Chemically activated Ipomoea carnea as an adsorbent for the copper sorption from synthetic solutions

An indigenously prepared zinc chloride activated Ipomoea carnea (morning glory), a low-cost and abundant adsorbent, was used for removal of Cu(II) ions from aqueous solutions in a batch adsorption system. The chemical activating agent ZnCl₂ was dissolved in deionised water and then added to the adsorbent in two different ratios 1:1 and 1:0.5 adsorbent to activating agent ratio by weight. Studies were conducted as a function of contact time, initial metal concentration, dose of adsorbent, and pH. Activated Ipomoea carnea (AIC) were characterised using scanning electron microscopy (SEM), iodine number and methylene blue number. High iodine numbers indicates development of micro pores with zinc chloride activation. Maximum adsorption was noted within pH range 6.0(±0.05). Adsorption process is fast initially and reaches equilibrium after about 4 hours. The kinetic data were analysed using pseudo-first-order and pseudo-second-order models. The pseudo-second-order kinetic model was found to agree well with the experimental data. Adsorption equilibrium data were analyzed using Langmuir and Freundlich isotherm models. The Langmuir model represented the sorption process better than the Freundlich model. Based on the Langmuir isotherm, the monolayer adsorption capacity of Cu(II) ions was 7.855 mg?g^?1 for AIC (1:1) and 6.934 mg?g^?1 for AIC (1:0.5).     

Dye Pollutants removal from Waste water using Metal Oxide Nanoparticle embedded Activated Carbon: An Immobilization study

This study evaluated the feasibility of Rhodamine-B dye (Rh B) removal from aqueous solution, using Lead-Iron Oxide nanoparticles Loaded Activated Carbon (FePbO@AC). The parameters like pH, contact time, adsorbent/adsorbate dosage and temperature on adsorption was studied. Optimized conditions are pH of 7.0, 25?min contact time, 50?ppm of dye concentration and 200?mg of adsorbent concentration. The kinetics of adsorption was calculated using pseudo-first-order, pseudo-second-order, and intra-particle diffusion models. The calculations revealed that the pseudo-second-order kinetic equation best-fit the adsorption data. The Langmuir isotherm model best fit the equilibrium data. The maximum sorption capacity (Q_max) for dye is 1000?mg Rh B/g FePbO@AC. Change in entropy (ΔS), Gibb’s free energy change (ΔG), and enthalpy (ΔH) were calculated for the adsorption of Rh B dye.     

Removal and recovery of uranium from aqueous solution by tea waste

Experiments on the removal and recovery of U(VI) from aqueous solution by tea waste were conducted. The adsorbent was characterized by scanning electron microscope and energy dispersive spectrometer before and after the adsorption treatment. The removal of U(VI) amounts to 86.80?% at optimum pH 6. The adsorption process reaches its equilibrium in 12?h at 308?K, and the kinetic characteristic can be described by the pseudo-second-order kinetic equation. The amount of adsorption increases from 22.92 to 142.21?mg?g^?1 with the decrease of tea waste dosage from 100 to 10?mg for solution with an initial uranium concentration of 50?mg?L^?1. Desorption for the four strippants is higher than 80?%. The equilibrium data are more agreeable with Freundlich isotherm than Langmuir isotherm.     

Equilibrium,kinetic and thermodynamic biosorption studies of Hg(II) on red algal biomass of Porphyridium cruentum

Among a variety of microbial materials employed for biosorption, algae have added advantages of non-toxic and autotrophic nature. In this study, biosorption of Hg(II) was studied with red algal biomass of Porphyridium cruentum. The parameters affecting biosorption such as dosage of biosorbent, pH, contact time, initial metal concentration, temperature and effect of foreign metal cations in binary system were evaluated. Kinetic data were described with the help of pseudo-first-order and pseudo-second-order kinetic models. Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models were applied to adsorption equilibrium data. According to the results, the maximum removal capacity (q_max) was 2.62?mg/g observed at pH 7 with 0.25?g/L of biosorbent dosage for Hg(II) solution containing 10?mg/L of metal ions. The Langmuir isotherm model fits best to the adsorption data while the kinetic data followed the pseudo-second-order model. Thermodynamics studies showed that the biosorption process of Hg(II) on P. cruentum was exothermic in nature.     

