顶空衍生固相微萃取-气相色谱质谱法测定聚碳酸酯树脂中的环境雌激素

建立了固相微萃取-气相色谱质谱联用测定聚碳酸酯树脂中环境雌激素4-枯基苯酚和双酚A的分析方法。优化了固相微萃取纤维、萃取温度和时间、解吸时间、搅拌速度、pH等萃取条件及衍生化温度和时间、衍生化方式等衍生化条件，并对样品浸泡时间、浸泡温度等进行了研究。方法的线性范围为0．05μg/L～1mg／L，4-枯基苯酚和双酚A的检出限分别为50ng／L和0．5ng／L，相对标准偏差（RSD，n=5）分别为5．2％和1．6％，平均回收率（n=3）在90．50％～107．3％之间，该方法简单、快速、灵敏。     

固相微萃取-高效液相色谱法测定垃圾渗滤液中的双酚A

本文应用固相微萃取一高效液相色谱法(SPME—HPLC)分析了垃圾渗滤液中的痕量双酚A。对SPME的条件如测定模式、pH值、萃取时间、解吸方式、解吸溶剂、解吸时间和HPLC条件进行了优化。建立了SPME—HPLC分析垃圾渗滤液中痕量双酚A的方法。方法的线性范围为12．8～192μg／L,相关系数为0．9975,检出限为3．25μg／L(3σ,n=11)。以12．8μg／L的双酚A标准溶液平行测定11次,相对标准偏差(RSD)为4．4％,回收率为94．5％～103．3％。将其用于分析具有垃圾填埋场的渗滤液实际水样,结果十分满意。该方法具有快速、灵敏、简单、无溶剂的特点,适合于环境水样中痕量双酚A的分析。     

气相色谱-质谱法测定肝脏组织中盐酸克伦特罗和盐酸菜克多巴胺

建立了同时测定动物肝组织中盐酸克伦特罗和盐酸莱克多巴胺残留量的固相萃取-气相色谱-质谱分析方法。动物肝组织样品在碱化的条件下用乙酸乙酯和异丙醇混合溶剂提取，提取液浓缩后用乙酸乙酯溶解，然后再用稀盐酸反萃取去除脂肪，调pH值后经SCX固相萃取（SPE）柱净化，洗脱液经氮气吹干后经双三甲基硅基三氟乙酰氨（BSTFA）衍生，采用选择离子模式（盐酸克伦特罗：86、212、262、277，盐酸莱克多巴胺：163、192、234、250）进行测定，外标法定量。盐酸克伦特罗和盐酸莱克多巴胺的检出限分别为0．30和1．00μg／kg。盐酸克伦特罗添加浓度在1．0～5．0μg／kg范围内，添加回收率为77．4％～88．3％；相对标准偏差（RSD）为3．1％～5．1％；盐酸莱克多巴胺添加浓度在4．0～20．0μg／kg，添加回收率为69．8％～82．1％；相对标准偏差（RSD）为3．5％～4．9％；衍生物的峰面积与被测物浓度分别在0．003～1．00mg／L和0．012～4．00mg／L范围内呈良好的线性关系，线性回归系数均大于0．999。     

固相萃取-气相色谱-质谱法测定猪组织中沙丁胺醇残留量

建立了动物组织中沙丁胺醇残留量固相萃取-气相色谱-质谱分析方法。动物组织样品经过葡萄糖醛甙酶酶解后调节pH至9．5，然后用异丙醇／乙酸乙酯混合溶剂液液分配去除杂质，旋转浓缩后用乙酸铵缓冲溶液溶解经SCX固相萃取（SPE）柱净化，洗脱液经氮气吹干后用双三甲基硅基三氟乙酰氨（BSTFA）衍生，采用选择离子模式（86、350、369、440）进行测定，外标法定量。检出限为0．10μg/kg。在添加浓度0．5～5．0μg/kg范围内，平均添加回收率在66．4％～82．4％，相对标准偏差（批内）（CV）在3．5％～5．9％之间；批间（CV）在2．2％～4．8％之间。衍生物的峰面积与样品浓度在0．002～0．50mg／L范围内呈良好的线性关系，线性回归系数大于0．999。     

