高分子型炭黑分散剂的合成及其性能研究

研究了嵌段型分分子颜料分散剂的合成及其有炭黑分散体系中的分散稳定作用。结果表明，高分子嵌段分散剂在炭黑分散体系中能明显改善分散稳定性。同时发现，嵌段分散剂的组成、结构及分子量对分散作用有综合影响。     

Surface-induced morphologies in thin films of a rod-coil diblock copolymer

A block copolymer containing a rodlike block is studied for its adsorption and formation of nanostructured thin films on the substrate surface. The block copolymer is poly(styrene-b-3-triethoxysilylpropylisocyanate) (PS-b-PIC) of which the PIC chain consists of repeating amide units with triethoxysilyl side groups. As the copolymer chains are adsorbed onto silica surfaces, the PIC blocks pack laterally on the plane in a smectic manner, and the PS chains segregate along the ordered PIC chains, resulting in stripe patterns. The width of the stripes formed on the silica surface appeared to be much larger that on the carbon surface. This was accounted for by the bilayered smectic packing of the rod blocks that is induced by rod-surface attractive interaction. The periodicity of the stripe pattern on the carbon surface indicates that interdigitated packing is preferred by the copolymers on the hydrophobic surface in a manner similar to those in the bulk state of rod-coils. Excess rod-coils on the bilayered smectic layer resulted in a terraced morphology due to large difference in the periodicity between the bilayered smectic layer at the substrate surface and the interdigitated smectic layer in the bulk.     

Effect of butadiene/styrene ratio,block structure and carbon nanotube content on the mechanical and electrical properties of thermoplastic elastomers after UV ageing

Thermoplastic elastomers based on a triblock copolymer styrene-butadiene-styrene (SBS) with different butadiene/styrene ratios, block structure and carbon nanotube (CNT) content were submitted to accelerated weathering in a Xenontest, in order to evaluate their stability to UV ageing. It was concluded that ageing mainly depends on butadiene/styrene ratio and block structure, with radial block structures exhibiting faster ageing than linear block structures. Moreover, the presence of carbon nanotubes in the SBS copolymer slows down the ageing of the copolymer. The evaluation of the influence of ageing on the mechanical and electrical properties demonstrates that the mechanical degradation is higher for the C401 sample, which is the SBS sample with the largest butadiene content and a radial block structure. On the other hand, a copolymer derivative from SBS, the styrene-ethylene/butadiene-styrene (SEBS) sample, retains a maximum deformation of ∼1000% after 80 h of accelerated ageing. The hydrophobicity of the samples decreases with increasing ageing time, the effect being larger for the samples with higher butadiene content. It is also verified that cytotoxicity increases with increasing UV ageing, with the exception of SEBS, which remains non-cytotoxic up to 80 h of accelerated ageing time, demonstrating its potential for applications involving exposure to the environment.     

Photodegradation of carbon monoxide–styrene copolymer in benzene and formation of block copolymer with methyl methacrylate

Photodegradation of carbon monoxide–styrene copolymer in benzene was investigated. In relation to the average number of main-chain scissions per macromolecule versus photoirradiation time, the straight line did not pass through the origin. This phenomenon was attributed to the presence of a labile bond from the carbonyl group in the main chain, in accordance with the results of Cameron and Lawrence which were found in the study of photodegradation of thermally polymerized polystyrene. In utilization of photodegradative behavior in carbon monoxide–styrene copolymer, a block copolymer of styrene with methyl methacrylate was prepared and was ascertained by precipitated fractionation, elementary analysis, and turbidimetry.     

Asymmetric ABC-triblock copolymer membranes induce a directed insertion of membrane proteins

Asymmetric molecules and materials provide an important basis for the organization and function of biological systems. It is well known that, for example, the inner and outer leaflets of biological membranes are strictly asymmetric with respect to lipid composition and distribution. This plays a crucial role for many membrane-related processes like carrier-mediated transport or insertion and orientation of integral membrane proteins. Most artificial membrane systems are, however, symmetric with respect to their midplane and membrane proteins are incorporated with random orientation. Here we describe a new approach to induce a directed insertion of membrane proteins into asymmetric membranes formed by amphiphilic ABC triblock copolymers with two chemically different water-soluble blocks A and C. In a comparative study we have reconstituted His-tag labeled Aquaporin 0 in lipid, ABA block copolymer, and ABC block copolymer vesicles. Immunolabeling, colorimetric, and fluorescence studies clearly show that a preferential orientation of the protein is only observed in the asymmetric ABC triblock copolymer membranes.     

