Enolic schiff base aluminum complexes and their catalytic stereoselective polymerization of racemic lactide

A series of enolic Schiff base aluminum(III) complexes LAlR (where L=NNOO-tetradentate enolic Schiff base ligand) containing ligands that differ in their steric and electronic properties were synthesized. Their single crystals showed that these complexes are five-coordinated around the aluminum center. Their coordination geometries are between square pyramidal and trigonal bipyramidal. Their catalytic properties in the solution polymerization of racemic lactide (rac-LA) were examined. The modifications in the auxiliary ligand exhibited a dramatic influence on the catalytic performance. Lengthening the backbone from C(2) alkylene to C(3) alkylene resulted in remarkable enhancement of both the stereoselectivity and the polymerization rate because of the increasing flexibility of the diimine backbone. Electron-withdrawing substituents in the diketone also highly improved the activity and the stereoselectivity. Among these complexes, 4 b had the highest activity and the stereoselectivity owing to the C(3) alkylene backbone and the two gem-methyl groups on the middle carbon atom. The value of the polymerization rate constant (k(p)) catalyzed by 4 b in 70 degrees C was 1.90 L mol(-1) min(-1), the activation energy of the polymerization (35.4 kJ mol(-1)) was calculated according to the Arrhenius equation. Other factors that influenced the polymerization, such as the polymerization time, the temperature, and the monomer concentration, are also discussed in detail.     

Thermal degradation of iron chelate complexes adsorbed on mesoporous silica and alumina

Nanometric Fe₂O₃ particles could be inserted inside the internal pore volume of SBA-15 mesoporous silica and mesoporous alumina supports, when Fe(III) chelates (EDTA, gluconate or citrate) were used as impregnating precursors. The oxidative degradation of the chelating anions was followed by combined TG-DTA. Strong chelate-SiOH interactions (case of bulky EDTA), favored by the mesopore curvature, yield sub-nanometric extremely well dispersed Fe₂O₃ particles preferentially located at the micropore mouths (confinement effect). Fe₂O₃ even more strongly interacts with alumina walls, generating either (Fe,Al)₂O₃ mixed phases or Fe-aluminate micro domains. These iron-based mesoporous alumina composites proved very active catalysts in total oxidation of phenol at ambient conditions, with extremely low iron leaching (0.2%).     

Schiff base complexes and their versatile applications as catalysts in oxidation of organic compounds: part I

Schiff bases and their complexes are good candidates as versatile compounds which are synthesized by the condensation of a primary amino compound with either aldehydes or ketones for a variety of industrial applications. They can act as catalysts in the catalytic oxidation of organic compounds. Recent researches in oxidation catalysis have focused on how to employ the metal‐catalyzed oxidation of organic substrates. This review summarizes the current developments of the last few decades for the oxidations of organic compounds that proceed through Schiff base complexes. The chemical syntheses of Schiff bases and their complexes are outlined.     

New carboxy-functionalized terpyridines as precursors for zwitterionic ruthenium complexes for polymer-based solar cells

New carboxy-terpyridines selectively functionalized at the 4-, 4′- and 4″-positions were prepared in a three-step procedure with good yields using the Kröhnke reaction followed by saponification. Their complexation with ruthenium led to symmetric and unsymmetric terpyridinyl zwitterionic complexes.     

A fluorescent and colorimetric chemosensor for selective detection of aluminum in aqueous solution

We have synthesized a new Schiff base 1, which detects Al³⁺ through fluorescence and naked eye in aqueous solution. The sensor 1 exhibited selective and sensitive recognition toward Al³⁺ via significant fluorescence enhancement (31-fold). Moreover, it showed a significant color change from colorless to yellow. The complex formation was proposed to be 1:1 ratio, based on the Job plot, ESI-mass spectrometry analysis, ¹H NMR titration, and IR analysis. The detection limit was 1.00 μM, which is below the WHO acceptable limit (1.85 μM) in drinking water. In addition, the sensor 1 could be recyclable simply through treatment with a proper reagent such as EDTA.     

