层状硅酸盐累托石/环氧树脂纳米复合材料的结构和性能研究

用有机改性的层状累托石与环氧树脂复合制备出纳米复合材料 .通过改变累托石含量发现在很低含量 (0 5W % )时纳米复合材料具有最佳力学和热学性能 ,冲击强度增加 12 0 % ,断裂伸长率增加 330 %玻璃化转变温度提高 2 8℃ .用X衍射、透射电镜和红外吸收光谱研究了材料的微观结构 ,结果表明层状累托石和环氧树脂发生了化学反应 ,观测到了层状累托石完全剥离和插层两种结构形态 ,且累托石含量较低时容易形成剥离型 .具有大的比表面积、高的反应活性的累托石片层分散于环氧基体中形成剥离型为主的结构有利于改善复合材料的力学性能并增加其热稳定性 .     

羧甲基壳聚糖/有机累托石纳米复合材料及其药物缓释性能研究

利用简单的溶液插层法制备了羧甲基壳聚糖/有机累托石纳米复合材料,其中累托石(REC)用十六烷基三甲基溴化铵进行改性.用X-射线衍射(XRD)、红外光谱(FTIR)和扫描电镜(SEM)表征了该纳米复合材料的微观结构和形态,实验表明羧甲基壳聚糖插层进入了累托石层间,增大了累托石的层间距,并且累托石均匀地分布在羧甲基壳聚糖基体中.以牛血清蛋白(BSA)为药物模型,研究了纳米复合材料与海藻酸钠形成的微球的药物缓释性能.结果显示,该微球对药物的包封率及缓释性能与纯羧甲基壳聚糖微球相比都有较大改善,包封率从56%提高到86%,药物缓释时间从24 h上升到72 h.并且纳米复合材料/海藻酸钠微球的释药具有pH响应性,在pH为1.2的条件下释药慢,而在pH为7.4时释药快,可用于小肠或结肠定位缓释系统.因此,羧甲基壳聚糖/有机累托石纳米复合材料很有潜力作为药物载体.     

累托石粘土/热塑性聚氨酯弹性体纳米复合材料的研究

采用十二烷基季铵盐合成了一种有机累托石 (ORECA) ,并分别采用不同填充量 2 ,5 ,8份的累托石(REC)及ORECA 与热塑性聚氨酯弹性体 (TPUR)通过熔融共混制备出了粘土 /热塑性聚氨酯弹性体纳米复合材料 ;以红外光谱 (FTIR)、广角X 射线衍射分析 (XRD)、扫描电镜 (SEM)及Molau实验方法研究了REC及ORECA 在TPUR中的分散性 ,研究了复合材料的力学性能 .结果表明 ,ORECA 在质量分数小于 5份时可以和聚氨酯弹性体达到纳米复合 ,复合材料的拉伸强度提高 4 2 % ;撕裂强度在所加份数范围内呈现递增趋势 ,8份时撕裂强度提高 4 9% .     

CdS-TiO2/累托石复合材料的制备及光催化性能

采用原位插层法制备了CdS-TiO2/累托石纳米复合材料. 以X射线粉未衍射、电镜、红外光谱、漫反射吸收光谱及液氮吸附比表面积测定等方法对其微结构和性能进行了分析与表征. 并以罗丹明B(RB)为模拟有机污染物, 对比研究了累托石、TiO2/累托石与CdS-TiO2/累托石的吸附和光催化性能. 结果表明, 与累托石相比, CdS-TiO2/累托石具有更复杂的多孔结构、更大的孔体积和比表面积以及更有效的光吸收能力; 该类复合材料表现出良好的吸附性能和光催化降解活性.     

4,4'-二氨基二苯醚二苯酮固化环氧树脂/粘土纳米复合材料的研究

采用离子交换法, 用十六烷基三甲基溴化铵处理钙基蒙脱土(MMT), 使蒙脱土的层间距由1.49 nm扩大到2.21 nm, 制备了环氧树脂/ BADK/MMT纳米复合材料, 并用XRD等手段研究了有机蒙脱土在环氧树脂中的插层及剥离行为. 研究结果表明, 蒙脱土含量及环氧树脂与有机土的混合温度和时间均对固化后复合材料的剥离产生影响, 只有在特定条件下才能得到剥离型纳米复合材料.     