Amin-functionalized magnetic-silica core-shell nanoparticles for removal of Hg2+ from aqueous solution

Magnetic nanoparticles with monodisperse shape and size were prepared by a simple method and covered by silica. The prepared core-shell Fe₃O₄@silica nanoparticles were functionalized by amino groups and characterized by scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer-Emmett-Teller (BET) and Fourier transform infrared spectroscopy (FT-IR) techniques. The synthesized nanoparticles were employed as an adsorbent for removal of Hg²⁺ from aqueous solutions, and the adsorption phenomena were studied from both equilibrium and kinetic point of views. The adsorption equilibriums were analyzed using different isotherm models and correlation coefficients were determined for each isotherm. The experimental data were fitted to the Langmuir–Freundlich isotherm better than other isotherms. The adsorption kinetics was tested for the pseudo-first-order, pseudo-second-order and Elovich kinetic models at different initial concentrations of the adsorbate. The pseudo-second-order kinetic model describes the kinetics of the adsorption process for amino functionalized adsorbents. The maximum adsorption occurred at pH 5.7 and the adsorption capacity for Fe₃O₄@silica-NH₂ toward Hg²⁺ was as high as 126.7 mg/g which was near four times more than unmodified silica adsorbent.     

Adsorption isotherm for uranyl biosorption by Saccharomyces cerevisiae biomass

Biosorption of uranyl ions from aqueous solution by Saccharomyces cerevisiae was studied in a batch system. The influence of contact time, initial pH, temperature and initial concentration was investigated. The optimal conditions were found to be 3.5?h of contact time and pH?=?4.5. Temperature had no significant effect on adsorption. The uptake of uranyl ions was relatively fast and 85?% of the sorption was completed within 10?min. The experimental data were well fitted with Langmuir isotherm model and pseudo-second order kinetic model. According to this kinetic model, the sorption capacity and the rate constant were 0.455?mmol UO₂ ²⁺/g dry biomass and 1.89?g?mmol^?1?min^?1, respectively. The Langmuir isotherm indicated high affinity and capacity of the adsorbent for uranyl biosorption with the maximum loading of 0.477?mmol UO₂ ²⁺/g dry weight.     

Design and evaluation of functionalized multi-walled carbon nanotubes by 3-aminopyrazole for the removal of Hg(II) and As(III) ions from aqueous solution

Carboxylated multi-walled carbon nanotubes (MWCNTs-COOH) were chemically modified with 3-aminopyrazole (MWCNTs-f) and applied as an efficient adsorbent to mercury and arsenic adsorption from aqueous solutions. The adsorbents were characterized by FT-IR, EDX, FE-SEM, TGA, and BET. The effects of pH, adsorbent dose, and initial ions concentration on the adsorption efficiency and the optimum conditions were investigated by central composite design. The optimum conditions were obtained at pH 7.6–7.9, adsorbent dose 20 mg, and initial ions concentration 20 ppm. So the maximum adsorption efficiencies in these conditions were 80.5 and 72.4% for the removal of Hg(II) and As(III) by MWCNTs-f, respectively. The quadratic model was used for the analysis of variance and indicated that adsorption of metal ions strongly depends on pH. Also, the pseudo-second-order model has been achieved from the adsorption kinetic studies. Furthermore, the experimental data were well fitted to the Langmuir isotherm and the maximum adsorption capacities obtained were 112 and 133 mg g^?1 for the adsorption of Hg(II) and As(III) by MWCNTs-f, respectively. Moreover, a thermodynamic study revealed that the adsorption reactions were spontaneous and endothermic with the increase in randomness. In addition, a desorption study showed the favorable regeneration ability of MWCNTs-f even after three adsorption–desorption cycles. Therefore, the MWCNTs-f adsorbent has good potential for the removal of Hg(II) and As(III) pollutants from aqueous solutions.     

