Bi2Te3/Sb超晶格纳米线的外延生长和热电测量

通过脉冲电沉积,外延生长出小单元长度的Bi₂Te₃/Sb超晶格纳米线.借助哈曼方法,测量了超晶格纳米线阵列的热电性能,330 K时的ZT值可达0.15.研究了Bi₂Te₃/Sb超晶格纳米线阵列器件的制冷或者加热能力,发现器件的上下表面的最大温差可以达到6.6 K.     

Sb2Te3 纳米结构的制备与表征

以室温热电性能优异的传统热电材料Sb₂Te₃为研究对象,利用化学气相沉积法制备Sb₂Te₃单晶纳米结构,并研究其生长机理.实验结果表明,不加催化剂时Sb₂Te₃易生长成六方纳米盘,在金催化剂条件下定向生长成纳米线.Sb₂Te₃的形貌与其晶体结构和生长机理有关.Sb₂Te₃为三角结构,Sb和     

大规模合成具有氧空位的多孔Bi2O3用于有效降解亚甲基蓝

光催化降解有机污染物由于其具有低能耗和绿色环保的特点,已经成为研究的热点. 氧化铋纳米晶体的带隙在2.0∽2.8 eV之间,利用它催化可见光降解有机污染物具有较高的活性,从而引起了越来越多的关注. 尽管近年来已经开发了几种制备Bi₂O₃基半导体材料的方法,但是仍然难以用简单的方法大规模地制备高活性的Bi₂O₃催化剂. 因此,开发简单可行的大规模制备Bi₂O₃纳米晶体的方法对于工业废水处理的潜在应用具有重要意义. 本文通过蚀刻商用BiSn粉末,然后进行热处理,成功地大规模制备了多孔Bi₂O₃. 获得的多孔Bi₂O₃在亚甲基蓝(MB)的光催化降解中表现出优异的活性和稳定性. 对该机理的进一步研究表明,多孔Bi₂O₃合适的能带结构允许生成活性氧物种,例如O₂^-·和·OH,可有效降解MB.     

脉冲激光沉积温度及氧压对Bi2Sr2Co2Oy热电薄膜晶体结构与电输运性能的影响

利用脉冲激光沉积技术在c-Al₂O₃单晶基片上制备了Bi₂Sr₂Co₂O_y热电薄膜并研究了沉积温度和氧压对薄膜晶体结构及电输运性能的影响.在最佳沉积条件下制备的单相、c轴取向的Bi₂Sr₂Co₂O_y薄膜的室温电阻率ρ和塞贝克系数S分别为2.9mΩ/cm和110μupV/K,其功率因子S²/ρ好于在单晶样品上得到的值.此外,该薄膜在低温下表现出较强的负磁阻效应,在2K,9T时达到了40%.     

聚对苯撑/LiNi0.5Fe2O4纳米复合热电材料的制备及其性能研究

本文以流变相反应法原位合成了聚对苯撑/LiNi_0.5Fe₂O₄纳米复合热电材料,并对其热电性能进行表征,研究了放电等离子烧结时保温时间对其热电性能的影响.结果发现,复合材料铁氧体颗粒粒径为100---300nm,其外部被一层聚对苯撑膜包覆.电子在Fe²⁺和Fe³⁺之间的跳跃机理在铁氧体电导中占主导作用,因此聚对苯撑/LiNi_0.5Fe₂O₄复合材料具有n型导电特性.随着保温时间增加,复合材料电导率基本不变,但热导率逐渐增大且Seebeck系数逐渐减小,导致热电优值系数降低.由于结合了有机物高电导率和低热导率以及无机材料高赛贝克系数的优点,所制备的复合材料热电性能较单一材料有较大提高.     

