Adiabatic frequency conversion of ultrafast pulses

A new method for efficient, broadband sum and difference frequency generation of ultrafast pulses is demonstrated. The principles of the method follow from an analogy between frequency conversion and coherent optical excitation of a two-level system. For conversion of ultrafast pulses, the concepts of adiabatic conversion are developed further in order to account for dispersion and group velocity mismatch. The scheme was implemented using aperiodically poled nonlinear crystals and a single step nonlinear mixing process, leading to conversion of near-IR (∼790 nm) ultrafast pulses into the blue (∼450 nm) and mid-IR (∼3.15 μm) spectral regions. Conversion bandwidths up to 15 THz FWHM and efficiencies up to 50% are reported.     

Diode-pumped Yb:KYW femtosecond laser frequency comb with stabilized carrier-envelope offset frequency

We describe the detection and stabilization of the carrier envelope offset (CEO) frequency of a diode-pumped Yb:KYW (ytterbium-doped potassium yttrium tungstate) femtosecond oscillator that is spectrally centered at 1033 nm. The system consists of a diode-pumped, passively mode-locked femtosecond laser that produces 290 fs pulses at a repetition rate of 160 MHz. These pulses are first amplified, spectrally broadened and temporally compressed to 80 fs, and then launched into microstructured fiber to produce an octave-spanning spectrum. An f-2f nonlinear interferometer is employed with the broadened spectrum to detect and stabilize the CEO frequency through feedback to the pump laser current. These results demonstrate that such a Yb-doped tungstate laser can provide an efficient, compact, high-repetition-rate optical frequency comb with coverage from 650–1450 nm.     

Tunable, high-repetition-rate, femtosecond pulse generation in the ultraviolet

We report efficient generation of tunable femtosecond pulses in the ultraviolet (UV) by intracavity doubling of a visible femtosecond optical parametric oscillator (OPO). The OPO, based on a 400 microm BiB3O6 crystal and pumped at 415 nm in the blue, can provide visible femtosecond signal pulses across 500-710 nm. Using a 500 microm crystal of beta-BaB2O4 internal to the OPO cavity, efficient frequency doubling of the signal pulses into the UV is achieved, providing tunable femtosecond pulses across 250-355 nm with up to 225 mW of average power at 76 MHz. Cross-correlation measurements result in UV pulses with durations down to 132 fs for 180 fs blue pump pulses.     

Investigation of luminescence processes in YAG single crystals irradiated by 50 MeV electron beam

Absorption, emission and excitation spectra of 50 MeV electron beam irradiated and as-grown YAG single crystals were studied and compared in the 10–300 K temperature range using time-resolved luminescence spectroscopy under UV/VUV/XUV excitation by synchrotron radiation and cathodoluminescence. The emission spectra consist of intrinsic (excitonic) and defect related non-elementary bands in the VIS/UV range. It is shown that fast electrons create stable F and F⁺ color centers with characteristic emission and absorption bands in the visible/UV range. Induced absorption caused from these defects starts at 4.2 eV. Energy transfer from host to color centers is not an efficient process.     

Efficient ultrafast ultraviolet generation based on frequency doubling in short-period periodically-poled KTiOPO4 crystal

We have efficiently generated ultrafast coherent ultraviolet (UV) pulses based on second-harmonic generation in a periodically-poled KTiOPO₄ crystal with the period as short as 2.55 μm. The highest output power is measured to be 20.1 mW at 377.1 nm with the conversion efficiency of 15.6%. Such an output wavelength is probably among the shortest ones generated by forward second-harmonic generation in a periodically-poled KTiOPO₄ crystal.     