Synthesis, characterization, thermodynamic and kinetic investigations on uranium (VI) adsorption using organic-inorganic composites: Zirconyl-molybdopyrophosphate-tributyl phosphate

Zirconyl-molybdopyrophosphate-tributyl phosphate (ZMPP-TBP) was a novel organic-inorganic composite adsorbent prepared by co-precipitation method and used in the adsorption of uranium from aqueous solution in batch adsorption experiments. The as-obtained product was characterized using SEM, energy dispersive X-ray spectroscopy (EDX), XRD and BET-N₂ adsorption measurements. The study had been conducted to investigate the effects of solution pH, temperature, contact time, initial concentration and coexisting ions. A maximum removal of 99.31% was observed for an initial concentration 5 mg/L, at pH 6.0 and an adsorbent dose of 1.0 g/L. The isothermal data were fitted with both Langmuir and Freundlich equations, but the data fitted the former better than the latter. According to the evaluation using the Langmuir equation, the maximum adsorption capacity of uranium (VI) was 196.08 mg/g at 293 K and pH 6.0. The pseudo-first-order kinetic model and pseudo-second-order kinetic model were used to describe the kinetic data, and the pseudo-second-order kinetic model was better. The thermodynamic parameter ΔG was calculated, the negative ΔG values of uranium (VI) at different temperature showed that the adsorption process was spontaneous. The good reusability of ZMPP-TBP also indicated that the ZMPP-TBP was a very promising adsorbent for uranium adsorption from aqueous solution.     

Adsorption of Copper (II) Ions onto Surfactant-Modified Oil Palm Leaf Powder

Il palm leaf powder (OPLP), an agricultural solid waste was used as adsorbent for the removal of copper (II) ions after modification with an anionic surfactant, sodium dodecyl benzene sulfonate (SDBS), CH₃(CH₂)₁₁C₆H₄SO₃Na. The copper (II) ions adsorption is highly dependent on pH and maximum removal was observed at pH 6, above which copper (II) started to precipitate. The equilibrium adsorption data were fitted into the Langmuir and Freundlich isotherms. The Freundlich isotherm model fitted well to data with 0.989 regression coefficient (R²). The kinetics of the adsorption of copper (II) ions onto the surfactant-modified OPLP was best described by a pseudo-second-order model. Comparison of this SDBS-modified-OPLP to previously investigated adsorbents showed comparably good result, offering this material as a promising adsorbent for the treatment of waste waters containing lower concentrations of copper (II) ions.     

Removal of Th(IV), Ni(II)and Fe(II) from aqueous solutions by a novel PAN–TiO<Subscript>2</Subscript> nanofiber adsorbent modified with aminopropyltriethoxysilane

A novel polyacrylonitrile (PAN)–titanium oxide (TiO₂) nanofiber adsorbent functionalized with aminopropyltriethoxysilane (APTES) was fabricated by electrospinning. The adsorbent was characterized by SEM, FTIR, TEG and BET analyses. The pore diameter and surface area of the adsorbent were 3.1 nm and 10.8 m² g^?1, respectively. The effects of several variables, such as TiO₂ and amine contents, pH, interaction time, initial concentration of metal ions, ionic strength and temperature, were studied in batch experiments. The kinetic data were analyzed by pseudo-first-order, pseudo-second-order and double-exponential models. Two isotherm models, namely Freundlich and Langmuir, were used for analysis of equilibrium data. The maximum adsorption capacities of Th(IV), Ni(II) and Fe(II) by Langmuir isotherm were found to be 250, 147 and 80 mg g^?1 at 45 °C with pH of 5, 6 and 5, respectively, and greater adsorption of Th(IV) could be justified with the concept of covalent index and free energy of hydration. Calculation of ΔG°, ΔH° and ΔS° demonstrated that the nature of the Th(IV), Ni(II) and Fe(II) metal ions adsorption onto the PAN–TiO₂–APTES nanofiber was endothermic and favorable at a higher temperature. The negative values of ΔG° for Th(IV) showed that the adsorption process was spontaneous, but these values for Ni(II)and Fe(II) were positive and so the adsorption process was unspontaneous. Increasing of ionic strength improved the adsorption of Ni(II) and Fe(II) on nanofiber adsorbent but decreased the adsorption capacity of Th(IV). The adsorption capacity was reduced slightly after six cycles of adsorption–desorption, so the nanofiber adsorbent could be used on an industrial scale. The inhibitory effect of Ni(II) and Fe(II) on the adsorption of Th(IV) was increased with an increase in the concentration of inhibitor metal ions.     