固相萃取-气相色谱法测定地下水中痕量酞酸酯的研究

本文建立了固相萃取-气相色谱法定量分析地下水中酞酸酯类（PAEs）有机污染物的方法。利用正交试验和单因素实验对影响回收率的4个主要因素（洗脱溶剂种类、水样体积、洗脱溶剂体积、固相萃取小柱填料量）进行了萃取条件的优化。综合考虑各方面因素后确定的最佳萃取条件为：二氯甲烷和丙酮为洗脱剂,体积8mL、0．5L水样、柱填料500mg。方法线性范围0．05～10．00μg／L,检出限0．05～0．341ng／L,相对标准偏差0．038％～1．107％。该方法应用于江汉平原地下水中PAEs测定,取得满意结果。     

反胶束萃取-高效液相色谱法测定磺酸型偶氮染料

建立了水中磺酸偶氮染料甲基橙（MO）、刚果红（CR）和酸性铬兰K（ACBK）的反胶束萃取-离子对高效液相色谱定量检测的方法。采用Hypersil C18柱（250×4．6mm,5μm）,流动相为V（甲醇）／V（水）=63：37（含10mmol／L的KH2PO4、4mmol／L的四丁基溴化铵,KOH调pH=7．0）,流速为0.8mL／min,MO、CR和ACBK检测波长分别为449nm、505nm和526nm。结果表明,染料的回收率为92．9％～102．1％,相对标准偏差为0．9％～2．3％,水中MO、CR和ACBK的检出限分别为0．6μg／L、1．2μg／L和1．3μg／L。     

固相萃取-高效液相色谱法测定水中BPA、NP和OP含量

采用国产新型D4020大孔吸附树脂自制固相萃取柱,研究了柱长、上样速度、样品溶液的pH、盐浓度等因素对壬基酚、辛基酚和双酚A吸附率的影响,确定了最佳固相萃取条件,建立了固相萃取-高效液相色谱测定水中痕量壬基酚、辛基酚和双酚A的分析方法.该法双酚A、壬基酚和辛基酚的检出限分别为0.432 μg/L、0.998 μg/L和1.336 μg/L,回收率为91%～96%,相对标准偏差(RSD)为1.5%～5.6%.方法简便快速、成本低廉,灵敏度高,准确度好,用于实际水样分析,取得满意结果.     

尼龙6纳米纤维膜固相膜萃取-高效液相色谱法测定塑料瓶装矿泉水中双酚A

采用静电纺丝法制备尼龙6纳米纤维膜,结合固相膜萃取-高效液相色谱法测定了矿泉水中的双酚A。对洗脱溶剂及其体积、进样速度、样品体积、样品pH值、尼龙6纳米纤维膜的用量、及其活化方式和使用次数等影响因素进行了研究。结果表明:10mL样品调至pH8.0后,以3mL/min流速通过1.5mg尼龙6纳米纤维膜,300μL甲醇即可将膜上吸附的双酚A完全洗脱,每张膜至少可重复使用6次。在此最优化条件下,方法的线性范围为0.20～20.0μg/L;检出限为0.15μg/L,膜内和膜间的相对标准偏差均小于4.5%(n=6)。本方法应用于6种不同品牌的矿泉水中双酚A的分析测定,在1.0μg/L加标水平下,测得回收率为95.0%,双酚A测得浓度低于0.30μg/L。与固相萃取方法相比,本方法高效、环保,表明尼龙6纳米纤维膜是极具潜力的萃取介质     

HPLC-ICP-MS测定中药中砷的形态

报道了高效液相色谱-电感耦合等离子体质谱（HPLC—ICP-MS）联用技术测定中药中砷的形态，采用阴离子交换柱，以0．2mmol／L EDTA和2mmol／L NaH2PO4的溶液为流动相，pH6．0，流速为1．0mL／min，成功分离了亚砷酸（AsⅢ）、砷酸（AsV）、甲基砷（MMA）和二甲基砷（DMA）。检出限分别为0．67μg／L（AsⅢ），0．85μg／L（DMA），0．43μg／L（MMA），0．70μg／L（AsV）。中药样品经过（1＋1）甲醇和水的溶液超声提取，离心、过滤、氮气吹干甲醇，超纯水定容。样品加标平均萃取回收率分别为：92．8％（AsⅢ），108％（DMA），104％（MMA），101％（AsV），相对标准偏差（RsD，n=7）均小于10％。     

利用炭石灰固相萃取测定水中的有机氯农药

研究利用炭石灰作为反相固定相,萃取水中12种有机氯农药,并用GC／ECD检测。实验表明,炭石灰萃取水中有机氯的效果与商品柱的萃取效果相当,对于200mL添加40ng有机氯农药混合标准溶液水样,其目标化合物的回收率为70％～122％,检出限为0．023～0．124μg／L,多次重复实验测定的相对标准偏差为3．40％～12．9％（n=5）。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.