Preparation of Highly Active Pt-K/γ-Al2O3 Catalyst for o-Phenylphenol Synthesis from o-Cyclohexenyl-cyclohexanone Dehydrogenation

0.5%Pt-K/γ-Al2O3 catalysts for the synthesis of o-phenylphenol（OPP） from o-cyclohexenyl-cyclohexanone （dimer） dehydrogenation were prepared by means of a two subsequent impregnation method. The effects of catalyst preparation parameters, such as K promoters, calcination, and reduction conditions, were investigated. The results showed that the addition of K2SO4 to Pt/γ-Al2O3 catalyst notably promoted the selectivity of OPP, and its optimum content was found to be 6% in mass fraction. The higher activity was obtained when Pt/γ-Al2O3 catalyst was calcined in nitrogen atmosphere at 400--500 ℃ and then reduced at the same temperature for 3 h in hydrogen atmosphere. The conversion of the dimer and the selectivity of OPP were always above 99% and 90%, respectively, over 0.5%Pt-6% K2SO4/γ-Al2O3 catalyst during the pilot scale test of 8000 h.     

In situ carbon nanotube synthesis by the reduction of NiO/γ-Al2O3 catalyst in methane

The synthesis of carbon nanotubes (CNTs) via chemical vapour deposition of methane on NiO/γ-Al2O3 catalyst has been investigated. The reduction behavior of NiO/γ-Al2O3 by methane was studied using thermogravimetric (TG) and X-ray diffraction (XRD) techniques. It was found that the NiO supported on γ-Al2O3, was reduced to Ni⁰ in methane atmosphere in the temperature range of 710--770 ℃. The catalytic activity of NiO/γ-Al2O3 for CNTs synthesis by in situ chemical vapour deposition of methane during the reduction was also investigated. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to observe the CNTs produced at various reduction temperatures. The results indicated that the reduction temperature exhibits obvious influence on the morphology and the yield of CNTs. CNTs with the diameter of about 20 nm were obtained at reduction temperature of 750 ℃, and higher reduction temperature (such as 800 and 850 ℃) led to an increase in CNTs diameter and a decrease in CNTs yield.     

Effect of CeO2 addition on Ni/Al2O3 catalysts for methanation of carbon dioxide with hydrogen

The Ni-CeO2/Al2O3 catalysts with a nickel content of 15 wt% prepared via impregnating boehmite were found to be highly active and stable for methanation of carbon dioxide with hydrogen at a H2/CO2 molar ratio of 4.The effects of CeO2 content and reaction temperature on the performance of the Ni-CeO2/Al2O3 catalysts were studied in detail.The results showed that the catalytic performance was strongly dependent on the CeO2 content in Ni-CeO2/Al2O3 catalysts and that the catalysts with 2 wt%CeO2 had the highest catalytic activity among the tested ones at 350℃.The XRD and H2-TPR characterizations revealed that the addition of CeO2 decreased the reduction temperature by altering the interaction between Ni and Al2O3,and improved the reducibility of the catalyst.Preliminary stability test of 120 h on stream over the Ni-2CeO2/Al2O3 catalyst at 350℃ revealed that the catalyst was much better than the unpromoted one.     

Thermal decomposition and cobalt species transformation of carbon nanotubes supported cobalt catalyst for Fischer-Tropsch synthesis

The effect of calcination condition on the cobalt species and Fischer-Tropsch synthesis (FTS) was studied. It was found that higher calcination temperature resulted in decreased FTS activities because CNTs were consumed by oxidation in air at temperature higher than 230°C. Cobalt species went through transformation from Co3O4 to metallic Co in Ar by autoreduction at temperature over 500°C. The autoreduction route might be Co3O4→CoO→Co or Co3O4→Co2C→Co. Reduction at temperature higher than 500°C also resulted in decreased FTS activities due to the methanation of CNTs in hydrogen.     

