Rheology and rheokinetics of triethanolamine modified carboxymethyl hydroxyethyl cellulose

To meet requirements of fracturing fluid thickener, triethanolamine was used to modify carboxymethyl hydroxyethyl cellulose (CMHEC) to obtain product called T-CMHEC of high viscosity. Rheological properties of CMHEC and T-CMHEC solutions were investigated to compare its structure and rheological performance, including viscosity, flow curve, thixotropy, and viscoelasticity. Viscosities of CMHEC and T-CMHEC solutions are, respectively, 19.0 and 63.2?mPa?·?s for the same concentration of 0.3%. Viscosity of T-CMHEC solutions is 3.3 times of CMHEC ones. Besides, the thixotropy and viscoelasticity of T-CMHEC system are both getting stronger than before. In summary, the T-CMHEC system shows better rheological performance after modification. Crosslinking process of T-CMHEC system is investigated under steady shear under different conditions, containing shear rates, concentrations of crosslinking agent, concentrations of pH adjuster, and temperature. Viscosity curves changing with time are obtained during crosslinking process. Four-parameter crosslinking rheokinetics equation is suitable to fit the viscosity curves under different conditions. Study on crosslinking process of T-CMHEC solutions is helpful to deepen the understanding on gel formation, and provides a theoretical basis for its application.     

Rheological properties of hexadecyl dimethyl amine modified carboxymethyl hydroxyethyl cellulose solutions and its gelling process

To obtain a new fracturing fluid viscosifier, hexadecyl dimethyl amine was used to modify carboxymethyl hydroxyethyl cellulose (CMHEC) to obtain a product called HD-CMHEC with high viscosity. The rheological properties of HD-CMHEC solutions and CMHEC solutions were studied. For the concentration of 0.3%, the viscosity of CMHEC and HD-CMHEC solutions is, respectively, 19.0?mPa?·?s and 73.6?mPa?·?s, respectively. The viscosity of HD-CMHEC solution increases 2.8 times than before. The thixotropy and viscoelasticity of HD-CMHEC solutions become stronger. As a typical viscoelastic fluid, HD-CMHEC solutions show better rheological performance than that of CMHEC solutions. The gelling process of HD-CMHEC solutions under steady shear was studied in detail. The concentrations of HD-CMHEC solutions, shear rates, and crosslinking agent were investigated. Viscosity versus time curves during the crosslinking process were obtained. The four-parameter crosslinking rheokinetics equation can describe the gelling process of HD-CMHEC solutions under different conditions well. Study on the gelling process of HD-CMHEC solutions under steady shear contributes to the understanding of gel formation, and provides theoretical guidance for exploration and exploitation of the system.     

Preparation and characterization of hybrid cationic hydroxyethyl cellulose/sodium alginate polyelectrolyte antimicrobial films

This study aimed to develop polyelectrolyte‐structured antimicrobial food packaging materials that do not contain any antimicrobial agents. Cationic hydroxyethyl cellulose was synthesized and characterized by Fourier‐transform infrared, ¹H NMR, and ¹³C NMR spectroscopy. Its nitrogen content was determined by Kjeldahl method. Polyelectrolyte‐structured antimicrobial food packaging materials were prepared using hydroxyethyl cellulose, cationic hydroxyethyl cellulose, and sodium alginate. Antimicrobial activity of materials was defined by inhibition zone method (disc diffusion method). Thermal stability of samples was evaluated by thermal gravimetric analysis and differential scanning calorimetry. Surface morphology of samples was investigated by SEM. The obtained results prove that produced food packaging materials have good thermal and antimicrobial properties, and they can be used as food packaging material in many industries.     

十二烷基硫酸钠与羟乙基纤维素的相互作用

本文用表面张力(γ)和电导率(κ)方法研究了阴离子表面活性剂十二烷基硫酸钠(SDS)与天然纤维素的水溶性改性物羟乙基纤维素(HEC)的相互作用.实验结果表明,SDS-HEC溶液的γ-lgcSDS曲线和κ～CSDS曲线均呈现双拐点特征,并且γ-lgcSDS曲线上两个SDS临界浓度值(c1 )γ及(c2)γ,与κ～CSDS...     

