Copolymerization of ethylene with a homologous series of vinyl esters

The effect of the alkyl group on the relative reactivity of a homologous series of vinyl esters (2) has been studied with ethylene (1) as reference monomer, tert-butyl alcohol as solvent, at 62°C and 35 kg/cm². The experimental method was based on frequent measurement of the monomer feed composition throughout the copolymerization reaction by means of quantitative gas-chromatographic analysis. Highly accurate monomer reactivity ratios were estimated in a statistically justified manner by a nonlinear least-squares method applied to the integrated copolymer equation. The reactivity of the vinyl ester monomers towards an ethylene radical increased with decreasing electron-with-drawing ability of the ester group. All vinyl ester radicals considered turned out to have the same preference for their own monomer over ethylene (constant r₂ = 1.50). Reactivity ratios are discussed in terms of the Q–e scheme and the Taft relation. It appeared that chiefly polar factors contribute to the observed relative reactivity, while probably resonance stabilization only plays a minor part. Steric hindrance seems to impair monomer reactivity, only from vinyl pivalate on. Relative reactivities of the vinyl esters are compared with literature values, where other reference monomers have been used.     

Syntheses of Bile Pigments. Part 16. Synthesis of a vinyl-substituted 2,3-Dihydrobilinedione: Possible role of this new class of bile pigments in phycobilin biosynthesis

The total synthesis of racemic cis-2,3,18¹, 18², -tetrahydroprotobiliverdin IXα dimethyl ester ( 19b ), which is identical with the dimethyl ester of rac- 4 , is described (Scheme 2). Under virtually neutral conditions, in solution, this bile pigment isomerized within a few min to racemic Z-phycocyanobilin dimethyl ester (rac- 5b ). Likewise, acid-catalyzed allyl rearrangement of 3-vinyl-substituted cis- and trans-2,3-dihydrodipyrrin-1(10H)-ones 11c and 13c , respectively, yielded the corresponding ethylidene derivatives. In this case, however, the E-isomer was formed stereo selectively from both substrates. The above results prove that, if protobiliverdin IXα ( 2 ) is transformed enzymatically to its 2,3,18¹, 18²-tetrahydro derivative, the latter would isomerize spontaneously to phycocyanobi-lin. The biosynthesis of bacteriochlorophyll a and b from a common precursor bearing a vinyl group at C(8)may be straightforwardly explained in the same way.     

Surface‐initiated ring‐opening polymerization of p‐dioxanone on Wang resin bead

Biodegradable poly(p‐dioxanone) (PPDO) was formed on Wang resin surface by surface‐initiated ring‐opening polymerization (SI‐ROP). The SI‐ROP of p‐dioxanone (PDO) was achieved by heating a mixture of Tin(II) bis(2‐ethylhexanoate) [Sn(Oct)₂], hydroxyl functionalized Wang resin, and PDO in anhydrous toluene at 80 °C. The resultant polymer‐grafted Wang resin (Wang‐g‐PPDO) was characterized by fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), optical microscopy (OM), and field‐emission scanning electron microscopy (FE‐SEM). The FTIR spectra of Wang‐g‐PPDO show peak characteristic of PPDO at 2943 cm^?1 (? C? H stretch), at 1741 cm^?1 (? C?O stretch), and 1136 cm^?1 (C? O? C stretch) indicating the formation of ester linkage between PPDO and hydroxyl terminated Wang resin. The DSC thermogram show melting peak corresponding to PPDO polymer on Wang resin surface. Thermogravimetric investigation shows increase in PPDO content on the Wang resin surface in terms of percentage of weight loss with increase in reaction time. The OM and SEM photographs clearly show the formation of PPDO polymer on the Wang resin surface without altering the spherical nature of Wang resin bead. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1178–1184, 2008     

Reactions of trifluoroacetic acid with poly(vinyl alcohol) and its model compounds. Effect of neighboring hydroxyl groups on the reaction

Reactions of trifluoroacetic acid with poly(vinyl alcohol) and various model alcohols were investigated by observing the fluorine and the proton magnetic resonance spectra of the reaction mixtures. At equilibrium the degree of conversion to ester under given conditions decreased in the order isopropanol, pentane-2,4-diol, heptane-2,4,6-triol and poly(vinyl alcohol). Therefore the equilibrium constant for esterfication of a hydroxyl group is depressed by the presence of neighboring hydroxyl groups. It was observed that the steric structures of the models and polymers also affect the equilibrium position of the reaction and this is mainly ascribable to the fact that meso (isotactic) molecules react more slowly with the acid than do racemic (syndiotactic) molecules. In acid-catalyzed acetylation of the model alcohols with acetic acid no similar dependence on the steric configuration was found. Therefore trifluoroacetylation seems to be specific in this respect.     

