Surface characteristics of high corrosion resistant Ni–Nb–Zr–Ti–Ta glassy alloys for nuclear fuel reprocessing applications

This work firstly discovered that the Ni₆₀Nb₁₅Zr₅Ti₁₅Ta₅ metallic glass exhibits high corrosion resistance in boiling 6 N HNO₃ solutions with and without Cr⁶⁺ ions, which may be of great potential for nuclear fuel reprocessing applications. The high corrosion resistance of the alloy is due to the formation of the passive film composed exclusively of Nb⁵⁺ and Ta⁵⁺ cations after immersion in the solution without Cr⁶⁺ ions, and Nb⁵⁺, Ta⁵⁺ and Cr³⁺ cations after immersion in the solution with Cr⁶⁺ ions.     

Study of ion adsorption at passive iron by using the impedance and photoadmittance methods

Intensity-modulated photocurrent (photoadmittance) and electrochemical impedance of anodicoxidized iron electrode in neutral nitrate solutions and in the presence of Ba²⁺, Ca²⁺, Cl^?, and C₆H₅COO^? (benzoate) are studied. It is shown that the ion adsorption at passive iron affects but slightly the system’s impedance; by contrast, it affects the photocurrent value significantly: when adsorbing, the anions increase the photoeffect, while the cations decrease it. These effects are associated with the potential drop redistribution in the Helmholtz layer and the film. The dissimilar changes of the generation current in the presence of similarly charged ions at their equal concentration evidence their different adsorption activity. The correlation between the generation current and surface-active ion concentration in solution is found. The photoelectrochemical spectroscopy allows evaluating qualitatively the surface-active ion adsorption at the passive iron and judging on the ion adsorption by the dependence of the generation current on the ion concentration.     

Characterization,EPR and photoluminescence studies of LiAl5O8:Cr phosphors

Red emitting Cr³⁺ doped LiAl₅O₈ powder phosphor was prepared by combustion route using corresponding metal nitrates and urea in a single step. The prepared powder was characterized by X-ray diffraction and surface area measurements were carried out by Brunauer–Emmet–Teller adsorption isotherms. The electron paramagnetic resonance spectrum in the low field regions is typical for isolated Cr³⁺ ions whereas the resonance signal in the high field region with g = 1.95 is due to exchange coupled Cr³⁺–Cr³⁺ pairs. The optical studies show two broad and intense bands characteristic of Cr³⁺ ions in distorted octahedral symmetry. The photoluminescence spectrum gives a narrow red emission at 710 nm corresponding to ²E_g → ⁴A_2g transition upon excitation of 562 nm. The crystal field parameter (Dq), Racah inter-electronic repulsion parameters (B and C) and nephelauxetic parameters have been evaluated and discussed.     

Simultaneous removal of Cu2+ and Cr3+ ions from aqueous solution based on Complexation with Eriochrome cyanine‐R and derivative spectrophotometric method

TiO₂ nanoparticles deposited on activated carbon (TiO₂–NP–AC) was prepared and characterized by XRD and SEM analysis. Subsequently, simultaneous ultrasound‐assisted adsorption of Cu²⁺ and Cr³⁺ ions onto TiO₂‐NPs‐AC after complexation via eriochrome cyanine R (ECR) has been investigated with UV–Vis and FAA spectrophotometer. Spectra overlapping of the ECR‐Cu and ECR‐Cr complex was resolve by derivative spectrophotometric technique. The effects of various parameters such as initial Cu²⁺ (A) and Cr³⁺ (B) ions concentrations, TiO₂‐NPs‐AC mass (C), sonication time (D) and pH (E) on the removal percentage were investigated and optimized by central composite design (CCD). The optimize conditions were set as: 4.21 min, 0.019 mg, 20.02 and 13.22 mg L^?1 and 6.63 for sonication time, TiO₂–NP–AC mass, initial Cr³⁺ and Cu²⁺ ions concentration and pH, respectively. The experimental equilibrium data fitting to Langmuir, Freundlich, Temkin and Dubinin–Radushkevich models show that the Langmuir model is a good and suitable model for evaluation and the actual behavior of adsorption process and maximum adsorption capacity of 105.26 and 93.46 mg g^?1 were obtained for Cu²⁺ and Cr³⁺ ions, respectively. Kinetic evaluation of experimental data showed that the adsorption processes followed well pseudo second order and intraparticle diffusion models.     