2,4-D/CMC-g-AM/SA/FK微球的制备及其缓释性能

以丙烯酰胺(AM)为单体,制备了羧甲基纤维素钠接枝丙烯酰胺共聚物(CMC-g-AM)。以2,4-二氯苯氧乙酸(2,4-D)为模型药物,以羽毛蛋白(FK)为共混改性剂,采用挤压法制备了CMC-g-AM/海藻酸钠(SA)/羽毛蛋白载药微球。利用红外光谱、光学显微镜、激光粒度仪分别对接枝共聚物的结构、载药微球的形貌以及粒径分布进行了表征,并探讨了不同的接枝共聚物、羽毛蛋白用量、交联剂浓度和交联时间对缓释微球的载药量和缓释性能影响。结果表明,当CMC-g-AM的合成单体比AM:CMC为3:1,羽毛蛋白用量为30%,交联剂浓度为0.7 mol·L-1,交联时间为1 h,载药微球的载药量较高,为16.7%。复合微球平均粒径为1.6 mm。载药微球具有良好的缓释性能,释药曲线符合Higuchi动力学方程。     

羟乙基纤维素接枝N-异丙基丙烯酰胺的研究

利用硝酸铈铵引发了羟乙基纤维素与N-异丙基丙烯酰胺的接枝反应.通过红外光谱和1H-NMR谱证明了接枝反应是成功的讨论了单体浓度、引发剂浓度、反应温度对接枝共聚反应的影响。通过差示扫描量热仪和动态激光光散射仪。研究了接枝产物的溶液性质,证明了接枝产物具有温敏性。     

Studies on the molecular flexibility of novel dendronized carboxymethyl cellulose derivatives

Water-soluble deoxy-azido cellulose derivatives were synthesized by heterogeneous carboxymethylation, applying 2-propanol/aqueous NaOH as slurry medium. The novel, carboxymethyl deoxy-azido cellulose provides a convenient starting material for the selective dendronization of cellulose via the copper-catalyzed Huisgen reaction yielding water-soluble carboxymethyl 6-deoxy-(1-N-[1,2,3-triazolo]-4-polyamidoamine) cellulose derivatives of first (degree of substitution, DS 0.51), second (DS 0.44) and third generation (DS 0.39). The novel biopolymer derivatives were characterized by FT-IR and NMR spectroscopy, intrinsic viscosity, sedimentation coefficient and weight average molar mass. Solution conformation and flexibility were estimated qualitatively using conformation zoning and quantitatively (persistence length) using the combined global method. Sedimentation conformation zoning showed a semi-flexible coil conformation and the global method applied to each carboxymethyl deoxy-azido cellulose and carboxymethyl 6-deoxy-(1-N-[1,2,3-triazolo]-4-polyamidoamine) cellulose derivative yielded persistence length all within the range of 2.8-4.0 nm with no evidence of any change in flexibility with dendronization.     

Thermal behavior of polystyrene synthesized in the presence of carboxymethyl cellulose

Summary Study of the decomposition kinetics is an important tool for the development of polymer recycling in industrial scale. In this work, parameters such as activation energy, frequency factor and reaction order, were measured under dynamic conditions. Flynn-Wall-Ozawa, Van Krevelen, Horowitz-Metzger, Coats-Redfern, Madhusudanan and Vyazovkin methods were used to determine the kinetic parameters. The analysis of the results obtained by the Coats-Redfern method shows that the thermal degradation process of LDPE and HDPE corresponds to a phase boundary controlled reaction (mechanism R2). This method shows that the reaction order values of LDPE and HDPE are about 0.7 and 0.6, respectively.     