Validation of a Monte Carlo HPGe detector model against irradiated foil gamma-ray spectroscopy measurements

In order to separate and pre-concentrate uranium from aqueous phase, a novel silica-based adsorbent was prepared by impregnating nalidixic acid (HNA) into a macroreticular silica/polymer composite support (SiO₂-P) with a mean diameter of 60 μm. Adsorption behavior of uranium from aqueous solution onto the adsorbent was studied. Experimental results indicated that HNA/SiO₂-P showed strong adsorption for uranium in a wide range of pH from 3.5 to 10.0, and the maximum adsorption capacity was 35.4 mg g⁻¹. In addition, HNA/SiO₂-P exhibited good selectivity for U(VI) and showed weak or bare adsorption affinity to foreign ions. Kinetic and isotherm of uranium adsorption were in accordance with the pseudo-second-order kinetic model and Langmuir isotherm adsorption model, respectively. Moreover, U(VI) sorption was found to be an endothermic reaction and spontaneous under experimental state. The synthesized adsorbent showed an admirable stability at lower pH values in aqueous solution.

     

Adsorption of Pb(II) and Ni(II) From Aqueous Solution by a High-Capacity Industrial Sewage Sludge-Based Adsorbent

In the present study, adsorption of Ni(II) and Pb(II) from aqueous solution was investigated using activated carbon synthesized with industrial wastewater sludge. The synthesized adsorbent was analyzed using nitrogen adsorption–desorption and Fourier transfer infrared (FTIR) techniques. Batch adsorption mode was used to evaluate the effect of solution pH, contact time, adsorbent dose, initial metal ion concentration, and temperature on the adsorption capacity of the synthesized adsorbent. The kinetic data were analyzed using different kinetic models. The pseudo-second-order equation gave the best fit to the experimental data for both metal ions. The equilibrium isotherm data were analyzed using the Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) isotherm models. The results showed that the data obtained for the Ni(II) and Pb(II) adsorption are in good agreement with the Langmuir model. The Langmuir mono-layer maximum adsorption capacities for Ni(II) and Pb(II) ions were estimated to be 74.06 and 88.76 mg g^?1 at 25°C, respectively. In addition, the thermodynamic studies proved that the adsorption process of both metals could be considered endothermic.     

Adsorptive removal of malachite green and Rhodamine B dyes on Fe3O4/activated carbon composite

This study demonstrates the adsorption experiments of toxic dyes malachite green (MG) and Rhodamine B (RB) on Fe₃O₄-loaded activated carbon (AC). AC, which is known to be a high-capacity adsorbent, was aimed to be easily separated from aqueous media by loading it with Fe₃O₄. Fe₃O₄-loaded AC was prepared by the coprecipitation method and named magnetic activated carbon (M-AC), and the produced M-AC was characterized by x-ray diffraction (XRD), thermogravimetric analysis (TGA), and pH_pzc analyses. MG and RB adsorption by the M-AC was performed separately by batch technique and the effects of adsorbent amount, solution pH, and initial dye concentration on the adsorption were explored. Maximum removal efficiencies were found to be 96.11% for MG and 98.54% for RB, and the Langmuir isotherm model was the most fitted isotherm model for the adsorption. The kinetic and thermodynamic studies showed that the adsorption proceeded via the pseudo-second-order kinetic model and endothermic in-nature for both dyes.     

