Vapor-phase graft copolymerization of vinyl chloride and vinylidene chloride onto polypropylene fibers by simultaneous irradiation technique

The vapor-phase graft copolymerization of vinyl chloride and vinylidene chloride onto polypropylene fibers was studied by a simultaneous γ-irradiation technique. The weight increase during irradiation due to the grafting in monomers at constant vapor pressure was measured by a sensitive spring balance. The sorption of both monomers onto unirradiated polypropylene fibers was also measured. The graft copolymerization reaction was suppressed with increasing irradiation temperature, and the overall activation energies of grafting were negative in both monomers, ?2.4 kcal/mole for vinyl chloride and ?6.3 kcal/mole for vinylidene chloride. The initial rate of grafting increased linearly with the vapor pressure of monomers. The above dependence was found to parallel the sorption of monomers on polypropylene fibers. The reaction rates were proportional to the 0.9 power of the dose rate in both monomers. The relationship between the grafting and the sorption of monomers was discussed on the basis of kinetics.     

Carbonization of polytetrafluoroethylene surface by UV-induced grafting of vinylidene chloride

A method has been developed for modifying the surface layer of polytetrafluoroethylene by incorporation of poly(vinylidene chloride) via UV radiation-initiated graft polymerization of vinylidene chloride from the vapor phase using a PRK-4 mercury lamp. By the subsequent treatment of the composition with aqueous ammonia, dehydrochlorination (carbonization) of the grafted poly(vinylidene chloride) has been performed. The kinetics of UV grafting and the distribution of the carbonized phase in the polytetrafluoroethylene matrix have been studied. A material with the carbonized surface layer of a 10—30 μm thickness and a contact angle of about 57° remaining stable over time has been obtained.     

偏氯乙烯悬浮聚合反应速率模型

通过实验研究了偏氯乙烯悬浮聚合反应动力学,比较了偏氯乙烯与氯乙烯聚合动力学行为的异同.在假定偏氯乙烯聚合反应发生在单体相和液固界面两个区域的基础上,提出了偏氯乙烯沉淀聚合反应速率模型.模型预测的转化率值几乎在全转化率范围内都与本文的偏氯乙烯悬浮聚合实验结果一致.     

Electron-beam graft-modified membranes with externally controlled flux

Pre-irradiation grafting as a means to modify commerical poly(vinylidene fluoride) (PVDF) membranes has been studied. The membranes prepared were weak cation-exchange membranes (acrylic acid functionality), anion-exchange membranes (trimethyl ammonium functionality) and temperature-sensitive membranes (N-isopropyl amide functionality). Different graft loads were obtained by varying reaction time, radiation dose and in the case of acrylic acid the graft solution composition. The trimethyl ammonium chloride functionality was obtained by grafting vinyl benzyl chloride onto a PVDF membrane and aminating the benzyl chloride groups in a 45% trimethyl amine–water solution. For a membrane grafted with 9 wt% acrylic acid the flux increased approximately 70 times when the pH was decreased from 6 to 2. For a membrane with 5 wt% trimethyl ammonium functionality the flux increased both when pH was decreased below 3 and increased above 11. For a membrane grafted with 18 wt% N-isopropyl acrylamide a sharp increase of flux was observed when the temperature was raised above 32°C.     

ATRP法合成接枝共聚物PVDF-g-PNIPAAm及其分离膜的研究

以氯化亚铜(CuCl)/三(N,N-二甲基氨基乙基)胺(Me₆TREN)为催化配位体系, 用DMF作为溶剂, 通过原子转移自由基聚合(ATRP)方法直接在商用聚偏氟乙烯(PVDF)粉末上接枝温敏性材料N-异丙基丙烯酰胺(NIPAAm). 红外光谱(FTIR)和核磁共振(¹H NMR)分析表明, PNIPAAm成功接枝到了PVDF上. 考察了聚合反应时间及反应温度对接枝率的影响. 接枝共聚物以相转化法进行制膜, 通过纯水通量测试温敏性能, 结果表明, PVDF能成功用于ATRP反应, 当温度变化时所制备的PVDF-g-PNIPAAm共聚膜呈现出一定的温度敏感性能.     

