不同衬底上的ZnO薄膜紫外光致发光

用射频磁控溅射法在蓝宝石、硅和石英衬底上沉积出具有好的择优取向的多晶ZnO薄膜. 在270 nm波长的光激发下室温下可观察到显著的紫外光发射（波长为356 nm）和较弱的蓝光发射（波长为446 nm）. 经高温退火后薄膜的结晶质量显著提高, 在蓝宝石、石英衬底上沉积的薄膜，其积分发光强度分别增加了7倍和14倍.而硅衬底上的膜发光强度增强不太显著.紫外光发射源于电子的带间跃迁，而蓝光发射是由电子从氧空位浅施主能级到价带顶的跃迁引起的. 关键词： ZnO薄膜 射频磁控溅射 紫外发光 退火     

Influence of excitation light wavelength on the photoluminescence properties for ZnO films prepared by magnetron sputtering

Highly orientated polycrystalline ZnO films were deposited on sapphire, silicon and quartz substrates at room temperature by r.f. magnetron sputtering. Different photoluminescence (PL) spectra were observed when excited with different wavelength light. A UV emission peak (356 nm) and a blue peak (446 nm) were generated for the films on sapphire, silicon and quartz substrates, and only the 446 nm blue emission appeared for the films on glass substrates when the wavelength of the excitation light was 270 nm. With increasing the wavelength of the excitation light up to 300 and 320 nm, the UV emission disappeared for films on various substrates and the wavelength of the PL peaks increased up to 488 and 516 nm, respectively. When the wavelength of the excitation light increased to 398 nm, the PL spectrum becomes a wide band that is consistent with three emission peaks.     

射频磁控溅射法制备ZnO薄膜的发光特性

利用射频磁控溅射法在硅衬底上制备出具有（002）择优取向的氧化锌薄膜，用波长为300nm的光激发，观察到在446nm处有一强的光致发光峰，它来自于氧空位浅施主能级上的电子到价带上的跃迁。并讨论了发光峰与氧压的关系以及退火对它的影响，且给出了解释。     

磁控溅射制备ZnO薄膜的结构及发光特性研究

采用射频反应磁控溅射法在玻璃衬底上制备出具有c轴高择优取向的ZnO薄膜,利用X射线衍射、扫描探针显微镜及荧光分光光度法研究了生长温度对ZnO薄膜微观结构及光致发光特性的影响。结果表明,合适的衬底温度有利于提高ZnO薄膜的结晶质量;在室温下测量样品的光致发光谱(PL),观察到波长位于400 nm左右的紫光、446 nm左右的蓝色发光峰及502 nm左右微弱的绿光峰,随衬底温度升高,样品的PL谱中紫光及蓝光强度逐渐增大,同时,绿光峰的强度也表现出一定程度的增强。经分析得出紫光应是激子发光所致,而锌填隙则是引起蓝光发射的主要原因,502 nm左右的绿光峰应该是氧的深能级缺陷造成的。此外,还测量了样品的吸收谱,并结合样品吸收谱的拟合结果对光致发光机理的分析作了进一步的验证。     

Effects of sapphire substrates surface treatment on the ZnO thin films grown by magnetron sputtering

The surface treatment effects of sapphire substrate on the ZnO thin films grown by magnetron sputtering were studied. The sapphire substrates properties have been investigated by means of atomic force microscopy (AFM) and X-ray diffraction rocking curves (XRCs). The results show that sapphire substrate surfaces have the best quality by CMP with subsequent chemical etching. The surface treatment effects of sapphire substrate on the ZnO thin films were examined by X-ray diffraction (XRD) and photoluminescence (PL) measurements. Results show that the intensity of (0 0 2) diffraction peak of ZnO thin films on sapphire substrates treated by CMP with subsequent chemical etching was strongest, FWHM of (0 0 2) diffraction peak is the narrowest and the intensity of UV peak of PL spectrum is strongest, indicating surface treatment on sapphire substrate preparation may improve ZnO thin films crystal quality and photoluminescent property.     