Synthesis and characterization of the n-butyl palmitate as an organic phase change material

In this research, the n-butyl palmitate was synthesized using the esterification reaction of the PA with n-butanol. The ¹H nuclear magnetic resonance and Fourier transform infrared illustrated that the hydroxyl group and carboxyl group disappeared, and the ester bond appeared after the reaction, explaining that n-butyl palmitate was successfully fabricated. The differential scanning calorimetry indicated that the phase-transition temperature and latent heat are 12.6 °C and 127.1 J g^?1, which was suited to use in low-temperature fields such as food, pharmaceutical, and biomedical. The thermogravimetric analysis suggested that it had great thermal stability during the phase change process. In addition, the thermal conductivity of the n-butyl palmitate was slightly higher than other fatty acid ester, and the 500 thermal cycles test results indicated that it had excellent thermal reliability. Therefore, the n-butyl palmitate is deduced to share great thermal energy storage ability in terms of latent heat thermal energy system applications.

     

Preparation of Macroporous Poly(vinyl alcohol-co-triallyl isocyanurate)Beads Bearing Aminocarboxylic Acid as Functional Groups by Suspension Polymerization

Macroporous poly(vinyl acetate-co-triallyl isocyanurate)beads were prepared with suspension polymerization method.The copolymer beads were then transformed into poly(vinyl alcohol-co-triallyl isocyanurate)by ester exchange reaction.Aminocarboxylic acids were immobilized on the copolymer beads by the esterification of hydroxyl groups with diethyl-lenetriaminepentaacetic bisanhydride,The weak acid exchange capacities,specific surface areas and mean pore diameters of the rsultant resin beads were measured.     

Synthesis of Chlorophyll a Labeled at C(32) from Pheophorbide a Methyl Ester

[3²-¹⁴C]Chlorophyll a ( 10b ) was synthesized from pheophorbide a methyl ester ( 5a ) in a seven-step partial synthesis. The key intermediate pheophorbide d methyl ester ( 6 ) was obtained by ozonolysis of the vinyl group of 5a in 91% yield. Selective reduction of the CHO group of 6 gave the corresponding alcohol 7 , and conversion of the latter to the phosphonium bromide 8 yielded after Wittig reaction with [¹⁴C]paraformaldehyde, [3²-¹⁴C]pheophorbide a methyl ester ( 5b ). The final transformation to the title compound was achieved by acid hydrolysis of 5b , esterification with natural phytol to [3²-¹⁴C]pheophytin a ( 9b ), and eventual insertion of a Mg²⁺ ion.     

Chemical modification of hydroxyl groups of poly(vinyl alcohol) by a glycosidation reaction

A new procedure for chemical modification of poly(vinyl alcohol) (PVA) was established by a glycosidation reaction of hydroxyl groups in PVA with triacetylated sugar oxazoline 1 . ¹H and ¹³C NMR analyses indicated that triacetylated N‐acetyl‐D‐glucosamine (GlcNAc) was introduced onto a PVA backbone selectively via a β‐O‐glycoside linkage. Deacetylation of triacetylated GlcNAc‐substituted PVA 2 resulted in GlcNAc‐substituted PVA 3 in good yield. These modified PVAs 2 and 3 exhibited solubilities and thermal properties different from the original PVA.     

Studies on chiral thiophosphoric acids and their derivatives: 4. The stereospecific synthesis of optically active O-ethyl O-phenyl O-(1-methyl-2-ethoxycarbonyl) vinyl phosphorothionate

The stereoisomers (3 and 4) of O-ethyl O-phenyl O-(1-methyl-2-ethoxycarbonyl) vinyl phosphorothionate have been synthesized by the reaction of optically active O-ethyl O-phenyl phosphorothiochloride 2 with ethyl acetoacetate under different conditions. 3 (100% Z-isomer, determined by ¹H NMR) was synthesized by the reaction of 2 with ethyl sodio-acetoacetate in the mixed solvent of 1:3 toluene-dioxane at 50°C. 4 (>95% E-isomer) was obtained by the reaction of 2 with ethyl acetoacetate in presence of t-BuOK in DMSO at 15°C. 100% E-isomer 4 was separated from crude 4(>95% E-isomer) by column chromatography on silica gel (petroleum ether-ether 6:1). By this reaction either Z- or E-isomers were formed with inversion of the configuration at phosphorus atom. Thus, six stereoisomers of 3 and 4 which were prepared from 2 (RS, S, R) by the above method namely (RS)-Z, (R)-Z, (S)-Z and (RS)-E, (R)-E, (S)-E.     

