Determination of traces molybdenum by catalytic adsorptive stripping voltammetry

A reliable and very sensitive procedure for the determination of ultra trace of molybdenum is proposed. Molybdenum was determined by cathodic stripping differential pulse voltammetry based on the adsorption collection of the Mo(VI)-Tiron complex on a hanging mercury drop electrode (HMDE). The variation of peak current with pH, concentration of Tiron and chlorate, plus several instrumental parameters such as accumulation time, accumulation potential and scan rate, were optimized. Under optimized condition, the relationship between the peak current and molybdenum concentration is linear in the range of 0.010-21.0 ng ml⁻¹. The limit of detection was found to be 0.006 ng ml⁻¹. The relative standard deviation for 10 replicates determination of 0.6 and 10 ng ml⁻¹ Mo(VI) is equal to 1.3 and 0.9%, respectively. The method was applied to the determination of molybdenum in river water, tap water, well water, plant foodstuff samples such as cucumber, tomato, carrot, and certified steel reference materials.     

Trace determination of molybdenum by adsorptive cathodic stripping voltammetry

Molybdenum is determined by adsorptive cathodic stripping voltammetry in 0.15 M nitric acid solution containing 15 μM 2′,3,4′,5,7-pentahydroxyflavone (morin) as a ligand. In this medium, molybdenum is preconcentrated on a hanging mercury drop electrode and stripped cathodically in square-wave voltammetry mode, with a peak potential of -350 mV vs. Ag/AgCl (saturated KCl). The effect of various parameters (ligand concentration, supporting electrolyte composition, accumulation potential and collection time) on the sensitivity and linear range of the calibration curve are discussed. With controlled accumulation for 1 min, the detection limit (3σ) was 0.45 ng ml^?1 molybdenum and the calibration curve is linear up to 70 ng ml^?1. The procedure is applied to the determination of molybdenum in real samples with satisfactory results.     

Determination of uranium by adsorptive stripping voltammetry

A voltammetric method for the determination of uranium in natural waters in the concentration range from 0.4 μg 1⁻¹ to 0.2 mg 1⁻¹ is described. The method is based on adsorptive accumulation of the uranium(VI)—pyrocatechol complex on the hanging mercury drop electrode followed by the reduction of the absorbed complex.     

Determination of palladium by adsorptive stripping voltammetry

 Adsorptive accumulation of the Pd(II) complex with dimethylglyoxime was evaluated for stripping voltammetry with respect to different parameters. The sensitivity of the method and the linearity between the peak current and the concentration of Pd(II) depends on the ionic strength, the electrode area, the preconcentration time, the transport rate to the electrode, and the potential scan rate. The most appropriate medium was 0.1 mol/L acetate buffer between pH 3.5 and 4. Using 2 min of preconcentration at a 2.6 mm² electrode and the differential pulse mode, a detection limit of 0.05 μg/L Pd was achieved for liquid samples and 50 ng/g for solid samples. Different aqueous and solid samples were analysed and the recovery from biological and inorganic materials investigated. Received: 29 February 1996/Revised: 29 July 1996/Accepted: 1 August 1996     

Determination of azinphos-methyl by adsorptive stripping voltammetry

A very sensitive electrochemical stripping procedure for azinphos-methyl (Guthion) is reported. Accumulation is achieved by adsorption of the compound on a hanging mercury drop electrode. The adsorptive stripping response was evaluated with respect to accumulation time and potential, concentration dependence, electrolyte and other variables. The determination limit is 0.2 ng ml^?1 after 300 s accumulation and 0.4 ng ml^?1 after 180 s accumulation. The procedure was applied to spiked river water.     

Determination of trichlorobiphenyl by adsorptive stripping voltammetry

Trichlorobiphenyl is determined in the concentration range 0.004–1 mg l^?1 by adsorptive stripping voltammetry at a hanging mercury drop electrode. Preconcentration is achieved by adsorption at a potential of ?0.40 (V (vs. Ag/AgCl), and desorption at ?1.10 V. Biphenyl interferes with the determination only when present in 5-fold molar amounts compared to trichlorophenyl. The interference of DDT is eliminated by prior treatment of the sample solution with sulphuric acid. The method was applied for the analysis of waste and natural waters, the relative standard deviation being <5%.     