复合层状Bi7Ti4NbO21铁电陶瓷的结构与介电和压电性能研究

制备了Bi₇Ti₄NbO_{21，Bi4Ti3O12及Nb掺杂Bi4Ti3O12(Nb-Bi4Ti3O12)层状结构铁电陶瓷材料.结合Nb-Bi 4Ti3O12的介电温谱和 退极化实验结果，研究了Bi7Ti4NbO21的晶体结构 对其介电、压电性能的影响 .高分辨透射电镜结果表明，在Bi7Ti4NbO21中， 沿着c轴方向，(Bi2Ti3O10)^2-和(BiTiNbO7)^2-两个类钙钛矿层分别 与(Bi2O2)²⁺层叠加堆积而成.这种晶体结构决定了Bi7Ti4NbO21的 介电温谱在668℃和845℃出现介 电双峰.结合极化样品的退化实验分析，说明材料在这两个温度附近发生了铁电—铁电相变 、铁电—顺电相变，分别是(Bi2Ti3O10)^{2-< /sup>和(BiTiNbO7)2-层状 结构发生微观结构相变的结果.在退极化过程中，由于受热时钙钛矿层内空位引起的缺陷偶 极子的定向排列受到破坏，引起材料部分退极化，表现为300℃热处理后Bi7Ti 4NbO 21的压电活性降低了10%，显示了室温下材料的压电性能来源于自发极化的固有电 偶极子和缺陷偶极子的共同贡献.}}     

Cu掺杂AgSbTe2化合物的相稳定、晶体结构及热电性能

利用熔融快淬结合放电等离子烧结(SPS), 制备了Cu_xAg_1-xSbTe₂(x= 0---0.3)样品. 粉末X射线衍射(XRD)分析结果显示, SPS处理以前, 含Cu样品形成NaCl型结构的固溶体, 而未加入Cu的样品析出Ag₂Te第二相. 根据热分析和XRD测量结果, Cu的加入能够有效抑制Ag₂Te的析出, 但同时会在快淬样品中产生少量非晶相. 在温度升高到540 K左右时, 非晶相发生晶化, 形成Sb₇Te亚稳相, 并最终转变成Sb₂Te₃稳定相. 对快淬样品进行低温SPS快速处理后, x =0.1样品为面心立方结构的单相化合物, 但是x =0.2, 0.3的样品分别析出第二相Sb₇Te和Sb₂Te₃. 由于析出第二相, x=0.2, 0.3样品的电导率增大, Seebeck系数减小, 热导率相应升高, 综合热电性能降低. x=0.1单相样品的功率因子与文献报道的AgSbTe₂化合物相当. 元素替代的合金化效应 增强了Cu_0.1Ag_0.9SbTe₂化合物的声子散射, 有效降低了样品的热导率. 因此, 单相样品Cu_0.1Ag_0.9SbTe₂表现出较佳的热电性能, 在620 K时热电优值达到1.     

Nd掺杂对Bi4Ti3O12铁电薄膜的微结构和铁电性能的影响

利用溶胶-凝胶法在Pt/Ti/SiO₂/Si(100)衬底上制备了Nd掺杂Bi₄Ti₃O₁₂(Bi_4-xNd_xTi₃O₁₂, x=0.00,0.30,0.45,0.75,0.85,1.00,1.50)铁电薄膜样品.研究了Nd掺杂对Bi₄Ti₃O₁₂薄膜的微结构和铁电性能的影响.研究结果表明:Nd掺杂未改变Bi₄Ti₃O₁₂薄膜的基本晶体结构.在掺杂量x<0.45时,Nd³⁺只取代类钙钛矿层中的A位Bi³⁺.当x=0.45时,样品剩余极化强度达最大值,在270kV·cm^-1的电场下为32.7μC·cm^-2.掺杂量进一步增加时,结构无序度开始明显增大,Nd³⁺开始进入(Bi₂O₂)²⁺层,削弱其绝缘层和空间电荷库的作用,导致材料剩余极化逐渐下降.当掺杂量x达到1.50时,掺杂离子最终破坏(Bi₂O₂)²⁺层的结构,材料发生铁电-顺电相变.     

机械合金化过程对硫化铋块体热电性能的影响机理

以机械合金化法(MA)结合放电等离子烧结技术(SPS)制备了Bi₂S₃多晶块体热电材料. 研究了MA过程中干磨转速、湿磨时间和湿磨介质对Bi₂S₃多晶热电材料电传输性能的影响. 分析了样品的物相, 观察了显微组织, 测试了电传输性能和热传输性能. 研究表明, 以无水乙醇为湿磨介质时, 随着湿磨时间的延长, 出现了微量Bi₂O₃第二相, 样品的晶粒尺寸减小, 电阻率大幅增加, 功率因子下降. 以丙酮为湿磨介质时, 虽然不存在微氧化反应, 但是由于样品中存在大量孔洞, 导致功率因子降低. 425 r/min 干磨15 h后未湿磨的样品在573 K取得最大的ZT值0.25, 是目前文献报道的最高值.     

