Cloud point formation based on mixed micelles in the presence of electrolytes for cobalt extraction and preconcentration

A new micelle-mediated phase separation of metal ions, applied for preconcentrating trace levels of cobalt as a prior step to its determination by flame atomic spectroscopy, has been developed. Two methods were proposed employing both Triton X-100 and sodium dodecyl sulfate (SDS) as a mixed micellar system while the phase separation was induced by HCl or NaCl addition. Cobalt was complexed with pyridylazo compounds (PAN, PAR, 5-Br-PADAP) in an aqueous surfactant medium and it was concentrated in the surfactant rich phase after phase separation. The chemical variables affecting the cloud point extraction were evaluated, optimized and successfully applied to cobalt determination in pharmaceutical samples. Under the optimized conditions, the preconcentration system permitted limits of detection as 1.1 and 1.6 μg l⁻¹ cobalt, respectively, when HCl and NaCl were used. Both proposed methods showed linear calibration within a 25-200 μg l⁻¹ cobalt range. The extraction efficiency was investigated at different cobalt concentrations (40-185 μg l⁻¹) and good recoveries (98-102%) were obtained by using NaCl as electrolyte. The results obtained were compared with those observed with ET AAS.     

Depression in the cloud point of Tween in the presence of glycol additives and triblock polymers

Cloud point (C_P) measurements of Tween 20 and Tween 80 were carried out in the presence of various glycol oligomers and triblock polymers (TBP). The cloud points of both Tween 20 and 80 decrease in the presence of both types of additives. Among the glycol oligomeric additives, ethylene glycol monobutyl ether was found to reduce the C_P maximum. An increase in the repeating units of polymeric glycol additives leads to a decrease in C_P. Reduction in the C_P in the presence of TBP depends upon the increase in hydrophobic/hydrophilic ratio among the polypropylene to polyethylene units.     

可见光照射下温敏锌酞菁共聚物光催化氧化对氯苯酚

将含有不饱和双键的四马来酰胺基锌酞菁（ZnMPc）与N-异丙基丙烯酰胺（NIPA）共聚,制备得到一种新型温敏锌酞菁共聚物光催化剂：P（NIPA—co—ZnMPc）,采用差示扫描量热法测得其低临界溶解温度（LCST）为33．5℃．在可见光照射下利用氧气作为氧化剂,P（NIPA—co-ZnMPc）~g有效地催化氧化对氯苯酚（4-CP）,与小分子ZnMPc相比,P（NIPA-co-ZnMPc）具有更高的光催化活性．两者在水溶液中的紫外．可见光谱图显示,共聚后大分子链的阻隔作用能有效地抑制酞菁分子的二聚,从而大大提高了其催化活性．温度对其光催化活性的实验结果显示,P（NIPA-co-ZnMPc）在其LCST附近具有最高的催化效率,说明催化剂的聚集态结构对其光催化活性产生直接影响,通过测定其在不同温度下的流体力学半径,可推测在其LCST附近发生了分子间的疏水聚集,会对4-CP起富集作用,从而加快了光催化反应速率．该光催化剂可通过均相催化异相分离实现循环利用,实验表明该催化剂具有较高的稳定性．     

Fabrication of thermosensitive PCL‐PNIPAAm‐PCL triblock copolymeric micelles for drug delivery

A series of thermosensitive ABA type triblock poly(ε‐caprolactone)‐b‐poly(N‐isopropylacrylamide)‐b‐poly(ε‐caprolactone) (PCL‐PNIPAAm‐PCL) copolymers with different molecular weights were synthesized by the combination of ring opening polymerization and reversible addition‐fragmentation chain transfer (RAFT) polymerization. The critical micelle concentrations (CMCs) of the resulted four triblock copolymers in aqueous solution were determined to be 33.8, 39.8, 35.5, and 41.7 mg/L, respectively, by fluorescence spectroscopy using pyrene as a fluorescence probe. Optical absorption measurements showed that the lower critical solution temperatures (LCSTs) of the copolymers were 35.8, 36.2, 35.2, and 36.2 °C, respectively, in distilled water, and 33.9, 34.2, 33.3, 34.6 °C, respectively, in PBS (pH = 6.8, I = 0.1). Transmission electron microscopy (TEM) showed that the self‐assembled micelles exhibited a well‐defined spherical shape with diameter of around 100 nm. The drug‐loaded PCL‐PNIPAAm‐PCL micelles displayed thermosensitive controlled release behaviors. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3048–3057, 2008     