Copolymers of vinyl and vinylidene chlorides with alkyl acrylates

High-molecular-weight copolymers of vinyl chloride and ethyl or butyl acrylate were prepared in high conversion and yield in the presence of boron trifluoride as the acrylate ester complexing agent. When the vinyl chloride monomer is in excess of equimolar amounts, the resulting copolymers are alternating; and when the alkyl acrylates are in excess, acrylate-rich copolymers are obtained. Ethylene–vinyl chloride–ethyl acrylate and propylene–vinyl chloride–ethyl acrylate terpolymers were also obtained with an ethyl acrylate content of 50 mole %. The relative reactivities of propylene, vinyl chloride, and ethylene in these polymerizations were 5.4, 3.8, and 1.0, respectively. Vinylidene chloride–ethyl acrylate copolymers that are nearly alternating and rich in acrylate or in vinylidene chloride have also been prepared. The monomer reactivity ratios for vinylidene chloride and ethyl acrylate in the presence of boron trifluoride are considerably lower than in its absence.     

聚丙烯酸酯/偏二氯乙烯/蒙脱土复合乳液的制备

以偏二氯乙烯和蒙脱土作改性剂,采用种子乳液聚合方法制备了聚丙烯酸酯 偏二氯乙烯/蒙脱土（PEA VDC/MMT）共聚物复合乳液,研究了蒙脱土质量分数对共聚物乳胶粒径、乳胶膜抗拉强度与断裂伸长率及热稳定性的影响。 结果表明,当蒙脱土质量分数从1%增加至5%时,PEA-VDC/MMT共聚物乳胶的平均粒径从141 nm增至243 nm;在蒙脱土质量分数为2%时, 乳胶膜的拉伸强度和断裂伸长率达到最大值,分别为3.23 MPa和1.330%。 PEA VDC共聚物的成碳率和热分解温度均随蒙脱土质量分数的增加而略有增加。     

Investigation of poly(vinylidene chloride) distribution in perfluorinated cation-exchange membranes MF-4SK upon UV- and γ-initiated graft polymerization

A new process for grafting poly(vinylidene chloride) (PVDC) to the membrane material MF-4SK by UV-initiated graft polymerization of the monomer from the gas phase has been developed. Modified membranes containing up to 20 wt % of UV-grafted PVDC have been obtained. Microphotographs of thin sections of the modified membranes have been investigated. It has been shown that the pretreatment of the membranes and variation of UV- or γ-grafting conditions make it possible to achieve an uniform distribution of grafted PVDC both along the thickness of the membrane and in a thin surface layer. The values of the parameters determining the character of the distribution have been estimated. Numerical simulation of the UV- and γ-initiated graft polymerization of VDC gave solutions for the grafted-PVDC distribution fitting with the experimental data.     

Degradation of vinylidene chloride/phenylacetylene (VDC/PA) copolymers. Effect of internal unsaturation on poly(vinylidene chloride) stability

The thermal degradation of vinylidene chloride/phenylacetylene copolymers containing small but varying amounts of phenylacetylene has been examined in both the solid phase and in bibenzyl solution. Incorporation of phenylacetylene into the poly(vinylidene chloride) structure greatly facilitates degradative dehydrochlorination. Indeed, the presence of phenylacetylene promotes the formation of polyene segments during the polymerization process so that all the copolymers, even at very low phenylacetylene loading, are tan in color. The decreased stability of polymers containing interal unsaturation arises from an increased rate of initiation for degradative dehydrochlorination. The propagation rate is largely unaffected by the level of unsaturation initially present in the polymer. The ratio of hydrogen chloride to stilbene formed for degradation of these copolymers in bibenzyl solution is approximately 35:1. This suggests that the chlorine atom of the initially-formed radical pair preferentially abstracts an adjacent hydrogen atom rather than interacting with solvent, i.e., the chain-carrying radical pair does not dissociate appreciably as the unzipping dehydrochlorination occurs. Thus random double bonds introduced in a variety of ways may be identified as principal defect sites responsible for the initiation of the degradative dehydrochlorination of poly(vinylidene chloride). Species which promote the degradation of poly(vinylidene chloride) probably do so by facilitating the introduction of random double bonds into the structure.     