Aluminum complexes of sterically hindered tetradentate Schiff bases: Synthesis, structure, and reactivity toward -caprolactone

The sterically hindered Schiff bases tbmSalenH₂ [tbmSalen = N,N′-1,2-ethylenebis(3-tert-butyl-5-methylsalicylideneimine)] and tbmSalcenH₂ [tbmSalcen = N,N′-trans-1,2-cyclohexanediyl-bis(3-tert-butyl-5-methylsalicylideneimine)] afforded a series of aluminum complexes of the general formulae [Al(tbmSalen)X] and [Al(tbmSalcen)X] (X = Cl, Me, Et). The molecular structure of [Al(tbmSalcen)Cl] was determined by single-crystal X-ray structural analysis which revealed a five-coordinate aluminum center with a distorted square pyramidal geometry. The alkyl complexes were found to oligomerize -caprolactone.     

Fluorescent chemosensor based-on naphthol-quinoline for selective detection of aluminum ions

In this study, an assay to quantify the presence of aluminum ions with a receptor containing naphthol and quinoline moieties was developed using a turn-on fluorescence enhancement approach. Upon treatment with aluminum ions, the fluorescence of the receptor was enhanced at 510 nm due to the formation of a complex between the ligand and aluminum ions at room temperature. As the concentration of Al³⁺ was increased, the fluorescence gradually increased. Other metal ions, such as K⁺, Ag⁺, Ca²⁺, Mg²⁺, Zn²⁺, Mn²⁺, Co²⁺, Ni²⁺, Cu²⁺, Cd²⁺, Cr³⁺, Fe³⁺, In³⁺, had no significant effect on the fluorescence.     

Titanium complexes bearing carbamato ligands as catalytic precursors for propylene polymerization reactions

This report describes propylene polymerization reactions with titanium complexes bearing carbamato ligands, Ti(O₂CNMe₂)Cl₂ ( I ) and Ti(O₂CR₂)₄ [R₂ = NMe₂ ( II ), NEt₂ ( III ) and ( IV )]. Combinations of these complexes and MAO form catalysts for the synthesis of atactic polypropylene, as confirmed by FT‐IR, DSC and ¹³C NMR analysis. Effects of main reaction parameters on the catalyst activity were studied including the type of complex, solvent, temperature, and the [Al]/[Ti] molar ratio. The highest activity was observed when chlorobenzene was used as a solvent and AlMe₃‐depleted MAO was employed as a cocatalyst. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4095–4102     

Transition metal complexes of tetradentate and bidentate Schiff bases as catalysts for ethylene polymerization: Effect of transition metal and cocatalyst

This article compares catalytic performance of ethylene polymerization in similar polymerization conditions of transition metal complexes having two ligands [O,N] (phenoxy‐imine) and having one tetradentate ligand [O,N,N,O] (salphen or salen). It is shown that the activity of both complex types as well as the product properties depend in the same way on the type of central metal in the complex and on the cocatalyst used. Although the type of ligand has some effect on the catalyst activity, yet it does not control the properties of the obtained products. The vanadium and zirconium complexes, irrespective of the cocatalyst used, yield linear polyethylene with high molecular weight (a few hundred thousand g/mol). Similar products are formed when titanium complexes activated with MAO are employed. On the other hand, the same titanium complexes in conjunction with Et₂AlCl, yield low molecular weight polyethylene (of a few thousand) and additionally a mixture of oligomers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 565–575, 2009     

Syntheses,EPR spectral studies and crystal structures of manganese(II) complexes of neutral N,N donor bidentate Schiff bases and azide/thiocyanate as coligand

Four manganese(II) complexes Mn₂(paa)₂(N₃)₄ (1), [Mn(paa)₂(NCS)₂]·³/₂H₂O (2), Mn(papea)₂(NCS)₂ (3), [Mn(dpka)₂(NCS)₂]·¹/₂H₂O (4) of three neutral N,N donor bidentate Schiff bases were synthesized and physico-chemically characterized by means of partial elemental analyses, electronic, infrared and EPR spectral studies. Compounds 3 and 4 were obtained as single crystals suitable for X-ray diffraction. Compound 4 recrystallized as Mn(dpka)₂(NCS)₂. Both the compounds crystallized in the monoclinic space groups P2₁ for 3 and C2/c for 4. Manganese(II) is found to be in a distorted octahedral geometry in both the monomeric complexes with thiocyanate anion as a terminal ligand coordinating through the nitrogen atom. EPR spectra in DMF solutions at 77 K show hyperfine sextets with low intensity forbidden lines lying between each of the two main hyperfine lines and the zero field splitting parameters (D and E) were calculated.     