Effects of pretreatment and reduction on the Co/Al2O3 catalyst for CO hydrogenation

The purpose of this study was to investigate the effect of preadsorbed CO at different temperatures, calcination temperatures, the combined influence of reduction temperature and time, and pretreatment using hydrogen or syngas as reduction agents on the F-T synthesis （FTS） activity and selectivity of Co/Al2O3 catalyst. The reactivity of the carbon species at higher preadsorption temperature with H2 in TPSR decreased, whereas the carbon-containing species showed higher reactivity over Co/Al2O3 catalyst with low calcination temperature. This agreed well with the order of catalytic activity for F-T synthesis on this catalyst. The catalytic activity of the catalyst varied with reduction temperature and time remarkably. CODEX optimization gave an optimum reduction temperature of 756 K and reduction time of 6.2 h and estimated C5＋ yield perfectly. The pretreatment of Co/Al2O3 catalyst with different reduction agents （hydrogen or syngas） showed important influences on the catalytic performance. A high CO conversion and C5＋ yield were obtained on the catalyst reduced by hydrogen, whereas methane selectivity on the catalyst reduced by syngas was much higher than that on the catalyst reduced by hydrogen.     

LiOH-LiNO3低共熔混合锂盐体系合成LiNi1/3Co1/3Mn1/3O2

The powder of LiNi1/3Co1/3Mn1/3O2 were prepared directly without artificial grinding and washing by a eutectic molten-salt mixture (0.38LiOH·H2O-0.62LiNO3) method. According to this method, the eutectic molten-salt mixture was self-mixed with precursor thoroughly at low temperature, and then sintered at a certain temperature. The tap-density of the powder obtained was 2.87 g·cm-3. The well-layered 琢-NaFeO2 structure and regular morphology were confirmed by X-ray diffraction (XRD) and scanning electronmicroscopy (SEM).XPSstudies showed that the predominant oxidation states of Ni, Co, andMn in the compound were 2+, 3+, and 4+, respectively. Cathodic behaviour was examined by charge-discharge cycling. The synthesized powder showed a reversible capacity of 160 mAh·g -1 at a specific current of 0.2C in the rang 3.0-4.3 V up to 50 cycles without noticeable capacity-fading.     

THERMAL-SENSITIVE BETA-CYCLODEXTRIN-CONTAINED POLY(N-ISOPROPYLACRYLAMIDE) HYDROGELS CROSS-LINKED BY Si―O―Si BONDS

A series of novel p（N-isopropylacrylamide） （PNIPAM） hydrogels were synthesized by radical copolymerization of N-isopropylacrylamide （NIPAM） and 3-methacryloxypropyltrimethoxysilane （MPTMS）. The copolymers were then crosslinked through hydrolysis of the siloxane in acetic acid/water mixed solvent. Beta-cyclodextrin （Beta-CD） was introduced into the polymeric networks by condensation of 3-glycidoxypropyltrimethoxysilane derived beta-cyclodextrin （KH560-beta-CD） with MPTMS under acidic condition. These gels were heterogeneous, porous and exhibited fast deswelling kinetics when the temperature was elevated to above lower critical solution temperature （LCST）. The swelling ratios of the gels containing beta-CD at room temperature were higher than that of the normal PNIPAM hydrogel, which was caused by the lower crosslinking density in beta-CD contained gels. In comparison to that of the normal PNIPAM gel, the amount of loaded-drug in the hydrogel containing beta-CD was higher, and the release time of 5-fluorouracil （5-Fu） was prolonged, which was attributed to the formation of inclusion compounds between 5-Fu and beta-CD in gel network.     