激光烧结制备尼龙12/累托石纳米复合材料

将有机累托石与尼龙12粉末混合,采用激光烧结(SLS)技术制备了尼龙12累托石纳米复合材料,这是一种使纳米复合材料的制备与材料的成型同时进行的方法.利用X射线衍射(XRD)、红外光谱(FTIR)、扫描电镜(SEM)等手段对复合材料的结构进行了表征,并对其力学性能及热性能进行了研究.结果表明,尼龙12分子在激光烧结过程中插入到累托石层间,形成的复合材料在拉伸强度、弯曲强度、冲击强度等力学性能及热稳定性能方面均优于尼龙12烧结试样.     

累托石/聚丙烯插层纳米复合材料的制备与性能

采用熔融共混法制备了有机改性累托石 (OREC)粘土 均聚聚丙烯 (PP)纳米复合材料 ,以X 射线衍射分析 (XRD)及透射电子显微镜分析 (TEM)观察了复合材料的相貌结构 ,研究了复合材料的力学性能及热性能 .结果表明 ,OREC在添加份数较少时可与均聚聚丙烯熔融插层形成插层型聚丙烯纳米复合材料 ,该复合材料与纯PP相比 ,具有较高的拉伸强度、断裂伸长率及冲击强度 .在有机粘土添加 2 %时 ,复合材料的拉伸强度、断裂伸长率、冲击强度最高 ,与纯PP相比 ,2 %添加量的聚丙烯纳米复合材料拉伸强度提高 6 5 7% ,断裂伸长率提高 2 89 3% ,冲击强度提高 14 1% ,10 %失重率时对应的热分解温度提高 50K .     

累托石粘土/热塑性聚氨酯弹性体纳米复合材料的热性能研究

以十二烷基季铵盐与累托石 (REC)进行阳离子交换得到有机粘土 (OREC) ,以OREC与热塑性聚氨酯弹性体 (TPUR)采用熔融挤出共混法制备了OREC TPUR纳米复合材料 .用透射电子显微镜 (TEM)表征了复合材料的微相结构 ,测试了复合材料动态热机械性能 (DMA)及热失重 (TG) ,讨论了复合材料的耐热空气老化性能及耐油介质性能等 .结果表明 ,累托石粘土在聚氨酯热塑性弹性体中以纳米尺寸分散 ,纳米复合材料具有较高的动态热机械性能 ,其储能模量最大可提高 7倍多 ,损耗模量最大可提高 4倍多 .复合材料的其他性能均有不同程度的提高 ,特别是OREC添加量为 2 %时 ,复合材料TG、耐油性及耐空气老化性能最高 .其初始分解温度提高 1 5℃ ,在 40 #机油中浸泡 1 68h后拉伸强度保持率达到 86 4% ,1 2 0℃热空气老化箱中老化 72h后拉伸强度保持率达到 87 0 % .     

双单体原位接枝插层法制备聚丙烯纳米复合材料的研究Ⅰ.制备、表征及力学性能的研究

用有机插层剂处理蒙脱土原土 ,制得有机蒙脱土 (O MMT) .采用双单体 (马来酸酐和苯乙烯 )原位接枝插层法 ,制备了聚丙烯 蒙脱土纳米复合材料母料 .将母料与聚丙烯基体在双螺杆上共混挤出 ,制得聚丙烯 蒙脱土纳米复合材料 (PP Montmorillonetenanocomposites,PMNC) .这是制备聚合物纳米复合材料的一种新方法 .通过X 射线衍射测试 (XRD)表明 ,有机蒙脱土片层 0 0 1面间距从原土的 1 4 9nm扩大到 2 96nm ,复合材料中蒙脱土片层 0 0 1面间距由有机蒙脱土的 2 96nm扩大到 4 0nm .力学性能测试表明 ,复合材料的力学性能明显优于PP基体 ,在提高材料拉伸强度的同时 ,缺口冲击强度也得到很大的提高 .用扫描电镜 (SEM)对材料的冲击断面形貌进行了研究 ,并从理论上分析了断裂机理 .随着蒙脱土含量的增加 ,冲击断裂形式逐渐从脆性断裂变成韧性断裂     