Synthesis and characterization of phosphorylated Aspergillus niger for effective adsorption of uranium(VI)

The adsorption characteristics of phosphorylated Aspergillus niger (AN-P) for uranium(VI) were studied in this work. The AN-P was successfully prepared by the reaction of Aspergillus niger with phosphorus pentoxide in ice-bath under the catalysis of methanesulphonic acid. AN-P was characterized by FT-IR and SEM–EDS. The effects of pH, contact time, initial U(VI) ions concentration, adsorbent dosage and temperature on the adsorption of U(VI) by AN-P were investigated. The isotherm and kinetic data were accurately described by the Langmuir and pseudo-second-order models, respectively. The calculated thermodynamic parameters indicated that the adsorption of U(VI) by AN-P was an spontaneous and endothermic process. This indicated that the AN-P composite is a promising adsorbent for efficient removal of U(VI) from radioactive wastewater.

     

Thiol-functionalized Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> microspheres with superparamagnetism and their adsorption properties for Au(III) ion separation

Thiol-functionalized Fe₃O₄/SiO₂ microspheres (Fe₃O₄/SiO₂-SH) with high saturation magnetization (69.3 emu g^–1), superparamagnetism, and good dispersibility have been prepared by an ethylene glycol reduction method in combination with a modified Stöber method. The as-prepared composite magnetic spheres are characterized with fourier transform infrared spectroscopy (FT-IR), zeta potential, X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and superconducting quantum interference magnetometer, and tested in separation of Au(III) ions from aqueous solutions. The data for Au(III) adsorption on Fe₃O₄/SiO₂-SH are analyzed with the Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich isotherm models, and the pseudo-first-order, pseudo-second-order, and intraparticle diffusion kinetics models. The adsorption behaviors of Au(III) on Fe₃O₄/SiO₂-SH follow the Langmuir isotherm model, and the adsorption process conforms to the pseudo-second-order kinetic model. The maximum adsorption capacity of Au(III) on Fe₃O₄/SiO₂-SH is 43.7 mg g^–1. Acetate anions play an important role yet Cu(II) ions have little interference in the adsorption of Au(III) on the adsorbent. A satisfactory recovery percentage of 89.5% is acquired by using an eluent with 1 M thiourea and 5% HCl, although thiols have a high affinity to Au(III) ions based on the hard-soft acid-base (HSAB) theory by Pearson.     

Phenol removal from aqueous solution by carbon xerogel

Carbon xerogel (CX) was used for phenol adsorption from aqueous solution. CX was synthesized by sol?Cgel polycondensation of resorcinol with formaldehyde using sodium carbonate (Na₂CO₃) as catalyst. Then, it was dried by convective drying technique and pyrolyzed under inert atmosphere. Phenol adsorption kinetics was very fast, what was attributed to the presence of open pore structure. The kinetic studies showed that the adsorption process could be fitted to a pseudo-second-order model and the particle diffusion process is the rate-limiting step of the adsorption. The phenol removal was maximum and unaffected by pH changes when the initial pH of the phenol solution was in the range of 3?C8. The optimum adsorbent dose obtained for phenol adsorption onto CX was 0.075?g/50?cm³ solution. The Langmuir model described the adsorption process better than the Freundlich isotherm model and the monolayer adsorption capacity is 32?mg?g^?1. Among the desorbing solutions used in this study, the most efficient desorbent was EtOH (100?%) which released about 87?% of phenol bound with the CX.     

氧化锆-活性炭纤维复合材料的制备及其对F-吸附性能

采用水热合成法成功制备了氧化锆-活性炭纤维复合材料,并研究了其对F^-的吸附行为.表征结果表明,复合材料中氧化锆粒子成功负载于活性炭纤维上.吸附实验结果表明,负载了氧化锆的活性炭纤维对F^-有高效的去除效率,其吸附机理包括离子交换和静电作用力,吸附等温线符合Langmuir等温吸附模式,吸附动力学可用拟二级动力学模型拟合.吸附量随着溶液pH的升高而降低,共存离子Cl^-、NO₃^-和SO₄^2-对F^-在氧化锆-活性炭纤维复合材料上的吸附几乎没有影响.     