CO2重整甲烷制合成气催化剂六铝酸盐LaNiy/Al12-yO19-δ的研究

A series of Ni modified hexaaluminates LaNi y Al 12- y O 19- δ ( y =0 3, 0 6, 0 9, 1 0) were prepared by decomposition of nitrates and calcination at high temperature. The crystalline structure and catalytic properties for CO 2 reforming of methane to synthesis gas were investigated by using XRD, XPS, TPR and TGA techniques. The results showed that a pure hexaaluminate LaNi y Al 12- y O 19- δ phase is formed only when y value is in 0< y ≤1. The reduced hexaaluminates LaNi y Al 12- y O 19- δ exhibit significant catalytic activity and stability for the reaction of CO 2 reforming of methane to synthesis gas at 780 ℃, and no deactivation resulting from carbon deposition is found. In the meantime, the catalytic activity is obviously affected by the modifier Ni in the hexaaluminate lattices. Under the same reaction conditions, the conversion of CH 4 and CO 2 increase with increase in the amount ( y value) of the modifier Ni.     

Highly selective synthesis of 3-methylindole from glycerol and aniline over Cu/NaY modified by K2O

The vapor-phase synthesis of 3-methylindole from glycerol and aniline over Cu/NaY modified by K2O was investigated. The catalysts were characterized by X-ray diffraction （XRD） and the temperature- programmed desorption of ammonia （NH3-TPD）. The effect of the reaction temperature on the activity and selectivity of Cu]NaY-K2O catalyst was also investigated. The results indicated that the addition of K2O to Cu/NaY increased the selectivity of the catalyst remarkably because the amount of middle-strong acid sites decreased clearly. The decrease of the reaction temperature was beneficial for the increase of 3- methylindole selectivity. Over Cu/NaY-K2O, the selectivity of 3-methylindole reached 75% and the yield of the target product was up to 47% at 220 ℃. A probable catalytic mechanism for the synthesis of 3- methylindole from glycerol and aniline was proposed.     

In situ carbon nanotube synthesis by the reduction of NiO/γ-Al_2O_3 catalyst in methane

The synthesis of carbon nanotubes (CNTs) via chemical vapour deposition of methane on NiO/γ-Al2O3 catalyst has been investigated.The reduction behavior of NiO/γ-Al2O3 by methane was studied using thermogravimetric (TG) and X-ray diffraction (XRD) techniques.It was found that the NiO supported on γ-Al2O3,was reduced to Ni0 in methane atmosphere in the temperature range of 710-770℃.The catalytic activity of NiO/γ-Al2O3 for CNTs synthesis by in situ chemical vapour deposition of methane during the reduction was also investigated.Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to observe the CNTs produced at various reduction temperatures.The results indicated that the reduction temperature exhibits obvious influence on the morphology and the yield of CNTs.CNTs with the diameter of about 20 nm were obtained at reduction temperature of 750℃,and higher reduction temperature (such as 800 and 850℃) led to an increase in CNTs diameter and a decrease in CNTs yield.     

Site‐Specific Substitution Preferences in the Solid Solutions Li12Si7–xGex,Li12–yNaySi7, Na7LiSi8–zGez,and Li3NaSi6–vGev

The mixed silicide‐germanides Li₁₂Si_7–xGe_x, Na₇LiSi_8–zGe_z, and Li₃NaSi_6–vGe_v which could serve as potential precursors for Si_1–xGe_x materials were synthesized and characterized by X‐ray diffraction methods. The full solid solution series Li₁₂Si_7–xGe_x (0 ≤ x ≤ 7) is easily accessible from the elements and features preferential occupation of the more negatively charged crystallographic tetrel positions by Ge, which is the more electronegative element. In case of Na₇LiSi_8–zGe_z a broad solid solution range of 1.3 ≤ x ≤ 8 is available but the ternary silicide Na₇LiSi₈ could not be obtained by the tested methods of synthesis. The solubility of Ge in Li₃NaSi_6–vGe_v is highly limited to a maximum of v ≈ 0.5, and again the formally more negatively charged tetrel positions are preferred by Ge. Additionally, the two crystallographic Li positions in Li₁₂Si₇ with unusually large displacement parameters can be partially substituted by Na in Li_12–yNa_ySi₇ with 0 ≤ y ≤ 0.6. The statistical mixing of Li and Na in this solid solution contrasts the typical ordering of Li and Na in most ternary tetrelides.     