基于氟碳表面活性剂插层水滑石的聚酰亚胺纳米复合材料的制备与性能

以氟碳表面活性剂全氟辛基磺酸钾为插层剂, 通过离子交换制备插层水滑石, 并以其为填料, 通过原位插层聚合方法, 制备了水滑石/氟碳表面活性剂/聚酰亚胺纳米复合材料. 用X射线衍射、 红外光谱和热失重等方法分析插层水滑石结构. 结果表明, 全氟辛基磺酸钾插层水滑石后, 水滑石的层间距由0.76 nm增加到2.52 nm, 在水滑石层间构建了氟碳链的微环境. 这种氟化水滑石可剥离分散于聚酰亚胺基体中, 改善了纳米复合材料的气体阻隔性能、 介电性能和机械性能. 这种影响不仅体现无机纳米片层的杂化效果, 而且展示出氟碳链的特点.     

Microstructure of polymer–clay nanocomposites studied by positrons

The epoxy–rectorite nanocomposites with different rectorite contents, epoxide equivalent were prepared and its microstructure was studied by positron annihilation and X-ray diffraction (XRD). At low rectorite content (0–2.0%), the free volume size in nanocomposites is nearly the same, but its concentration decreases with increasing content; the exfoliated structure was observed by XRD and interfacial layer formation between rectorite platelets and epoxy matrix was probed by positrons. Comparing with epoxy–montmorillonite, the exfoliated structure and interfacial layers are easier formed in epoxy–rectorite nanocomposites.     

Surface modification of montmorillonite on surface Acid-base characteristics of clay and thermal stability of epoxy/clay nanocomposites

In this work, the effect of surface treatments on smectitic clay was investigated in surface energetics and thermal behaviors of epoxy/clay nanocomposites. The pH values, X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FT-IR) were used to analyze the effect of cation exchange on clay surface and the exfoliation phenomenon of clay interlayer. The surface energetics of clay and thermal properties of epoxy/clay nanocomposites were investigated in contact angles and thermogravimetric analysis (TGA), respectively. From the experimental results, the surface modification of clay by dodecylammonium chloride led to the increases in both distance between silicate layers of about 8 A and surface acid values, as well as in the electron acceptor component (gamma(+)(s)) of surface free energy, resulting in improved interfacial adhesion between basic (or electron donor) epoxy resins and acidic (electron acceptor) clay interlayers. Also, the thermal stability of nanocomposites was highly superior to pure epoxy resin due to the presence of the well-dispersed clay nanolayer, which has a barrier property in a composite system.     

Layered silicate/epoxy nanocomposites: synthesis,characterization and properties

Novel epoxy‐clay nanocomposites have been prepared by epoxy and organoclays. Polyoxypropylene triamine (Jeffamine T‐403), primary polyethertriamine (Jeffamine T‐5000) and three types of polyoxypropylene diamine (Jeffamine D‐230, D‐400, D‐2000) with different molecular weight were used to treat Na‐montmorillonite (MMT) to form organoclays. The preparation involves the ion exchange of Na⁺ in MMT with the organic ammonium group in Jeffamine compounds. X‐ray diffraction (XRD) confirms the intercalation of these organic moieties to form Jeffamine‐MMT intercalates. Jeffamine D‐230 was used as a swelling agent for the organoclay and curing agent. It was established that the d₀₀₁ spacing of MMT in epoxy‐clay nanocomposites depends on the silicate modification. Although XRD data did not show any apparent order of the clay layers in the T5000‐MMT/epoxy nanocomposite, transmission electron microscopy (TEM) revealed the presence of multiplets with an average size of 5 nm and the average spacing between multiplets falls in the range of 100 Å. The multiplets clustered into mineral rich domains with an average size of 140 nm. Scanning electron microscopy (SEM) reveals the absence of mineral aggregate. Nanocomposites exhibit significant increase in thermal stability in comparison to the original epoxy. The effect of the organoclay on the hardness and toughness properties of crosslinked polymer matrix was studied. The hardness of all the resulting materials was enhanced with the inclusion of organoclay. A three‐fold increase in the energy required for breaking the test specimen was found for T5000‐MMT/epoxy containing 7 wt% of organoclay as compared to that of pure epoxy. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation of highly exfoliated epoxy/clay nanocomposites by clay grafted with liquid crystalline epoxy