Controlling the water content of never dried and reswollen bacterial cellulose by the addition of water-soluble polymers to the culture medium

For the modification of medically useful biomaterials from bacterially synthesized cellulose, fleeces of Acetobacter xylinum have been produced in the presence of 0.5, 1.0, and 2.0% (m/v) carboxymethylcellulose (CMC), methylcellulose (MC), and poly(vinyl alcohol) (PVA), respectively, in the Hestrin-Schramm culture medium. The incorporation of the water-soluble polymers into cellulose and their influence on the structure, crystal modifications, and material properties are described. With IR and solid-state ¹³C NMR spectroscopy of the fleeces, the presence of the cellulose ethers and an increase in the amorphous parts of the cellulose modifications (NMR results) have been detected. The incorporation is represented by a higher product yield, too. As demonstrated by scanning electron microscopy, a porelike cellulose network structure forms in the presence of CMC and MC. This modified structure increases the water retention ability (expressed as the water content), the ion absorption capacity, and the remaining nitrogen-containing residues from the culture medium or bacteria cells. The water content of bacterial cellulose (BC) in the never dried state and the freeze-dried, reswollen state can be controlled by the CMC concentration in the culture solution. The freeze-dried, reswollen BC-CMC (2.0%) contains 96% water after centrifugation, whereas standard BC has only 73%. About 98% water is included in a BC-MC composite in the wet state, and about 93% is included in the reswollen state synthesized in the presence of 0.5, 1.0, or 2.0% MC. These biomaterial composites can be stored in the dried state and reswollen before use, reaching a higher water absorption than pure, never dried BC. The copper ion capacity of BC-CMC composites increases proportionally with the added amount of CMC. BC-CMC (0.5%) can absorb 3 times more copper ions than original BC. In the case of 0.5 and 1.0% PVA additions to the culture solution, this polymer cannot be detected in the cellulose fleeces after they are washed. Nevertheless the presence of PVA in the culture medium effects a decreased product yield, a retention of nitrogen-containing residues in the material during purification, a reduced water absorption ability, and a slightly higher copper ion capacity in comparison with original BC. The water content of freeze-dried, reswollen BC-PVA (0.5%) is only 62%. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 463–470, 2004     

Influence of cellulose type on the properties of extruded pellets. Part I. Physicochemical characterisation of the cellulose types after homogenisation

 The physicochemical properties of different types of powdered cellulose (PC) and microcrystalline cellulose (MCC) were studied by examining the changes in particle size, viscosity and specific surface area after a homogenisation process. An additional characterisation was carried out using X-ray diffractometry. A preliminary investigation using a type of MCC showed that increasing the homogenisation pressure and the number of passage cycles led to a significant decrease in the particle size and simultaneously to a remarkable increase in the specific surface area and viscosity. Most MCC types showed the same pattern during the homogenisation process. “Colloidal” MCC displayed a higher viscosity than the others but without significant change in the viscosity after different homogenisation cycles. In contrast to this behaviour of the MCCs, the PCs showed no remarkable change in the particle size but did show a marked change in their viscosity. Furthermore, only MCC suspensions, with the exception of “colloidal” MCC, agglomerated after the homogenisation process, whereas this was not seen in the PC suspensions. Hence, since the MCC types as well as the PC types originally had the same chemical structure, this different behaviour among these types can only be attributed to their different physical properties. Received: 27 July 1999/Accepted: 15 December 1999     

A new study of the enzymatic hydrolysis of carboxymethyl cellulose with a bulk acoustic wave sensor

A new bulk acoustic wave (BAW) cellulase sensing technique, which is based on the enzymatic hydrolysis process of sodium carboxymethylcellulose (CMC) by cellulase, was established. The frequency shift curves of BAW sensor indicated that the viscosity of the tested solutions decreased during the hydrolysis process. The hydrolysis rate of CMC by cellulase was calculated from the frequency shift curves. The hydrolysis rate of CMC under different pH conditions at 30°C showed that cellulase had high hydrolysis ability approximately at pH 5.0. Kinetic parameters (the Michaelis constant K_m and the maximum rate V_max) of the process were estimated by using a linear method of Lineweaver–Burk plot. K_m is 1.95±0.25 mg ml⁻¹ and V_max is −(4.25±0.58)×10⁻³ g^1/2 cm^−3/2 cP^1/2 min⁻¹. Also the activation energy (E_a) of the enzymatic hydrolysis, with a value of 51.99±1.26 kJ mol⁻¹, was estimated in this work.     