Effect of Li2O Addition on the Preparation of (Y2‐yLiy)Ti2O7‐y

A new series of (Y_2‐yLi_y)Ti₂O_7‐y having an ordered pyrochlore phase was prepared by a solid state reaction method with a solid solution range of 0.05 ≥ y ≥ 0.10. Unit cell parameters obtained by the Rietveld refinement method shows that the a‐axis decreases linearly with increasing the amount of Li ion addition, indicating the successful incorporation of the Li ion into unit cell. The average x‐fractional coordinate of the O(1) site depends on the ionic radius ratio of r(A³+)/r(Ti⁴⁺) in the A₂Ti₂O₇ with a pyrochlore phase. The Ti K‐edge XANES spectra of the (Y_2‐yLi_y)Ti₂O_7‐y show that the valence of the Ti ions is slightly less than 4 so that Ti is in the mixed valence state. Average particle size increases with increasing the amount of extra Li ion addition, which acts as a flux to lower the melting point of the materials.     

Neue Vertreter des Er6[Si11N20]O‐Strukturtyps Hochtemperatur‐Synthesen und Kristallstrukturen von Ln(6+x/3)[Si(11–y)AlyN(20+x–y)]O(1–x+y) mit Ln = Nd,Er, Yb,Dy und 0 ≤ x ≤ 3, 0 ≤ y ≤ 3

New Representatives of the Er₆[Si₁₁N₂₀]O Structure Type. High‐Temperature Synthesis and Single‐Crystal Structure Refinement of Ln_(6+x/3)[Si_(11–y)Al_yN_(20+x–y)]O_(1–x+y) with Ln = Nd, Er, Yb, Dy and 0 ≤ x ≤ 3, 0 ≤ y ≤ 3 According to the general formula Ln_(6+x/3)[Si_(11–y)Al_yN_(20+x–y)]O_(1–x+y) (0 ≤ x ≤ 3, 0 ≤ y ≤ 3) four nitridosilicates, namely Er₆[Si₁₁N₂₀]O, Yb_6.081[Si₁₁N_20.234]O_0.757, Dy_0.33Sm₆[Si₁₁N₂₀]N, and Nd₇[Si₈Al₃N₂₀]O were synthesized in a radiofrequency furnace at temperatures between 1300 and 1650 °C. The homeotypic crystal structures of all four compounds were determined by single‐crystal X‐ray diffraction. The nitridosilicates are trigonal with the following lattice constants: Er₆[Si₁₁N₂₀]O: a = 978.8(4) pm, c = 1058.8(3) pm; Yb_6.081[Si₁₁N_20.243]O_0.757: a = 974.9(1) pm, c = 1055.7(2) pm; Dy_0.33Sm₆[Si₁₁N₂₀]N: a = 989.8(1) pm, c = 1078.7(1) pm; Nd₇[Si₈Al₃N₂₀]O: a = 1004.25(9) pm, c = 1095.03(12) pm. The crystal structures were solved and refined in the space group P31c with Z = 2. The compounds contain three‐dimensional networks built up by corner sharing SiN₄ and AlN₄ tetrahedra, respectively. The Ln³⁺ and the “isolated” O^2– ions are situated in the voids of the structures. According to Ln_(6+x/3)[Si_(11–y)Al_yN_(20+x–y)]O_(1–x+y) an extension of the Er₆[Si₁₁N₂₀]O structure type has been found.     