Photocatalytic oxidation of 4-chlorophenol using thermosensitive zinc phthalocyanine copolymer under visible light irradiation

A novel thermosensitive photocatalyst,P(NIPA-co-ZnMPc),has been prepared using zinc tetra(N-carbonylacrylic)aminophthalocya-nine(ZnMPc) to copolymerize with N-isopropylacrylamide(NIPA).The lower critical solution temperature(LCST) of P(NIPA-co-ZnMPc) measured by differential scanning calorimetry(DSC) was 33.5 °C.P(NIPA-co-ZnMPc) effectively catalyzes the oxidation of 4-chlorophenols(4-CP) using oxygen as oxidant under the visible light irradiation,and it has higher photocatalytic activity than ZnMPc under t...     

Cloud point prediction of fuels and fuel blends

The cloud point temperature, the temperature at which the first wax crystals appear in solution, is one of the most important specifications associated with the low temperature behaviour of a fuel. A database of about 80 fuels and fuel blends was collected and used to assess the performance of the three predictive local composition models (Wilson, NRTL and UNIQUAC) for cloud point prediction. The results indicates that Predictive UNIQUAC can predict the cloud points of the fuels within the experimental uncertainty of the measurements. It could thus be a useful tool in the production of fuels both in the design of refining process and the blend of fuels to meet the low temperature specifications.     

Effect of hydrotropes on the solution behavior of PEO/PPO/PEO block copolymer L62 in aqueous solutions

Effect of hydrotropes viz. sodium benzene sulfonate (NaBS), sodium toluene sulfonate (NaTS) and sodium xylene sulfonate (NaXS) on the micellization, phase behavior and structure of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymer L62 in aqueous solution was studied by surface tension, dye spectral, cloud point and small angle neutron scattering measurements. The addition of hydrotropes increased the critical micelle concentration (CMC) of L62 which appears to be logistic as the added hydrotrope enhances the solubility of PPO moiety (and PEO) making it behave like a more hydrophilic block copolymer that would micellize at high copolymer concentration. Partial phase diagram of L62 in water shows two cloud point (CP) in the concentration range (0-10 wt.%). Addition of hydrotropes shifts the L62 concentration range showing double cloud points at lower side of concentration; sodium xylene sulfonate (NaXS) being more effective. SANS data for L62 in the presence of 0.4 and 0.8 M NaXS at temperatures <30 °C showed unimers which are fully dissolved Gaussian chains. The unimer-to-micelle transition takes place when temperature is increased. It is found that SANS data for L62 in the presence of 0.4 M NaXS (40 and 50 °C) and 0.8 M NaXS (45 and 50 °C) correspond to ellipsoidal structure of micelles.     

Phase behavior and surface tensions of amphiphilic fluorinated random copolymer aqueous solutions

Phase behavior and surface tension of aqueous solutions of fluorinated random copolymers [perfluoroalkylacrylate]–[poly(ethyleneoxide)methacrylate], [C_mRf-acrylate]-[EO_n-methacrylate] with fluroalkyl carbon number m = 8, 6, 4, 2 and number of ethyleneoxide unit, n = 9 and 4.5 were investigated as a function of composition and different combinations of m and n. Isotropic solutions are formed at lower temperatures over wide concentration range of copolymer but at higher temperature phase separation occurs. The cloud point of copolymer decreases with decreasing n as well as m, and also with decreasing the number of poly(ethyleneoxide)methacrylate chain per perfluorinatedalkylacrylate chain, suggesting that the copolymers become more hydrophobic on decreasing m and n. Equilibrium and dynamic surface tension measurements show that copolymers become increasingly surface active as m as well as n decrease but the adsorption at the air–water interface is very slow due to bulkiness of the molecules. No clear evidence of the formation of micellar aggregates could be obtained from surface tension–composition curves.     