Determination of gallium by adsorptive stripping voltammetry

A procedure for the determination of gallium by differential pulse adsorptive stripping voltammetry (DPADSV), using different complexing agents (ammonium pyrrolidine dithiocarbamate (APDC), pyrocatechol violet (PCV) and diethyldithiocarbamate (DDTC)), has been optimized. The selection of the experimental conditions was made using experimental design methodology. Under these conditions, the calibration was made and the detection limit was determined for each gallium-ligand complex. A robust regression method was applied which allowed the elimination of anomalous points. The detection limit, with α=β=0.05, for gallium-APDC complex was 5.0×10⁻⁸ mol dm⁻³, for gallium-PCV complex was 9.9×10⁻⁹ mol dm⁻³, and the lowest detection limit (1.3×10⁻⁹ mol dm⁻³) was obtained with DDTC. For this reason, DDTC was selected for the determination of the gallium concentration in a certificate sample and in a spiked tap water sample. The linear dynamic range for gallium-APDC complex was from 5.0×10⁻⁸ to 2.7×10⁻⁷ mol dm⁻³, for gallium-PCV complex was from 5.0×10⁻⁹ to 4.8×10⁻⁷ mol dm⁻³, and for gallium-DDTC complex was from 1.0×10⁻⁹ to 2.1×10⁻⁷ mol dm⁻³.     

Determination of alprazolam in serum by adsorptive stripping voltammetry

The surface-active properties of alprazolam at a hanging mercury drop electrode allow their sensitive determination by differential-pulse adsorptive stripping voltammetry. Detection limits are 0.07 ng/ml for accumulation in water (accumulation time 240 s) and 0.3 ng/ml for accumulation in serum extract (accumulation time 30 s). Coefficients of variation at 5 ng/ml (10 determinations) were typically <2%.     

Determination of secnidazole in urine by adsorptive stripping voltammetry

Cyclic voltammetry was used to explore the adsorption behavior of secnidazole on a hanging mercury drop electrode (HMDE). The effects of various operational parameters on the accumulation behavior of the adsorbed species were tested. Thus, a sensitive stripping voltammetry procedure for the determination of secnidazole with an adsorptive accumulation on the surface of HMDE has been developed. Measurements were taken by differential-pulse voltammetry after determination of the optimum conditions. The linear concentration range was 1 x 10(-8)-1 x 10(-7) s when using a 120 s preconcentration at -0.1 V vs. Ag/AgCl in acetate buffer of pH 4.0. The detection limit of secnidazole was 5 x 10(-9) M. The precision, expressed by the coefficient of variation, was 2.5% (n = 10) at a concentration of 1 x 10(-7) m. The method was successfully applied to the analysis of secnidazole in urine.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily     

Determination of the antibacterial enrofloxacin by differential-pulse adsorptive stripping voltammetry

Two new methods for the determination of enrofloxacin in commercial formulations and canine urine samples, based on adsorptive stripping voltammetry (AdSV), are proposed. One of the proposed method uses univariate calibration to analyse enrofloxacin in commercial formulations and the other applies principal component regression (PCR) to the voltammetric measurements to determine enrofloxacin in the presence of its metabolite ciprofloxacin. The linear concentration ranges of application were 4-25 and 18-55 ng ml⁻¹ by using an accumulation potential of −0.3 V and a 180 or 60 s accumulation time, respectively for the univariate method. The first concentration range was used for the multivariate method. Both methods were successfully applied to the analysis of commercial formulations and spiked canine urine samples, respectively.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily Received: 10 July 1997 / Revised: 1 April 1998 / Accepted: 6 April 1998     

Determination of uranium by adsorptive stripping voltammetry at a lead film electrode

An adsorptive stripping voltammetric procedure for the determination of U(VI) at an in situ plated lead film electrode is described. The U(VI) complex with cupferron was accumulated from an acetate buffer solution of pH 4.2 at the potential −0.65 V. The measurements were carried out from undeaerated solutions. The calibration graph for an accumulation time of 180 s was linear from 5 × 10⁻¹⁰ to 2 × 10⁻⁸ mol L⁻¹. The detection limit was 2 × 10⁻¹⁰ mol L⁻¹, the relative standard deviation for 2 × 10⁻⁸ mol L⁻¹ U(VI) was 4.3%. The proposed procedure was validated in the course of U(VI) determination in water certified reference materials.     

Determination of aluminium in tree samples by cathodic adsorptive stripping voltammetry

This paper presents a method of determination of aluminium in tree samples (wood, leaves, roots) based on the cathodic adsorptive stripping voltammetry. Al(III) complexed with alizarin S was determined by ASV method using a hanging mercury drop electrode. Optimal conditions were found to be: accumulation time 30-90 s, accumulation potential - 0.70 V versus SCE, supporting electrolyte 0.1 M ammonia-ammonium chloride buffer at pH 8.2 and concentration of alizarin 1 x 10(-5) M. The response of the system, a linear current-concentration relationship was observed up to 8 x 10(-6) M. The developed method has been tested by analysing international reference materials (BCR 62 Olive leaves and BCR 101 spruce needles).     

