Evaluation of network parameters and drug release behavior of gum acacia-crosslinked-carbopol hydrogel wound dressings

Present article discusses the synthesis, characterization, biodegradation, network parameter and drug release of gum acacia-crosslinked-carbopol hydrogel wound dressing. Polymers have been characterized by ¹³C solid state nuclear magnetic resonance spectroscopy, elemental analysis, cryo-scanning electron microscopy, atomic force microscopy, thermogravimetric analysis, differential thermal analysis, differential thermogravimetry, and differential scanning calorimetry studies. Network parameters of hydrogel wound dressings such as polymer volume fraction in the swollen state φ, Flory–Huggins interaction parameter χ, molecular weight of the polymer chain between two neighboring cross links M_c, crosslink density ρ and the corresponding mesh size ξ have also been determined. Different in vitro release kinetic models (zero order, first order, Higuchi square root law, Korsmeyer-Peppas, and Hixson-Crowell cube root models) have been applied on the drug release profile. The release of antibiotic drug moxifloxacin from the drug loaded hydrogel matrix occurred through non-Fickian diffusion mechanism and release profile best fitted in the Korsmeyer-Peppas model. Semi-contact mode atomic force microscopic imaging showed that rough surface with root mean square roughness 82.868 nm of the polymer films.     

Dynamic Release of Riboflavin from Ethyl Cellulose Coated Barium Alginate Beads for Gastrointestinal Drug Delivery: An in vitro Study

The present work describes the dynamic release of model drug riboflavin form uncoated and ethyl cellulose coated barium alginate beads in the media of continuous varying pH at the physiological temperature 37°C. The drug release behavior has been studied in the simulating gastric fluid (SGF, pH 1.2) for 0–2 h and then in the simulating intestinal fluid (SIF pH 6.8) for 2–48 h. In addition to the traditional dissolution test (TDT, the dynamic release has also been studied by a newly developed method, called ‘flow through diffusion cell’ (FTDC). The release profiles, obtained by using these two methods have been found to differ appreciably from each other. Moreover, the nature of the solid mass surrounding the beads in the FTDC method also influences the release behavior of beads. The uncoated beads demonstrated faster drug release of drug in the medium of lower pH (i.e., 1.2) as compared to that in the medium of pH 6.8 and the release process was found to be diffusion controlled.     

A pH‐sensitive water‐soluble N‐carboxyethyl chitosan/poly(hydroxyethyl methacrylate) hydrogel as a potential drug sustained release matrix prepared by photopolymerization technique

Biocompatible pH‐sensitive semi‐interpenetration polymeric network hydrogels (semi‐IPN) based on water‐soluble N‐carboxyethyl chitosan (CECS) and 2‐hydroxyethyl methacrylate (HEMA) were synthesized by the photopolymerization technique. pH‐sensitivity, cytotoxicity, morphology, mechanical property, and water state of hydrogel were investigated by a swelling test, methylthiazolydiphenyl‐tetrazolium bromide (MTT) assay, scanning electron microscopy (SEM), universal testing machine, and differential scanning calorimetry (DSC), respectively. The drug release studies were carried out using 5‐Flurouracil as the model drug. The results indicated that the hydrogels were sensitive to pH of the medium and its wet state had good mechanical properties. The results of cytotoxicity and prolonged drug release characteristics revealed the suitability of the hydrogels as drug delivery matrices. The release kinetics was evaluated by fitting the experimental data to standard release equations, and the best fit was obtained with the Higuchi model of the hydrogel. Copyright © 2008 John Wiley & Sons, Ltd.     

Methyl methacrylate-co-itaconic acid (MMA-co-IA) hydrogels for controlled drug delivery

In the present work methyl methacrylate-co-itaconic acid (MMA-co-IA) hydrogels were synthesized by free radical copolymerization of methyl methacrylate (MMA) and itaconic acid (IA) using ethylene glycol dimethacrylate (EGDMA) and methylene bisacrylamide (MBAAm) as crosslinkers and benzoyl peroxide as initiator. Selected samples were loaded with model drug lactulose. For the lactulose release, the effect of pH, monomeric compositions, degree of crosslinking were investigated. The release of lactulose was studied for 8 h period in USP phosphate buffer solutions of varying pH 1.2, 5.5, 6.5 and 7.0. The drug release data were fitted into various kinetics models like the zero order, first order, Higuchi and Peppas. The release kinetics of lactulose from MMA/IA hydrogels was found to be best described by the Peppas model. Results showed that drug release increased by increasing IA content in the hydrogels but the effect of changing of crosslinking ratio on drug release was not significant. The surface morphology of MMA/IA drug loaded hydrogel was studied by SEM which revealed uniform distribution of the drug in the hydrogels. In conclusion, it can be said that lactulose can be successfully incorporated into crosslinked MMA/IA hydrogels and its release can be modulated by changing the mole fraction of the acid component in the gels.     