Thermal decomposition of poly(vinylidene chloride) prepared in presence of oxygen

The thermal decomposition of poly(vinylidene chloride) was studied for samples prepared in the presence of oxygen. The products from both mass and aqueous suspension polymerizations show two modes of thermal decomposition. A rapid initial mode varies in rate and extent with the amount of oxygen present. A slower mode is unaffected by oxygen and in similar in rate to the polymer made in the absence of oxygen. The chief volatile products are phosgene and formaldehyde for the rapid decomposition and hydrogen chloride for the slow decomposition. The rapid decomposition is interpreted to be an unzipping reaction of a vinylidene chloride–oxygen alternating copolymer initiated by homolysis of a peroxide bond. The absence of significant amounts of hydrogen chloride during this stage of decomposition shows that none of the free radicals generated are capable of initiating a chain reaction that would unzip hydrogen chloride from the poly(vinylidene chloride) backbone. The presence of oxygen during the aqueous suspension polymerization correlates with the generation of hydrochloric acid in the aqueous phase. By analogy with the high temperature decomposition, the hydrochloric acid is believed to result primarily from the hydrolysis of phosgene produced by partial decomposition of the polyperoxide. Initiation of the decomposition is believed due to a reaction of the chain propagating radical.     

New copolymers of vinylidene fluoride

After a brief presentation of the standard non-functionalized copolymers of vinylidene fluoride, the preparation of new functionalized copolymers is described, by copolymerization of vinylidene fluoride, with other fluoromonomers and non-fluorinated monomers including at least one hydroxy or other functional group. The copolymers are analysed by the conventional methods. Examples of formulation show that these new copolymers are able to give coatings applicable outdoors and offering the same excellent durability as PVDF.     

One-Step Synthesis of 1,3-Bis(carboxymethyl) Adamantane

Addition of the carbonium ion to vinylidene chloride to give α-substituted acetic acid discovered by Bott^1,2 has been found of wide applicability. For example, the reaction of 1-bromo-, 1-hydroxy-, or 1-acetoxy-adamantane with vinylidene chloride in concentrated sulfuric acid gives a satisfactory yield of adamanty1-(1)-Acetic acid.^3,4     

Thermal degradation of vinylidene chloride/[4-(t-butoxycarbonyloxy)phenyl]methyl acrylate copolymers

Vinylidene chloride polymers containing comonomer units capable of consuming evolved hydrogen chloride to expose good radical-scavenging sites might be expected to display greater thermal stability than similar polymers containing simple alkyl acrylates as comonomer. Incorporation of a comonomer containing the phenyl t-butyl carbonate moiety into a vinylidene chloride polymer has the potential to afford a polymer with pendant groups which might interact with hydrogen chloride to expose phenolic groups. Copolymers of vinylidene chloride with [4-(t-butoxycarbonyloxy)phenyl]methyl acrylate have been prepared, characterized, and subjected to thermal degradation. The degradation has been characterized by thermal and spectroscopic techniques. The degradation of vinylidene chloride/[4-(t-butoxycarbonyloxy)phenyl]methyl acrylate copolymers is much more facile than the same process for similar copolymers containing either [4-(isobutoxycarbonyloxy)phenyl]methyl acrylate or methyl acrylate, a simple alkyl acrylate, as comonomer. During copolymer degradation, [4-(t-butoxycarbonyloxy) phenylmethyl acrylate units are apparently converted to acrylic acid units by extensive fragmentation of the sidechain. Thus, the phenyl t-butyl carbonate moiety does function as a labile acid-sensitive pendant group but its decomposition in this instance leads to the generation of a phenoxybenzyl carboxylate capable of further fragmentation.     

Carbon-chain polymers and copolymers Communication 9. Synthesis and properties of copolymers of vinylidene chloride with acrylonitrile and methyl methacrylate

Summary Copolymers of vinylidene chloride with acrylonitrile and methyl methacrylate were prepared with different compositions and the thermomechanical properties of these copolymers were examined.     

Thermal degradation of vinylidene chloride/vinyl chloride copolymers in the presence of N-substituted maleimides

As a consequence of their excellent barrier properties vinyl chloride/vinylidene chloride copolymers have long been prominent in the flexible packaging market. While these polymers possess a number of superior characteristics, they tend to undergo thermally- induced degradative dehydrochlorination at process temperatures. This degradation must be controlled to permit processing of the polymers. Three series of N-substituted maleimides (N-alkyl-, N-aralkyl, and N-aryl) have been synthesized, characterized spectroscopically, and evaluated as potential stabilizers for a standard vinyl chloride/vinylidene chloride (85 mass%) copolymer. As surface blends with the polymer, these compounds are ineffective as stabilizers. However, significant stabilization may be achieved by pretreatment of the polymer with N-substituted maleimides. The most effective stabilization of the polymer is afforded by N-aralkyl- or N-arylmaleimides, most notably, N-benzylmaleimide and N-p-methoxyphenylmaleimide.     