Synthesis and characterization of Cr-MSU-1 and its catalytic application for oxidation of styrene

Chromium-containing mesoporous silica material Cr-MSU-1 was synthesized using lauryl alcohol-polyoxyethylene (23) ether as templating agent under the neutral pH condition by two-step method. The sample was characterized by XRD, TEM, FT-IR, UV-Vis, ESR, ICP-AES and N₂ adsorption. Its catalytic performance for oxidation of styrene was studied. Effects of the solvent used, the styrene/H₂O₂ mole ratio and the reaction temperature and time on the oxidation of styrene over the Cr-MSU-1 catalyst were examined. The results indicate that Cr ions have been successfully incorporated into the framework of MSU-1 and the Cr-MSU-1 material has a uniform worm-like holes mesoporous structure. After Cr-MSU-1 is calcined, most of Cr³⁺ is oxidized to Cr⁵⁺ and Cr⁶⁺ in tetrahedral coordination and no extra-framework Cr₂O₃ is formed. The Cr-MSU-1 catalyst is highly active for the selective oxidation of styrene and the main reaction products over Cr-MSU-1 are benzaldehyde and phenylacetaldehyde. Its catalytic performance remains stable within five repeated runs and no leaching is noticed for this chromium-based catalyst.     

The effect of resin particle size on the rate of ion release: interactions in mixed bed systems

The aim of the present study is to evaluate the influence of resin particle sizes on the rate of ions release from a mixture of ion-exchange resins (named NMTD) which supplies calcium, fluoride, and phosphate ions as the main mineral content, and to elucidate the different phenomena taking place through the related ion-exchange process. The final goal of the study, related to dental application (enamel restoration), is to limit the particle size range, since the rate of ion release is a key parameter in the successful achievement of such objective. Weak-type ion-exchange resins, loaded with the appropriate ions, were ground and sieved into granulometric fractions of bead diameters of 0.1–0.075, 0.075–0.063, and 0.063–0.05 mm. Particle size was controlled by a laser diffraction particle distribution analyzer. The experiments on the kinetics of ions release were carried out under batch conditions in artificial saliva desorption solution thermostatized at 37 °C. The release of Ca²⁺ and F^– was determined by corresponding ion-selective electrodes automatically controlled, whereas H₂PO₄^– was measured spectrophotometrically by the inductively coupled plasma–optical emission technique (ICP-OES). The results of this study show that the process of ion-exchange for the different particle size fractions of resins is critical for the study of the kinetics release of the ions immobilized in the corresponding mixed bed polymeric matrices. In fact, despite the apparent narrow range of particle sizes of the mixed bed systems studied, appreciable differences in the rate of ions release are obtained. Since the ion release rate is depending on the contact surface, an increase of factor of 2 in particle size represents an increase of an order of magnitude of the resin contact surface due to the resin porosity. In this concern, it has been observed that the rate of ions release increases when particle size decreases. The interactions occurring during the ion release from the mixed bed resins (containing calcium-, fluoride-, and phosphate-loaded resins) can be interpreted by the following phenomena: H₂PO₄^–, which hardly modifies its rate of release in the presence of Ca²⁺ and F^– in the mixture, promotes a considerable increase in the rate of Ca²⁺ release due to the formation of a calcium dihydrogen phosphate soluble complex. F^– also produces an acceleration in the rate of Ca²⁺ release due to the formation of solid CaF₂ on the surface of cationic resin particles, which in contrast leads to a decrease in the rate of F^– release.     