Flow Through Diffusion Cell Method: A Better Approach to Study Drug Release Behavior as Compared to Traditional Dissolution Test Method

Co‐polymeric hydrogels consisting of N‐vinyl‐2‐pyrrolidone (NVP) and acrylic acid (AAc) were synthesized and evaluated for release of a model drug, i.e., vitamin B₁₂. Release studies in simulated gastric fluid (pH 1.2) and intestinal fluid (pH 7.4), at 37°C, showed the hydrogels to be pH sensitive. An in vitro release study by ‘traditional dissolution test’ (TDT) showed that percent drug released from the hydrogel was nearly 8.6±2.1 and 83.2±4.8 in the media of pH 1.2 and 6.8, respectively. However, in order to incorporate in vivo GI conditions such as acidic pH and high water content in the stomach, low water content and the presence of a semi–solid mass in the large intestine, a new test model, called flow through diffusion cell (FTDC) was also used. The two approaches yielded almost different release profiles. The gels were characterized by thermogravimetric analysis and FTIR spectroscopy.     

Synthesis, characterization and sustaining controlled release effect of mesoporous SBA-15/ramipril composite drug

A loading of ramipril in SBA-15 (Santa Barbara Amorphous) mesoporous material was studied. (SBA-15)-ramipril composite material was characterized by chemical analysis, infrared spectroscopy, powder X-ray diffraction, low temperature N₂ adsorption–desorption at 77 K characterization techniques. Ramipril drug release processes from SBA-15 host to simulated body fluid (SBF), simulated gastric juice (SGJ), simulated intestinal fluid (SIF) were monitored in a simulated way and actions of the sustained release of (SBA-15)-ramipril was studied. The results showed that the loading amount of ramipril drug in SBA-15 was 90.30 mg/g. The cumulative sustained release rate of ramipril composite drug in SBF achieved 99.7 % after 27 h. When the sustained release of composite drug in SGJ was 8 h, the maximum cumulative sustained release ratio achieved 54.9 %. When the sustained release of composite drug was 9 h in SIF, the maximum cumulative sustained release ratio achieved 34.9 %. The method described in this study is suitable for carrying ramipril drug on SBA-15, and a new carrier to load ramipril drug was found. Meanwhile, the efficacy of ramipril drug and time efficacy could be improved.     

Modification of WS2 nanosheets with beta-cyclodextrone and N-isopropylacrylamide polymers for tamoxifen adsorption and investigation of in vitro drug release

In this research, tungsten disulfide (WS₂) nanosheets were modified with beta-cyclodextrone (βCD) N-isopropylacrylamide polymers (NIPAAP) for adsorption of tamoxifen (TAM) drug. The synthesized WS₂/βCD/NIPAAP samples were characterized by field-emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and X-ray diffraction (XRD) analyses. The adsorption experiments of TAM on WS₂/βCD/NIPAAP were performed as a function of pH, reaction contact time, temperature and drug concentration. The adsorption kinetic data were well fitted to the pseudo-second-order model. Also, the equilibrium data were well described by Langmuir isotherm model. The maximum adsorption capacity of WS₂/βCD/NIPAAP for TAM drug was found to be 62.0 mg/g. The results of regeneration tests showed that the synthesized WS₂/βCD/NIPAAP adsorbent can be easily reused after 6 cycles of adsorption–desorption. Furthermore, TAM drug release was investigated in a simulated system with pH 7.4 at different temperatures. The results showed that the release of TAM drug from WS₂/βCD/NIPAAP carrier at 50 °C and 37 °C was greater than TAM release at 25 °C. Also, the experimental data of drug release were studied by Higuchi, Ritger-Peppas, zero-order and first-order models. The release data were well fitted to the zero-order model indicating a case II transport. The results showed a high stability for TAM drug.