Assessment of adsorption properties of inorganic–organic hybrid cyclomatrix type polyphosphazene microspheres for the removal of Pb(II) ions from aqueous solutions

Abstract

Inorganic–organic hybrid cyclomatrix type polyphosphazene microspheres (poly[cyclotriphosphazene-co-(4,4′-diaminodiphenylmethane)]) (HDMS) and poly[cyclotetraphosphazene-co-4,4′-diaminodiphenylmethane)] (ODMS) were prepared to investigate their possible use as alternative adsorbents for the comparative study on Pb(II) ions removal from aqueous solutions. The structures of the microspheres were elucidated by Fourier Transform Infrared (FTIR) spectroscopy and Dynamic Light Scattering (DLS) measurements, and the surface morphologies were also observed by Scanning Electron Microscopy (SEM). The adsorption of Pb(II) ions onto HDMS and ODMS from aqueous solutions was examined by means of pH, temperature, contact time and concentration. Furthermore, adsorption kinetics and isotherm models were applied and the experimental data fitted well with Langmuir isotherm and pseudo-second-order kinetic models. The maximum adsorption capacities of HDMS and ODMS for Pb(II) ions were obtained as 157.8 and 308.0?mg g^?1 at 20?°C and pH 5.5, respectively.     

Adsorption of La(III) onto GMZ bentonite: effect of contact time,bentonite content,pH value and ionic strength

Bentonite has been studied extensively because of its strong adsorption capacity. A local Na-bentonite named GMZ bentonite, collected from Gaomiaozi County (Inner Mongolia, China), was selected as the first choice of buffer/backfill material for the high-level radioactive waste repository in China. In this research, the adsorption of La (ΙΙΙ) onto GMZ bentonite was performed as a function of contact time, pH, solid content and metal ion concentrations by using the batch experiments. The results indicate that the adsorption of La (III) on GMZ bentonite achieves equilibration quickly and the kinetic adsorption follows the pseudo-second-order model; the adsorption of La (III) on the adsorbent is strongly dependent on pH and solid content, the adsorption process follows Langmuir isotherm. The equilibrium batch experiment data demonstrate that GMZ bentonite is effective adsorbent for the removal of La (III) from aqueous solution with the maximum adsorption capacity of 26.8 mg g⁻¹ under the given experimental conditions.     

Magnetic porous polymer microspheres: Synthesis,characterization and adsorption performance for the removal of phenol

The magnetic poly(ethylene glycol dimethacrylate-n-vinylimidazole) (Fe₃O₄@poly (EGDMA@VIM)) microspheres were prepared by suspension polymerization method using magnetite Fe₃O₄ nano-powder and the porosity, morphology, chemical composition and structure of the magnetic polymer microspheres were characterized. The specific surface area and swelling ratio of the Fe₃O₄@poly(EGDMA@VIM) microspheres were found to be 278.6?m²·g^–1 and 48%, respectively. The Fe₃O₄@poly(EGDMA@VIM) microspheres were used as an adsorbent for phenol removal. The effects of the parameters such as adsorbent dosage, temperature, pH and initial concentration of phenol solutions on the adsorption were investigated. The experimental adsorption equilibrium data obtained were fitted with Langmuir, Freundlich and Dubinin-Radushkevich isotherms and the pseudo-first-order, pseudo-second-order and intra–particle diffusion kinetic models. The adsorption equilibrium data agreed well with the Freundlich isotherm and the pseudo-second-order kinetic model. The maximum capacity of the Fe₃O₄@poly(EGDMA@VIM) microspheres was calculated to be 33.83?mg·g^–1 at 298?K and natural pH from Langmuir isotherm. The Fe₃O₄@poly(EGDMA@VIM) microspheres were found to be reusable for removal of phenol after desorption for several times. The result indicated that the Fe₃O₄@poly(EGDMA@VIM) microspheres are potential candidate for removal of phenol in wastewaters.