Antihypertensive drugs as an inhibitors for corrosion of aluminum and aluminum silicon alloys in aqueous solutions

The corrosion behavior of aluminum and three aluminum–silicon alloys in different concentrations of HCl solutions and its inhibition by antihypertensive drugs was studied using potentiostatic polarization measurements. As the acid concentration increases, the rate of corrosion increases. Aluminum is less susceptible to corrosion than any of Al–Si alloys. The inhibition efficiency of the drug compounds increases with their concentration up to a critical value. At higher additive concentrations the inhibition efficiency starts to decrease. The inhibitive action of these compounds is due to their formation of insoluble complex adsorbed on the metal surface. The adsorption follows Langmuir adsorption isotherms. It was found that the drugs compounds provide protection to Al and Al–Si alloys against pitting corrosion by shifting the pitting potential to more positive direction until critical drug concentrations (250 ppm). After this critical concentration the inhibition against to pitting corrosion starts to decrease.     

Functional zinc(II) phthalocyanines bearing Schiff base complexes as oxidation catalysts for bleaching systems

Oxidation catalysis is used to increase the performance of hydrogen peroxide in laundry bleach applications. Bleach catalysts provide cost‐effective, energy‐saving and environmentally friendly bleach systems yielding perfect stain removal at lower temperatures. This comparative study is based on the synthesis of bis[bis(salicylhydrazonephenoxy)manganese(III)] phthalocyaninatozinc(II) ( 2 ), bis[bis(salicylhydrazonephenoxy)cobalt(III)] phthalocyaninatozinc(II) ( 3 ) and bis[bis(salicylhydrazonephenoxy)iron(III)] phthalocyaninatozinc(II) ( 4 ) as tri‐nuclear complexes consisting of two Schiff base complexes substituting a zinc phthalocyanine. Complexion on the periphery to obtain complexes 2 , 3 , 4 was performed through the reaction of a Schiff base‐substituted phthalocyanine using MnCl₂?4H₂O, CoCl₂?6H₂O or FeCl₃?6H₂O salts in basic condition in dimethylformamide. Fourier transform infrared, ¹H NMR, ¹³C NMR, UV–visible, inductively coupled plasma optical emission and mass spectra were applied to characterize the prepared compounds. The bleach performances of the three phthalocyanine compounds 2 , 3 , 4 were examined by the degradation of morin as hydrophilic dye. The degradation progress in the presence of catalysts 2 , 3 , 4 /H₂O₂ combination in aqueous solution was investigated using an online spectrophotometric method. It was found that the catalysts 2 , 3 , 4 exhibited better bleaching performance at 25 °C than tetraactylethylethylenediamine as bleach activator used in powder detergent formulations for stain removal. Copyright © 2015 John Wiley & Sons, Ltd.     

Silica gel modified with lumogallion for aluminum determination by spectroscopic methods

Simple, easy to use and selective method of Al(III) sorption-spectroscopic (SS) determination was proposed. For this purpose, silica modified with tridecyloctadecylammonium chloride(SGII) using adsorption technique and glass slide modified with thin silica-poly(dimethyldiallyl-ammonium chloride) (SGI) composite film obtained by sol-gel technique were worked out. It was shown that lumogallion (LG) easily absorbs on SGI and SGII. Obtained sorbents SGIII and SGIV, respectively, were used for aluminum(III) determination by diffuse reflectance and spectrophotometric methods. The ranges of determination were (mg L⁻¹): (0.08-0.54), s_r ≤ 0.13, n = 4 for SGIII and (0.05-2.0), s_r ≤ 0.11, n = 4 for SGIV. The detection limits (blank + 3σ) for aluminum were 70 and 30 μg L⁻¹ using SGIII and SGIV, respectively, where σ is the standard deviation of blank estimation. The accuracy of the developed spectrophotometric method was examined by the determination of standard addition of aluminum in alcohol-free beverages. The relative error did not exceed 9%. SGIII can be regenerated by 0.05 M EDTANa₂H₂ solution and reused. SGIV was shown to be perspective for determination of aluminum in solution in the range of 0.01-0.13 mg L⁻¹ by solid phase luminescent technique.     