     

Budesonide-Loaded Pectin/Polyacrylamide Hydrogel for Sustained Delivery: Fabrication,Characterization and In Vitro Release Kinetics

A single ulcerative colitis (UC) is a chronic inflammatory bowel disease (IBD) that causes inflammation of the colonic mucosa at the distal colon and rectum. The mainstay therapy involves anti-inflammatory immunosuppression based on the disease location and severity. The disadvantages of using systemic corticosteroids for UC treatment is the amplified risk of malignancies and infections. Therefore, topical treatments are safer as they have fewer systemic side effects due to less systemic exposure. In this context, pH sensitive and enzymatically triggered hydrogel of pectin (PC) and polyacrylamide (PAM) has been developed to facilitate colon-targeted delivery of budesonide (BUD) for the treatment of UC. The hydrogels were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), swelling ratio, and drug release. FT-IR spectroscopy confirmed the grafting as well loading of BUD in hydrogel. XRD showed the amorphous nature of hydrogel and increment in crystallinity after drug loading. On the other hand, SEM showed that the hydrogels exhibited a highly porous morphology, which is suitable for drug loading and also demonstrated a pH-responsive swelling behaviour, with decreased swelling in acidic media. The in-vitro release of BUD from the hydrogel exhibited a sustained release behaviour with non-ficken diffusion mechanism. The model that fitted best for BUD released was the Higuchi kinetic model. It was concluded that enzyme/pH dual-sensitive hydrogels are an effective colon-targeted delivery system for UC.     

Temperature and pH-Sensitive Polymers with Hydrophobic Spacers for the Controlled Delivery of Drugs

Summary: Acid methacrylates containing hydrophobic aliphatic and aromatic spacers were used to prepare pH-sensitive ampholytic hydrogels and bidimensional temperature- (T) and pH-sensitive hydrogels. Their swelling behaviour was studied by changing the pH and temperature of buffer solutions. Salicylamide, salicylic acid and green fluorescent protein (GFP) as model drugs were loaded into the gels and their release kinetics studied under simulated gastric and intestinal conditions. T- and pH-sensitive hydrogels containing aliphatic spacers show sustained release of analgesics depending on pH (e.g. 7.4); while longer aliphatic spacers resulted in drug release depending on pH and temperature (T < transition T). GFP was released from temperature- and pH-sensitive ampholytic hydrogels after different lag times depending on hydrogel composition.     

Thermoresponsive N-vinyl caprolactam grafted sodium alginate hydrogel beads for the controlled release of an anticancer drug

A series of thermoresponsive sodium alginate-g-poly(vinyl caprolactam) (NaAlg-g-PNVCL) beads were prepared as drug delivery matrices of 5-flurouracil (5-FU) crosslinked by glutaraldehyde (GA) in the hydrochloric acid catalyst. Graft copolymers of sodium alginate with vinyl caprolactam were synthesized using azobisisobutyronitrile as an initiator, and characterized by Fourier infrared spectroscopy, differential scanning calrimetry and X-ray diffraction for analysis of the amorphous nature drug in the beads, and by scanning electron microscopy for the spherical nature of the beads. Preparation condition of the beads was optimized by considering the percentage of encapsulation efficiency, swelling behavior of beads and their release data. Effects of variables such as GA concentration, drug/polymer ratio and catalyst concentration on the release of 5-FU were carried out at two different temperatures (25 and 37 °C) in simulated intestinal fluid for 12 h. It was observed that, drug release from the beads decreased with increasing drug/polymer (d/p) ratio, extent of crosslinking agent and catalyst concentration. The swelling degree of graft copolymer beads was found to be increased with decreasing of environmental temperature. In vitro release studies were performed at 25 and 37 °C for 12 h, and showed that thermoresponsive graft copolymer beads had higher drug release behavior at 25 °C than that at 37 °C, following Fickian diffusion transport mechanism with slight deviation.     