聚乙烯基酯树脂整体柱的制备及其对免疫球蛋白的分离

以一种新型的材料聚乙烯基酯树脂（甲基丙烯酸间苯二酚二缩甘油酯）同时为单体和交联剂,以偶氮二异丁基腈（AIBN）为引发剂,以十六醇为制孔剂制备所得的聚合物整体柱,经化学修饰后,考察其作为HPLC的固定相对免疫球蛋白等进行分离,结果表明分离效果良好,适合作为HPLC的固定相。     

Thermal curing behavior of MWCNT modified vinyl ester‐polyester resin suspensions prepared with 3‐roll milling technique

This study aims to investigate the curing behavior of a vinyl ester‐polyester resin suspensions containing 0.3 wt % of multiwalled carbon nanotubes with and without amine functional groups (MWCNTs and MWCNT‐NH₂). For this purpose, various analytical techniques, including Differential Scanning Calorimetry (DSC), Fourier infrared spectroscopy (FTIR), Raman Spectroscopy, and Thermo Gravimetric Analyzer (TGA) were conducted. The resin suspensions with carbon nanotubes (CNTs) were prepared via 3‐roll milling technique. DSC measurements showed that resin suspensions containing CNTs exhibited higher heat of cure (Q), besides lower activation energy (E_a) when compared with neat resin. For the sake of simplicity of interpretation, FTIR investigations were performed on neat vinyl ester resin suspensions containing the same amount of CNTs as resin. As a result, the individual fractional conversion rates of styrene and vinyl ester were interestingly found to be altered dependent on MWCNTs and MWCNT‐NH₂. The findings obtained from RS measurements of the cured samples are highly proportional to those obtained from FTIR measurements. TGA measurements revealed that CNT modified nanocomposites have higher activation energy of degradation (E_d) compared with the cured polymer. The findings obtained revealed that CNTs with and without amine functional groups alter overall thermal curing response of the surrounding matrix resin, which may probably impart distinctive characteristics to mechanical behavior of the corresponding nanocomposites achieved. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1511–1522, 2009     

Investigation of infrared calibration methods for application to the study of methyl methacrylate polymerization

Infrared spectroscopy has been used to monitor the polymerization of methyl methacrylate. Concentrations of methyl methacrylate in the reaction mixture were determined by use of three calibration methods. Classical quantitative analysis was used to measure the height of the stretching vibration bands of the vinyl group at 1639 cm^–1. A calibration procedure using the considerably higher intensity of the C = O stretching vibration band of the carbonyl ester group at 1725 cm^–1 seemed useful only for high concentrations of methyl methacrylate, i.e. at the beginning of reaction, because this band overlaps that of poly(methyl methacrylate). Use of second-derivative spectra and measuring their values at 1725 cm^–1 enabled estimation of ten times lower concentrations of methyl methacrylate the calibration using the band from the vinyl group.     

Kinetic study of the crosslinking reaction of 1,2‐polybutadiene with dicumyl peroxide in the absence and presence of vinyl acetate

The crosslinking reaction of 1,2-polybutadiene (1,2-PB) with dicumyl peroxide (DCPO) in dioxane was kinetically studied by means of Fourier transform near-infrared spectroscopy (FTNIR). The crosslinking reaction was followed in situ by the monitoring of the disappearance of the pendant vinyl group of 1,2-PB with FTNIR. The initial disappearance rate (R₀) of the vinyl group was expressed by R₀ = k[DCPO]^0.8[vinyl group]^−0.2 (120 °C). The overall activation energy of the reaction was estimated to be 38.3 kcal/mol. The unusual rate equation was explained in terms of the polymerization of the pendant vinyl group as an allyl monomer involving degradative chain transfer to the monomer. The reaction mixture involved electron spin resonance (ESR)-observable polymer radicals, of which the concentration rapidly increased with time owing to a progress of crosslinking after an induction period of 200 min. The crosslinking reaction of 1,2-PB with DCPO was also examined in the presence of vinyl acetate (VAc), which was regarded as a copolymerization of the vinyl group with VAc. The vinyl group of 1,2-PB was found to show a reactivity much higher than 1-octene and 3-methyl-1-hexene as model compounds in the copolymerization with VAc. This unexpectedly high reactivity of the vinyl group suggested that an intramolecular polymerization process proceeds between the pendant vinyl groups located on the same polymer chain, possibly leading to the formation of block-like polymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4437–4447, 2004     