57 W, 27 fs pulses from a fiber laser system using nonlinear compression

We report on the generation of 27 fs pulses with an average output power of 57 W and a repetition rate of 78 MHz. The pulses are generated by combining a high average power fiber chirped pulse amplification (FCPA) system with a microstructured large-mode-area fiber for nonlinear compression. The FCPA system delivers 270 fs pulses in a linearly polarized beam with diffraction-limited quality. Nonlinear compression is achieved by launching the pulses into a short (few cm) piece of microstructured fiber and subsequent compression by a pair of chirped mirrors. PACS  42.55.Wd; 42.55.Xi, 42.65.Re     

Ultrasound-assisted synthesis of ZnO photocatalysts for gas phase pollutant remediation: Role of the synthetic parameters and of promotion with WO3

The synthesis of ZnO photocatalysts by ultrasound-assisted technique was here investigated. Several experimental parameters including the zinc precursor (acetate, chloride, nitrate), sonication conditions (amplitude, pulse) and post-synthetic thermal treatment (up to 500 °C) were studied. Crystalline ZnO samples were obtained without thermal treatments due to the adopted reactant ratios and synthesis temperature. Sonication plays a major role on the morphological oxide features in terms of particle size and surface area, the latter showing a 20-fold increase with respect to conventional synthesis. Interestingly, 1 and 3 s sonication pulses led to morphological properties similar to continuous sonication. A thermal treatment at moderate temperatures (400–450 °C) promoted the loss of surface hydroxylation and the formation of lattice defects, while higher temperatures were detrimental for the sample morphology. The prepared ZnO was decorated with WO₃ particles comparing an ultrasound-assisted technique using 1 s pulses with a conventional approach, giving rise to composites with promoted visible light absorption. Samples were tested towards the photocatalytic degradation of nitrogen oxides (500–1000 ppb) in humidified air under both UV and visible light. By carefully controlling the synthetic procedure, better performance were observed with respect to the commercial benchmark. Samples from ultrasound-assisted syntheses, also in the case of pulsed sonication, showed consistently better results than conventional references, in particular for ZnO-WO₃ composites. The composite by ultrasound-assisted synthesis showed > 95% degradation in 180 min and doubled NO_x degradation under visible light with respect to the conventional composite.     

InGaAs diode laser system generating pulses of 580 fs duration and 366 W peak power

This paper reports the generation of fs light pulses by a passively mode-locked InGaAs master oscillator power amplifier (MOPA) system. The laser system generates chirped pulses with 6.2 ps duration, a center wavelength of 922 nm and 4 GHz repetition rate. Pulse compression by an external grating compressor reduces the pulse duration to 580 fs. The average power of the compressed pulses of 851 mW corresponds to a peak power of 366 W.     

Characterization and antibacterial functions of Ag–TiO<Subscript>2</Subscript> and W–TiO<Subscript>2</Subscript> nanostructured thin films prepared by sol-gel/laser-induced technique

A novel sol-gel/laser-induced technique (SGLIT) has been developed to form nanocrystalline titanium dioxide (TiO₂) based thin films with an improved antibacterial performance. TiO₂ precursor films loaded with W⁺⁶ and Ag⁺² ions (W–TiO₂, Ag–TiO₂) were prepared separately by sol-gel method and spin-coated on microscopic glass slides. As-dried films were subjected to KrF excimer laser pulses at optimized parameters to generate mesoporous anatase and rutile phases at room temperature. The anatase phase was obtained after irradiation with 10 laser pulses only at 75–85 mJ/cm² fluence in W–TiO₂ films. However, higher number of laser pulses and higher W⁺⁶ content favored the formation of rutile. Whereas Ag–TiO₂ films exhibited anatase up to 200 laser pulses at the same fluence. The films were characterized by using XRD, FEG-SEM, TEM and UV-Vis spectrophotometer to investigate the crystallographic structure, phase transformation, surface morphology, film thickness and the optical properties. A crystallite size of approximately 20 nm was achieved from the anatase prepared by SGLIT. The films exhibited an enhanced antibacterial function against E-Coli cells under the UV excitation.     