Influence of various series of additives on the clouding behavior of aqueous solutions of triblock copolymers

The cloud point (CP) studies on aqueous solutions of two ethylene oxide-propylene oxide triblock copolymers (EO)_2.5(PO)₃₁(EO)_2.5 and (EO)₁₃(PO)₃₀(EO)₁₃ with varying number of ethylene oxide (EO) units were carried out in the presence of series of additives, such as alkali, acids, ionic surfactants, alcohols, salts, and hydrotropes. The results of this study show that sodium hydroxide decreases the CP of the two copolymers. Acids increase the CP in the order hydrochloric acid > acetic acid > formic acid for both the triblock copolymers. Hydrotropes increase the CP, whereas salts decrease or increase the CP based on their salting-out/salting-in nature. Alcohols, which are polar organic additives, affect the CP of the two copolymers differently. The change in the CP of the triblock copolymers depends upon the structure and concentration of the additives and on the number of EO units of the two triblock copolymers.     

Swelling behavior of thermosensitive polyvinyl alcohol-graft-N-isopropylacrylamide copolymer membranes containing carboxyl groups and properties of their polymer solutions

The thermosensitive polyvinyl alcohol-graft-N-isopropylacrylamide–methacrylic acid (PVA-g-NIPAAm–MAc) terpolymer membranes containing carboxyl groups were prepared. The swelling ratios of the membranes were measured at various temperatures. The temperature dependence of the swelling ratios of the terpolymer membranes was different from that of PVA-g-NIPAAm copolymer membranes. The swelling ratios of PVA-g-NIPAAm–MAc (5–15) (wt % in feed) increased with increasing temperature up to 35–38°C, then decreased. However, the swelling ratio of PVA-g-NIPAAm–MAc (30–50) terpolymer membranes did not depend on temperature in the temperature range of 10–48°C. To clarify the swelling behavior of the PVA-g-NIPAAm–MAc terpolymer membranes, the swelling ratios of the PVA-g-NIPAAm–Acrylic acid (AAc) terpolymer membranes, the viscosity, and optical density of various polymer solutions were measured. The different swelling behavior of PVA-g-NIPAAm–MAc (or AAc) terpolymer membranes from that of PVA–NIPAAm copolymer membranes was thought to be due to hydrogen bonding between amide groups in NIPAAm moieties and carboxyl groups in MAc (or AAc) moieties in the terpolymer membranes and the difference of swelling behavior between PVA-g-NIPAAm–MAc and PVA-g-NIPAAm–AAc terpolymer membranes was thought to be brought about by hydrophobic interaction due to methyl groups in PVA-g-NIPAAm–MAc terpolymer membranes. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3097–3106, 1998     

Cloud point extraction preconcentration for capillary electrophoresis of metal ions

The application of the cloud point extraction (CPE) technique for capillary electrophoresis (CE) determination of metal ions was demonstrated using Cu(II) and Co(II) as model metal ions. The preconcentration of Cu(II) and Co(II) in aqueous solution was achieved by CPE with 1-(2-pyridylazo)-2-naphthol (PAN) as the chelating agent and Triton X-114 as the extractant. Baseline separation of the PAN chelates of Cu(II) and Co(II) was realized by CE with a photodiaode array detector in a  μm i.d. fused-silica capillary at 17 kV. A 50 mM NH₄Ac buffer solution (pH 8.0) containing 0.2 mM of PAN in 80% (v/v) of acetonitrile and 20% (v/v) doubly deionized water (DDW) was used as the separation medium to avoid the adsorption of hydrophobic substances and nonionic surfactant Triton X-114 onto the inner surface of the separation capillary, ensuring the separation efficiency and reproducibility. The precision (relative standard deviation (R.S.D.), n=5) for five replicate injections of a mixture of 20 μg/l of Co(II) and Cu(II) were 0.74 and 1.8% for the migration time, 3.1 and 0.64% for the peak area measurement, respectively. The apparent concentration factor, which is defined as the concentration ratio of the analyte in the final diluted surfactant-rich extract ready for CE separation and in the initial solution, was 15.9 for Co(II) and 16.3 for Cu(II). The linear concentration range was from 3 to 100 μg/l for both Co(II) and Cu(II). The detection limits of Co(II) and Cu(II) were 0.12 and 0.26 μg/l, respectively. The developed method was successfully applied to the determination of Co(II) and Cu(II) in tap water, snow water, and flavor wines.     