Grafting of Polymers onto a Crosslinked Polymer Carrying Carboxyl Groups as a Model Compound for Carbon Black

Abstract

A cation-exchange resin (a crosslinked polymer carrying carboxyl groups) was used as a model compound for carbon black, and the grafting of several polymers to the resin was investigated. Reaction of acyl chloride groups that had been placed on the ion-exchange resin with polymers having hydroxyl or amino groups, such as polypropylene glycol, polyethylene glycol, polybutadiene glycol, polyvinyl alcohol, silicone diol, silicone diamine, and polyethyleneimine, resulted in grafting to the ion-exchange resin. In further experiments, primary amino groups were placed on the cation-exchange resin by reaction of acyl chloride groups with ethylenediamine. It was found that ring-opening polymerization of γmethyl L-glutamate N-carboxyanhydride is initiated by the amino groups on the resin, and polypeptide was grafted from the cation-exchange resin. Therefore, the reactivity of carboxyl groups on the resin was found to be similar to that on carbon black. However, carboxyl groups on the resin failed to initiate the cationic polymerization of vinyl monomers, in contrast to those on carbon black. This suggested that the acidity of carboxyl groups on carbon black is greater than on the cation-exchange resin.     

Facile Synthesis of Alkylidene Phthalides by Rhodium-Catalyzed Domino C−H Acylation/Annulation of Benzamides with Aliphatic Carboxylic Acids

The Rh-catalyzed ortho-C(sp²)−H functionalization of 8-aminoquinoline-derived benzamides with aliphatic acyl fluorides generated in situ from the corresponding acids has been developed. This reaction initiated with 8-aminoquinoline-directed ortho-C(sp²)−H acylation, which was accompanied by subsequent intramolecular nucleophilic acyl substitution of amide group to produce alkylidene phthalides This approach exhibits high stereo-selectivity for Z-isomer products, and tolerates a variety of functional groups as well as aliphatic carboxylic acids with diverse structural scaffolds.     

Propylene sorption and coordinative interactions for poly(N‐vinyl pyrrolidone‐co‐vinyl acetate)/silver salt complex membranes

When poly(N‐vinyl pyrrolidone‐co‐vinyl acetate) (PVP‐co‐PVAc) containing amide and ester groups were complexed with silver salts to form silver polymer electrolyte membranes, their separation performance of propylene/propane mixtures showed the high selectivity of propylene over propane of 55 and the high mixed gas permeance of 12 GPU (1 GPU = 1.0 × 10^?6 cm³(STP) cm^?2 s^?1 cmHg^?1). The separation performance strongly depends on the composition of the copolymer: the higher concentration of PVP in the copolymer, the better separation performance was achieved. These results suggest that the amide group is more effective in facilitated propylene transport than the ester group, primarily due to the stronger interaction of the silver ions with the amide than the ester oxygens, as demonstrated by FT‐IR and FT‐Raman spectroscopies. In‐situ FT‐IR spectra upon propylene sorption also demonstrate that the interaction strength of the silver ions with the ligands is arranged: amide > C?C > ester. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2263–2269, 2007     

Acetalization of poly(vinyl alcohol) by a fatty aldehyde in water medium: Model study,kinetics, and structure analysis

Acid catalyzed poly(vinyl alcohol) (PVA) acetalization was investigated in aqueous medium at 80 °C for a PVA concentration of 8 wt %. The reactant, 10‐undecenal, was composed of a long alkyl chain with a vinyl end group, and the functionalization reaction was studied in heterogeneous media for low reactant concentrations (from 0.33 to 2.0 mol % compared with PVA hydroxyl groups concentration). First, the reaction was scrutinized with pentane‐2,4‐diol, as a model compound of PVA. Besides the expected reaction, the oxidation of the aldehyde into 10‐undecenoic acid in the presence of water was evidenced. This carboxylic acid appeared unreactive toward esterification of pentane‐2,4‐diol and PVA in water. Characterization of acetal stereochemical structure formed on the PVA backbone was performed by NMR spectroscopy in accordance to the model approach. A protocol based on ¹H NMR analysis was developed to quantify grafted aldehyde, residual aldehyde, and created carboxylic acid through direct sampling of the reaction medium. Conversions and reaction rate constants were calculated for pH ranging from 1 to 3. Finally, the acetalization yield was found to be enhanced at low pH and, in such conditions, the oxidation reaction contribution was limited. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 661–671     