Aryltriazene photopolymer thin films as sacrificial release layers for laser-assisted forward transfer systems: study of photoablative decomposition and transfer behavior

Thin films of a tailor-made photodecomposible aryltriazene polymer were applied in a modified laser-induced forward transfer (LIFT) process as sacrificial release layers. The photopolymer film acts as an intermediate energy-absorbing dynamic release layer (DRL) that decomposes efficiently into small volatile fragments upon UV laser irradiation. A fast-expanding pressure jet is generated which is used to propel an overlying transfer material from the source target onto a receiver. This DRL-assisted laser direct-write process allows the precise deposition of intact material pixels with micrometer resolution and by single laser pulses. Triazene-based photopolymer DRL donor systems were studied to derive optimum conditions for film thickness and laser fluences necessary for a defined transfer process at the emission wavelength of a XeCl excimer laser (308 nm). Photoablation, surface detachment, delamination and transfer behavior of aryltriazene polymer films with a thickness from 25 nm to ∼400 nm were investigated in order to improve the process control parameters for the fabrication of functional thin-film devices of microdeposited heat- and UV-sensitive materials.     

Femtosecond OPO based on LBO pumped by a frequency-doubled Yb-fiber laser-amplifier system for CARS spectroscopy

We present detailed investigations of a femtosecond green-pumped optical parametric oscillator (OPO) based on lithium triborate. As pump source, a frequency-doubled Yb-fiber laser-amplifier system is used. The OPO generates signal pulses tunable over a spectral range from 780 to 940 nm and idler pulses tunable from 1630 to 1190 nm. More than 250 mW are generated in the signal beam and more than 300 mW in the idler beam. Without dispersion compensation chirped signal pulses with a pulse duration between 100 and 250 fs are measured. Using this system for coherent anti-Stokes Raman scattering spectroscopy, vibrational resonances between 1110 and 6760 cm⁻¹ can be excited. Due to the chirped pulses, a spectral resolution of 100 cm⁻¹ is achieved, which is 2.5 times higher compared to an excitation with time-bandwidth limited pulses.     

Ponderomotive ion acceleration in dense plasmas at super-high laser intensities

Short laser pulses at super-high intensities such as those proposed in the Extreme Light Infrastructure (ELI) project open new prospects for efficient acceleration of ions in overdense plasmas. A simple analytical model and numerical simulations demonstrate that pulses with intensities exceeding 10²² W/cm² may efficiently accelerate ions to high energies up to a few GeV. Maximum ion energy and the energy spectrum of the accelerated ions can be tuned by an appropriate choice of laser pulse intensity and duration at a given plasma density distribution.     

Sol–gel glass-ceramics comprising rare-earth doped SnO<Subscript>2</Subscript> and LaF<Subscript>3</Subscript> nanocrystals: an efficient simultaneous UV and IR to visible converter

Abstract  

We report a novel class of nanostructured glass-ceramics comprising two co-existing rare-earth doped nanocrystalline phases, SnO₂ semiconductor nanocrystal (quantum dot), and LaF₃, presenting sizes at around 4.6 and 9.8 nm, respectively, embedded into a silica glass matrix for an efficient simultaneous UV and IR to visible photon conversion. On one hand, the wide and strong UV absorption by SnO₂ quantum dot and subsequent efficient energy transfer to Eu³⁺ and, on the other hand, the also very efficient IR to visible up-conversion with the pair Yb³⁺–Er³⁺ partitioned into low phonon LaF₃ nanocrystalline environment, yield to visible emissions with application in improving the spectral response of photovoltaic solar cells.     

VUV超短脉冲的产生及其在超快动力学中的应用

真空紫外超短脉冲激光具有波长短、单光子能量高、脉宽小等特点,在飞秒化学以及超快动力学等方面具有相当广泛的应用前景.由于直接利用受激辐射获得真空紫外超短脉冲是相当困难,因此利用非线性频率转换技术,超短脉冲与惰性气体相互作用,将红外、可见或紫外光波段的超短脉冲转换到真空紫外波段是目前获得紫外超短脉冲最快捷有效的方式.围绕真空紫外超短脉冲的产生及其在超短动力学中应用展开,介绍了产生真空紫外超短脉冲的高斯谐波、空心光纤四波混频和光丝四波混频的方法,对其优缺点作了评述,并对真空紫外超短脉冲激光在超快动力学过程中的应用进行了简单的总结.     