Adsorption Properties of Hydrated Cr3+ Ions on Schiff‐base Covalent Organic Frameworks: A DFT Study

Considering the superior physiochemical property, increasing efforts have been devoted to exploiting the covalent organic frameworks (COFs) materials on the environmental remediation of heavy metal ions. Water pollution caused by Cr³⁺ metal ions is of special concern for scientists and engineers. Notwithstanding all the former efforts made, it is surprising that very little is known about the interaction mechanisms between the hydrated Cr³⁺ metal ions and COF materials. In present context, density functional theory (DFT) method is used to elucidate geometric and electronic properties with the purpose of putting into theoretical perspective the application values and interaction mechanisms for COF materials on Cr³⁺ capture. The results showed that all the five selected Schiff‐base COFs materials displayed good adsorption performance on Cr³⁺ removal while the phenazine‐linked and imine‐COFs possessed the most favorable adsorption capacity due to the optimal chemical units and frameworks. The hydration effect was found to play a two‐side role in the adsorption process and interaction mechanisms, involving coordination, hydrogen bonds, as well as weak non‐covalent interactions, have been illuminated to explain the observed different adsorption behaviors. This study provides a general guidance for the design and selection of efficient COF materials as high‐capacity Cr³⁺ adsorbents.     

Electrochemical behavior of CoCrMo implant in Ringer's solution

CoCrMo has been successfully employed as an orthopedic and orthodontic material because of its excellent corrosion resistant and suitable biocompatibility. The purpose of this research was to investigate the susceptibility of CoCrMo in Ringer's solution at three different temperatures: 22 °C, 37 °C, and 60 °C. The corrosion behavior of CoCrMo was carried out by using common electrochemical methods such as open circuit potential, potentiodynamic measurement, electrochemical impedance spectroscopy (EIS), and Mott–Schottky measurements. CoCrMo was passivated by the air, forming a passive film, which was not destroyed during the immersion in electrolytes under different temperatures. Results from potentiodynamic tests showed that at high anodic potentials, the passive film did not demonstrate significant localized corrosion and rather exhibited overall passive film degradation corresponding to the general corrosion of the alloy in Ringer's solution at the three temperatures. EIS measurements showed the presence of the stable passive film on the alloy surface when tested at open circuit potential. Mott–Schottky test indicated that the preformed passive film is an n‐type semiconductor due to the presence of a donor species. This is implied by the existence of oxygen vacancies and interstitial metallic cations. As the potential increased, the Cr³⁺ oxidized and produced soluble Cr⁴⁺ species. This resulted in the film changing to a p‐type semiconductor owing to the dissolution and creation of cation vacancies (acceptor species). The passive film rupture was not due to p‐type characteristics but rather was a result of the considerable oxidative dissolution of the film at high anodic potential. Copyright © 2013 John Wiley & Sons, Ltd.     

Biosorption of metal ions with Penicillium chrysogenum

Biosorption of metal ions with Penicillium chrysogenum mycelium is described in this article. Alkaline pretreatment was used to remove proteins and nucleic acids from cells, and this treatment increased the adsorption capacities, for Cr³⁺ from 18.6 mg g⁻¹ to 27.2 mg g⁻¹, for Ni²⁺ from 13.2 mg g⁻¹ to 19.2 mg g⁻¹, for Zn²⁺ from 6.8 mg g⁻¹ to 24.5 mg g⁻¹. The adsorption of metal ions was strongly pH dependent. The mycelium could beused for large-scale removal of Cr³⁺ from tannery wastewater. The results show that this inexpensive mycelium adsorbent has potential in industry because of its high adsorption capacity. The main chelating sites are amino groups (−NH₂) of chitosan in the mycelium. A new model is established, which describes the relation of adsorption of metal ions on pH according to amino group chelating with metal ions and H⁺. The relative errors of simulation for Cu²⁺, Ni²⁺, Zn²⁺, and Cr³⁺ are 4.66%, 5.45%, 11.55%, and 1.69%, respectively.     

Laser-induced luminescence of model Fe/Al2O3 and Cr/Al2O3 catalysts

The laser-induced luminescence of Cr³⁺ impurity ions in model Fe/Al₂O₃ and Cr/Al₂O₃ catalysts with different calcination temperatures was studied. It was found that an additional luminescence band at 770 nm appeared in the luminescence spectra of low-temperature samples as a result of the interaction of octahedrally coordinated Cr³⁺ ions with Fe³⁺ impurity ions. In the θ-Al₂O₃ phase with a concentration of Cr³⁺ ions higher than 0.1 wt %, the interaction of the Cr³⁺-Cr³⁺ ion pairs in the immediate surroundings resulted in the appearance of N _θ lines due to the splitting of R _θ lines. The differences of these lines from the N _α lines of α-Al₂O₃ were related to the individuality of the crystal lattice of the θ phase and the coordination of Cr³⁺ impurity ions in the immediate surroundings, which is different from that in the α phase. Based on the laser-induced luminescence spectroscopic data, it was found that regions with a local Cr³⁺ concentration higher than the average Cr³⁺ concentration in the bulk of a catalyst by one order of magnitude were formed in the α-Al₂O₃-Fe₂O₃ system with the bulk Fe and Cr concentrations of 2.5 and 0.04 wt %, respectively, which was calcined at 1220°C, as a result of the diffusion of chromium and iron ions.     