Acyclovir-Loaded Chitosan Microspheres for Gastroretention: Development and Evaluation

Mucoadhesive chitosan microspheres of acyclovir were prepared to prolong the gastric residence time using simple emulsification phase separation technique. The particle morphology of drug-loaded formulations was measured by SEM and the particle size distribution was determined using an optical microscope. The release profile of acyclovir from microspheres was examined in simulated gastric fluid (SGF pH 1.2). The particles were found to be discreet and spherical with the maximum particles of an average size (31.62 ± 4.64). The entrapment efficiency was found to be in the range of 40.24 to 67.29%. The concentration of the glutaraldehyde (25%v/v) as a cross-linker 2 ml and drug polymer ratio of 1:2 caused an increase in the entrapment efficiency and the extent of drug release. The optimized chitosan microspheres were found to possess good bioadhesion (79.89 ± 1.01%). The gamma-scintigraphy study showed the gastric residence time of more than 6 hours which revealed that optimized formulation could be a good choice for gastroretentive systems.     

麦饭石含量对载药复合凝胶小球释药性能的影响

以瓜尔胶-g-聚丙烯酸/麦饭石复合水凝胶(GG-g-PAA/MS)和海藻酸钠(SA)为原料,双氯芬酸钠(DS)为模拟药物,采用离子凝胶法制备了载药复合凝胶小球,考察了pH敏感性以及MS含量对复合凝胶小球的包封率、载药率、溶胀性和药物释放行为的影响.结果表明:凝胶小球具有明显的pH敏感性,在不同pH介质中溶胀率和释放速率...     

Characterization and in vitro release kinetics of chitosan based biocomposites from Scotch Bonnets

The main aim of this study is to formulate the combination of the bioactive composite containing chitosan/β -tricalcium phosphate (CH/β-TCP) as potential drug delivery platforms for the sustained release of antibiotics. Herein the mode of amoxicillin (AMX) maintained in the β-TCP/chitosan composite was characterized using XRD, FT-IR to confirm the phase purity and functional groups. SEM was used to examine the size and shape of particles. The SEM images of the biocomposites after drug release confirmed that they are biodegradable. In vitro drug release experiments in PBS (pH 7.4) revealed a sustained release profile in a neutral medium. Drug release profiles were evaluated according to five different kinetic models including Zero Order, First Order, Higuchi, Hixon Crowel, and Korsmeyer-Peppas. The release profile was best expressed by the Korsmeyer Peppas model because the results showed high linearity. Overall, the positive effect of chitosan coating on the drug elution profile of β-TCP as carriers for the controlled delivery of antibiotics was regarded as biocompatible for the controlled drug delivery system.     

Synthesis and Evaluation of Biocompatible pH‐Sensitive Hydrogels as Colon‐Specific Drug Delivery Systems

Because of the growing importance of pH‐sensitive hydrogels as drug delivery systems, biocompatible copolymeric hydrogels based N‐vinyl‐2‐pyrrolidinone (NVP) and methacrylic acid (MAA) were designed and synthesized. These hydrogels were investigated for oral drug delivery. Radical copolymerizations of N‐vinyl‐2‐pyrrolidinone (NVP) and methacrylic acid (MAA) with the various ratios of cross‐linking agent were carried out at 70 °C. Azabisisobutyronitrile (AIBN) was the free‐radical initiator employed and Cubane‐1,4‐dicarboxylic acid (CDA) linked to two 2‐hydroxyethyl methacrylate (HEMA) group was the crosslinking agent (CA) used for hydrogel preparations. The hydrogels were characterized by differential scanning calorimetry and FT‐IR. Equilibrium swelling studies were carried out in enzyme‐free simulated gastric and intestinal fluids (SGF and SIF, respectively). A model drug, olsalazine [3,3′‐azobis (6‐hydroxy benzoic acid)] (OSZ) as an azo derivative of 5‐aminosalicylic acid (5‐ASA), was entrapped in these gels and the in‐vitro release profiles were established separately in both enzyme‐free SGF and SIF. The drug‐release profiles indicated that the amount of drug released depended on the degree of swelling. The swelling was modulated by the amount of crosslinking of the polymer bonded drug (PBDs) prepared. Based on the great difference in hydrolysis rates at pH 1 and 7.4, these pH‐sensitive hydrogels appear to be good candidates for colon‐specific drug delivery.     