Investigating the kinetics of the adsorption process of polyamideamine on cellulose

The kinetic dependences have been investigated of the adsorption process of polyamideamine on monocarboxyl cellulose, bleached sulphate cellulose pulp of softwood and bleached sulphite cellulose pulp of hardwood. It has been found that the process kinetics can be described by means of the Elovich-Tyomkin exponential kinetic equation; the influence of the entropy factors plays a decisive role in changing the process speed; the activation energy is of the order of 6.5–8.0 kJ/mol.     

Effect of the reaction conditions on the degree of substitution of carboxymethyl cellulose

Cellulosic fabric composed of 84 % cotton and 16 % viscose rayon fiber was carboxymethylated. The influence of the reaction parameters (concentration of the reagents, time of reaction) on the degree of substitution was studied in the process, applying sodium hydroxide and monochloroacetic acid in one bath. Two kinds of regression equations were used to calculate approximately the degree of substitution. These polynomials can be used for the selection of reaction parameters to obtain a sample of a given degree of substitution.     

The effect of adsorbed carboxymethyl cellulose on the cotton fibre adsorption capacity for surfactant

The research reported in this paper demonstrates that the capacity of cotton fibres to adsorb cationic surfactants as well as the rate of the adsorption process can be increased by adsorbing carboxymethyl cellulose (CMC) onto the fibre surfaces; in addition, the adsorption can be restricted to the fibre surface. CMC was deposited by means of adsorption from an aqueous solution. The adsorption of N-cetylpyridinium chloride (CPC) from an aqueous solution onto the CMC-modified fibres was measured using UV-spectrometric determination of the surfactant concentration in the solution. Adsorption onto the cotton fibres was studied in a weakly basic environment (pH 8.5) where cotton fibres are negatively charged and the CPC ion is positively charged. Modification of the fibres by adsorption of CMC introduces new carboxyl groups onto the fibre surfaces, thereby increasing the adsorption capacity of the fibres for CPC. The initial rate of adsorption of CPC increased proportionally with the amount of charge; however, this rate slowed down at high degrees of coverage on fibres with a high charge. The adsorption of cationic surfactant to the anionic surface groups was stoichiometric, with no indication of multilayer or admicelle formation. It was evident that the acidic group content of the fibres was the primary factor determining cationic surfactant adsorption to these fibres.     

Carboxymethyl cellulose as a green and biodegradable catalyst for the solvent-free synthesis of benzimidazoloquinazolinone derivatives

Carboxymethyl cellulose (CMC) was used as an efficient, and environmentally friendly catalyst for the solvent-free three-component synthesis of quinazolinone derivatives by condensation of 2-aminobenzimidazole, dimedone or 1,3-cyclohexanedione, and different aldehydes. The catalyst was recovered easily, and reused without significant loss of its activity. Solvent-free and mild reaction conditions, nontoxic-, biodegradable-, and inexpensive catalyst, environmentally benign method, and high to excellent yields are some important features of this protocol.     

An insight into the process of tablet formation of microcrystalline cellulose

The present paper aims to show whether the shrinking of the microcrystalline cellulose (MCC) tablets can be derived from underlying processes and whether these processes can be visualized on a nanoscale level. Tableting of MCC was performed on an instrumented eccentric tableting machine to a maximum relative density (ρ_rel,max) of 0.90 of the tablets. The apparent density of the tablets was analyzed by helium pycnometry after tableting. The breaking surface of a MCC tablet was analyzed directly after tableting continuously by video in an environmental scanning electron microscope (ESEM) at constant humidity. Further the breaking surface was analyzed by transmission electron microscopy (TEM) after freeze fracturing. The results show that firstly apparent density by helium pycnometry increases after tableting and that secondly inside the tablet the fiber strength decreased while also the gaps between the fibers increased as was visualized by ESEM. Further the results by TEM indicate that the decrease in fiber strength is caused by a parallel orientation of the MCC microcrystals which is induced by a mechanical activation due to tableting. In conclusion the measured shrinking MCC tablets after tableting is caused by processes on a nanoscale level.     