Gas and liquid permeation properties of modified interfacial composite reverse osmosis membranes

Gas permeation tests using nitrogen, oxygen, hydrogen, helium and carbon dioxide were performed to assess how membrane modification procedures affect the separating layer morphology of thin-film composite reverse osmosis membranes. Gas selectivity data provided evidence for the presence of nanoscale separating layer defects in dry samples of six commercial membrane types. These defects were eliminated when the membrane surface was coated with a polyether–polyamide block copolymer (PEBAX 1657), as indicated by a 25-fold decrease in gas permeance and at least a 2-fold increase in most selectivity values. Treatment with n-butanol followed by drying reduced water flux and gas flux by 30% and 75%, respectively, suggesting that using n-butanol as a solvent for applying coatings negatively affects membrane performance. The results of this study demonstrate that gas permeation measurements can be used to detect morphological features that impact gas and water membrane flux.     

Synthesis of block copolymer poly (n-butyl acrylate)-b-polystyrene by DPE seeded emulsion polymerization with monodisperse latex particles and morphology of self-assembly film surface

Synthesis of poly (n-butyl acrylate)-b-polystyrene (PnBA-b-PSt) with high molecular weight in an environmentally benign medium was carried out in seeded emulsion polymerization, using a novel chain transfer active DPE (1,1-diphenylethylene) agent. Seed latex containing precursor P(nBA-DPE) was prepared first, and the second monomer styrene was swelled into seed latex particles, yielding block copolymer at high conversion. Structures as well as molecular weight of precursor and block copolymer were characterized by FTIR, (1)H NMR, and SEC, respectively. Furthermore, Transmission Electron Microscopy (TEM) observation and Laser Light Scattering (LLS) manifested that monodisperse latex particles were obtained. Self-assembly morphology of block copolymer membrane surface was examined by atom force microscopy (AFM). Phase separation was observed clearly, which was confirmed by the observation of two glass transitions in DSC curve.     

Nanostructured carbon arrays from block copolymers of polyacrylonitrile

Arrays of graphitic carbon nanoclusters were obtained by pyrolysis of nanoscale phase-separated block copolymers of polyacrylonitrile and poly(n-butyl acrylate). Upon heating in an inert atmosphere to temperatures ranging from approximately 400 to 1200 degrees C, polyacrylonitrile domains were converted into carbon nanoclusters, maintaining the overall shape and spacing, whereas the poly(n-butyl acrylate) phase was sacrificed. Preservation of the original nanoscale morphology of a block copolymer was possible only if pyrolysis was preceded by oxidation at temperatures of approximately 230 degrees C, in analogy with thermal stabilization of polyacrylonitrile precursor in the process used in the manufacturing of carbon fibers. Preorganization of the carbon precursor through self-assembly in block copolymers of polyacrylonitrile appears to be an attractive and robust strategy for templated synthesis of well-defined nanostructured carbon materials.     

A Molecular Photosensitizer in a Porous Block Copolymer Matrix-Implications for the Design of Photocatalytically Active Membranes

Recently, porous photocatalytically active block copolymer membranes were introduced, based on heterogenized molecular catalysts. Here, we report the integration of the photosensitizer, i. e., the light absorbing unit in an intermolecular photocatalytic system into block copolymer membranes in a covalent manner. We study the resulting structure and evaluate the orientational mobility of the photosensitizer as integral part of the photocatalytic system in such membranes. To this end we utilize transient absorption anisotropy, highlighting the temporal reorientation of the transition dipole moment probed in a femtosecond pump-probe experiment. Our findings indicate that the photosensitizer is rigidly bound to the polymer membrane and shows a large heterogeneity of absolute anisotropy values as a function of location probed within the matrix. This reflects the sample inhomogeneity arising from different protonation states of the photosensitizer and different intermolecular interactions of the photosensitizers within the block copolymer membrane scaffold.     

具有血液相容性的嵌段聚酯-聚醚接枝共聚物的合成

本文研究了嵌段聚酯-聚醚膜经紫外光活化后,于水溶液中铈盐引发亲水性单体丙烯酰胺在其表面上接枝共聚合反应。同时对接枝物进行了证实和表征。并通过活体动物血液灌流实验表明,此接枝共聚物具有良好的血液相容性。     

Microphase separation of weakly charged block polyelectrolyte solutions: Donnan theory for dynamic polymer morphologies

A mean-field dynamic density functional theory for the phase behavior of concentrated weakly charged block polyelectrolyte solutions is developed, using the Donnan membrane equilibrium approach to account for electrostatic interactions. In this limit all long-range electrostatic interactions are canceled and the net charge density in any region on a coarse-grained scale is zero. The phase diagram of a model triblock polyelectrolyte in solution as a function of the charge of the solvophilic block and the solvent concentration is established. Different mesoscopic structures (lamellar, bicontinuous, hexagonal, micellar, and dispersed coexisting phases) are formed depending on the copolymer charge asymmetry. It is found that upon changing the charge of the solvophilic copolymer block the polyelectrolyte solution does not follow the lyotropic sequence of phases of this polymer. Upon increase in the charge of the solvophilic blocks, changes in copolymer morphology take place by means of change in curvature of polymeric domains.     