Formulation of pH-sensitive aminated chitosan–gelatin crosslinked hydrogel for oral drug delivery

The objective of this study is to develop efficient pH-sensitive hydrogel based on aminated chitosan (AmCs) and gelatin (Gel) biopolymers for oral drug delivery. Herein, AmCs was chemically crosslinked with gelatin (Gel) biopolymer with different ratios, while their structures, thermal profiles and morphological properties were investigated by FTIR, TGA and SEM characterization tools, respectively. Moreover, gel-content, crosslinking density and rheological analysis were also performed. The results clarified that the developed AmCs-Gel crosslinked hydrogel displayed variable pH-sensitive swelling profiles. By increasing AmCs ratio, the swelling ratio was boosted at pH 1.2 and declined at pH 7.4. Besides, by increasing gelatin ratio in the hydrogel matrix, the loading efficiency of Oseltamivir phosphate (as a model of drug) was augmented and reached maximum value of 79.0% by AmCs-Gel (2:3) crosslinked hydrogel. The in vitro drug release profiles were investigated for 6 h in simulated gastric fluid [SGF; pH 1.2] and simulated colon fluid [SCF; pH 7.4]. Variable release profiles were realized depending on variation of AmCs and Gel ratios in the crosslinked hydrogel matrix. Finally, the formulated smart crosslinked AmCs-Gel hydrogels demonstrated acceptable biodegradability with no cellular toxicity, suggesting their applicability as pH-sensitive oral drug carriers.     

Design of polyvinyl alcohol hydrogel as a controlled-release vehicle for rectal administration of dl-propranolol-HCl and atenolol

Preparations of beta-blockers, propranolol-HCl and atenolol, in poly(vinyl alcohol) (PVA) hydrogel were designed for the therapeutic treatment of hypertension by transrectal delivery. In vitro release characteristics and plasma drug concentration profiles after rectal administration in rats and dogs were examined. The PVA hydrogels containing beta-blockers were prepared by a low-temperature crystallization method. The release of beta-blockers from hydrogel preparations was consistent with Fickian diffusion (Higuchi model); the drug release versus the square root of release time profile gave a straight line over 60% of the total release process. The release of beta-blockers from hydrogel preparations increased at higher concentrations of PVA in the hydrogel preparations and was not affected by the pH of hydrogel preparations. Plasma concentrations of beta-blockers after rectal administration of hydrogels were higher than those after administration of suppositories (Witepsol H-15) in rats and dogs. The drug plasma concentrations increased at higher concentrations of PVA in hydrogel preparations. In the case of propranolol, which is a hepatic high-clearance drug, area under the blood concentration curve, 0-8 h after rectal administration of a hydrogel preparation (20% w/w PVA, pH 7.0) was 2.16 times and 5.26 times higher than those obtained with Witepsol H-15 suppository and oral administration, respectively. Rectal administration with PVA hydrogels is a favorable route for a hepatic high-clearance drug such as propranolol.     

Dual crosslinked pH‐ and temperature‐sensitive hydrogel beads for intestine‐targeted controlled release

Novel drug‐loaded hydrogel beads for intestine‐targeted controlled release were developed by using pH‐ and temperature‐sensitive carboxymethyl chitosan‐graft‐poly(N,N‐diethylacrylamide) (CMCTS‐g‐PDEA) hydrogel as carriers and vitamin B₂ (VB₂) as a model drug. The hydrogel beads were prepared based on Ca²⁺ ionic crosslinking in acidic solution and formed dual crosslinked network structure. The structure of hydrogel and morphology of drug‐loaded beads were characterized by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). The study about swelling characteristics of hydrogel beads indicated that the beads had obvious pH‐ and temperature‐sensitivity. In vitro release studies of drug‐loaded beads were carried out in pH 1.2 HCl buffer solution and pH 7.4 phosphate buffer solution at 37°C, respectively. The results indicated that the dual crosslinked method could effectively control the drug release rate under gastrointestinal tract (GIT) conditions, which was superior to traditional single crosslinked beads. In addition, the effects of grafting percentage, pH value, and temperature on the release behavior of the VB₂ were investigated. The drug release mechanism of CMCTS‐g‐PDEA drug‐loaded beads was analyzed by Peppa's potential equation. According to this study, the dual crosslinked hydrogel beads based on CMCTS‐g‐PDEA could serve as suitable candidate for drug site‐specific carrier in intestine. Copyright © 2009 John Wiley & Sons, Ltd.     

pH-sensitive polyelectrolyte complex gel microspheres composed of chitosan/sodium tripolyphosphate/dextran sulfate: swelling kinetics and drug delivery properties