Magnetic properties of electrochemically prepared crystalline films of Prussian blue-based molecular magnets K j CrII k [CrIII(CN)6] l · mH2O

Crystalline films (thickness ～1 μm) of Prussian blue-based molecular magnets, synthesized using electrochemical method at two different reduction potentials ?0.5 and ?0.9 V, result into K_0.1Cr^II _1.45[Cr^III(CN)₆]?·?mH₂O (film 1) and K_0.8Cr^II _1.1[Cr^III(CN)₆]?·?mH₂O (film 2), respectively. The structural and magnetic properties of such films are investigated using atomic force microscopy (AFM), X-ray diffraction (XRD), infrared (IR) spectroscopy, and dc magnetization measurements. The film morphology, examined using AFM, shows uniformly distributed triangular crystallites over the substrate surface. The presence of Cr^III–C≡N–Cr^II sequence, in the range of 1,900 to 2,300 cm^?1 in IR spectra, confirms formation of Prussian blue analogues. The XRD results reveal information about the crystalline nature of the films and the relative intensities of the Bragg peaks change with the K⁺ ions. The exchange interaction between Cr ions through C≡N ligand confirms that the electron transfer from C≡N molecule to Cr ions is ferrimagnetic in nature. The high Curie temperatures (T _C) are found to be ～195 and ～215 K for film 1 and film 2, respectively. The higher value of T _C is attributed to the inclusion of more K⁺ ions for film 2, resulting decreases in the Cr^III(C≡N)₆ vacancies and increases in the number of nearest neighbors of Cr^II ions. The branching in the zero field-cooled and field-cooled magnetization data below Curie temperature is explained in terms of kinetic behavior of magnetic domains with different cooling conditions and the presence of water molecule vacancies in the lattice.     

A selective colorimetric and fluorescence chemosensing sensor for Cr<Superscript>3+</Superscript> based on a rhodamine base derivative

A rhodamine-conjugated coumarin (L) was used in designing a selective fluorescence chemosensor for the determination of trace amounts of Cr³⁺ ions in acetonitrile–water (MeCN/H₂O (90:10, %v/v) solutions. The intensity of the fluoresce emission of the chemosensor is intensified upon addition of Cr³⁺ ions in MeCN/H₂O (90:10, %v/v) solutions, due to the formation of a selective 1:1 complex between L and Cr³⁺ ions. The fluorescence enhancement versus Cr³⁺ concentration has been found to be linear from 1.0?×?10^?7 to 1.8?×?10^?5 M and a detection limit of 7.5?×?10^?8 M. The proposed fluorescent probe proved to be highly selective towards Cr³⁺ ions as compared to other common metal ions and could be successfully applied to the determination of Cr³⁺ concentrations in some water and wastewater samples.     

Incongruent dissolution of hydroxyapatite in the presence of phosphoserine

Concentrations of phosphate and calcium ions, liberated from the surface of hydroxyapatite (HAP) during the adsorption of phosphoserine (PSer), were determined at 30°C. HAP showed a marked incongruent dissolution behavior in the presence of PSer. That is, the concentration of phosphate ion in solution increases with the addition of PSer due to the ion-exchange between PSer and phosphate ion on HAP (molar ratio of the former to the latter=32), whereas the concentration of calcium ion decreases with this release of phosphate ion, because the solubility product of HAP restricts the concentrations of both ions in solution (calculated values of — log (Ca²⁺)¹⁰ (PO ₄ ^3– )⁶ (OH^–)² were 115.8±1.0). The affinity of PSer to HAP was highest at pH 5.8 where the PSer and the HAP surface had the opposite charges. This electrostatic attraction force between PSer and HAP was shielded to some extent by the addition of KCl.     