Synthesis and Electrochemical Performance of Ti 4＋ Doped LiV 3O 8

溶胶凝胶法合成了层状的LiTiyV3-0.8yO8（y=0, 0.04, 0.06, 0.08）正极材料,这些材料因为掺杂Ti量的不同,而具有了不同的形貌特征（形状,粒径,比表面积）以及电化学性质（首次充放电容量, 循环容量等）。XRD,SEM, CV,及充放电测试对该正极材料的结构和电化学性能进行了表征,结果表明当y=0.04时,该正极材料拥有最高的首次放电容量（348.9mAhg-1）和最好的容量循环性能。     

Phase composition,formation parameters,and morphology of precipitates in the LiVO<Subscript>4</Subscript>-VOSO<Subscript>4</Subscript>-H<Subscript>2</Subscript>O system

The phase and chemical compositions of the precipitates formed in the LiVO₃-VOSO₄-H₂O system at initial pH within 1 ≤ pH ≤ 4 and 90°C were studied. The following phases were prepared: an α phase Li_1.4(VO)_1.3[H₂V₁₀O₂₈] · nH₂O and a β phase Li_{0.6 ? x} H_{1.4 + x} [V₁₂O_{31 ? y/2}] · nH₂O (0 ≤ x ≤ 0.5, 1.3 ≤ y ≤ 2.0) with a layered structure. Li_0.4V₂O₅ · H₂O nanorods with the interlayer distance 10.30 ± 0.08 Å were synthesized at 180°C in an autoclave. The morphology, IR spectra, and main formation processes for these polyvanadates were studied.     

XPS study of the Li intercalation process in sol–gel‐produced V2O5 thin film: influence of substrate and film synthesis modification

We report on the process of lithium intercalation in V₂O₅ thin films deposited onto standard ITO‐coated glass substrates. The films were deposited via a well‐established sol–gel route, and the samples were examined as working electrodes in a range of potentials versus lithium reference electrode. This paper follows up issues arising from parallel spectroscopic characterizations of the films by X‐ray photoelectron spectroscopy (XPS). Specifically, the XPS examination showed that not all of the Li‐ion charge inserted was accounted for by the V(5) to V(4) reduction, but the stoichiometric balance could be maintained only by considering additional oxygens arising from the intercalation procedure, leading to Li₂O formation. In this work, we have examined the possibility that the source of oxygen is the ITO substrate. To this purpose, films of V₂O₅ deposited on silicon substrates have been prepared using the sol–gel process and examined by XPS after electrochemical intercalation/de‐intercalation cycles. We show that in this case a perfect balance between electrochemical charge, inserted Li and reduced vanadium is obtained. A further indication of ITO‐substrate effects was obtained from examination, by the same methods, of some unconventional V₂O₅ films that had been co‐precipitated with a siloxane, designed to provide a template structure. The results obtained from this material imply that a barrier layer is formed at the ITO interface and, therefore, the formation of Li₂O is avoided. The results are discussed in terms of the possible degradation of conventional V₂O₅ on ITO as a result of electrochemically induced interface reactions. Copyright © 2005 John Wiley & Sons, Ltd.     

In Situ Construction of an Ultra‐Stable Conductive Composite Interface for High‐Voltage All‐Solid‐State Lithium Metal Batteries

The garnet electrolyte presents poor wettability with Li metal, resulting in an extremely large interfacial impedance and drastic growth of Li dendrites. Herein, a novel ultra‐stable conductive composite interface (CCI) consisting of Li_ySn alloy and Li₃N is constructed in situ between Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) pellet and Li metal by a conversion reaction of SnN_x with Li metal at 300 °C. The Li_ySn alloy as a continuous and robust bridge between LLZTO and Li metal can effectively reduce the LLZTO/Li interfacial resistance from 4468.0 Ω to 164.8 Ω. Meanwhile, the Li₃N as a fast Li‐ion channel can efficiently transfer Li ions and give their uniform distribution at the LLZTO/Li interface. Therefore, the Li/LLZTO@CCI/Li symmetric battery stably cycles for 1200 h without short circuit, and the all‐solid‐state high‐voltage Li/LLZTO@CCI/LiNi_0.5Co_0.2Mn_0.3O₂ battery achieves a specific capacity of 161.4 mAh g^?1 at 0.25 C with a capacity retention rate of 92.6 % and coulombic efficiency of 100.0 % after 200 cycles at 25 °C.     