Porous chitosan (CS) polyelectrolyte complex (PEC) hydrogel microspheres were prepared via either wet phase-inversion or ionotropic crosslinking with sodium tripolyphosphate (Na+ - TPP) and dextran sulfate (DS). The resulting microspheres were characterized using scanning electron microscopy (SEM) and elemental analysis (EA). The controlled release behavior of ibuprofen (IBU) from these microspheres was investigated. The PEC microspheres were about 700-950 microm in diameter with large pores and open porous structure. The CS/TPP/DS microspheres resisted hydrolysis in strong acid and biodegradation in enzymatic surroundings. The swelling kinetics for CS microspheres was close to Fickian diffusion, whereas those for CS/TPP and CS/TPP/DS were non-Fickian. Furthermore, the equilibrium water content (EWC) and water diffusion coefficient (D) increased with the pH of the media. The release profiles of IBU from CS/TPP/DS microspheres were slow in simulated gastric fluid (SGF, pH 1.4) over 3 h, but nearly all of the initial drug content was released in simulated intestinal fluid (SIF, pH 6.8) within 6 h after changing media. Overall the results demonstrated that CS/TPP/DS microspheres could successfully deliver a hydrophobic drug to the intestine without losing the drug in the stomach, and hence could be potential candidates as an orally administered drug delivery system.     

魔芋葡甘聚糖/聚乙烯醇纳米纤维膜及其释药行为研究

为了研制药物缓释效果优良的薄膜材料,利用静电纺丝设备研制不同比重的魔芋葡甘露聚糖/聚乙烯醇纳米纤维膜,并通过扫描电镜、傅里叶变换红外光谱和示差扫描量热法表征纳米纤维膜的结构和性能,结合体外实验和数学模型研究其缓释行为.结果显示当魔芋葡甘露聚糖含量占纳米纤维膜总质量约76%时,纳米纤维膜中微纤丝粗细最均匀且结点较少,纳米纤维膜中魔芋葡甘聚糖和聚乙烯醇之间存在明显的相互作用,含有5-氨基水杨酸的纳米纤维膜在pH=7.4 PBS磷酸盐缓冲液中25 h的累积释放量大约为45%,显示出良好的药物缓释效果,其缓释行为与Higuchi模型具有较高的拟合度.研究表明利用静电纺丝设备研制的魔芋葡甘聚糖/聚乙烯醇纳米纤维膜可以为药物缓释载体的开发提供理论依据.     

Development of Antibacterial,Degradable and pH-Responsive Chitosan/Guar Gum/Polyvinyl Alcohol Blended Hydrogels for Wound Dressing

The present research is based on the fabrication preparation of CS/PVA/GG blended hydrogel with nontoxic tetra orthosilicate (TEOS) for sustained paracetamol release. Different TEOS percentages were used because of their nontoxic behavior to study newly designed hydrogels’ crosslinking and physicochemical properties. These hydrogels were characterized using Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and wetting to determine the functional, surface morphology, hydrophilic, or hydrophobic properties. The swelling analysis in different media, degradation in PBS, and drug release kinetics were conducted to observe their response against corresponding media. The FTIR analysis confirmed the components added and crosslinking between them, and surface morphology confirmed different surface and wetting behavior due to different crosslinking. In various solvents, including water, buffer, and electrolyte solutions, the swelling behaviour of hydrogel was investigated and observed that TEOS amount caused less hydrogel swelling. In acidic pH, hydrogels swell the most, while they swell the least at pH 7 or higher. These hydrogels are pH-sensitive and appropriate for controlled drug release. These hydrogels demonstrated that, as the ionic concentration was increased, swelling decreased due to decreased osmotic pressure in various electrolyte solutions. The antimicrobial analysis revealed that these hydrogels are highly antibacterial against Gram-positive (Staphylococcus aureus and Bacillus cereus) and Gram negative (Pseudomonas aeruginosa and Escherichia coli) bacterial strains. The drug release mechanism was 98% in phosphate buffer saline (PBS) media at pH 7.4 in 140 min. To analyze drug release behaviour, the drug release kinetics was assessed against different mathematical models (such as zero and first order, Higuchi, Baker–Lonsdale, Hixson, and Peppas). It was found that hydrogel (CPG2) follows the Peppas model with the highest value of regression (R² = 0.98509). Hence, from the results, these hydrogels could be a potential biomaterial for wound dressing in biomedical applications.