Effect of substrate and annealing on the structural and optical properties of ZnO:Al films

ZnO:Al thin films with c-axis preferred orientation were deposited on glass and Si substrates using RF magnetron sputtering technique. The effect of substrate on the structural and optical properties of ZnO:Al films were investigated. The results showed a strong blue peak from glass-substrate ZnO:Al film whose intensity became weak when deposited on Si substrate. However, the full width at half maxima (FWHM) of the Si-substrate ZnO:Al (0 0 2) peaks decreased evidently and the grain size increased. Finally, we discussed the influence of annealing temperature on the structural and optical properties of Si-substrate ZnO:Al films. After annealing, the crystal quality of Si-substrate ZnO:Al thin films was markedly improved and the intensity of blue peak (∼445 nm) increased noticeably. This observation may indicate that the visible emission properties of the ZnO:Al films are dependent more on the film crystallinity than on the film stoichiometry.     

Dependence of photoconductivity on the crystallite orientations and porosity of polycrystalline ZnO films

Hexagonal ZnO films deposited on quartz glass, sapphire and glass substrates by sol–gel coating are found to be randomly oriented; maximum randomness is found in the film on quartz glass substrate. All the films are ultra-violet (UV) sensitive at around 360 nm sensitivity being maximum for the film with maximum randomness in the crystallite orientations. The film on quartz showed the lowest dark current and maximum photoresponse, which is related to the lowering of the barrier heights, introduced by the adsorbed oxygen at the grain boundaries. Faster decay in photocurrent is observed for the film deposited on glass, which is attributed due to the smaller crystallite sizes with porous microstructure of the film. PACS 73.61.Ga; 68.55.Jk; 73.50.Pz     

Structural and PL properties of Cu-doped ZnO films

Cu-doped ZnO films with hexagonal wurtzite structure were deposited on silicon (1 1 1) substrates by radio frequency (RF) sputtering technique. An ultraviolet (UV) peak at ∼380 nm and a blue band centered at ∼430 nm were observed in the room temperature photoluminescent (PL) spectra. The UV emission peak was from the exciton transition. The blue emission band was assigned to the Zn interstitial (Zn_i) and Zn vacancy (V_Zn) level transition. A strong blue peak (∼435 nm) was observed in the PL spectra when the α_Cu (the area ratio of Cu-chips to the Zn target) was 1.5% at 100 W, and ZnO films had c-axis preferred orientation and smaller lattice mismatch. The influence of α_Cu and the sputtering power on the blue band was investigated.     

两步溶液法制备亚微米ZnO棒阵列及其退火后的发光

通过改变溶液浓度、酸碱度等生长条件,用两步化学溶液沉积法在玻璃衬底上制备出有序排列的亚微米级ZnO棒阵列,棒的截面呈正六边形,直径约为200~500nm。测量了样品的XRD谱和扫描电镜像,证明这些样品都是六方纤锌矿结构的ZnO单晶,且以[002]方向择优生长。将样品退火前后的PL光谱进行比较分析,发现退火后样品的发射光谱中紫外峰消失而长波段的红色发光峰红移并且增强(峰位由630nm左右移到720nm),而其激发光谱中的室温激子激发峰也增强。当退火时间增加到6h后,出现了由430nm的蓝峰和505nm绿峰组成的宽谱带蓝绿色发射。并对发光机理进行了讨论。     

Single violet luminescence emitted from ZnO films obtained by oxidation of Zn film on quartz glass

The photoluminescence (PL) emission properties of ZnO films obtained on quartz glass substrate by the oxidation of Zn films were studied. The strong single violet emission centering about 413-424 nm was observed in the room temperature PL spectra of the ZnO films. The intensity of violet emission increased and the peak position shift from 424 to 413 nm with increasing oxygen pressures. The violet emission was attributed to the electron transition from the valence band to interstitial zinc (Zn_i) level under low oxygen pressure conditions (50-500 Pa). Under high oxygen pressure conditions (5000-23,000 Pa), both interstitial zinc (Zn_i) and zinc Vacancy (V_Zn) were thought to be responsible for the violet emission.     

Influence of Al-doping on the structure and optical properties of ZnO films

Al-doped ZnO (ZnO:Al) thin films with c-axis preferred orientation were deposited on glass substrates using the radio frequency reactive magnetron sputtering technique. The effect of Al concentrations on the microstructure and the luminescence properties of the ZnO:Al thin films were studied by atomic force microscopy (AFM), X-ray diffraction (XRD), and fluorescence spectrophotometer. The results showed that the crystallization of the films was promoted by appropriate Al concentrations; the photoluminescence spectra (PL) of the samples were measured at room temperature. Strong blue peak located at 437 nm (2.84 eV) and two weak green peaks located at about 492 nm (2.53 eV) and 524 nm (2.37 eV) were observed from the PL spectra of the four samples. The origin of these emissions was discussed. In addition, absorption and transmittance properties of the samples were researched by UV spectrophotometer; the UV absorption edge shifted to a shorter wavelength first as Al was incorporated, and then to a longer wavelength with the increasing Al concentrations. The optical band gaps calculated based on the quantum confinement model are in good agreement with the experimental values.     