The novel azomethine ligands for binuclear copper(II) complexes with ferro- and antiferromagnetic properties

A series of novel binuclear ferro- and antiferromagnetic Cu(2+) chelates of structurally broadly varied Schiff bases (derived from o-tosylamino(hydroxyl)benzaldehydes and monoalkylated o-phenylenediamine, o-aminophenol, o-aminothiophenol, 1,2-diaminobenzimidazole, 1-aminobenzimidazoline-2-thione) and β-diketimines (derived from 2,6-di-i-Pr-aniline) has been prepared. The tautomerism of the ligands and structureof their copper complexes have been studied with the use of IR, ¹H NMR EPR and EXAFS spectroscopy. Molecular and crystal structure of a β-diketimine copper dimer has been determined by X-ray crystallography. The magnetic measurements (2–300?K) performed for all the complexes showed that the ferro- and antiferromagnetic character of the exchange interaction depends both on the structure of the coordination site (origin of the ligating centers) and the structure of the ligands (in particular, on the type of the cycle annelated to the bridging fragment). Whereas S-binding metal chelates 13 (X?=?NTs, Y?=?S, R?=?H) are diamagnetic, the complexes 15 with annelated azole moieties are ferromagnetic.     

Epoxidation of cyclooctene using soluble or MCM-41-supported molybdenum tetracarbonyl-pyridylimine complexes as catalyst precursors

The ligand N-(n-propyl)-2-pyridylmethanimine (pyim) and an immobilised analogue of this ligand (MCM-41-pyim) were prepared by the condensation reaction of 2-pyridinecarboxaldehyde with either propylamine or aminopropyl groups covalently attached to the ordered mesoporous silica MCM-41. Free and immobilised tetracarbonyl complexes of the type cis-[Mo(CO)₄(L)] (L = pyim (1), MCM-41-pyim) were then prepared by microwave-assisted heating of a mixture of Mo(CO)₆ and the organic ligand or ligand-silica in toluene at 110 °C for 30-45 min. The products were characterised by NMR spectroscopy (¹H, ¹³C and ²⁹Si, in solution and in the solid state), elemental analysis, N₂ adsorption, and FT-IR spectroscopy. When used as catalyst precursors for the epoxidation of cis-cyclooctene by tert-butylhydroperoxide at 55 °C (1 mol% catalyst (Mo), no additional co-solvent), 1,2-epoxy-cyclooctane was obtained as the only reaction product in quantitative yield after 5 h for 1 and 36% yield after 24 h for the supported complex. The use of the ionic liquid (IL) 1-butyl-3-methylimidazolium tetrafluoroborate as co-solvent led to lower catalytic activities (epoxide selectivity was always 100%) but allowed the catalyst/IL mixtures (homogeneous mixture for IL+1 and a biphasic solid + IL system for IL+MCM-41-pyim/Mo) to be easily recovered and reused in subsequent runs without loss of catalytic performance.     

Cobalt(II), nickel(II) AND zinc(II) dicarboxylate complexes with hydrazine as bridged ligand

The complexes of chromium and molybdenum with salicylidene-2-aminophenol (shaH₂), salicylidene-2-aminoanisole (salanH₂), salicylidene-2-aminoaniline (salphenH₂) and biquinoline (biq) were studied using the thermogravimetric techniques. The thermal decomposition of all complexes was found to be first order reaction and the thermodynamic parameters corresponding to the different decomposition steps were reported. Molybdenum complexes were found to be more thermally stable and the order of stability was [Mo(CO)₄(biq)]>[MoO(salphen)]>[MoO₂(salphenH)₂]>[MoO₄(salan)₂]>[MoO(sha)]. Similar trend was found for chromium complexes where [Cr(CO)₄(biq)]>[Cr(CO)₂(salphen)] >[CrO₂(CO)₂(shaH₂)]>[CrO₂(CO)₂(salan)₂].     

Synthesis,characterization and biological screening studies of mixed ligand complexes using flavonoids as precursors

Flavonoids are a group of plant phenolics that provide various health benefits through cell signalling pathways and antioxidant effects. In the present study, a new series of mixed ligand complexes of Co(II), Ni(II), Cu(II) and Zn(II) were synthesized by incorporating curcumin and quercetin flavonoid precursors. The structural features of the synthesized complexes were explored using elemental analysis, thermogravimetric analysis, UV–visible, infrared, NMR, mass and electron paramagnetic resonance spectral analyses and conductivity measurements. These data support an octahedral geometry of the synthesized complexes. In silico biological activity score for the ligand was predicted using PASS online software. ADMET properties were studied using VLS3D online software. Anti‐inflammatory and antioxidant activities were experimentally validated which prove that theoretical predictions are in agreement with the experimental results. Interestingly the synthesized complexes interact with calf thymus DNA through groove binding mode. Moreover, they have good potential to cleave pUC19 DNA. Minimum inhibitory concentration values of the synthesized complexes reveal that they have better antimicrobial efficacy than the ligands.