Modulator‐Free Coherent‐One‐Way Quantum Key Distribution

Time‐bin encoding is an attractive method for transmitting photonic qubits over long distances with minimal decoherence. It allows a simple receiver for quantum key distribution (QKD) that extracts a key by measuring time of arrival of photons and detects eavesdropping by measuring interference of pulses in different time bins. In the past, coherent pulses have been generated using a CW laser and an intensity modulator. A greatly simplified transmitter is proposed and demonstrated here that works by directly modulating the laser diode. Coherence between pulses is maintained by a weak seed laser. The modulator‐free source creates time‐bin encoded pulses with a high extinction ratio (29.4 dB) and an interference visibility above 97 %. The resulting QKD transmitter gives estimated secure key rates up to 4.57 Mbit/s, the highest yet reported for coherent‐one‐way QKD, and can be programmed for all protocols using weak coherent pulses.     

Elimination of cracking during UV laser ablation of SrTiO3 single crystals by employing a femtosecond laser

We have performed a comparative study of UV laser ablation of SrTiO₃ with nanosecond- and sub-picosecond sources, respectively. The experiments were performed with lasers at a wavelength of 248 nm and pulse durations of 34 ns and 500 fs. Femtosecond ablation turns out to be more efficient by one order of magnitude and eliminated the known problem of cracking of SrTiO₃ during laser machining with longer pulses. In addition, the cavities ablated with femtosecond pulses display a smoother surface with no indication of melting and well-defined, sharp edges. These effects can be explained by the reduced thermal shock effect on the material by using ultrashort pulses.     

A comprehensive study of Nd:YAG,Nd:YAlO<Subscript>3</Subscript>, Nd:YVO<Subscript>4</Subscript> and Nd:YGdVO<Subscript>4</Subscript> lasers operating at wavelengths of 0.9 and 1.3 μm. Part 2: passively mode locked-operation

This paper reports on the generation of picosecond (ps) laser pulses by self-phase-adjusting additive-pulse-mode-locking (PSA) at wavelengths of 0.9 and 1.3 μm. The main objective of this work was to investigate and compare the characteristic optical properties of ps lasers based on different Nd-doped laser crystals like Nd:YAG, Nd:YAlO₃, Nd:YVO₄ and Nd:GdVO₄. As a result of these investigations a mode-locked Nd:YVO₄ laser for example, generated, ps pulses at 1.3 μm with a duration of 7 ps, a repetition rate of 160 MHz and an average power of 4.7 W. At 0.9 μm pulses with a duration of 1.9 ps were obtained at a repetition rate of 158 MHz and an average power of 2.8 W. PACS  42.70.Hj; 42.65.Re; 42.65.Ky     

Ablation and analysis of small cell populations and single cells by consecutive laser pulses

Laser ablation of single cells through a sharpened optical fiber is used for the detection of metabolites by laser ablation electrospray ionization (LAESI) mass spectrometry (MS). Ablation of the same Allium cepa epidermal cell by consecutive pulses indicates the rupture of the cell wall by the second shot. Intracellular sucrose heterogeneity is detected by subsequent laser pulses pointing to rupturing the vacuolar membrane by the third exposure. Ion production by bursts of laser pulses shows that the drying of ruptured A. cepa cells occurs in ∼50 s at low pulse rates (10 pulses/s bursts) and significantly faster at high pulse rates (100 pulses/s bursts). These results point to the competing role of cytoplasm ejection and evaporative drying in diminishing the LAESI-MS signal in ∼50 s or 100 laser pulses, whichever occurs first.     

Femtosecond diode laser MOPA system at 920 nm based on asymmetric colliding pulse mode-locking

We report on the generation of 267 fs long pulses with a peak power of 661 W emitted by an InGaAs diode laser master-oscillator power-amplifier (MOPA) system with an external grating compressor. The oscillator emits strongly chirped picosecond pulses with several nanometer of bandwidth, which can be amplified without significant phase modulation and are compressed to femtosecond pulses after leaving the amplifier. We used a diode laser module for asymmetric colliding pulse mode-locking and optimized the collision point and the relative intensity of the counter-propagation pulses.