Determination of dinoseb by adsorptive stripping voltammetry using a mercury film electrode

An adsorptive stripping voltammetric method for the determination of the pesticide dinoseb (2-sec.-butyl-4,6-dinitrophenol) at the mercury film electrode is described. The deposition of the mercury film on a glassy carbon disk electrode was optimized. The temperature, at which the mercury film was deposited, was demonstrated to have a strong influence on the stripping peaks, the first one being much more intense than the second. A systematic study of the variables affecting the stripping response was carried out by differential pulse voltammetry. The results obtained have been compared with those at the HMDE; a significant improvement in the sensitivity of the method developed with the MFE was observed. Using a 300 s accumulation time, the limits of determination and detection were 3.6 × 10^–10 and 1.1 × 10^–10 mol L^–1, respectively. The effect of the presence of several herbicides on the dinoseb response was also tested. The method has been applied to the determination of the pesticide in spiked apple juice at two concentration levels: 12.0 and 1.2 g L^–1 of juice.     

Determination of methotrexate in human blood plasma by adsorptive stripping voltammetry

The use of adsorptive stripping voltammetry to measure sub-micromolar concentrations of methotrexate in plasma has been investigated. A simple clean-up procedure has been developed in which methotrexate is extracted from blood plasma with Amberlite XAD-2, which is a non-ionic resin, and eluted with methanol. Recovery for plasma analysis was 80%.     

Determination of selenium in sea water by adsorptive cathodic stripping voltammetry

A procedure is presented for determining Se(IV) and total dissolved Se in sea water using cathodic stripping voltammetry in the presence of added copper. Experiments using cyclic voltammetry indicate that the preconcentration step consists in adsorption of a Cu(I)₂Se complex species on the hanging mercury drop electrode. The optimized analytical conditions include a copper concentration of 40 μM and a solution pH of 1.6. Differential pulse modulation is used. Interference caused by organic surface-active substances present in natural waters in eliminated by UV photolysis of the sample. Cadmium interferes with the determination of Se only when present at a concentration 100 times higher than normal. UV photolysis at pH ≈ 8 is used to convert Se(VI), which is the electroactive species. The response is linear for Se concentrations between 0 and 200 nM. The limit of detection is 0.01 nM Se when a deposition time of 15 min is used.     

Determination of cobalt by adsorptive stripping voltammetry with double accumulation and stripping steps

A double accumulation and stripping steps were proposed to increase the sensitivity of Co(II) determination by catalytic adsorptive stripping voltammetry (AdSV). Electrodes with large and small surface area were used for the first and second accumulation step, respectively. As the accumulation of Co(II) complex at the first electrode was finished, the electrode was placed at a short distance opposite the second one. Then the Co(II) complex desorbed from the first electrode was accumulated at the second electrode. Taking into account the small volume of space between the electrodes, the concentration of the Co(II) complex in solution between the electrodes was drastically higher than that in the bulk solution. The accumulation step at the second electrode was performed from the solution with higher concentration of Co(II) and therefore the detection limit was lowered. The calibration graph of Co(II) determination for accumulation time of 120 s at both electrodes was linear from 1.18 to 58.9 ng L^?1. The detection limit for Co(II) was equal to 0.47 ng L^?1 and it is so far the lowest detection limit obtained for Co(II) using mercury-free electrodes. The proposed method was applied to Co(II) determination in water certified reference material.     

Determination of ceftriaxone in biological material by differential-pulse adsorptive stripping voltammetry

Differential-pulse adsorptive stripping voltammetry was used to determine sub-micromolar concentrations of ceftriaxone in plasma. A hanging mercury drop electrode was chosen as the working electrode. A simple clean-up procedure was developed in which ceftriaxone was extracted from blood plasma with the non-ionic resin Amberlite XAD-2 and eluted with methanol. The recovery from plasma was 97.6% using a 1.52 x 10(-4) M stock ceftriaxone solution. The method was applied to caesarean cases, and total ceftriaxone levels were measured in the maternal and umbilical cord blood. The amount of ceftriaxone transmitted to the baby on administration of the drug to the mother before the caesarean operation was found to be in the range 0.067-0.17%.