Electronic state and local surrounding of <Superscript>119</Superscript>Sn in calcium-substituted holmium orthochromites

The influence of Ca²⁺ doped into the holmium sublattice on the magnetically active surrounding of Sn⁴⁺ ions located in the chromium sublattice of Ho_1–x Ca _x Cr_0.997Sn_0.003O₃ (x = 0, 0.003, and 0.1) compounds was studied by ¹¹⁹Sn Mössbauer spectroscopy. At concentrations [Ca] = [Sn] = 0.3 mol %, an increase was observed in the spectral contribution of Sn⁴⁺ sites, having the full number of nearest-neighbor Cr³⁺cations (n = 6), where they perceived a magnetic field H(Sn)_{4.2 K} = 82 kOe, compared to the contribution of the relevant sites in the undoped chromite (x = 0). This observation was interpreted as resulting from a reduced probability of appearance of Cr³⁺ vacancies in the nearest surrounding of heterovalent Sn⁴⁺ ions. For x = 0.1, on the contrary, the ¹¹⁹Sn spectrum revealed a reduced contribution from the Sn⁴⁺ sites with n = 6. This evolution is shown not to be due neither to the appearance of Cr⁴⁺ nor Cr⁶⁺ ions in the nearest neighborhood of Sn⁴⁺ in the chromium sublattice to balance the charge deficiency of the Ca²⁺ ions doped into the holmium sublattice. This allowed us to suggest that the observed effect was due to the onset of Sn⁴⁺ segregations in the structure of Ho_0.9Ca_0.1Cr_0.997Sn_0.003O₃, which contained a far greater amount of Ca²⁺ ions whose charge deficiency was balanced mostly by Cr⁴⁺ formation. Studies of samples that were prepared under a hydrogen atmosphere revealed the reduction of Sn⁴⁺ to the oxidation state +2, with the concomitant stabilization of the formed Sn²⁺ ions on crystallite surfaces on sites having low coordination numbers.     

Synthesis and Characterization of Nanostructured Fe3O4 Micron‐Spheres and Their Application in Removing Toxic Cr Ions from Polluted Water

We present a simple and effective method for the synthesis of nanostructured Fe₃O₄ micron‐spheres (NFMSs) by annealing hydrothermally formed FeCO₃ spheres in argon. The phase structure, particle size, and magnetic properties of the product have been characterized by X‐ray diffraction (XRD), Fourier‐transform infrared spectroscopy (FTIR), X‐ray photoelectron spectroscopy (XPS), field‐emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and by means of a superconducting quantum interference device (SQUID). The results have shown that the as‐obtained NFMSs have a diameter of about 5 μm and are composed of nanometer‐sized porous lamellae. The NFMSs have a large specific surface area (135.9 m² g^?1), reductive Fe²⁺ incorporated into their structure, and intense magnetic properties. These properties suggest that NFMSs have potential application in removing toxic Cr⁶⁺ ions from polluted water. At 25 °C, each gram of NFMSs product can remove 43.48 mg of Cr⁶⁺ ions, as compared to just 10.2 mg for nanometer‐sized Fe₃O₄ and 1.89 mg for micron‐sized Fe₃O₄. The enhanced removal performance can be ascribed to the structural features. Moreover, the Cr⁶⁺ ion removal capacity of the NFMSs can reach up to 71.2 mg g^?1 at 50 °C. The influencing parameters in the removal of Cr⁶⁺ ions, such as contact time, pH, and temperature, have been evaluated. The Cr⁶⁺‐removal mechanism has been investigated. We have found that the NFMSs product not only serves as an effective adsorbent to remove toxic Cr⁶⁺ ions from polluted water, but also as an effective reductant in reducing the adsorbed toxic Cr⁶⁺ ions to much less toxic Cr³⁺ through the Fe²⁺ incorporated into its structure.     

