, postimidization, and solvent on the thermal and mechanical properties of PI films were quantitatively investigated. The corresponding structural changes were also examined. The experimental results showed that the imidization process proceeded more quickly and more completely in an FIR oven than in a conventional oven. A prolonged FIR treatment at a lower temperature (25–100 °C) accelerated the imidization process. The tensile stress–strain curves had a fanlike distribution with the development of the FIR imidization process and a fishtail distribution with conventional thermal imidization. During FIR imidization, the best tensile properties were obtained at 340 °C, and thermooxidative degradation occurred at about 420 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2490–2501, 2004     

Electrochemical studies for the electroactivity of amine-capped aniline trimer on the anticorrosion effect of as-prepared polyimide coatings

The electroactive polyimide consisting of various content of amine-capped aniline trimers (ATs) have been successfully synthesized and characterized by Fourier-Transformation infrared and UV-visible absorption spectroscopy. The electroactivity of as-prepared polyimides was tested by electrochemical cyclic voltammetry (CV) studies. It was noticed that the as-prepared electroactive polyimide with higher content of amine-capped ATs shows higher electroactivity (i.e., larger redox current) than that of non-electroactive polyimide, leading to enhance corrosion protection efficiency on cold-rolled steel (CRS) electrodes. This enhanced corrosion protection efficiency has been explained based on a series of electrochemical measurements such as corrosion potential, polarization resistance, corrosion current and electrochemical impedance spectroscopy (EIS) studies in 5 wt-% NaCl electrolyte. This significant enhancement of corrosion protection on CRS electrodes as compared to non-electroactive polyimide might probably be attributed to the redox catalytic property of as-prepared electroactive polyimide coatings inducing the formation of passive layer of metal oxide.     

Inducing a high twisted conformation in the polyimide structure by bulky donor moieties for the development of non-volatile memory

Two polyimides, PI(DAT-6FDA) and PI(DAPT-6FDA), from N-(2,4-diaminophenyl)-N,N-diphenylamine (DAT) or N-(4-(2′,4′-diaminophenoxy)phenyl-N,N-diphenylamine (DAPT) and 4,4′-(hexafluoroisopropylidene)diphthalic anhydride (6FDA) were prepared to clarify the structural effect on the resulting memory properties. The memory device based on PI(DAT-6FDA) showed an unstable volatile behavior, while the device based on PI(DAPT-6FDA) with a more bulky donor (D) unit exhibited a stable non-volatile FLASH type memory characteristic with a long retention time over 10⁴ s. The theoretical simulation based on the density functional theory (DFT) suggested that the greater distinct charge separation between the ground and charge transfer (CT) states led to a highly stable memory behavior. Also, it was clarified that PI(DAPT-6FDA) had a highly twisted conformation compared to PI(DAT-6FDA) in the ground state, and a more twisted dihedral angle between the D and acceptor (A) units was induced in the CT state, which led to the non-volatile memory characteristic.     

蛇莓果实总花色苷含量测定方法的比较

为了寻求快速、经济地测定蛇莓果实总花色苷含量的方法,采用单-pH法和pH示差法进行测定,比较分析了两种方法测定结果的差异性.结果表明,两种pH法测定的吸光度与浓度均具有良好的线性关系,测定结果没有显著性差异.两种pH法均能用于蛇莓果实总花色苷含量的测定,且需要在相同溶剂中进行,其中单一pH法操作更简便.