Epoxy/clay nanocomposites with a high degree of exfoliation were achieved by intercalating liquid crystalline epoxy into clay intragallery as well as using a so-called ‘solution compounding’ process. In this process, clay modified was first treated with trichloromethane to form organoclay-trichloromethane suspension followed by liquid crystalline epoxy modification. The liquid crystalline epoxy grafted clay was then mixed extensively with epoxy to form epoxy/nanoclay composites. The mechanism of exfoliation was explored by monitoring the change of morphology of organoclay during each stage of processing with X-ray diffraction (XRD). The liquid crystalline epoxy grafted clay synthesised was characterised by fourier transform infrared spectroscopy (FT-IR) and polarising optical microscopy (POM). The clay platelets uniformly dispersed and highly exfoliated in the whole epoxy matrix were observed using transmission electron microscopy (TEM) and FT-IR imaging system. The epoxy nanocomposites were fabricated by incorporating different liquid crystalline epoxy grafted clay loading. The results revealed that the incorporation of liquid crystalline epoxy grafted clay resulted in a significant improvement in glass transition temperature (Tg) derived from dynamic mechanical analysis (DMA) and thermal stability measured by thermogravimetric analysis (TGA).     

Preparation,swelling, and stimuli‐responsive characteristics of superabsorbent nanocomposites based on carboxymethyl cellulose and rectorite

Utilization of naturally available raw materials for the fabrication of eco‐friendly functional materials has long been desired. In this work, a series of superabsorbent nanocomposites were prepared by radical solution copolymerization of sodium carboxymethyl cellulose (CMC), partially neutralized acrylic acid (NaA), and rectorite (REC) in the presence of initiator ammonium persulfate (APS) and crosslinker N,N'‐methylene‐bis‐acrylamide (MBA). The optimal reaction variables including the mass ratio of acrylic acid (AA) to CMC, MBA concentration, and REC content were explored. FTIR spectra confirmed that NaA had been grafted onto CMC and REC participated in polymerization. REC was exfoliated and uniformly dispersed in the CMC‐g‐PNaA matrix without agglomeration as shown by XRD, TEM, and SEM analysis. The thermal stability, swelling capabilities, and rate of the nanocomposites were improved after introducing REC, and the gel strength greatly depended on the concentration of crosslinker MBA. The nanocomposite showed excellent responsive properties and reversible On–Off switching characteristics in various saline, pH, and hydrophilic organic solvent/water solutions, which provided great possibility to extend the application domain of the superabsorbent nanocomposites such as drug delivery system. Copyright © 2010 John Wiley & Sons, Ltd.     

木质纤维素-蒙脱土纳米复合材料的制备

采用插层复合方法在碱性水溶液中制备了木质纤维素-蒙脱土纳米复合材料,并分析了反应温度、反应时间、木质纤维素与蒙脱土的质量比等因素对纳米复合材料有机化程度的影响,用FT-IR、XRD、TEM、SEM等方法对纳米复合材料的结构进行了表征。结果表明:蒙脱土片层结构在反应过程中被撑开,木质纤维素分散在其中,形成插层-剥离型纳米复合材料,其热稳定性较木质纤维素有了较大提高。     

Effect of epoxy resin on rheology of polycarbonate/clay nanocomposites

Polycarbonate/clay nanocomposites (PCNs) were prepared by melt intercalation using epoxy resin as a compatibilizer. The intercalated structure of PCNs was investigated using XRD and TEM. The linear and nonlinear dynamic rheological properties of PCNs were measured by the use of a parallel plate rheometer. The results reveal that the presence of epoxy influences rheological behavior of PCNs significantly. Addition of epoxy can improve dispersion of clay, enhancing the low-frequency viscoelastic responses; while high loadings of epoxy lead to a severe degradation of PC matrix, decreasing the high-frequency responses together with the plasticizing effect of excessive epoxy. Both of these two effects result in invalidity of time-temperature superposition. Moreover, all samples show high sensitivity to both the quiescent and large amplitude oscillatory shear (LAOS) deformation, despite enhanced percolation of tactoids due to the compatibilization of epoxy.