Effect of temperature on pulsed laser deposition of ZnO films

ZnO thin films have been deposited on Si(1 1 1) substrates at different substrate temperature by pulsed laser deposition (PLD) of ZnO target in oxygen atmosphere. An Nd:YAG pulsed laser with a wavelength of 1064 nm was used as laser source. The influences of the deposition temperature on the thickness, crystallinity, surface morphology and optical properties of ZnO films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), selected area electron diffraction (SAED), photoluminescence (PL) spectrum and infrared spectrum. The results show that in our experimental conditions, the ZnO thin films deposited at 400 °C have the best surface morphology and crystalline quality. And the PL spectrum with the strongest ultraviolet (UV) peak and blue peak is observed in this condition.     

Effects of substrate on surface morphology, crystallinity, and photoluminescence properties of sputtered ZnO nano films

Effects of substrate on crystallinity, surface morphology, and luminescence properties of radio frequency sputtered zinc oxide (ZnO) thin films were investigated. A variety of materials such as Si (100), Si (111), Al₂O₃, quartz, and silicon carbide (SiC) wafers were examined as substrates for deposition of ZnO thin films. The results showed smooth and uniform growth of c-axis orientation films. The thickness of the layers was about 50 nm. The average grain sizes of films were about 10, 13, and 12 nm for Si (111), quartz, and SiC samples, respectively. The deposited film on Al₂O₃ showed the largest grain size, about 500 nm. Grazing incidence x-ray diffraction patterns of the samples revealed that sputtered layers on Al₂O₃ and quartz had better crystallinity with higher peak at (002) orientation compared to Si and SiC substrates. Moreover, the Al₂O₃ sample exhibited a weak peak at position of (100) planes of ZnO too. The photoluminescence spectra of the samples showed a typical luminescence behavior with a broad UV band, including a main peak at around 388 nm and a weak shoulder peak at around 381 nm, corresponding with bound excitonic recombination and free excitonic recombination, respectively. The luminescence peak revealed that the intensity of UV emission is not necessarily dependent on the grain sizes and the micro-structural quality of ZnO films.     

氧氩比对纳米ZnO薄膜蓝光发射光谱的影响

利用射频磁控溅射方法,在石英表面上制备了具有良好的c轴取向的纳米ZnO薄膜。室温下,在300 nm激发下,在450 nm附近观测到ZnO薄膜的蓝光发射谱(430~460 nm)。分析了气氛中氧气与氩气比对薄膜质量及蓝光发射光谱的影响,给出了纳米ZnO薄膜光致发光谱(PL)的积分强度和峰值强度与氧氩比关系。探讨了纳米ZnO薄膜的蓝光光谱的发射机制,初步证实了ZnO蓝光发射(2.88~2.69 eV)来自氧空位(VO)形成的浅施主能级上的电子至价带顶的跃迁。     

脉冲激光沉积方法制备ZnO薄膜生长参量对发光特性的影响

用脉冲激光沉积（PLD）方法在Si（111）衬底上制备了ZnO薄膜。以325nmHe-Cd激光器为光源对薄膜进行了荧光光谱分析,用X射线衍射仪（XRD）和原子力显微镜（AFM）分别对薄膜的结构和形貌进行了分析。脉冲激光沉积方法的主要生长参量为氧压、激光重复频率、生长温度和激光能量。通过控制这些参量变量,研究了这些参量对ZnO薄膜发光特性的影响,得到了用于紫外发光的ZnO薄膜生长的优化条件：发现在温度为650℃左右、氧压50Pa左右、频率5Hz左右的范围内能得到半峰全宽较窄,强度较大的紫外发光峰。分析认为紫外峰主要是由激子辐射复合发光形成的,绿光带主要和Ozn的存在密切相关,氧空位是蓝光发射的重要原因。     