热压制备(AgSbTe2)100-x-(GeTe)x合金的热电性能

以Pb粉、Te粉、Ag粉、Ge粉为原材料,在真空气氛下合成(AgSbTe₂)_100-x-(GeTe)_x (x=80---90) (TAGS)合金热电材料, X射线衍射(XRD)分析表明,热压烧结后合金具有低温菱形结构. 通过热压烧结法将TAGS粉末制备成块体材料,运用XRD和扫描电子显微镜对材料的物相成分、 晶体结构和形貌进行了表征.采用直流四探针法测定样品的电导率,当样品两端的温差为1---4℃ 的情况下测量Seebeck系数.通过材料热电性能测试,研究了30---500℃温度范围内不同组分 样品性能参数的变化.结果表明,所制备的TAGS热电材料具有纳米结构, 其性能随着组分的变化而变化, TAGS-80具有较好的热电性能,在530℃时具有最高热电优值(ZT=1.80).     

The absolute thermoelectric powers of some liquid alloys

Measurements of the absolute thermoelectric powers of several liquid alloys as a function of temperature and composition are reported.

The alloys Hg-In and Hg-Tl were studied. In both cases the absolute thermoelectric powers show a minimum when plotted against concentration at low concentrations.

The system Hg-Na was measured over the range 0 at. % to 10 at. % Na. The absolute thermoelectric power shows a very sharp minimum at about 5.0 at. % Na. This minimum becomes sharper with increasing temperature. The effect is more marked in this case than in the previous two cases.

Measurements of absolute thermoelectric power of the alloys of cadmium in mercury and gold in mercury show that it becomes less negative as the metals are added to mercury. This is the opposite effect to that found in the previous two alloys.

Measurements made on the Cd-In system show no minimum. The results on these alloys are discussed with relation to Mott's theory for liquid mercury (Mott 1966).     

半导体温差发电过程的模型分析与数值仿真

本文提出一种新型的半导体温差发电模型,在温差发电过程的数值模拟中考虑了热电单元之间封闭腔体内空气传热的影响.同时进一步运用有限元的数值计算方法对不同电臂对数和不同型号温差发电模型的温度场、电压场进行了数值仿真计算,并对仿真结果进行分析.结果表明:采用127对热电单元模型计算的能量转换效率随冷热端温差增大而迅速提高,与采用1对热电单元模型计算的能量转换效率之差从冷热端温差为20℃的0.39%提高到冷热端温差为220℃时的5.16%,能量转换效率比1对热电单元平均高出3.02%.冷端温度恒定在30℃时,温差发电芯片的输出电压、功率以及能量转换效率均随着电偶臂的横截面积的增大而提高,且电偶臂冷热两端的温差越大提高幅度也越大,而温差发电芯片内阻则与电偶臂横截面积成反比关系,当温差为220℃时对应的输出功率最高达28.9 W.     

Performance of thermoelectric generator with graphene nanofluid cooling

Improvement of the heat transfer of the cold side is one of the approaches to enhance the performance of TEG systems.As a new type of heat transfer media, nanofluids can enhance the heat transfer performance of working liquid significantly.Based on a three-dimensional and steady-state numerical model,the heat transfer and thermoelectric conversion properties of TEG systems were studied. Graphene anoplatelet aqueous nanofluids were used as the coolants for the cold side of the TEG system to improve the heat transfer capacity of the cold side. The results showed that the heat absorbed by the hot side, voltage, output power, and conversion efficiency of the TEG system were increased greatly by the nanofluid coolants.The output power and the conversion efficiency using 0.1-wt% graphene nanoplatelet aqueous nanofluid as the coolant are enhanced by 26.39% and 14.74%, respectively.     

Linear and nonlinear mesoscopic thermoelectric transport with coupling with heat baths

Decades of research on thermoelectrics stimulated by the fact that nano- and meso-scale thermoelectric transport could yield higher energy conversion efficiency and output power has recently uncovered a new direction on inelastic thermoelectric effects. We introduce the history, motivation, and perspectives on mesoscopic inelastic thermoelectric effects.     

A 200 W diode-side-pumped CW 2 μm Tm:YAG laser with water cooling at 8°C

A water-cooled 785 nm diode-side-pumped high-power CW Tm:YAG laser system at 2 μm is reported. 200 W output power is achieved with cooling water running at 8°C. As far as we know, this is the highest output power for a diode-pumped all solid-state 2 μm Tm:YAG laser. The output corresponds to optical-to-optical conversion efficiency of 11.2%, with a slope efficiency of about 22.8%. To make the system structure simple, only deionized water is used as the coolant instead of alcohol- or glycol-water mixture or the liquid nitrogen in the reported high-power Tm rod laser experiments, which were performed at low temperature near the freezing point of water, or even below.     