Fragmentation characteristics of hydroxycinnamic acids in ESI‐MSn by density functional theory

This work aims to analyze the electrospray ionization multistage mass spectrometry (ESI‐MSⁿ) fragmentation characteristics of hydroxycinnamic acids (HCAs) in negative ion mode. The geometric parameters, energies, natural bond orbitals and frontier orbitals of fragments were calculated by density functional theory (DFT) to investigate mass spectral fragmentation mechanisms. The results showed that proton transfer always occurred during fragmentation of HCAs; their quasi‐molecular ions ([M − H]⁻) existed in more than one form and were mainly with the lowest energy. The fragmentation characteristics included the followings: (1) according to the different substitution position of phenolic hydroxyl group, the ring contraction reaction by CO elimination from benzene was in an increasingly difficult order: m‐phenolic hydroxyl > p‐phenolic hydroxyl > o‐phenolic hydroxyl; and (2) ortho effect always occurred in o‐dihydroxycinnamic acids (o‐diHCAs), i.e. one phenolic hydroxyl group offered H⁺, which combined with the other one to lose H₂O. In addition, there was a nucleophilic reaction during ring contraction in diHCAs that oxygen atom attacked the carbon atom binding with the other phenolic hydroxyl to lose CO₂. The fragmentation characteristics and mechanism of HCAs could be used for analysis and identification of such compounds quickly and effectively, and as reference for structural analogues by ESI‐MS. Copyright © 2017 John Wiley & Sons, Ltd.     

Surface grafting of polymers onto inorganic ultrafine particles: Reaction of functional polymers with acid anhydride groups introduced onto inorganic ultrafine particles

The surface grafting onto inorganic ultrafine particles, such as silica, titanium oxide, and ferrite, by the reaction of acid anhydride groups on the surfaces with functional polymers having hydroxyl and amino groups was examined. The introduction of acid anhydride groups onto inorganic ultrafine particle was achieved by the reaction of hydroxyl groups on these surfaces with 4-trimethoxysilyltetrahydrophthalic anhydride in toluene. The amount of acid anhydride groups introduced onto the surface of ultrafine silica, titanium oxide, and ferrite was determined to be 0.96, 0.47, and 0.31 mmol/g, respectively, by elemental analysis. Functional polymers having terminal hydroxyl or amino groups, such as diol-type poly(propylene glycol) (PPG), and diamine-type polydimethylsiloxane (SDA), reacted with acid anhydride groups on these ultrafine particles to give polymer-grafted ultrafine particles: PPG and SDA were considered to be grafted onto these surfaces with ester and amide bond, respectively. The percentage of grafting increased with increasing acid anhydride group content of the surface: the percentage of grafting of SDA (M_n = 3.9 × 10³) onto silica, titanium oxide, and ferrite reaching 64.7, 33.7, and 24.1%, respectively. These polymer-grafted ultrafine particles gave a stable colloidal dispersion in organic solvents.     

Theoretical and Experimental Insights of Benzimidazole Catalyzed by the Epoxy–Acrylic Acid Reaction

This study focuses on the experimental and molecular-level investigation of epoxy acrylate formation. Epoxy acrylate vinyl ester resin was prepared by a reaction of diglycidyl ether of bisphenol-A-based epoxy resin and acrylic acid, using benzimidazole as a catalyst. It was confirmed that benzimidazole can effectively catalyze this reaction. FTIR analysis of the product revealed a simple addition esterification reaction between the epoxide group and carboxylic group of acrylic acid excluding the side reactions (e.g., etherification). DFT computational studies were performed to theoretically explore the insights of reaction mechanisms. The calculations revealed that the benzimidazole-catalyzed reaction dominates the uncatalyzed reaction. A comparison of calculated activation energies showed that concerted mechanisms are less significant in such reactions owing to their high activation barriers.