CVD两步法生长ZnO薄膜及其光致发光特性

用CVD两步法在常压下于p型Si(100)衬底上沉积出具有较好择优取向的多晶ZnO薄膜。在325nm波长的光激发下,室温下可观察到显著的紫外光发射(峰值波长381nm)。高温退火后氧空位缺陷浓度增加,出现了一个450~600nm的绿光发光带,发光峰值在510nm。作为比较,用一步法生长的ZnO薄膜结晶质量稍差。在其PL谱中不仅有峰值波长389nm的紫外发射而且还出现了一个很强的蓝光发光中心(峰值波长437nm),退火后同样产生绿光发光带。对这两种绿光发光带的发光机制进行了研究,认为前者源于VO,而后者与O_Zn有密切的关系。     

Effects of the substrate and oxygen partial pressure on the microstructures and optical properties of Ti-doped ZnO thin films

Ti-doped ZnO (ZnO:Ti) thin films were deposited on the glass and Si substrates using radio frequency reactive magnetron sputtering. The effects of substrate on the microstructures and optical properties of ZnO:Ti thin films were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and a fluorescence spectrophotometer. The structural analyses of the films indicated that they were polycrystalline and had a hexagonal wurtzite structure on different substrates. When ZnO:Ti thin film was deposited on Si substrate, the film had a c-axis preferred orientation, while preferred orientation of ZnO:Ti thin film deposited on glass substrate changed towards (1 0 0). Finally, we discussed the influence of the oxygen partial pressures on the structural and optical properties of glass-substrate ZnO:Ti thin films. At a high ratio of O₂:Ar of 18:10 sccm, the intensity of (0 0 2) diffraction peak was stronger than that of (1 0 0) diffraction peak, which indicated that preferred orientation changed with the increase of O₂:Ar ratios. The average optical transmittance with over 93% in the visible range was obtained independent of the O₂:Ar ratio. The photoluminescence (PL) spectra measured at room temperature revealed four main emission peaks located at 428, 444, 476 and 527 nm. Intense blue-green luminescence was obtained from the sample deposited at a ratio of O₂:Ar of 14:10 sccm. The results showed that the oxygen partial pressures had an important influence for PL spectra and the origin of these emissions was discussed.     

Photoluminescence in amorphous (PbLa)TiO3 thin films deposited on different substrates

Pb_1−XLa_XTiO₃ thin films, (X=0.0; 13 and 0.27 mol%) were prepared by the polymeric precursor method. Thin films were deposited on Pt/Ti/SiO₂/Si (1 1 1), Si (1 0 0) and glass substrates by spin coating, and annealed in the 200-300°C range in an O₂ atmosphere. X-ray diffraction, scanning electron microscopy and atomic force microscopy were used for the microstructural characterization of the thin films. Photoluminescence (PL) at room temperature has been observed in thin films of (PbLa)TiO₃. The films deposited on Pt/Ti/SiO₂/Si substrates present PL intensity greater than those deposited on glass and silicon substrates. The intensity of PL in these thin films was found to be dependent on the thermal treatment and lanthanum molar concentration.     

非掺杂ZnO薄膜中紫外与绿色发光中心

用直流反应溅射方法在硅衬底上淀积了ZnO薄膜,测量它们的光致发光(PL)光谱,观察到两个发光峰,峰值能量分别为3.18(紫外峰,UV)和2.38eV(绿峰).样品用不同温度分别在氧气、氮气和空气中热处理后,测量了PL光谱中绿峰和紫外峰强度随热处理温度和气氛的变化,同时比较了用FP-LMT方法计算的ZnO中几种本征缺陷的能级位置.根据实验和能级计算的结果,推测出ZnO薄膜中的紫外峰与ZnO带边激子跃迁有关,而绿色发光主要来源于导带底到氧错位缺陷(O_Zn)能级的跃迁,而不是通常认为的氧空 关键词： ZnO薄膜 热处理 光致发光光谱 缺陷能级     

硅衬底阳极氧化铝膜的荧光发射研究

报道了用电子束蒸发技术在硅守底上沉积，并于１５ｗｔ％Ｈ２ＳＯ４，温度２５℃和４０Ｖ直流电压条件下阳极氧化铝薄的制备（膜厚约４００ｎｍ）。研究了该阳极氧化铝膜的红外吸收光谱（ＦＴＩＲ）、光致荧光光谱（ＰＬ）和荧光激发光谱（ＰＬＥ）。发现其荧光光谱在２８０￣５００ｎｍ范围内由三个主发射带组成，其峰值分别位于３１２ｎｍ，３６７ｎｍ和４４９ｎｍ。所有这三个ＰＬ带，经分析都与阳极氧化铝膜中的氧化铝膜中的氧空