Electrochemically Generated γ‐LixV2O5 as Insertion Host for High‐Energy Li‐Ion Capacitors

In this study, we explored the feasibility of using electrochemically generated γ‐Li_xV₂O₅ as an insertion‐type anode in the lithium‐ion capacitor (LIC) with activated carbon (AC) as a cathode. Along with the native form of V₂O₅, their carbon composites are also used as the electrode material which is prepared by high‐energy ball milling. The electrochemical pre‐lithiation strategy is used to generate the desired γ‐phase of V₂O₅ (γ‐Li_xV₂O₅). Under the optimized mass loading conditions, the LICs are assembled with γ‐Li_xV₂O₅ as anode and AC as a cathode in the organic medium. Among the different LICs fabricated, AC/γ‐Li_xV₂O₅‐BM50 configuration delivered an energy density of 33.91 Wh kg^?1 @ 0.22 kW kg^?1 with excellent capacity retention characteristics. However, a dramatic increase in energy density (43.98 Wh kg^?1@0.28 kW kg^?1) is noted after the electrolyte modification with fluoroethylene carbonate. The high temperature performance of the assembled LIC is also studied and found that γ‐Li_xV₂O₅ phase can be used as a potential battery‐type component to construct high‐performance hybrid charge storage devices.     

Zur Bedeutung von V2O3(OH)4(g) für den chemischen Transport von V2O5(s) in Anwesenheit von Wasser. Nachweis des Gasteilchens,thermodynamische Daten und Modellrechnungen

V₂O₃(OH)₄(g), Proof of Existence, Thermochemical Characterization, and Chemical Vapor Transport Calculations for V₂O₅(s) in the Presence of Water By use of the Knudsen-cell mass spectrometry the existence of V₂O₃(OH)₄(g) is shown. For the molecules V₂O₃(OH)₄(g), V₄O₁₀(g), and V₄O₈(g) thermodynamic properties were calculated by known Literatur data. The influence of V₂O₃(OH)₄(g) for chemical vapor transport reactions of V₂O₅(s) with water ist discussed. Δ_BH°(V₂O₃(OH)₄(g), 298) = –1920 kJ · mol^–1 and S°(V₂O₃(OH)₄(g), 298) = 557 J · K^–1 · mol^–1, Δ_BH°(V₄O₁₀(g), 298) = –2865,6 kJ · mol^–1 and S°(V₄O₁₀(g), 298) = 323.7 J · K^–1 · mol^–1, Δ_BH°(V₄O₈(g), 298) = –2465 kJ · mol^–1 and S°(V₄O₈(g), 298) = 360 J · K^–1 · mol^–1.     

Amorphous Li2O2: Chemical Synthesis and Electrochemical Properties

When aprotic Li–O₂ batteries discharge, the product phase formed in the cathode often contains two different morphologies, that is, crystalline and amorphous Li₂O₂. The morphology of Li₂O₂ impacts strongly on the electrochemical performance of Li–O₂ cells in terms of energy efficiency and rate capability. Crystalline Li₂O₂ is readily available and its properties have been studied in depth for Li–O₂ batteries. However, little is known about the amorphous Li₂O₂ because of its rarity in high purity. Herein, amorphous Li₂O₂ has been synthesized by a rapid reaction of tetramethylammonium superoxide and LiClO₄ in solution, and its amorphous nature has been confirmed by a range of techniques. Compared with its crystalline siblings, amorphous Li₂O₂ demonstrates enhanced charge‐transport properties and increased electro‐oxidation kinetics, manifesting itself a desirable discharge phase for high‐performance Li–O₂ batteries.