浊点萃取-紫外可见分光光度法测定痕量金

建立了以四甲基联苯胺(TMB)为络合剂,非离子表面活性剂Triton-114为萃取剂的浊点萃取-紫外可见分光光度法测定痕量金的方法。考察了溶液的pH、络合剂和表面活性剂浓度、平衡温度和时间等条件对浊点萃取的影响。在最优条件下,该方法对金的富集倍数为12倍,线性范围为0～0.5μg/mL,检出限(3σ)为8.6ng/mL,相对标准偏差RSD为2.3%～3.6%(n=6),回收率在97%～102%之间。方法已用于工业废水中痕量金的测定。     

Study of micellar and phase separation behavior of mixed systems of triblock polymers

Cyclic voltammetric (CV) techniques have been employed to study the mixed micellar behavior of binary mixtures of triblock polymers (TBP) such as F127+P85, F127+P85, F88+P85, and F88+P123 using 2,2,6,6-tetramethyl-1-piperidinyloxy (Tempo) as an electroactive probe. Critical micellar concentration (cmc) has been obtained for pure triblock polymers and their mixed systems from the plots of peak current (i_p) variation versus the total concentration. Diffusion coefficients of the electroactive species have been determined from the Randles–Sevcik equation. The interaction parameter (β) for the mixed micelles was obtained from the regular solution theory. The values of β suggest that the synergism does exist especially with the F88+P123 system. Cloud point measurements have also been made on the binary mixtures of triblock polymers following similar mixing criteria. An effort has been made to correlate the micellar behavior and phase separation (cloud point) phenomenon. From the correlation, it can be concluded that in the systems studied, an increase in cmc increases the cloud point of mixed systems of triblock polymers.     

Surface-induced morphologies of ABC star triblock copolymer in spherical cavities

The morphologies and phase diagrams exhibited by symmetric ABC star triblock copolymer nanoparticles are investigated on the basis of real-space self-consistent field theory. The ABC star triblock copolymers were chosen to be tiling-forming with fixed polymer parameter and the spherical boundaries were modeled using the masking technique. We first study a number of examples where the ABC triblock copolymers confined in spherical cavities with neutral surface. Then, two types of spherical cavity distinct preferential surfaces are considered, including both A-block attractive and repulsive preferential surfaces. We aim at the effects due to various spherical cavity diameters and the degree of interactions between the polymer and the spherical surface. A variety of morphologies, such as ring-like structures, concentric sphere, and irregular cylinder, were identified in phase diagrams. The results show that both the degree of interactions and spherical diameters can influence the formation of morphologies so that ring-like structures and other novel structures could be obtained.     

Aqueous solution behavior of thermosensitive (N-isopropylacrylamide-acrylic acid-ethyl methacrylate) terpolymers

A series of N-isopropylacrylamide (NIPAM)-acrylic acid–ethyl methacrylate terpolymers with varied monomer compositions was prepared by radical polymerization. The solution behavior of these polymers was studied in dilute aqueous solution using spectrophotometry, fluorescence spectroscopy and high-sensitivity differential scanning calorimetry. The results obtained revealed that the lower critical solution temperatures depend strongly on the copolymer composition, solution pH and ionic strength. At a high pH, the ionization of acrylic acid (AA) units leads to an increase in solution cloud points (T_c). Solutions of polymers containing 10% or less of AA display a constant T_c for pH above 5.5, with 15% there is a continuous increase in T_c with pH and, for higher AA contents, no clouding was observed within the studied temperature range. Fluorescence probe studies were conducted by following the I ₁/I ₃ ratio of pyrene vibronic bands and the emission of anilinonaphtalene sulfonic acid, sodium salt (ANS), both approaches revealing the existence of hydrophobic domains for polymers with higher ethyl methacrylate content at temperatures lower than T_c, suggesting some extent of aggregation and/or a coil-to-globule transition. Scanning calorimetry measurements showed an endothermic transition at temperatures agreeing with the previously detected cloud points. Moreover, the transition curves became broader and with a smaller transition enthalpy, as both the AA content and the solution pH were increased. These broader transitions were interpreted to be the result of a wider molecular distribution upon polymer ionization, hence, displaying varied solution properties. The decrease in transition enthalpy was rationalized as a consequence of reminiscent hydration of NIPAM units, even after phase separation, owing to the presence of electric charges along the polymer chain.     