Laser-Raman spectra of vinyl chloride-vinylidene chloride copolymers

Several copolymers as well as homopolymers of vinylidene chloride and vinyl chloride have been examined by Raman spectroscopy. Probabilities of concentrations of monomer sequences have been calculated from known reactivity ratios. Surface scattering intensities at some frequencies were found to be linearly proportional to specific microstructure concentrations. Normalization of scattering intensities was accomplished using the intensity of the CH₂ asymmetric stretching mode at 2926 cm^-1, which is common to all samples examined. Good correlation was found for the concentrations of comonomer sequences {B}, {BB}, {BBB}, {AA} and {AAAA} in which A denotes vinylidene chloride and B vinyl chloride.     

Fluorocyclopropanes. IV. Copolymers of perfluorocyclopropene

Perfluorocyclopropene undergoes free-radical copolymerization with ethylene, isobutylene, cis- and trans-2-butene, vinyl acetate, methyl vinyl ether, vinyl chloride, styrene, acrylonitrile, tetrafluoroethylene, vinyl fluoride, and vinylidene fluoride. The copolymerization proceeds most readily with electron-rich olefins such as methyl vinyl ether (to yield a 1:1 copolymer), but conditions were found to give copolymers with electron-deficient olefins such as tetrafluoroethylene and vinylidene fluoride. Copolymers with methyl vinyl ether, tetrafluoroethylene, vinyl fluoride, and vinylidene fluoride were examined in detail. Evidence is presented that the perfluorocycloproply ring is incorporated intact into the copolymer and can be subsequently isomerized to a perfluoropropenyl unit by heating at 200–300°C.     

Thermal degradation of vinylidene chloride/4-vinylpyridine copolymers

Vinylidene chloride polymers are prominent in the barrier plastics packaging industry. They display good barrier to the transport of oxygen (to prevent spoilage of food items) and flavor and aroma constituents (to prevent 'scalping' on the supermarket shelf). However, these polymers undergo thermal dehydrochlorination during processing. This can lead to a variety of problems including the evolution of hydrogen chloride which must be scavenged to prevent its interaction with the metallic walls of process equipment. Such interaction leads to the formation of metal halides which act as Lewis acids to facilitate the degradation. A potentially effective means to capture hydrogen chloride generated might be to incorporate into the polymer a mild organic base. Accordingly, copolymers of vinylidene chloride and 4-vinylpyridine have been prepared and subjected to thermal aging. Results suggest that the pyridine moiety is sufficiently basic to actively promote dehydrochlorination in the vinylidene chloride segments of the polymer.     

Studies on molecular weight of poly ((vinylidene chloride)-co-(vinyl chloride)) in the suspension process

Various factors affecting the molecular weight of poly ((vinylidene chloride)-co-(vinyl chloride)) were studied in the paper. Mathematical models correlating intrinsic viscosity of the copolymer with concentrations of 1,2-dichloroethane and initiators, and temperature were proposed and may be used to control the molecular weight of the copolymer.     

Electron spin resonance spectra of polymers during fluorination

ESR spectra characteristic of peroxy radicals appeared rapidly in all of eleven hydrogen-containing polymers examined when treated with dilute fluorine. These radicals presumably result from the reaction of hydrocarbon and fluorocarbon radicals, existing at undetectably low steady-state concentrations, with the oxygen impurity content of commercial fluorine. In poly(vinylidene fluoride) films of thickness 11 and 58 μm the radical contents were nearly proportional to surface area rather than volume, in agreement with earlier reports of a shallow depth of penetration. Some polymers exhibited also or exclusively a broad spectral component, varying in character with the polymer; examples are polystyrene, polyethylene, poly (vinyl chloride), poly(vinylidene chloride), polyoctafluoropentadiene, polyhexafluoropropene, and a fluorinated graphite. The broad spectral component did not react with ordinary radical scavengers such as propylene and oxygen, and is probably not due to a fluorocarbon radical but to unknown transition metal fluorides.