Poly(phenylene oxide) copolymer anion exchange membranes

Poly(phenylene oxide) block and random copolymers are synthesized by oxidative polymerization of 2,6-dimethylphenol and 2,6-diphenylphenol for potential alkaline exchange membrane application. The copolymers are functionalized on the methyl substituted repeat units through a two-step process to produce pendent quaternary ammonium cationic groups. The amount of quaternary ammonium cations and the ion exchange capacity are quantified through titration measurements. Ionic conductivity of the copolymer membranes is measured by electrochemical impedance spectroscopy. Block copolymers show increased bromide conductivity at higher ion exchange capacities compared with the random copolymer analogs. The bromide conductivity for a block copolymer film with an ion exchange capacity of 1.27 mequiv/g reaches 26 mS/cm at 90 °C and 95% relative humidity. The hydroxide conductivity for the same film was measured to be 84 mS/cm at 80 °C and 95% relative humidity. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1770–1778, 2013     

Transparent,Versatile Chemical Vapor Sensor Using Supramolecular Assembly of Block Copolymer and Carbon Nanotubes

Here, a simple and novel approach is reported for developing a new class of transparent chemical vapor sensors with a low power consumption, high sensitivity, good selectivity, and excellent environmental stability by depositing multiwalled carbon nanotubes on prepatterned polymer substrates using supramolecular assembly. The patterned polymer substrates were fabricated from block copolymers, whereas the supramolecular assembly between the carbon nanotubes and block copolymer is utilized for the selective localization of carbon nanotubes at the block copolymer–air interface. The thin film devices made from the block copolymer and carbon nanotubes are highly transparent (transmittance > 90%) and respond to a wide range of solvents of different polarity, both hydrophilic and hydrophobic, with good selectivity and fast response time.

     

Synthesis and solution behavior of carbon nanotubes decorated with amphiphilic block polyelectrolytes

The aqueous solubilization of carbon nanotubes (CNTs) with the aid of a block copolymer possessing one polyelectrolyte block (namely polystyrene-b-sodium (sulfamate/carboxylate polyisoprene)) is reported. The solubilization protocol, based on the co-dissolution of the copolymer and the CNTs, leads to the formation of supramolecular assemblies on the side walls of the tubes. Electron microscopy as well as infrared spectroscopy and thermogravimetric analysis were employed as meaningful probes to identify the adsorption of the polymer onto the surface of CNTs and the composition of the final hybrid material. Viscosity measurements on solutions of the copolymer decorated CNTs indicate that the polyelectrolyte effect, which is observed in the case of net polymers, is preserved in a lesser extent in the case of the copolymer/CNTs dispersions.     

Solid-supported block copolymer membranes through interfacial adsorption of charged block copolymer vesicles

The properties of amphiphilic block copolymer membranes can be tailored within a wide range of physical parameters. This makes them promising candidates for the development of new (bio)sensors based on solid-supported biomimetic membranes. Here we investigated the interfacial adsorption of polyelectrolyte vesicles on three different model substrates to find the optimum conditions for formation of planar membranes. The polymer vesicles were made from amphiphilic ABA triblock copolymers with short, positively charged poly(2,2-dimethylaminoethyl methacrylate) (PDMAEMA) end blocks and a hydrophobic poly( n-butyl methacrylate) (PBMA) middle block. We observed reorganization of the amphiphilic copolymer chains from vesicular structures into a 1.5+/-0.04 nm thick layer on the hydrophobic HOPG surface. However, this film starts disrupting and dewetting upon drying. In contrast, adsorption of the vesicles on the negatively charged SiO2 and mica substrates induced vesicle fusion and formation of planar, supported block copolymer films. This process seems to be controlled by the surface charge density of the substrate and concentration of the block copolymers in solution. The thickness of the copolymer membrane on mica was comparable to the thickness of phospholipid bilayers.     

Supramolecular Complex of Poly(styrene)-b-Poly(4-vinylpyridine) and 1-Pyrenebutyric Acid in Thin Film

Summary: Here, we have described a novel supramolecular complex (SMC) between poly(styrene)-b-poly(4-vinylpyridine) (PS-b-P4VP) and 1-pyrenebutyric acid (PBA) and studied of its self assembly in thin film. PBA will make supramolecular complex with the P4VP block due to strong hydrogen bonding between the carboxylic group of 1-pyrenebutyric acid and pyridine ring of P4VP. The formation of supramolecular complex between PS-P4VP and PBA through hydrogen bonding is investigated through FTIR study. The supramolecular complex of PS-b-P4VP and 1-pyrenebutyric acid changed the block copolymer morphology from cylindrical to lamella in thin film due to the increase of the volume fraction of P4VP (PBA). In both cases (parent block copolymer and SMC), the microdomains are oriented normal to the substrate after annealing in a selective solvent. Pure block copolymer shows cylindrical morphology with a periodicity of ∼26 nm, whereas the SMC shows lamellar morphology with a periodicity of ∼ 29 nm. After fabricating the thin film from SMC, 1-pyrenebutyric acid can be easily removed by dissolving the thin film in ethanol to transform the block copolymer thin film into nanotemplate or membrane.     