A novel spinel coating on cobalt‐based Superalloy GH605 via an in‐situ oxidation approach

Cr‐Mn‐O spinel coating was prepared on the surface of cobalt‐based superalloy GH605 via an in‐situ oxidation method in H₂O‐H₂ environment. The composition, morphology, and chemical value state of the oxide spinel coatings were investigated by SEM, EDS, XRD, Raman spectra, and XPS. It indicated that the morphology of coating varied with oxidation temperature, and granular surface appeared when oxidation temperature increased to 1100°C. The formed Cr‐Mn‐O spinel coating was composed of Cr₂O₃ and MnCr₂O₄, and the thickness increased significantly with oxidation temperature. In the coating, Cr element existed in the state of Cr³⁺ ions and Cr⁶⁺ ions, while Mn element only existed in the form of Mn²⁺ ions.     

Metal adsorption properties of multi-functional PAMAM dendrimer based gels

Metal adsorption studies are getting important and there are many functional adsorbents developed recently. Here, we report the synthesis of multifunctional PAMAM G2 (polyamidoamine) possessing methacryl, amine, hydroxyl and phosphonate groups used in free radical curing gel formulations. UV curable gel is conducted in the presence of acrylamide, bisacrylamide, and polyethylene glycol diacrylate. Adsorption study of the resulting novel sorbents (gels) are carried out with a series of metals. Through a comprehensive study, structure–property relationship of the series gels is conducted by using different amount of amine, hydroxyl, and/or phosphonate ester groups on the PAMAM G2. Selected metals are Cr³⁺, Fe³⁺, Ni²⁺, Cu²⁺, Ag⁺, and Cd²⁺ within a series of hard, intermediate, and soft ionic species. Adsorption study is carried out in pure water environment at neutral pH. Metal ions removal percentages and adsorption capacities of gel adsorbents are calculated by using atomic absorption spectroscopy. There is relationship between the overall functional groups presence in gel formulation and swelling densities for removing the metal ions. Introducing dendrimer into the gel formulation enhanced the metal ions adsorption against to Bare GEL formulation which do not possess dendrimer units. Consequently, the maximum removal efficiency has been obtained for Cr³⁺ and Fe³⁺.     

Indirect radiotracer study of the adsorption of chromate ions on γ-Al2O3 and direct study of the adsorption of sulfate ions on Cr2O3 using 35S-labelled H2SO4

The specific adsorption of sulfate ions on Cr₂O₃ was studied by a radiotracer technique using ³⁵S-labelled sulfuric acid in low concentrations (c<10^–3 mol dm^–3) in the presence of a large excess of perchlorate supporting electrolyte. The pH and concentration dependence were determined. It was found that the extent of adsorption is determined by the protonation of the surface sites, similar to other oxides studied previously. A comparison of Cr₂O₃ and Al₂O₃ in this respect shows that the protonation of the former takes place at significantly lower pH values than that of the latter. The indirect radiotracer study of the adsorption of chromate on Al₂O₃ was carried out using labelled sulfate ions as indicator species. The results obtained show that the adsorption strength of chromate species is very low in comparison to sulfate ions and a regular Langmuir-like adsorption behaviour can be observed. It is believed that the observations presented may contribute to a better understanding of the behaviour of surface layers with a mixed oxide content. Electronic Publication     

Determination of pH value of isoelectric solution and identification of passive iron surface phases using immersion method

Using the method of phase modeling, the pH values of solutions corresponding to the uncharged surface of passive iron and ferric oxide γ-Fe₂O₃ (pH₀) are compared. According to the theory of connected places, the charge of metal oxide surface is determined by the adsorption or desorption of hydrogen ions leading to a change in the potential drop at the oxide/solution interface. Preliminarily passivated iron electrode was washed with twice-distilled water and placed into 0.5 M NaNO₃ solution with various pH values; the variation in the potential (ΔE) with time was studied. The pH₀ value for passive electrode under the open-circuit conditions was determined by the dependence of ΔE on the pH value (pH₀ 6.2 ± 0.1). The pH₀ value was close to that for γ-Fe₂O₃ (pH₀ 6.2), which was determined by the method of potentiometrical titration of oxide suspension in the nitrate solution. The introduction of surface-active ions Ba²⁺ and Cl^? changes the charge of passive iron surface: Ba²⁺ ions increase the electrode potential, while Cl^? ions decrease it. Comparing the pH₀ values for passive electrode and metal oxides, one can identify the composition of passive electrode surface.