Die Änderung der Thermospannung im Magnetfeld (2. Ettingshausen-Nernst-Effekt) bei Kupfer,Silber und Palladium

An experimental device is described for measuring the change in thermoelectric power in magnetic fields (2nd Ettingshausen-Nernst-effect). The change in thermoelectric power was determined for the metals Cu, Ag, Pd at magnetic fields up to 20 kOe at liquid nitrogen temperature. At low magnetic fields there is a proportionality toB ². The temperature dependence of the 2nd Ettingshausen-Nernst-effect is reported for Cu.     

Strategies for optimizing the thermoelectricity of PbTe alloys

The thermoelectric materials have been considered as a potential candidate for the new power generation technology based on their reversible heat and electricity conversion.Lead telluride(Pb Te) is regarded as an excellent mid-temperature thermoelectric material due to its suitable intrinsic thermoelectric properties.So tremendous efforts have been done to improve the thermoelectric performance of Pb Te,and figures of merit,z_T 2.0,have been reported.Main strategies for optimizing the thermoelectric performance have been focused as the main line of this review.The band engineering and phonon scattering engineering as two main effective strategies are systemically summarized here.The band engineering,like band convergence,resonant levels,and band flatting have been addressed in improving the power factor.Additionally,phonon scattering engineerings,such as atomic-scale,nano-scale,meso-scale,and multi-scale phonon scatterings have been applied to reduce the thermal conductivity.Besides,some successful synergistic effects based on band engineerings and phonon scatterings are illustrated as a simultaneous way to optimize both the power factor and thermal conductivity.Summarizing the above three main parts,we point out that the synergistic effects should be effectively exploited,and these may further boost the thermoelectric performance of Pb Te alloys and can be extended to other thermoelectric materials.     

液氮环境下的热载流子高功率微波探测器

为提高热载流子高功率微波探测器的灵敏度和降低环境温度对探测器性能的影响,开展了液氮环境下的热载流子探测器研究。提出了局部使用可阀合金块的BJ-100型热载流子探测器制作工艺,增强了探测器的抗温度冲击能力。测试结果表明,探测器硅片焊接的结合力大于4.9 N,能够承受从常温到液氮的反复温度冲击。利用100 kW微波源开展了热载流子探测器在室温和液氮环境下的灵敏度测试实验,结果表明:探测器输出波形与肖特基二极管检波器输出波形一致;在保持偏置电流相同的条件下,相较于常温环境,探测器在液氮环境下的相对灵敏度提升约20倍,输出电压可达V级。     

High efficient double end-pumped <Emphasis Type="Italic">b</Emphasis>-cut Tm,Ho:YAlO<Subscript>3</Subscript> laser

High efficient continuous wave (CW) and acousto-optical (AO) Q-switched operation of a b-cut Tm,Ho:YAlO₃ (Tm,Ho:YAP) laser are reported in the paper. The Tm,Ho:YAP crystal was cooled by liquid nitrogen and pumped by a fiber-coupled laser diode (LD). Different pump wavelengths were tried in the experiment. An 8.36-W output power was acquired at 2.12 μm in the CW operation with an optical-optical conversion efficiency of 33.3%, and an 8.14-W average power was obtained at the pulse repetition frequency (PRF) of 10 kHz with an optical-optical conversion efficiency of 32.4%.     

High efficiency 2.05-μm CW and AO Q-switched operation of diode end-pumped Tm,Ho:GdVO4 laser

The continuous-wave (CW) and acoustooptically (AO) Q-switched operation of a Tm (4 at %), Ho (0.4 at %):GdVO₄ laser at a 2.05-μm wavelength were reported in this paper. The Tm,Ho:GdVO₄ crystal was cooled by liquid nitrogen and end pumped by a 29.8-W fiber-coupled laser diode at 801 nm. A conversion efficiency of 41% and a slope efficiency of 46% were acquired with a continuous-wave output power of 12.2 W. An average power of 11.6 W was obtained at a pulse repetition frequency (PRF) of 10 kHz, corresponding to an optical-to-optical conversion efficiency of 38.9% and a slope efficiency of 41.4%. The energy per pulse of 1.8 mJ in 14 ns was achieved at 5 kHz with a peak power of 130 kW.