One-pot synthesis of block copolymers in supercritical carbon dioxide: a simple versatile route to nanostructured microparticles

We present a one-pot synthesis for well-defined nanostructured polymeric microparticles formed from block copolymers that could easily be adapted to commercial scale. We have utilized reversible addition-fragmentation chain transfer (RAFT) polymerization to prepare block copolymers in a dispersion polymerization in supercritical carbon dioxide, an efficient process which uses no additional solvents and hence is environmentally acceptable. We demonstrate that a wide range of monomer types, including methacrylates, acrylamides, and styrenics, can be utilized leading to block copolymer materials that are amphiphilic (e.g., poly(methyl methacrylate)-b-poly(N,N-dimethylacrylamide)) and/or mechanically diverse (e.g., poly(methyl methacrylate)-b-poly(N,N-dimethylaminoethylmethacrylate)). Interrogation of the internal structure of the microparticles reveals an array of nanoscale morphologies, including multilayered, curved cylindrical, and spherical domains. Surprisingly, control can also be exerted by changing the chemical nature of the constituent blocks and it is clear that selective CO(2) sorption must strongly influence the block copolymer phase behavior, resulting in kinetically trapped morphologies that are different from those conventionally observed for block copolymer thin films formed in absence of CO(2).     

Synthesis of proton‐conducting block copolymer membranes composed of a fluorinated segment and a sulfonic acid segment

Diblock copolymer membranes having a fluorinated segment and a sulfonic acid segment were prepared by living radical polymerization, solution casting, and crosslinking, followed by heat treatment. Diblock copolymers of 2,3,4,5,6‐pentafluorostyrene (PFS)/4‐(1‐methylsilacyclobutyl)styrene (SBS) and neopentyl styrenesulfonate (SSPen) (poly(PFS‐co‐SBS)‐b‐polySSPen)s were synthesized by nitoroxy‐mediated living radical polymerization. Self‐standing crosslinked membranes were obtained by casting a THF solution of the block copolymer with Pt catalyst. Heat treatment of the membrane at 230 °C induced decomposition of the neopentyl sulfonate esters to provide block copolymer membranes having a fluorinated segment and a free sulfonic acid segment. It was confirmed that the block copolymer with a high sulfonic acid content exhibited high ion exchange capacity and high proton conductivity as well as high thermal stability. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4479–4485, 2008     

Single chain distribution analysis near a substrate using a combined method of three-dimensional imaging and SCF simulation

The effect of preferential wetting of one of the constituent block chains and corresponding block copolymer morphologies to a carbon substrate is studied from a molecular level. The single chain distribution of the block copolymer was estimated as a function of the distance from the substrate by a combined method of transmission electron microtomography (TEMT) and self-consistent field (SCF) simulation. The former provides three-dimensional (3D) morphological information of cylindrical microdomains near the surface, while the latter utilizes the 3D morphology to quantitatively determine the interaction between the block chains and substrate, which is further used to estimate the single chain distribution of one of the block chains, i.e., the subchain, of the matrix. It was found that the subchains in the vicinity of the wetting layer are substantially compressed, while the radius of gyration of the subchain at a distance L (L is the interlayer distance of the cylindrical microdomains from the substrate) has already reached the same value as that in the bulk, indicating that the propagation of the surface interaction is limited to one layer. The methodology developed in this study can be used not only to estimate the surface effect on polymer chains for a variety of different surfaces, but also to provide a means to understand complicated block copolymer morphologies from a molecular level.     

Effect of water content on the size and membrane thickness of polystyrene-block-poly(ethylene oxide) vesicles

The asymmetric amphiphilic block copolymer polystyrene962-block-poly(ethylene oxide)227(PS962-b-PEO227) canforms micelles with N, N-dimethylformamide(DMF) as co-solvent and water as selected solvent, and when the water content of the mixed solvent is higher than 4.5 wt%, the vesicle will be dominated. This work finds that once vesicles are formed in the DMF-water mixed solvent, the vesicle size and membrane thickness can be tuned by further increasing water content. As the water fraction elevated from 4.8 wt% to 13.0 wt%, the vesicle size dercreases from 246 nm to 150 nm, while the membrane thickness increases from 28 nm to 42 nm. In addition, the block copolymer packing and the free energy are analyzed as the vesicle size becomes small and the membrane becomes thick.