In vitro and in vivo evaluations of nanofibrous nanocomposite based on carboxymethyl cellulose/polycaprolactone/cobalt-doped hydroxyapatite as the wound dressing materials

These days, Ophthalmic wound treatment is a major problem; due to its nature, bio/materials are the best choices as wound dressing materials. The main objective of the current survey is to develop and investigate effective wound dressing materials for skin care applications. In these ways, we combined the good biological properties of Cobalt-doped hydroxyapatite particles (CoHAp) with the structural properties of Polycaprolactone (PCL)/ carboxymethyl cellulose (CMC) nanofibers. Electrospinning and co-precipitation methods were used to synthesize nanofibers and CoHAp particles, respectively. Nanocomposites were synthesized in the absence and different percentages of CoHAp. The PCL/CMC, PCL/CMC/CoHA 5 %, PCL/CMC/CoHA 10 %, and PCL/CMC/CoHA 15 % formulated nanocomposites have the diameter of 383 ± 50, 391 ± 84, 441 ± 65, and 495 ± 99 nm, respectively. The synthesized nanofibrous wound dressing porosity and water absorption capacity were in the range of 40 to 60 % and 32 to 63 %, respectively. Hemo and cytocompatibility of the nanofibrous wound dressing were analyzed by in vitro evaluation, and the results were satisfactory and the structures were fully biocompatible. The PCL/CMC/CoHA 10 % wound dressing, were selected as the best nanocomposites for wound healing based on our animal studies on the healing outcomes. The results showed that the PCL/CMC nanofibers-Cobalt-doped HAp wound dressing is an effective bioactive nano-biomaterials for the wound healing process.     

Maleic anhydride incorporated onto cellulose and thermodynamics of cation-exchange process at the solid/liquid interface

This investigation explores the chemical modification of cellulose by using a quasi solvent-free procedure, in which the biopolymer was added to molten maleic anhydride, producing a mixture of maleated and fumarated celluloses. Using this pathway mainly surface modifications are observed and more than 2.82 ± 0.05 mmol of modifier per gram of synthesized polymer were obtained. These chemically modified materials were characterized by elemental analysis, solid-state ¹³C NMR CP/MAS, FTIR, XRD, TG and SEM. The chemically modified polysaccharides are able to adsorb cations. The data were adjusted to a modified Langmuir equation to give 1.75 ± 0.09 and 2.40 ± 0.12 mmol/g of Co²⁺ and Ni²⁺, respectively. The net thermal effects obtained from calorimetric titration measurements were also adjusted to a modified Langmuir equation and the enthalpy of the interaction was calculated to give the endothermic values of 0.29 ± 0.02 and 0.87 ± 0.02 kJ/mol for Co²⁺ and Ni²⁺, respectively. The thermodynamic data for these systems are favorable for cation adsorption from aqueous solutions at the solid/liquid interface, suggesting the use of this anchored biopolymer for cation removal from the environment.     

Effect of hydroxypropylmethyl cellulose on the complexation of diclofenac with cyclodextrins

The effect of a hydrophilic polymer, hydroxypropylmethyl cellulose K4M, on the complexation of diclofenac sodium with b- and hydroxypropyl-b-cyclodextrins has been studied. Multicomponent systems were prepared with the drug, both cyclodextrin and the polymer. Phase solubility diagrams revealed the positive effect of the polymer on the complexation of the drug but this effect was found after autoclaving the solutions. Solid inclusion complexes were prepared by freeze-drying and characterized by thermal analysis (DSC) and X-ray diffractometry. In solid state, binary inclusion complexes enhance the dissolution behaviour of diclofenac but, from the b-cyclodextrin multicomponent complex, the polymer controls the release of the drug. In the case of hydroxy- propyl-b-cyclodextrin multicomponent system, the solubility of the drugs increases significantly compared with the binary complex. This revised version was published online in July 2006 with corrections to the Cover Date.