Aggregation behavior of star-like PEO-PPO-PEO block copolymer in aqueous solution

The aggregation behavior of a star-like amphiphilic block copolymer (denoted as AP432, which was synthesized via anionic polymerization), in aqueous solutions was investigated by surface tension, steady-state fluorescence, dynamic light scattering (DLS) and transmission electron microscopy (TEM). For comparison, a commercially available linear amphiphilic PEO-PPO-PEO block copolymer, Pluronics L64, which has a similar PEO fraction to AP432, was also studied. It is found that the different molecular structure of AP432 and L64 leads to a significant difference on their behavior both at the air/water interface and in bulk aqueous solutions. The results of surface tension measurements indicate that the surface activity of AP432 is much more pronounced than that of L64. The formation of AP432 and L64 aggregates are identified by DLS, fluorescence and TEM measurement.     

Cloud point extraction for ultra-trace Cd determination in microwave-digested biological samples by ETAAS

Cloud point extraction (CPE) has been used for the preconcentration of cadmium, after the formation of a complex with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (5-Br-PADAP), and further determination by graphite furnace atomic absorption spectrometry (ETAAS) using polyethyleneglicolmono-p-nonyphenylether (PONPE 7.5) as surfactant. The chemical variables that affect the cloud point extraction were optimized. The separation of the two phases was easily accomplished by cooling the mixture in order to make more viscous the surfactant-rich phase. In order to establish the optimum conditions for the determination of Cd by ETAAS, Pd + Mg, Pt, Ir, Rh and Ru were studied as chemical modifiers. The best thermal stabilization was obtained with Pd + Mg, with a maximum pyrolysis temperature of 1100 °C. Under the optimum conditions i.e., pH 9.0, [5-Br-PADAP] = 2.0 × 10⁻⁵ mol L⁻¹, [PONPE 7.5] = 0.02% (w/v), an enhancement factor of 22-fold was reached. The lower limit of detection (LOD) obtained under the optimal conditions was 0.008 μg L⁻¹. The precision for 10 replicate determinations at 0.2 μg L⁻¹ Cd was 3.5% relative standard deviation (R.S.D.). The calibration graph using the preconcentration method was linear with a correlation coefficient of 0.9984 at levels close to the detection limit up to at least 1.0 μg L⁻¹. The method was successfully applied to the determination of cadmium in urine samples and in a water standard reference material.     

浊点萃取-火焰原子吸收光谱法测定淡水鱼中痕量铅

采用以双硫腙为络合剂、Triton X-100为表面活性剂的新型浊点萃取体系富集淡水鱼中的痕量铅,并用火焰原子吸收光谱法对其进行测定。探讨了溶液pH、表面活性剂浓度、络合剂用量、平衡温度、平衡时间等对浊点萃取及测定灵敏度的影响,优化了实验条件。在最佳条件下测得铅的检出限为0.090μg/L,校准曲线相关系数为0.9999。该方法已用于淡水鱼中痕量铅的测定。     

Cloud point extraction for determination of cadmium in soft drinks by thermospray flame furnace atomic absorption spectrometry

Cloud point extraction (CPE) is proposed as a preconcentration procedure for the determination of Cd in soft drinks by thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS). The cadmium reacted with pyridyl-azo-naphthol (PAN) to form hydrophobic chelates, which were extracted into the micelles of Triton X-114 in a solution buffered at pH 9. NaCl was used for the phase separation. The variables which affect the preconcentration were optimized using a 2³ factorial design and central composite design (CCD). A response surface maximum point was obtained, and the critical values were a concentration of 0.13 mmol L^? 1 PAN, 0.03% m/v Triton X-114 and 2.3% m/v NaCl. Under the optimized conditions, after the extraction and preconcentration steps, a sample volume of 100 μL was introduced into the hot Ni tube using water as the carrier at a flow rate of 0.4 mL min^? 1. The values obtained for the detection limit, relative standard deviation and preconcentration factor were 0.0178 μg L^? 1, 4.1% (n = 8) and 55.5, respectively. The accuracy of the proposed method was demonstrated by performing addition-recovery experiments. Recoveries varied from 88 to 104%.